Posiflex TX-1000A/1000AE Manuel utilisateur

Posiflex
Marque
Posiflex
Modèle
TX-1000A/1000AE
Taper
Manuel utilisateur
1
Package Contents
POS box…………………………………..…………………………..(x 1)
Power adaptor………………………………..…………………….…(x 1)
Power cord………………………………………..…………………..(x 1)
User manual…………………………………………..……………....(x 1)
SOME IMPORTANT NOTES
FCC NOTES
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential environment
this equipment may cause radio interference.
AVERTISSEMENT CE CLASSE A
Cet équipement est conforme à la classe A de CISPR 32. Dans un environnement
résidentiel, cet équipement peut provoquer des interférences radio.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other
than the authorized technicians. The user should consult his/her dealer for the problem
happening. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
LIMITES DE GARANTIE
La garantie prend fin automatiquement lorsque la machine est ouverte par une personne
autre que les techniciens autorisés. L'utilisateur doit consulter son revendeur pour le
problème qui se produit. La garantie s'annule si l'utilisateur ne suit pas les instructions
d'application de cette marchandise. Le fabricant n'est en aucun cas responsable de tout
dommage ou danger causé par une mauvaise application.
TX-1000A/1000AE
Fanless POS Box
User Manual
14560902010 Ver. A0
http://www.posiflex.com
2
警告
為避免電磁干擾，本產品不應安裝或使用於住宅環境。
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to be
present.
CONSIGNES DE SÉCURITÉ
Cet équipement ne convient pas à une utilisation dans des lieux pouvant accueillir des
enfants.
WARNING
Power cord shall be connected to a socket-outlet with earthing connection.
ATTENTION
Le cordon d'alimentation doit être connecté à une prise de courant avec mise à la terre.
BATTERY WARNING
Risk of explosion if battery is replaced by an incorrect type. Dispose of expended battery in
accordance with local disposal regulations.
AVERTISSEMENT DE BATTERIE
Risque d'explosion si la batterie est remplacée par un type incorrect. Jetez la batterie
usagée conformément aux réglementations locales en matière d'élimination.
警告
本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之電池。
3
Views of the TX-1000A/1000AE
Front View of TX-1000A
Front View of TX-1000AE
Rear View
Bottom View
Rubber Pad
Rubber Pad
Power Button
24V PoweredUSB
Power Status LED Indicator
I/O Interface
Service Window
Micro USB Port
Power Button
Power Status LED Indicator
Micro USB Port
4
View of Rear I/O Interface of TX-1000A/1000AE
1
Mic-in & Line-out Combo
2
COM ports (RJ50)
3
COM ports (DB9)
4
12V poweredUSB (Only for
TX-1000AE)
5
USB 3.0 port
6
USB 2.0 ports
7
LAN port (RJ45)
8
HDMI ports
9
CR port
10
12 VDC-IN power jack
Connecting Power Adapter and I/O Cables
Please follow the steps described below to connect power adapter and I/O
cables.
1. Connect power adapter to DC-IN power connector on the I/O plate
2. Connect another end of power adapter to the electrical outlet.
CAUTION: On doing insertion or extraction of a cable connector, please
always hold the connector head itself instead of pulling the cable wire.
Doing this could damage the cables and ports, which is considered as an
artificial damage and is not covered by the warranty. The means of power
cord should be connected to a socket-outlet with earthing connection.
ATTENTION: Lors de l'insertion ou de l'extraction d'un connecteur de
câble, veuillez toujours tenir la tête du connecteur elle-même au lieu de
tirer le fil du câble. Cela pourrait endommager les câbles, ce qui est
considéré comme un dommage artificiel et n'est pas couvert par la
garantie. Le cordon d'alimentation doit être connecté à une prise de
courant avec mise à la terre.
2
10
5
1
6
7
8
4
9
3
5
Paring Information for HDMI Port & USB Port
There are two HDMI ports for TX-1000A/1000AE. Please refer to the below
table to connect the 1st monitor (main monitor) and the 2nd monitor.
1st Monitor
(Main Monitor)
2nd Monitor
Display
Touch
Display
Touch
TX-1000A
HDMI 1
USB 1
HDMI 2
USB 2-6
TX-1000AE
HDMI 1
Powered USB 1
or USB 1
HDMI 2
USB 2-6
Audio-out Control
For HDMI1:
You can find the APP named “AudioOutSwitch” in your
TX-1000A/1000AE system. This APP is for POS monitor
without built-in speaker which connected through HDMI1
interface. Therefore, if there is no built-in speaker in your
1st monitor, you can utilize this APP to switch the audio out
from the 1st monitor to the TX POS box.
Switch to Speaker: OFF
Click the button. When it shows OFF,
it means the audio would NOT come
out from the TX POS box.
Switch to Speaker: ON
Click the button. When it shows ON,
it means the audio would come out
from the TX POS box.
For HDMI2:
There is no audio out through HDMI2 interface.
Mounting the TX-1000A/1000AE on the Wall (Optional)
Please follow the steps described below to mount TX-1000A/1000AE onto the
wall using WB-4200 wall-mount kits.
1. Refer to WB-4200 installation guide to fix the
wall mount bracket onto the wall using plastic
anchors and screws.
6
2. Insert four screw bolts into the 4 screw bolt
holes.
3. Align 4 screw bolts to four mounting holes of
the wall-mount bracket as shown in the figure.
Then slide down the system along the rail until it
is locked into place with a click sound.
Powering ON/OFF TX-1000A/1000AE
Power ON TX-1000A/1000AE
Press down the power button and hold down the power button
for at least 3 seconds to power on TX-1000A/1000AE.
Power OFF TX-1000A/1000AE
In most cases, push the power button again to power off the
system. However, if TX-1000A/1000AE halts for unknown
reasons, please be advised to hold the power more than 10
seconds to initiate a forced shutdown.
Power Status LED Indicator
Power LED indicator is mainly responsible for notifying users of the current
system status by emitting various LED signals. The chart provided below will
offer helpful information that you need to interpret LED status.
LED
Status
Description
Power
Solid green
System power ON
Solid red
System standby
Storage
Flash green
Data access
Installing Optional Peripheral Devices
TX-1000A/1000AE can work with multiple optional peripheral devices, such
as LCD monitor, cash drawer and the like. Before installing an optional
peripheral device, make sure that the system is powered off and the external
power source is removed from the POS box to prevent electric hazard. For the
detailed instruction, refer to each of the user manuals of the optional peripheral
devices.
7
Operation Environment
To prevent TX-1000A/1000AE from overheating, it is suggested to position
your terminal in a well-ventilated working environment. In doing so, please be
advised to keep the POS box at least 25mm away from other devices to ensure
the machine is properly cooled down and functioning normally.
Specifications
TX-1000A/1000AE
CPU
Rockchip RK3399
System Memory
4GB DDR4
Storage Port
32GB / 64GB / 128GB eMMC + micro SD card slot
Power Supply
12V/40W power adaptor as default
12V/150W power adaptor with PoweredUSB
OS support
Android 10 w/GMS
Serial Port
2 x DB-9 COM ports + 1 x RJ-50 COM port + COM5/6 pin
headers in service window
5V/12V support on all COM ports
Standard USB Port
5 x USB 2.0 + 1 x USB 3.0 port
LAN Port
1 x 10 /100 /1000 Mb
Display Port
2 x HDMI port
CR Port
1 port, controlling 2 CRs
DC Jack
1 port
Expansion Slot
1 x M.2 socket (M.2 2230 / E key) for WiFi/BT module
Audio
1 x Mic-in & Line-out combo jack + 1 x internal speaker
LED Indicator
power status LED
PoweredUSB port
TX-1000A: N/A
TX-1000AE: 1 x 24V + 2 x 12V
Dimension
(W x D x H in mm)
220 mm x 202 mm x 56 mm
Weight
1.2 kg
Regulation Rules
FCC/CE
Environmental
Requirements
Operating : 0°C - 40°C, 20%RH - 90%RH
Storage : -20°C - 70°C, 10%RH - 90%RH
8
Outline Dimension
※ The product information and specifications are subject to change without prior
notice. To get the detailed information on TX-1000A/1000AE, please check this
model from Posiflex Global Website (http://www.posiflex.com/en-
global/Download/download).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Posiflex TX-1000A/1000AE Manuel utilisateur

Posiflex
Marque
Posiflex
Modèle
TX-1000A/1000AE
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes