Posiflex PS-3216A Manuel utilisateur

Taper
Manuel utilisateur
1
Package Contents
Fanless LCD touch terminal (x1)
Power adaptor (x1)
Power cord (x1)
User Manual (x1)
The appearance of the product may be somewhat different from that of
the actual product, so the appearance of this product should be based
on that of physical products. The contents in this manual may be
updated at any time without prior notice.
PS-3216A
Fanless LCD Touch Terminal
User Manual
13110903010 Ver. A0
http://www.posiflex.com
2
SOME IMPORTANT NOTES
FCC NOTES
This system meets industry & government requirements and applicable standards.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions manual, may cause
interference to radio communications. It has been tested and found to comply with
limits for a Class A digital device pursuant to subpart B of Part 15 of FCC Rules,
which are designed to provide reasonable protection against interference when
operated in a commercial environment. Operation of this equipment in a residential
area is likely to cause interference in which case the user at his own expense will
be required to take whatever measures to correct the interference.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential
environment this equipment may cause radio interference.
AVERTISSEMENT CE CLASSE A
Cet équipement est conforme à la classe A de CISPR 32. Dans un environnement
sidentiel, cet équipement peut provoquer des interrences radio.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person
other than the authorized technicians. The user should consult his/her dealer for the
problem happening. Warranty voids if the user does not follow the instructions in
application of this merchandise. The manufacturer is by no means responsible for
any damage or hazard caused by improper application.
LIMITES DE GARANTIE
La garantie prend fin automatiquement lorsque la machine est ouverte par une
personne autre que les techniciens autorisés. L'utilisateur doit consulter son
revendeur pour le problème qui se produit. La garantie s'annule si l'utilisateur ne
suit pas les instructions d'application de cette marchandise. Le fabricant n'est en
aucun cas responsable de tout dommage ou danger causé par une mauvaise
application.
警告使用者
這是甲類的資訊產品,在居住的環境中使用時,可能會造成射頻干擾,在
3
種情況下,使用者會被要求採取某些適當的對策。
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to be
present.
CONSIGNES DE SÉCURITÉ
Cet équipement ne convient pas à une utilisation dans des lieux pouvant accueillir
des enfants.
BATTERY CAUTION NOTES
Dispose of used batteries according to the instructions.
Replacement of a battery with an incorrect type that can defeat a safeguard
(for example, in the case of some lithium battery types)
Disposal of a battery into fire or a hot oven, or mechanically crushing or
cutting of a battery that can result in an explosion.
Leaving a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of flammable
liquid or gas.
A battery subjected to extremely low air pressure that may result in an
explosion or the leakage of flammable liquid or gas.
BATTERIE ATTENTION NOTES
Jetez les piles usagées conformément aux instructions.
Remplacement d'une batterie avec un type incorrect qui peut annuler une
sauvegarde (par exemple, dans le cas de certains types de batterie au
lithium)
Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou
écrasement ou coupure mécanique d'une batterie pouvant entraîner une
explosion.
Laisser une batterie dans un environnement environnant à des températures
extrêmement élevées pouvant entraîner une explosion ou la fuite de liquide
ou de gaz inflammable.
Une batterie soumise à une pression atmosphérique extrêmement basse
pouvant provoquer une explosion ou une fuite de liquide ou de gaz
inflammable.
警告
本電池如果更換不正確會有爆炸的危險,請依製造商說明書處理用過之電
池。
4
Terminal from shipping mode to operation mode
In consideration of proper packaging, before shipping, the
terminal is folded, staying in shipping mode. Thus, when
receiving the product, you will find that the terminal is well
folded, as shown below.
Before operating this terminal, unfold it and make this terminal
rise in operation mode by referring to the following steps. Here,
an equivalent model with GEN 7 base is taken below for example.
5
3. Place this terminal on a flat table.
4. Tilt this terminal to a degree in the direction as indicated by
the arrow below.
Terminal from operation mode to shipping mode
To fold this terminal, refer to the following steps. Here, an
equivalent model with GEN 7 base is taken below for example.
1. Remove the cable cover.
2. Carefully hold the lower rim of the display.
6
3. Push the base-folding lever in the direction as indicated by the
arrow below (1). Then, the display will be loosen and go
down (2).
4. When the display goes down to a degree, loose the base-
folding lever, as shown in the direction as indicated by the
arrow below.
5. Then, gently tilt the display in the direction as indicated by
the arrow below until the display is well folded.
1
2
7
6. Put back the cable cover.
Views of the PS-3216A
Front View
Rear View
P-CAP Touch Panel
Gen 7E Base
LED Indicator
Rear I/O Cover
Hinge for LCD
Neck Cover
Cable Cover
Cable Exit
2
nd
Display
Screw Hole
8
Left Side View Right Side View
Bottom View
View of I/O Interface
Top I/O Ports
1
12V DC-OUT Power Jack
(for Second Display)
3
USB 2.0 Port
2
HDMI Port
-
-
The top I/O ports are provided for COM-based and USB-based peripheral
devices, for example, customer display.
MSR Port Cover
Bottom I/O Cover
1
2
Power Button
Brightness
Adjustment Button +
Brightness
Adjustment Button -
3
9
Bottom I/O Ports
1
USB 2.0 Port
2
Micro USB Port
3
Micro SD Card Slot
4
RJ45 LAN Port
5
DB9 Serial COM Port
6
RJ11 Cash Drawer Port
7
12VDC-IN Power Jack
Installing Optional Upgrade Kits and Peripherals
PS-3216A can work with multiple optional upgrade kits and
peripheral devices, such as magnetic stripe reader (MSR), LCD
monitor, cash drawer and the like.
Before installing an optional upgrade kit and/or peripheral device,
make sure that the system is powered off and the external power
source is removed from the POS box to prevent electric hazard!
Failure to follow the warning description will void the product
warranty!
For the detailed instruction, refer to each of the user manuals of
the optional upgrade kits and peripheral devices.
Connecting Power Adapter and I/O Cables
Before connecting power adapter and I/O cables to the I/O ports
of PS series terminal, please route and arranging the cables. Refer
to the following step-by-step instruction of cable routing and
arrangement for the details. Here, an equivalent model with GEN
7 base is taken below for example.
1
2
5
6
7
3
4
10
1. Press the circled section of the
cable cover with your thumb.
2. Pull out the cable cover.
3. Push and tilt the terminal to the
end in the direction as shown by
the arrow. Then determine that the
terminal is tilted to the end, as
shown in the right figure.
Pull out
11
4. Press the circled section with two
thumbs and pull by force the two
sides of the locking hook with
two forefingers as indicated by
the arrow.
5. Remove the neck cover from the
base stand.
6. Tilt the terminal slightly at a little angle in the direction as
shown by the arrow, making cables easily pass through the
cable passage.
7. Make the connector, which will be connected to the I/O port
of the terminal, pass through the cable passage of base stand.
Cable Passage
12
8. Push and tilt the terminal
to the end in the direction
as shown by the arrow.
9. Remove the bottom I/O
cover with your forefinger
inserting the middle hole
of the cover.
10. Connect the connector of
the power adapter to the
12VDC-IN power jack.
11. Cover the bottom I/O interface and gather the I/O cables to
the circled cable arrangement area, as shown below.
13
12. Push and tilt the terminal to the
end in the direction as shown by
the arrow.
13. Arrange well the I/O cable located
at the area of neck cover.
14. Shield the I/O cable arrangement area on the neck of the base
stand with the neck cover.
15. Shield the I/O cable exposure area with the cable cover.
14
CAUTION: On doing insertion or extraction of a cable connector, please
always hold the connector head itself instead of pulling the cable wire.
Doing this could damage the cables and ports, which is considered as an
artificial damage and is not covered by the warranty. The means of power
cord should be connected to a socket-outlet with earthing connection.
ATTENTION: Lors de l'insertion ou de l'extraction d'un connecteur de
câble, veuillez toujours tenir la tête du connecteur elle-même au lieu de
tirer le fil du câble. Cela pourrait endommager les câbles, ce qui est
considé comme un dommage artificiel et n'est pas couvert par la
garantie. Le cordon d'alimentation doit être connecté à une prise de
courant avec mise à la terre.
Powering ON the PS-3216A
After connecting the power cable to the power jack
of the terminal, press the power button to power on
the terminal. To power it off, press the power
button again.
Once powering off the system, if you want to
power it on again, please wait at least 3 seconds.
If the system hangs due to a reason, such as software resource
conflict, please press and hold the power button for over 10
seconds to forcedly shut down the system.
Power LED Indicator
LED status indicator, which is located at the lower right side of
the LCD panel, is mainly responsible for notifying users of the
current system status by emitting various LED signals. The table
provided below shows all the possible LED status as a quick
reference.
LED
Status
Description
POWER
Solid blue
System power ON
Solid orange
System standby
Operation Environment
This terminal must NOT be operated in an environment with
restricted ventilation. There must be at least 25 mm air clearance
around any top or side ventilation holes with free flow of air
15
around the unit at all times for system operation.
Specifications
System
Configuration
Processor
Rockchip RK3399
System
Memory
2GB /4GB DDR4
Storage Device
16GB / 32GB + Micro SD Card Slot x 1
OS support
Android 9.0
Display & Touch
LCD
15.6” TFT LCD 1366 x 768
Touch
PCAP touch panel
I/O & Expansion
Serial Port
2 x DB9 on bottom I/O plate, 5V/12V support by
jumper setting
USB Port
(external port)
5, 4 on bottom I/O plate + 1 on top I/O plate
USB Port
(internal port)
2 x USB 2.0 pin header
USB Port
(OTG)
1 x micro USB
LAN Port
1 x 10 / 100 / 1000 Mb
Display Port
1 x HDMI Port
CR Port
1, control 2 CR via optional Y-cable
Power Jack
1 x 12V DC-IN 4-pin power jack for system power
1 x 12V DC-OUT 2-pin power jack for HDMI
monitor)
Audio
1 x internal 2W speaker
Base Stand
7th generation foldable base stand
Power Supply
12V/40W
Expansion Slot
1 x mini-PCIe slot for WiFi/BT, 1T1R antenna
Mechanical
Dimension
372 x 252.7 x 291.4 (W x D x H in mm)
Weight
4.7 (N.W. in kg)
Environmental
Operating
Condition
C - 40°C, 20%RH - 90%RH
Storage
Condition
-20°C - 70°C, 10%RH - 90%RH
Regulatory
Regulation
Rules
FCC/CE/LVD
The product information and specifications are subject to change without prior
notice. To get the detailed information on the PS-3216A, please check this model
from Posiflex Global Website.
16
<MEMO>
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Posiflex PS-3216A Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues