Posiflex TM/LM-5011 Manuel utilisateur
- Catégorie
- Moniteurs à écran tactile
- Taper
- Manuel utilisateur
1
Package Contents
10.1” TM/LM-5011 POS Monitor……………………..………..……(x 1)
Mounting Kits ………………....…......................................................(x 1)
User Manual…………………………………………………………..(x 1)
FCC NOTES
This system meets industry & government requirements and applicable standards. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions manual, may cause interference to radio communications. It has been tested
and found to comply with limits for a Class A digital device pursuant to subpart B of Part 15 of
FCC Rules, which are designed to provide reasonable protection against interference when
operated in a commercial environment. Operation of this equipment in a residential area is likely
to cause interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential environment this
equipment may cause radio interference.
AVERTISSEMENT CE CLASSE A
Cet équipement est conforme à la classe A de CISPR 32. Dans un environnement résidentiel, cet
équipement peut provoquer des interférences radio.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than the
authorized technicians. The user should consult his/her dealer for the problem happening.
Warranty voids if the user does not follow the instructions in application of this merchandise. The
manufacturer is by no means responsible for any damage or hazard caused by improper application.
LIMITES DE GARANTIE
La garantie prend fin automatiquement lorsque la machine est ouverte par une personne autre que
les techniciens autorisés. L'utilisateur doit consulter son revendeur pour le problème qui se produit.
La garantie s'annule si l'utilisateur ne suit pas les instructions d'application de cette marchandise.
Le fabricant n'est en aucun cas responsable de tout dommage ou danger causé par une mauvaise
application.
TM/LM-5011
POS Monitor
User Manual
18370900010 Ver. A0
http://www.posiflex.com
2
警告
為避免電磁干擾，本產品不應安裝或使用於住宅環境。
WARNING
Power cord shall be connected to a socket-outlet with earthing connection.
ATTENTION
Le cordon d'alimentation doit être connecté à une prise de courant avec mise à la terre.
Views of TM/LM-5011
Front View
Rear View
Camera (Optional)
10.1” LCD Panel/P-CAP
Touch Panel
The Mark which indicating the
scanning area of the barcode scanner
40-Pin eDP Cable
Plastic Hinge Cover
Side Attachment
Cover
Barcode Scanner Window
(Optional)
3
Mounting your Monitor to ZT-series POS Terminals
The following instructions are provided to help you mount your TM/LM
monitor to Posiflex ZT-series POS terminals. During installation, please ensure
the terminal is properly turned off and disconnected from the power sources to
avoid potential hazards.
1. Rotate the screen to the horizontal position like the below picture, and
there is a base cover latch on the front side of the base stand.
2. Push the latch (toward left side) through the direction of the arrow like
below pictures, and then you can release the base cover.
3. Take off the base cover.
4
4. Rotate the screen to the upright position like below pictures.
5. There is a latch inside cable exit on the rear side of the POS terminal.
6. Push the latch with the thumb of the left hand, and then the touch monitor
will release automatically.
5
7. Open the touch monitor with two hands, and then you can do the
maintenance work.
8. Remove the attachment cover on the top side by pressing the inner hook
on both sides.
9. Fix the 2nd monitor with two thumbscrews, and then connect the eDP
cable to the ZT series main board.
Press.
6
10. Tilt the monitor screen to your desired angle. While setting up the tilting
adjustment, be careful NOT to press on the LCD panel.
Identifying your Monitor as Secondary Touchscreen Monitor
in Extended Mode
In the following section the related descriptions will be offered to help you set
up TM series as the extended monitor when you attempt to extend the desktop
across multiple monitors
For TM-5011 Model with P-CAP Touchscreen
If your monitors are TM-5011 models, you may configure the display settings
from Control Panel in Microsoft Windows to identify the monitor as the
secondary touchscreen monitor. Please go through the below steps to complete
configuration.
1. Make sure that the monitor is well connected to your POS terminal.
2. Go to Control Panel>Display Settings, change your display settings to
extended mode.
3. Go to Control Panel, and then click on
Tablet PC Settings item.
4. In Tablet PC Settings dialogue box, click
on Setup button.
7
5. Following the instruction shown on the screen, click on the screen that
you want to identify as the primary touchscreen display.
6. Press Enter button to proceed the configuration.
7. Click on the screen you want to use as the secondary touchscreen
display.
Powering ON/OFF your Monitor
To start up the monitor, please make sure that the monitor is well connected to
POS terminals and electricity is supplied to the monitor through POS terminal.
Installing Drivers
Please visit Posiflex official website to download and install the related drivers.
http://www.posiflex.com/en-global/Download/download)
Setting up Display Resolution for Your Monitor
The below chart defines the list of recommended display settings for
TM/LM monitor. Improper display configuration will prevent the monitor from
properly displaying the image and lead to a warning message of “out of range”
prompted on the screen.
10.1” TM/LM-5011
Display Resolution
Horizontal Frequency (KHz)
Refresh Rate (Hz)
640 x 480
31.5
60
37.9
72
37.5
75
800 x 600
37.9
60
48.1
72
46.9
75
1024 x 768
48.4
60
8
Display Resolution
Horizontal Frequency (KHz)
Refresh Rate (Hz)
1280 x 720
45.0
60
1280 x 800
49.7
60
Optional 2D Barcode Scanner Engine
Optional 2D barcode scanner engine is installed at the rear
cover, behind the Barcode Mark on the front panel. Scan
the below barcode to restore Auto Trigger defaults.
To do the further setting of the scanner engine, please find
the relevant user manual on Posiflex Global Website,
(http://www.posiflex.com/en-global/Download/download)
or contact the service team for technical support.
Specification
TM/LM-5011
Display
LCD Panel
10.1" TFT LCD
Resolution
1280(H) x 800 (V)
Active Area
216.96mm (H) x 135.60mm (V)
Viewing Angle
85/85/85/85 degree (U/D/L/R)
Contrast Ratio
800 : 1
Brightness
350 cd/m2
Power Supply
12V from ZT-series 40-Pin connector
Touch
Touch type
TM-5011: P-CAP; LM-5011: N/A
Interface
TM-5011: USB; LM-5011: N/A
Integrated module
Barcode Scanner
Optional, 2D barcode scanner on rear cover
Camera
Optional, 1MP wide angle or 5MP wide angle camera
module
Mechanical
Dimension
239.2 x 171.9 x 26.3 mm (WxDxH)
Net Weight
1 kg
Mounting
VESA mounting hole 75 x 75
Scan Area
10
<MEMO>
11
<MEMO>
12
<MEMO>
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Posiflex TM/LM-5011 Manuel utilisateur
- Catégorie
- Moniteurs à écran tactile
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Posiflex TM/LM-5011 User manual
Documents connexes
-
Posiflex TM/LM-5011P Manuel utilisateur
-
-
-
-
-
Posiflex RT-5115 Manuel utilisateur
-
Posiflex RT-6115 Manuel utilisateur
-
-
-