1
Package Contents
15” P-CAP touch terminal with Gen 7E or
Gen 8E base (x 1)
Power adapter (x 1)
Power cord (x 1)
User manual (x 1)
Product Features
Fanless Design
Intel 4
th
generation Haswell CPU
New Gen 7E foldable base that allows JIVA XT Series to be configured
into different configurations.
New Gen 8E foldable base that integrates internal power adaptor and
Powered USB port into the base.
Mini-PCIe expansion slot
16760900030 Ver. B0
http://www.posiflex.com
XT-5315/5515/5515Pro
P-CAP Touch Terminal
User Manual
2
SOME IMPORTANT NOTES
FCC NOTES
This system meets industry & government requirements and applicable
standards. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions
manual, may cause interference to radio communications. It has been tested
and found to comply with limits for a Class A digital device pursuant to
subpart B of Part 15 of FCC Rules, which are designed to provide reasonable
protection against interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause interference
in which case the user at his own expense will be required to take whatever
measures to correct the interference.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential
environment this equipment may cause radio interference.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any
person other than the authorized technicians. The user should consult his/her
dealer for the problem happening. Warranty voids if the user does not follow
the instructions in application of this merchandise. The manufacturer is by no
means responsible for any damage or hazard caused by improper application.
警告使用者
這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，
在這種情況下，使用者會被要求採取某些適當的對策。
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to
be present.
3
CONSIGNES DE SÉCURITÉ
Cet équipement ne convient pas à une utilisation dans des lieux pouvant
accueillir des enfants.
BATTERY CAUTION NOTES
Dispose of used batteries according to the instructions.
Replacement of a battery with an incorrect type that can defeat a
safeguard (for example, in the case of some lithium battery types)
Disposal of a battery into fire or a hot oven, or mechanically crushing
or cutting of a battery that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of flammable
liquid or gas.
A battery subjected to extremely low air pressure that may result in an
explosion or the leakage of flammable liquid or gas.
BATTERIE ATTENTION NOTES
Jetez les piles usagées conformément aux instructions.
Remplacement d'une batterie avec un type incorrect qui peut annuler
une sauvegarde (par exemple, dans le cas de certains types de batterie
au lithium)
Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou
écrasement ou coupure mécanique d'une batterie pouvant entraîner une
explosion.
Laisser une batterie dans un environnement environnant à des
températures extrêmement élevées pouvant entraîner une explosion ou
la fuite de liquide ou de gaz inflammable.
Une batterie soumise à une pression atmosphérique extrêmement basse
pouvant provoquer une explosion ou une fuite de liquide ou de gaz
inflammable.
警告
本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之
電池。
4
Views of XT-5315/5515/5515Pro with Gen 7E Base
Front View
Rear View
Side View
Cable Cover
Neck Cover
HDD Cover
Cable Exit
XT-5315/5515/5515Pro
P-CAP Touch Panel
LED indicator
Power Button
Brightness Adjustment Button ＋
Brightness Adjustment Button －
Gen 7E Base
5
Bottom View
Views of XT-5315/5515/5515Pro with Gen 8E Base
Front View
Rear View
Cable Holder
Cable Exit
XT-5315/5515 /5515Pro
P-CAP Touch Panel
HDD Cover
Cable Cover
Neck Cover
Cable Exit
LED indicator
Rubber Feet with Fixing Screw
Rubber Feet with Fixing Screw
Gen 8E Base
6
Side View
Bottom View
View of I/O Interface of XT-5315/5515
Rubber Feet with Fixing Screw
Line Out/MIC-In
Combo Jack
USB 2.0
Ports
USB 3.0
Ports
DB9 COM Ports
VGA Port
CR Port
LAN Ports
12V BAT Port
DC IN
Power
Connector
Rubber Feet with Fixing Screw
RJ-50 COM Ports
UPS Battery
Compartment
Power Adapter
Compartment
PoweredUSB
Compartment
HD Compartment
Power Button
Brightness Adjustment Button ＋
Brightness Adjustment Button －
7
View of I/O Interface of XT-5515Pro
Positioning your POS for a Perfect Viewing Angle
The adjustable bases designed for XT-5315/5515/5515Pro come in two models,
Gen 7E/8E, and allow you to determine an ideal position for your terminal
using its unique tilt adjustment mechanism. As the below figures suggest, both
bases provide three standard positioning solutions for your terminal: Flat
Folded mode, Low Profile mode, and Full Extended mode.
XT-3515/5515/5515Pro with Gen 7E Base
Flat Folded mode
Low Profile mode
Full Extended mode
XT-3515/5515/5515Pro with Gen 8E Base
Flat Folded mode
Low Profile mode
Full Extended mode
Line Out/MIC-In
Combo Jack
USB 3.0
Ports
DB9 COM Ports
VGA Port
CR Port
LAN Port
12V BAT Port
DC IN
Power
Connector
RJ-50 COM Ports
HDMI Port
8
In general, XT-5315/5515/5515Pro will be set up beforehand in Flat Folded
mode and then packaged into the box for shipping. After it is unpacked, you
may re-adjust the terminal in either Low Profile mode or Full Extended mode
according to your situation. Below will provide instructions on how to adjust
the specific base connected to the POS system. As a reminder, please be
careful not to touch the LCD panel while setting up the tilt angle.
XT-3515/5515/5515Pro with Gen 7E Base
Please refer to the following instructions on how to switch among different
positioning modes to find an ideal viewing angle for XT-5315/5515/5515Pro
with Gen 7E base.
1. Unpack XT-5315/5515/5515Pro, which is
supposed to be set in flat folded mode, out of
the package box and then lay your POS
system on a flat surface.
2. Steady the base with one hand, and then tilt
the screen downwards.
3. Position your terminal in Full Extended mode
3.1 After grabbing the bottom edge of the screen with your hand, gently
move the screen upward until the screen is locked into place with a
click sound.
9
3.2 Support the screen with one hand holding onto its bottom edge.
Then, while pulling the lever backwards, move the display upwards
until the lever is snapped into the lower hook to raise the screen as
shown in the below figure.
3.3 With the screen facing toward you, tilt the
screen up or down to your desired angle.
Please do not press on the LCD panel while
setting up the tilt angle.
3.4 Remove the cable cover from the base.
3.5 Fix the base with two #6/32-14L screws.
Lever
Lower
hook
10
4. Return your terminal back to Flat Folded mode from Full Extended
mode.
4.1 Remove the cable cover from the base.
4.2 Remove the two screws from the base.
4.3 Tilt your screen in the horizontal position.
Remove the two screws.
11
4.4 Support the screen with one hand holding onto its bottom edge.
While pulling the lever backwards, move the display downwards
until the lever is lifted off the hook as shown in the figure.
4.5 Push the cable cover back.
4.6 Tilt the screen again to the horizontal
position.
5. Position the terminal in Low Profile mode.
5.1 Follow Step 4 to set up the termimal in Flat
Folded mode.
5.2 Tilt the screen all the way down
Hook
Lever
12
5.3 To tilt screen up or down to your desired
angle, please be advised to keep the base
steady with one hand to do so. Do NOT
press on the LCD panel while setting up the
tilt angle.
XT-5315/5515/5515Pro with Gen 8E Base
Please refer to the following instructions on how to switch among different
positioning modes to find an ideal viewing angle for XT-5315/5515/5515Pro
with Gen 8E base.
1. Unpack XT-5315/5515/5515Pro, which is
supposed to be set in flat folded mode, out
of the package box and then lay your POS
system on a flat surface.
2. While steadying the terminal with your
hand holding onto the base, tilt the screen
down.
3. Push the cable cover outwards to remove
it from the base.
13
4. Position your terminal in Full Extended mode.
4.1 Support the screen with one hand holding onto its bottom edge.
Then, while pulling the lever backwards, move the display upwards
until the lever is snapped into the lower hook to raise the screen as
shown in the below figure.
4.2 Tilt the screen up or down to your
desired angle. Please do not press on
the LCD panel while setting up the tilt
angle.
4.3 Fix the base with two #/6/32-14L screws.
4.4 Push the cable cover back.
Lower
hook
Lever
14
5. Position the terminal in Low Profile mode.
5.1 While keeping your terminal steady with your hand holding on to
the base, tilt your terminal down. Then, remove the cable cover
from the base.
5.2 Remove the two screws from the base.
5.3 Support the screen with one hand holding onto its bottom edge.
Then, while pulling the lever backwards, move the display
upwards or downwards until the lever is snapped into the upper
hook to lower the screen as shown in the below figure.
Remove the two screws.
Lever
Upper
hook
15
5.4 Push the cable cover back.
5.5 Tilt the screen up or down to your
desired angle. Please do not press on
the LCD panel while setting up the
tilt angle.
6. Return the terminal back to Flat Folded mode.
6.1 While steadying your terminal with your hand holding onto the
base, tilt your screen up.
6.2 Support the screen with one hand holding onto its bottom edge.
While pulling the lever backwards, release the lever back to the
point above the upper hook as shown in the figure.
Lever
Upper
hook
16
6.3 Push the cable cover back.
6.4 Tilt the screen to the horizontal position.
Connecting Power Adapter and I/O Cables
To have the terminal ready for operation, please connect the connector of
power adapter and all of the connectors of required I/O cables respectively to
the 12VDC-IN power jack and appropriate I/O ports. Please make sure that
each of the cables is fully connected to each of the correct ports. Damages due
to incorrect connection or orientation are not covered by product warranty!
Some cable connectors like the connectors of the COM or LAN cables have to
be gently inserted until a click is heard. It is recommended that the I/O ports,
such as COM port, should be screwed after the I/O cable connectors are
completely connected. And please make sure that each connector has to be
connected to the right peripheral device in the right way.
CAUTION: On doing insertion or extraction of a cable connector, please
always hold the connector head itself instead of pulling the cable wire.
Doing this could damage the cables and ports, which is considered as an
artificial damage and is not covered by the warranty. The means of power
cord should be connected to a socket-outlet with earthing connection.
ATTENTION: Lors de l'insertion ou de l'extraction d'un connecteur de
câble, veuillez toujours tenir la tête du connecteur elle-même au lieu de
tirer le fil du câble. Cela pourrait endommager les câbles, ce qui est
considéré comme un dommage artificiel et n'est pas couvert par la
garantie. Le cordon d'alimentation doit être connecté à une prise de
courant avec mise à la terre.
17
Routing and Arranging Cables
Gen 7E/8E bases feature their own cable management to help you well
organize the cords whenever you need to connect peripheral devices to XT-
5315/5515/5515Pro. The following provides some useful cable-routing
instructions required to manage your cables.
1. Set up your terminal in Full Extended
mode and then tilt the screen all the way
down.
2. Remove the cable cover.
3. Pull outwards the locking levers with your
forefingers and then remove the neck
cover in the direction shown by the arrow.
4. Tilt the screen to the horizontal position.
Thread the cables along the cable passage
and then through the cable exit.
5. Tilt the terminal up enough to have the bottom I/O plate
towards you. Locate the cable arrangement cover as shown in
the figure.
Cable Arrangement Cover
18
6. Remove the cable arrangement cover by
pushing it up in the direction shown by
the arrow.
7. Properly insert the cable into the correct
port on the bottom I/O plate.
8. Neatly arrange your cable. Then, make
sure the cord can be held into place and
passed through the cable exit after sliding
back the cable arrangement cover.
9. Have the screen tilt all the way down, and
then push the neck cover back into place.
10. Place the cable cover back.
11. Make sure the cable is threaded through the cable exit at the bottom
of the base.
Gen 7E base
Gen 8E base
Cable Exit
19
Installing Optional Upgrade Kits and Peripherals
XT-5315/5515/5515Pro is an expandable model which allows you to upgrade
its own capacity by additionally installing multiple peripheral devices, such as
magnetic stripe reader (MSR), LCD monitor and cash drawer, according to
your preference. The following will give you installation instructions on how
to expand on your current POS system with these optional upgrade kits. Before
proceeding with the installation of peripherals, please make sure the POS
system is completely shut down to prevent damage.
Installing UPS Battery to Gen 8E Base
UPS battery compartment can be found at
the bottom of Gen 8E base as shown in the
figure. Please be advised that the installation
of UPS battery should be conducted by a
technician according to the user manual
specific to UPS battery.
Installing PoweredUSB to Gen 8E Base
The middle compartment at the bottom of Gen 8E
base is designed to install PoweredUSB.
However, the installation of PoweredUSB is
required to be conducted properly and accurately,
so please contact your service provider for help.
The detailed installation guide will be provided in
the relevant technical manual.
Installing Power Adapter to Gen 8E Base
Power adapter is used to provide power which your terminal needs to be
operated normally. Please go through the below steps to install the power
adapter into Gen 8E base. If the power adapter is already installed to Gen
8E base, you may skip this section
1. Lay your POS terminal on a flat surface
with its bottom facing towards you.
20
2. Take the AC power adapter with its
rubber feet facing you. Place the bottom
side of the power adapter into the
bottom of the power adapter
compartment first, and then push the top
side of the adaptor into the
compartment.
3. After pushing the power adapter up to
the top, place two brackets separately on
the top and bottom sides of the power
adapter compartment as shown in the
figure. Then, fasten two brackets with
four fixing screws.
4. Before threading the cable through the cable exit, loosen two
fixing screws for the bracket of the PoweredUSB compartment.
Then, slide the bracket in the direction shown by the arrow to
remove the bracket.
5. Pass the cable of the power adapter
through the cable exit and then connect
it to the port on the I/O plate of your
POS system. (Please refer to Routing
and Arranging Cables section to thread
the cable, according to the model of
your base.)
Cable Exit
Bracket Power Adaptor
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Posiflex JIVA XT-5515 Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Posiflex JIVA XT-5515 User manual
Documents connexes
-
Posiflex PS-3216A Manuel utilisateur
-
-
-
-
-
Posiflex XT-6317/6517 Manuel utilisateur
-
Posiflex XT-6315/6315E/6515/6515E Manuel utilisateur
-
-
-