STIHL FSA 65, 85 Manuel utilisateur

STIHL FSA 65, 85

Instruction Manual

Notice d’emploi

G Instruction Manual

1 - 23

F Notice d’emploi

24 - 48

Original Instruction ManualPrinted on chlorine-free paper

Printing inks contain vegetable oils, paper can be recycled.

0458-284-8221-A. VA3.H19.

0000003590_012_GB

FSA 65, FSA 85

English

1

with electronic systems.

Contents

Dear Customer,

Thank you for choosing a quality

engineered STIHL product.

It has been built using modern

production techniques and

comprehensive quality assurance.

Every effort has been made to ensure

your satisfaction and trouble-free use of

the product.

Please contact your dealer or our sales

company if you have any queries

concerning this product.

Your

Dr. Nikolas Stihl

Guide to Using this Manual 2

Safety Precautions and Working

Techniques 2

Using the Unit 6

Approved Combinations of Cutting

Attachment and Deflector 7

Adjusting the Loop Handle 7

Mounting the Deflector 8

Adjusting Nylon Line 8

Connecting Charger to Power

Supply 9

Charging the Battery 9

LEDs on Battery 10

LED on Charger 12

Switching On 12

Switching Off 13

Storing the Machine 14

Replacing Nylon Line 14

Maintenance and Care 17

Main Parts 18

Specifications 19

Troubleshooting 21

Maintenance and Repairs 23

Battery Recycling 23

Disposal 23

FSA 65, FSA 85

English

2

Pictograms

All the pictograms attached to the

machine are shown and explained in this

manual.

Symbols in text

WARNING

Warning where there is a risk of an

accident or personal injury or serious

damage to property.

NOTICE

Caution where there is a risk of

damaging the machine or its individual

components.

Engineering improvements

STIHL's philosophy is to continually

improve all of its products. For this

reason we may modify the design,

engineering and appearance of our

products periodically.

Therefore, some changes, modifications

and improvements may not be covered

in this manual.

Observe all applicable local safety

regulations, standards and ordinances.

If you have not used this model before:

Have your dealer or other experienced

user show you how it is operated or

attend a special course in its operation.

Minors should never be allowed to use

this product.

Keep bystanders, especially children,

and animals away from the work area.

When the machine is not in use, store it

so that it does not endanger others.

Secure it against unauthorized use.

The user is responsible for avoiding

injury to third parties or damage to their

property.

Do not lend or rent your power tool

without the instruction manual. Be sure

that anyone using it understands the

information contained in this manual.

The use of noise emitting power tools

may be restricted to certain times by

national or local regulations.

To operate this power tool you must be

rested, in good physical condition and

mental health.

If you have any condition that might be

aggravated by strenuous work, check

with your doctor before operating a

power tool.

Do not operate the power tool if you are

under the influence of any substance

(drugs, alcohol) which might impair

vision, dexterity or judgment.

Use your power tool only for cutting

grass, wild growth and similar materials.

Do not use your power tool for any other

purpose because of the increased risk of

accidents.

– before carrying out inspections,

adjustments or cleaning work

– before working on the cutting

attachment

– before leaving the machine

unattended

– before transporting the machine

– before storing the machine

– before performing repairs or

maintenance work

– in the event of danger or in an

emergency

Guide to Using this Manual Safety Precautions and

Working Techniques

Some special safety pre-

cautions have to be

observed when working

with this power tool

because of the very high

speed of the cutting

attachment.

It is important that you

read the instruction man-

ual before first use and

keep it in a safe place for

future reference. Non-

observance of the

instruction manual may

result in serious or even

fatal injury.

Remove the battery from

the power tool:

FSA 65, FSA 85

English

3

This avoids the risk of the motor starting

unintentionally.

Only use cutting attachments and

accessories that are explicitly approved

for this power tool by STIHL or are

technically identical. If you have any

questions in this respect, consult a

servicing dealer. Use only high quality

tools and accessories in order to avoid

the risk of accidents and damage to the

machine.

STIHL recommends the use of genuine

STIHL tools and accessories. They are

specifically designed to match the

product and meet your performance

requirements.

Never attempt to modify your machine in

any way since this may increase the risk

of personal injury. STIHL excludes all

liability for personal injury and damage

to property caused while using

unauthorized attachments.

The deflector on this power tool cannot

protect the operator from all objects

thrown by the cutting attachment

(stones, glass, wire, etc.). Such objects

may ricochet and then hit the operator.

Do not use a pressure washer to clean

your power tool. The solid jet of water

may damage parts of the power tool.

Do not spray the power tool with water.

Battery

Observe the information in the leaflet or

instruction manual supplied with the

STIHL battery and keep it in a safe

place.

For further notes on safety visit

www.stihl.com/safety-data-sheets.

Charger

Observe the information in the leaflet

supplied with the STIHL charger and

keep it in a safe place.

Clothing and Equipment

Wear proper protective clothing and

equipment.

Avoid clothing that could get caught on

branches or brush or moving parts of the

machine. Do not wear a scarf, necktie or

jewelry. Tie up and confine long hair

(e.g. with a hair net, cap, hard hat, etc.).

WARNING

Wear a face shield and make sure it is a

good fit. A face shield alone does not

provide adequate eye protection.

STIHL offers a comprehensive range of

personal protective clothing and

equipment.

Transporting the Power Tool

Always switch off the power tool, move

the retaining latch to ƒ and remove the

battery – even when you carry the

machine for short distances. This avoids

the risk of the motor starting

unintentionally.

Carry the power tool properly balanced

by the shaft.

Transporting by vehicle: Properly secure

the power tool to prevent turnover and

damage.

Clothing must be sturdy

but allow complete free-

dom of movement. Wear

snug-fitting clothing, an

overall and jacket combi-

nation, do not wear a

work coat.

Wear sturdy shoes with

non-slip soles.

To reduce the risk of eye

injuries, wear close-fit-

ting safety glasses in

accordance with Euro-

pean Standard EN 166.

Make sure the safety

glasses are a comforta-

ble and snug fit.

Wear heavy-duty work

gloves made of durable

material (e.g. leather).

3905BA000 KN

FSA 65, FSA 85

English

4

Before Starting Work

Check that your power tool is properly

assembled and in good condition – refer

to appropriate chapters in the instruction

manual.

– The trigger switch and trigger

lockout must move freely (retaining

latch to ‚) – switches must return to

the idle position when they are

released.

– Use only an approved combination

of cutting attachment, deflector and

handle. All parts must be

assembled properly and securely.

To reduce the risk of injury, never

use metal cutting attachments.

– Check that the cutting attachment is

properly and securely mounted and

in good condition.

– Check protective devices (e.g.

deflector for cutting attachment) for

damage or wear. Always replace

damaged parts. Never operate the

unit with a damaged deflector.

– Never attempt to modify the controls

or safety devices in any way.

– Keep the handles dry and clean –

free from oil and dirt – for safe

control of the power tool.

– Check contacts in battery

compartment for foreign matter.

– Fit the battery correctly – it must

engage audibly.

– Never use defective or deformed

batteries.

To reduce the risk of accidents, do not

operate your power tool if it is not

properly assembled and in good

condition.

Before switching on the power tool,

make sure the cutting attachment is not

touching the ground or any other object.

Holding and Controlling the Power Tool

Always hold the power tool firmly with

both hands on the handles. Make sure

you always have good balance and

secure footing.

Right-handers

Left hand on the loop handle and right

hand on the control handle.

Left-handers

Right hand on the loop handle and left

hand on the control handle.

During Operation

In case of imminent danger or in an

emergency, switch off the motor

immediately, move retaining latch to ƒ

and remove the battery.

The cutting attachment may catch and

fling objects a great distance and cause

injury - therefore, do not allow any other

persons within a radius of 15 meters of

your own position. To reduce the risk of

damage to property, also maintain this

distance from other objects (vehicles,

windows). Even maintaining a distance

of 15 meters or more cannot exclude the

potential danger.

This power tool may be used in the rain

and wet. Dry off your power tool after

finishing work.

Do not leave the power tool outdoors in

the rain.

To reduce the risk of

injury, avoid contact with

the cutting attachment.

Note that the cutting

attachment continues to

run for a short period

after the power tool is

switched off – flywheel

effect.

3905BA001 KN

3905BA026 KN

15m (50ft)

FSA 65, FSA 85

English

5

Take special care in slippery conditions

(ice, wet ground, snow) – on slopes or

uneven ground.

Watch out for obstacles: Roots and tree

stumps which could cause you to trip or

stumble.

To reduce the risk of accidents, take a

break in good time to avoid tiredness or

exhaustion.

Work calmly and carefully – in daylight

conditions and only when visibility is

good. Stay alert so as not to endanger

others.

If your power tool is subjected to

unusually high loads for which it was not

designed (e.g. heavy impact or a fall),

always check that it is in good condition

before continuing work – see also

"Before Starting Work". Make sure the

safety devices are working properly. Do

not continue operating your power tool if

it is damaged. In case of doubt, consult

your servicing dealer.

Special care must be taken when

working in difficult, over-grown terrain.

The dust that occurs during operation

may be harmful to health. If dust levels

are very high, wear a suitable respirator.

Before leaving the power tool

unattended: Always switch off the power

tool, set the retaining latch to ƒ and

remove the battery.

Check the cutting attachment at regular

short intervals during operation or

immediately if there is a noticeable

change in cutting behavior:

– Switch off the motor, move the

retaining latch to ƒ and wait for the

cutting attachment to come to a

standstill, remove the battery.

– Check condition and tightness, look

for cracks.

Clean grass and plant residue off the

cutting attachment mounting at regular

intervals – remove any build up of

material from the cutting attachment and

deflector.

To replace the cutting attachment,

switch off the power tool, move the

retaining latch to ƒ and remove the

battery. This avoids the risk of injury

from the motor starting unintentionally.

Never continue using or attempt to

repair damaged or cracked cutting

attachments.

This may cause parts of the cutting

attachment to come off and hit the

operator or bystanders at high speed

and result in serious or fatal injuries.

Use only the deflector with properly

mounted line limiting blade to ensure the

mowing lines are automatically trimmed

to the approved length.

After Finishing Work

Always clean dust and dirt off the power

tool with a cloth – do not use any grease

solvents for this purpose.

Do not spray the mowing head or

deflector with water or immerse them in

water as this may damage the drive

motor and electronic control unit in the

motor housing.

Vibrations

This power tool minimizes the vibrations

transmitted to the operator's hands.

However, the operator should seek

medical advice in the event of suspected

circulatory problems in the hands (e.g.

tingling sensation in the fingers).

Maintenance and Repairs

Always move the retaining latch to ƒ

and remove the battery before carrying

out any repairs or maintenance work on

the power tool. This avoids the risk of

the motor starting unintentionally.

To reduce the risk

of injury from

thrown objects,

never operate the

power tool without

the proper deflec-

tor for the type of

cutting attachment

being used.

Inspect the work area:

Stones, pieces of metal

or other solid objects may

be thrown more than 15

meters and cause per-

sonal injury or damage

the cutting attachment

and property (e.g. parked

vehicles, windows).

FSA 65, FSA 85

English

6

Service the machine regularly. Do not

attempt any maintenance or repair work

not described in the instruction manual.

Have all other work performed by a

servicing dealer.

STIHL recommends that you have

servicing and repair work carried out

exclusively by an authorized STIHL

servicing dealer. STIHL dealers are

regularly given the opportunity to attend

training courses and are supplied with

the necessary technical information.

Only use high-quality replacement parts

in order to avoid the risk of accidents

and damage to the unit. If you have any

questions in this respect, consult a

servicing dealer.

STIHL recommends the use of genuine

STIHL replacement parts. They are

specifically designed to match your

model and meet your performance

requirements.

Never attempt to modify your power tool

in any way since this will increase the

risk of personal injury.

Regularly check the electrical contacts

and ensure that the insulation of the

connecting cord and plug of the charger

is in good condition and shows no sign

of ageing (brittleness).

Electrical components, e.g. connecting

cord of charger, may only be repaired or

replaced by a qualified electrician.

Clean plastic components with a cloth.

Do not use aggressive detergents. They

may damage the plastic.

Check tightness of mounting screws on

safety devices and the cutting

attachment and retighten if necessary.

Clean cooling air inlets in motor housing

as necessary.

Keep the battery guides free from

foreign matter – clean as necessary.

Store the power tool in a dry, locked

location with the retaining latch on ƒ

and the battery removed.

Mowing

N Hold the unit with both hands – one

hand on the control handle – one

hand on the loop handle.

N Stand upright – hold the power tool

in a relaxed position.

N Make sure the cutting attachment is

not touching the ground or any other

objects.

N Swing the trimmer back and forth in

an arc.

N The cutting height is determined by

the distance of the mowing line from

the lawn surface.

N Avoid contact with fences, walls,

rocks, etc. since it will result in a

higher rate of wear.

Using the Unit

3905BA002 KN

FSA 65, FSA 85

English

7

Working with bump guard

The bump guard comes standard with

the FSA 85. It is available as a special

accessory for the FSA 65.

The bump guard (1)

– Limits the cutting range of the

mowing line

– reduces the risk of the rotating

mowing line causing damage (e.g.

tree bark)

WARNING

The mowing head may continue to

rotate briefly after you switch off your

power tool – wait for the mowing head to

come to a standstill before adjusting the

bump guard – do not adjust it with your

foot.

Disposal

N Do not throw cuttings into the

garbage can – they can be

composted.

Cutting Attachment

The trimmer comes standard with an

AutoCut C 4-2 mowing head. For safety

reasons no other cutting attachments

may be mounted to the trimmer.

For mounting procedure see chapter on

“Replacing Nylon Line”.

Deflector

The trimmer is supplied with a deflector.

Only this deflector may be mounted to

the trimmer – no other deflectors are

permitted. For further information see

"Mounting the Deflector".

Your new power tool comes with the

loop handle mounted on the drive tube,

but it must be turned and lined up to suit

your requirements.

N Loosen the star knob (1) on the

handle.

N Turn the handle to the vertical

position.

1

3905BA003 KN

Approved Combinations of

Cutting Attachment and

Deflector

3905BA004 KN

Adjusting the Loop Handle

1

3905BA005 KN

3905BA006 KN

FSA 65, FSA 85

English

8

The loop handle can be adjusted to suit

the height and reach of the operator and

the application by changing

distance (A).

Recommendation: distance (A):

about 10 cm

N Slide the handle to the required

position.

N Tighten down the star knob so that

the handle cannot be rotated on the

shaft.

N Position your trimmer so that the

mowing head (1) faces up.

The motor housing has guide slots

(arrows) to correctly locate the deflector.

N Push the deflector (2) into the guide

slots as far as stop.

N Insert the screws (3) and tighten

them down firmly.

Adjusting Nylon Line

N Hold the rotating mowing head

above the ground – tap it on the

ground once – about 3 cm fresh line

is advanced.

The blade (1) on the deflector (2) trims

surplus line to the correct length – avoid

tapping the mowing head more than

once at a time.

Line feed operates only if both lines still

have a minimum length of 2.5 cm.

If the line is shorter than 2.5 cm:

N Switch off the trimmer.

N Move the retaining latch to ƒ and

remove the battery.

N Turn the trimmer on its back.

N Press down the cap on the spool as

far as stop.

N Pull the ends of the lines out of the

spool.

If the spool is empty, see "Replacing

Nylon Line".

3905BA007 KN

A

Mounting the Deflector

1

3905BA008 KN

3

2

3

3905BA009 KN

Adjusting Nylon Line

1

2

3905BA010 KN

FSA 65, FSA 85

English

9

Power supply (mains) voltage and

operating voltage must be the same.

N Insert the plug (1) in the wall

outlet (2).

A self test is performed after the charger

is connected to the power supply. During

this process, the light emitting diode (1)

on the charger lights up green for about

1 second, then red and goes off again.

A factory-new battery is not fully

charged.

Recommendation: Fully charge the

battery before using it for the first time.

N Connect the charger to the power

supply – mains voltage and

operating voltage of the charger

must be the same – see

"Connecting Charger to Power

Supply".

Operate the charger only in enclosed

and dry rooms at ambient temperatures

between +5°C to +40°C (+41°F to

+104°F)

Only charge dry batteries. Allow a damp

battery to dry before charging.

N Push the battery (1) into the

charger (2) until noticeable

resistance is felt – then push it as far

as stop.

The LED (3) on the charger comes on

when the battery is inserted – see "LED

on Charger"

Charging begins as soon as the

LEDs (4) on the battery glow green –

see "LEDs on Battery".

The charge time is dependent on a

number of factors, including battery

condition, ambient temperature, etc.,

and may therefore vary from the times

specified.

The battery heats up during operation in

the power tool. If a hot battery is inserted

in the charger, it may be necessary to

cool it down before charging. The

charging process begins only after the

battery has cooled down. The time

required for cooling may prolong the

charge time.

The battery and charger heat up during

the charging process.

AL 300, AL 500 Chargers

The AL 300 and AL 500 chargers are

equipped with a battery cooling fan

Connecting Charger to

Power Supply

3901BA015 KN

2

1

3901BA019 KN

Charging the Battery

2

3901BA009 KN

4

3901BA014 KN

3

FSA 65, FSA 85

English

10

AL 100 Charger

The AL 100 charger has no fan and

waits for the battery to cool down before

starting the charging process. The

battery is cooled by heat transfer to the

ambient air.

End of Charge

The charger switches itself off

automatically when the battery is fully

charged:

– LEDs on the battery go off.

– The LED on the charger goes off.

– The charger's fan is switched off (if

charger is so equipped)

Remove the fully charged battery from

the charger.

Four LEDs show the battery's state of

charge and any problems that occur in

the battery or machine.

N Press button (1) to activate the

display – the display goes off

automatically after 5 seconds.

The LEDs can glow or flash green or

red.

During charging

The LEDs glow continuously or flash to

indicate the progress of charge.

A green flashing LED indicates the

capacity that is currently being charged.

The LEDs on the battery go off

automatically when the charge process

is completed.

If the LEDs on the battery flash or glow

red – see "If the red LEDs glow

continuously / flash".

LEDs on Battery

LED glows continuously green.

LED flashes green.

LED glows continuously red.

LED flashes red.

1

3901BA010 KN

3901BA018 KN

80 - 100 %

60 - 80 %

40 - 60 %

20 - 40 %

0 - 20 %

FSA 65, FSA 85

English

11

During Operation

N Press button (1) to activate the

display – the display goes off

automatically after 5 seconds.

The green LEDs glow continuously or

flash to indicate the state of charge.

If the LEDs on the battery flash or glow

red – see "If the red LEDs glow

continuously / flash".

If the red LEDs glow continuously / flash

1

3901BA010 KN

3901BA016 KN

80 - 100 %

60 - 80 %

40 - 60 %

20 - 40 %

0 - 20 %

A 1 LED glows

continuously

red:

Battery is too hot

1) 2)

/cold

1)

When charging: Charge process

starts automatically after the battery

has cooled down / warmed up.

2)

During operation: Machine cuts out

– allow battery to cool down; it may

be necessary to take the battery out

of the machine for this purpose.

B 4 LEDs flash

red

Malfunction in

battery

3)

C 3 LEDs glow

continuously

red:

Machine is too hot

– allow it to cool

down.

D 3 LEDs flash

red

Malfunction in

machine

4)

3901BA041 KN

A

B

C

D

3)

Electromagnetic problem or fault.

Take the battery out of the machine

tool and refit it. Switch on the

machine – if the LEDs continue to

flash, the battery is faulty and must

be replaced.

4)

Electromagnetic problem or fault.

Take the battery out of the

machine. Use a blunt tool to

remove dirt from the contacts in the

battery compartment. Refit the

battery. Switch on the machine – if

the light emitting diodes still flash,

the machine is faulty and must be

checked by a servicing dealer –

STIHL recommends an authorized

STIHL servicing dealer.

FSA 65, FSA 85

English

12

The LED (1) on the charger may glow

continuously green or flash red.

Green continuous light ...

... indicates the following:

The battery

– is being charged

– is too hot and must cool down

before charging

See also "LEDs on battery".

The green LED on the charger goes off

as soon as the battery is fully charged.

Red flashing light ...

... may indicate the following:

– No electrical contact between

battery and charger – remove and

refit the battery

– Malfunction in battery – see also

"LEDs on Battery".

– Malfunction in charger – have

checked by a servicing dealer.

STIHL recommends an authorized

STIHL servicing dealer.

A factory-new battery is not fully

charged.

Recommendation: Fully charge the

battery before using it for the first time.

N If necessary, remove the cover from

the battery compartment before

fitting the battery, i.e. depress both

locking tabs to unlock and remove

the cover.

Fitting the Battery

N Insert the battery (1) in the power

tool – the battery slides into the

compartment – press it down

carefully until it snaps into position –

the battery must be flush with the

top of the housing.

Switching on the Machine

N Make sure you have a secure and

firm footing.

N Stand upright – hold the power tool

in a relaxed position.

N Make sure the cutting attachment is

not touching the ground or any other

objects.

N Hold the power tool with both hands

– one hand on the control handle –

one hand on the loop handle.

N Unlock the power tool by moving the

retaining latch (2) to ‚.

N Push down the trigger switch

lockout (3) and depress the trigger

switch (4) and hold them in that

position.

The motor runs only if the retaining

latch (2) is on ‚ and the trigger switch

lockout (3) and trigger switch (4) are

operated simultaneously.

LED on Charger

1

3901BA019 KN

Switching On

1

3905BA011 KN

2

3905BA012 KN

4

3

2

3905BA013 KN

FSA 65, FSA 85

English

13

Trigger

Motor speed can be controlled with the

trigger switch. Motor speed is increased

progressively by squeezing the trigger

switch (FSA 85 only).

N Release the trigger switch

lockout (1) and the trigger

switch (2).

N Move the retaining latch (3) to ƒ –

the trigger switch (2) cannot be

operated – the power tool is locked

to prevent start-up.

Always remove the battery from the

power tool during work breaks and after

finishing work.

Removing the battery

N Press in both locking tabs (4) at the

same time to unlock the battery (5).

N Take the battery (5) out of the

housing.

When the power tool is not in use, shut it

off so that it does not endanger others.

Secure it against unauthorized use.

Switching Off

2

1

3905BA014 KN

3

3905BA015 KN

2

4

3905BA016 KN

FSA 65, FSA 85

English

14

N Move the retaining latch to ƒ.

N Remove the battery.

N Thoroughly clean the machine.

N Store the machine in a dry and

secure location out of the reach of

children and other unauthorized

persons.

Cover for Battery Compartment

In some markets the machine comes

with a cover for the battery

compartment. It protects the battery

compartment from contamination.

N After finishing work, slide the

cover (1) home until it engages

audibly in position.

Storing the Battery

N Take the battery out of the power

tool or the charger.

N Store indoors in a dry and safe

location. Keep out of the reach of

children and other unauthorized

persons and protected from

contamination.

N Do not store spare batteries unused

– use in rotation.

To optimize the life of the battery, store

it at a state of charge of about 30%.

Storing the Charger

N Remove the battery.

N Disconnect the plug from the wall

outlet.

N Store the charger indoors in a dry

and secure location. Keep out of the

reach of children and other

unauthorized persons and

protected from contamination.

STIHL AutoCut C 4-2

Always check the mowing head for signs

of wear before replacing the nylon line.

WARNING

If there are signs of serious wear,

replace the complete mowing head.

Preparations

N Switch off the trimmer.

N Move the retaining latch to ƒ.

N Remove the battery

N Put the power tool on the ground

with the mowing head facing up.

Removing the mowing head and

remaining nylon line

In normal operation, the supply of nylon

line in the head is used up almost

completely.

Storing the Machine

3905BA027 KN

1

Replacing Nylon Line

FSA 65, FSA 85

English

15

N Hold the mowing head steady and

rotate the cap (1) counterclockwise

until it can be removed.

N Remove the mowing head.

N Pull the spool (2) out of the mowing

head (3) and remove the remaining

line.

Assembling the mowing head

N Fit the empty spool in the mowing

head (3).

If the spring (4) has popped out:

N Push the spring into the spool (2) as

far as stop.

Winding line onto spool

N Use green-coded nylon line with a

diameter of 2.0 mm.

N Cut two 2.5 m lengths of line from

the replacement reel (special

accessory).

N Rotate the spool (2)

counterclockwise until the two arrow

points are in alignment.

N Push the straight end of each line

through one sleeve (5) in the

mowing head (3) until you feel a

noticeable resistance – and then

continue pushing as far as stop.

3905BA017 KN

2

3

1

3905BA018 KN

2

3

4

3

5

3905BA019 KN

3

FSA 65, FSA 85

English

16

N Hold the mowing head steady.

N Rotate the spool counterclockwise

until the shortest line is about

10 cm.

N If necessary, cut the longer line to a

length of about 10 cm.

The mowing head is now full.

Mounting the Mowing Head

N Slip the mowing head (6) over the

shaft (7) and engage hex recess (8)

on the external hexagon (9).

N Turn the spool (2) clockwise until

the two arrow heads line up –

secure the spool in this position.

N Insert the cap (1) in the spool (2),

press it down as far as stop and turn

it clockwise at the same time.

N Turn the cap (1) as far as stop and

tighten it down by hand.

3905BA020 KN

8

6

9

3905BA021 KN

7

1

2

3905BA022 KN

FSA 65, FSA 85

English

17

Maintenance and Care

The following intervals apply to normal operating conditions only. If your daily work-

ing time is longer or operating conditions are difficult (very dusty work area, etc.),

shorten the specified intervals accordingly.

Move the retaining latch to

ƒ before performing any work on the power tool.

before starting work

after finishing work or daily

weekly

monthly

every 12 months

if problem

if damaged

if required

Complete machine

Visual inspection (condition) X

Clean X

Controls (retaining latch, trigger switch

lockout, trigger switch)

Check operation X

Clean XX

All accessible screws and nuts Retighten X

Battery Visual inspection XXX

Battery compartment

Clean X X

Check operation (eject battery) X

Cutting attachment (mowing head)

Visual inspection X

Replace X

Check tightness X

Safety labels Replace X

FSA 65, FSA 85

English

18

1 Battery Compartment

2 Control Handle

3 Trigger Switch Lockout

4 Trigger Switch

5 Retaining Latch

6 Loop Handle

7 Wing Screw

8 Drive Tube

9 Battery Locking Tabs

10 Battery

11 Light Emitting Diodes (LED) on

Battery

12 Push Button

13 Mowing Head

14 Line Limiting Blade

15 Deflector

16 Charger

17 Light Emiting Diode (LED) on

Charger

18 Power Supply Cord

# Serial Number

Main Parts

14

15

#

18

5

4

3

17

16

3905BA023 KN

1

2

6

7

8

9

10

9

12

11

13

La page charge ...

STIHL FSA 65, 85 Manuel utilisateur

STIHL FSA 65, 85 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents