1
Package Contents
Fanless LCD touch terminal………………………...………………...(x1)
Power adaptor…………………….……………………………...……(x1)
Power cord……………………………………………….....................(x1)
User Manual…………………………………………….......................(x1)
FCC NOTES
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential environment this
equipment may cause radio interference.
AVERTISSEMENT CE CLASSE A
Cet équipement est conforme à la classe A de CISPR 32. Dans un environnement
résidentiel, cet équipement peut provoquer des interférences radio.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other than
the authorized technicians. The user should consult his/her dealer for the problem happening.
Warranty voids if the user does not follow the instructions in application of this merchandise.
The manufacturer is by no means responsible for any damage or hazard caused by improper
application.
LIMITES DE GARANTIE
La garantie prend fin automatiquement lorsque la machine est ouverte par une personne
autre que les techniciens autorisés. L'utilisateur doit consulter son revendeur pour le
problème qui se produit. La garantie s'annule si l'utilisateur ne suit pas les instructions
d'application de cette marchandise. Le fabricant n'est en aucun cas responsable de tout
dommage ou danger causé par une mauvaise application.
PS-3216A-G2
Fanless LCD Touch Terminal
User Manual
13110906010 Ver. A0
2
警告使用者
此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情況
下，使用者會被要求採取某些適當的對策。
SAFETY INSTRUCTIONS
This equipment is not suitable for use in locations where children are likely to be present.
CONSIGNES DE SÉCURITÉ
Cet équipement ne convient pas à une utilisation dans des lieux pouvant accueillir des
enfants.
WARNING
Power cord shall be connected to a socket-outlet with earthing connection.
ATTENTION
Le cordon d'alimentation doit être connecté à une prise de courant avec mise à la terre.
BATTERY WARNING
Risk of explosion if battery is replaced by an incorrect type. Dispose of expended
battery in accordance with local disposal regulations.
AVERTISSEMENT DE BATTERIE
Risque d'explosion si la batterie est remplacée par un type incorrect. Jetez la batterie
usagée conformément aux réglementations locales en matière d'élimination.
警告
本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之電池。
3
Views of the PS-3216A-G2
Front View
Rear View
Left Side View Right Side View
MSR Port Cover
Power Button
Brightness
Adjustment Button “+”
Brightness
Adjustment Button “-”
P-CAP Touch Panel
Gen 7 Base
LED Indicator
Hinge for LCD
Neck Cover
Cable Cover
Cable Exit
2nd Display
Screw Hole
Rear I/O Cover
4
Bottom View
View of I/O Interface
Top I/O Ports
1
12V DC-OUT Power Jack
(for Second Display)
3
USB 2.0 Port
2
HDMI Port
-
-
※
The top I/O ports are provided for COM-based and USB-based peripheral
devices, for example, customer display.
Bottom I/O Ports
1
12VDC-IN Power Jack
2
Cash Drawer Port
3
DB9 Serial COM Port
4
RJ45 LAN Port
5
Micro USB Port
6
Micro SD Card Slot
7
USB 2.0 Ports
Terminal from shipping mode to operation mode
In consideration of proper packaging, before shipping, the terminal is folded,
staying in shipping mode. Thus, when receiving the product, you will find that
the terminal is well folded, as shown below.
1
2
3
1
2
5
6
7
3
4
Bottom I/O Cover
5
Before operating this terminal, unfold it and make this terminal rise in
operation mode by referring to the following steps. Here, an equivalent model
with GEN 7 base is taken below for example.
1. Firstly, lift this terminal gently to make it
to be unfolded.
2. Overturn this terminal in the direction as
indicated by the arrow in the right figure.
3. Place this terminal on a flat table.
4. Tilt this terminal to a degree in the direction as indicated by the arrow
below.
6
5. Remove the cable cover from the base.
6. Fix the base with two #/6/32 screws.
7. Push the cable cover back to the base.
Terminal from operation mode to shipping mode
To fold this terminal, refer to the following steps. Here, an equivalent model
with GEN 7 base is taken below for example.
1. Remove the cable cover.
2. Remove the two screws from the base.
7
3. Carefully hold the lower rim of the display.
4. Push the base-folding lever in the direction as indicated by the arrow
below (1). Then, the display will be loosen and go down (2).
5. When the display goes down to a degree, loose the base-folding lever, as
shown in the direction as indicated by the arrow below.
6. Then, gently tilt the display in the direction as indicated by the arrow
below until the display is well folded.
1
2
8
7. Put back the cable cover.
Installing Optional Upgrade Kits and Peripherals
PS-3216A-G2 can work with multiple optional upgrade kits and peripheral
devices, such as magnetic stripe reader (MSR), LCD monitor, cash drawer and
the like.
Before installing an optional upgrade kit and/or peripheral device, make sure
that the system is powered off and the external power source is removed from
the POS box to prevent electric hazard! Failure to follow the warning
description will void the product warranty!
For the detailed instruction, refer to each of the user manuals of the optional
upgrade kits and peripheral devices.
Connecting Power Adapter and I/O Cables
Before connecting power adapter and I/O cables to the I/O ports of PS series
terminal, please route and arranging the cables. Refer to the following step-by-
step instruction of cable routing and arrangement for the details. Here, an
equivalent model with GEN 7 base is taken below for example.
1. Press the circled section of the cable
cover with your thumb.
9
2. Pull out the cable cover.
3. Push and tilt the terminal to the end in
the direction as shown by the arrow.
Then determine that the terminal is tilted
to the end, as shown in the right figure.
4. Press the circled section with two
thumbs and pull by force the two sides
of the locking hook with two forefingers
as indicated by the arrow.
5. Remove the neck cover from the base
stand.
Pull out
10
6. Tilt the terminal slightly at a little angle in the direction as shown by the
arrow, making cables easily pass through the cable passage.
7. Make the connector, which will be connected to the I/O port of the
terminal, pass through the cable passage of base stand.
8. Push and tilt the terminal to the
end in the direction as shown by
the arrow.
9. Remove the bottom I/O cover
with your forefinger inserting
the middle hole of the cover.
Cable Passage
11
10. Connect the connector of the
power adapter to the 12VDC-IN
power jack.
11. Cover the bottom I/O interface and gather the I/O cables to the circled
cable arrangement area, as shown below.
12. Push and tilt the terminal to the end in the
direction as shown by the arrow.
13. Arrange well the I/O cable located at the
area of neck cover.
12
14. Shield the I/O cable arrangement area on the neck of the base stand with
the neck cover.
15. Shield the I/O cable exposure area with the cable cover.
CAUTION: On doing insertion or extraction of a cable connector, please
always hold the connector head itself instead of pulling the cable wire.
Doing this could damage the cables and ports, which is considered as an
artificial damage and is not covered by the warranty. The means of power
cord should be connected to a socket-outlet with earthing connection.
ATTENTION: Lors de l'insertion ou de l'extraction d'un connecteur de
câble, veuillez toujours tenir la tête du connecteur elle-même au lieu de
tirer le fil du câble. Cela pourrait endommager les câbles, ce qui est
considéré comme un dommage artificiel et n'est pas couvert par la
garantie. Le cordon d'alimentation doit être connecté à une prise de
courant avec mise à la terre.
Powering ON the PS-3216A-G2
After connecting the power cable to the power jack of the
terminal, press the power button to power on the terminal. To
power it off, press the power button again.
Once powering off the system, if you want to power it on
again, please wait at least 3 seconds.
13
If the system hangs due to a reason, such as software resource conflict, please
press and hold the power button for over 10 seconds to forcedly shut down the
system.
Power LED Indicator
LED status indicator, which is located at the lower right side of the LCD panel,
is mainly responsible for notifying users of the current system status by
emitting various LED signals. The table provided below shows all the possible
LED status as a quick reference.
LED
Status
Description
POWER
Solid blue
System power ON
Solid orange
System standby
Operation Environment
This terminal must NOT be operated in an environment with restricted
ventilation. There must be at least 25 mm air clearance around any top or side
ventilation holes with free flow of air around the unit at all times for system
operation.
Specifications
System
Configuration
Processor
Rockchip RK3568
System
Memory
4GB /8GB DDR4
Storage Device
32GB / 64GB + Micro SD Card Slot x 1
OS support
Android 11.0
Display & Touch
LCD
15.6” TFT LCD 1366 x 768
Touch
PCAP touch panel
I/O & Expansion
Serial Port
2 x DB9 on bottom I/O plate, 5V/12V support by
jumper setting
USB Port
(external port)
5, 4 on bottom I/O plate + 1 on top I/O plate
USB Port
(OTG)
1 x micro USB
LAN Port
1 x 10 / 100 / 1000 Mb
Display Port
1 x HDMI Port
CR Port
1, control 2 CR via optional Y-cable
Power Jack
1 x 12V DC-IN 4-pin power jack for system power
1 x 12V DC-OUT 2-pin power jack for HDMI
monitor)
Audio
1 x internal 2W speaker
14
Base Stand
7th generation foldable base stand
Power Supply
12V/40W
Expansion Slot
1 x M.2 slot for WiFi/BT
Mechanical
Dimension
372 x 252.7 x 291.4 (W x D x H in mm)
Weight
4.7 (N.W. in kg)
Environmental
Operating
Condition
0°C - 40°C, 20%RH - 90%RH
Storage
Condition
-20°C - 70°C, 10%RH - 90%RH
Regulatory
Regulation
Rules
FCC/CE/LVD
※
The product information and specifications are subject to change without prior
notice. To get the detailed information on the PS-3216A-G2, please contact your
dealer or the service team
15
<MEMO>
16
<MEMO>
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
dans d''autres langues
- English: Posiflex PS-3216A-G2 User manual
Documents connexes
-
Posiflex PS-3216A Manuel utilisateur
-
-
Posiflex PS-3616Q Manuel utilisateur
-
Posiflex XT-6515E Manuel utilisateur
-
-
Posiflex XT-6317/6517 Manuel utilisateur
-
-
-
-