Sherwood RD-606I Mode d'emploi

Marque: Sherwood

Modèle: RD-606I

Taper: Mode d'emploi

RD-606i

NETWORK AV RECEIVER

OPERATING INSTRUCTIONS

RED RECEPTEUR AV

RESEAU RECEPTOR DE AV

606i(A)_3lan_cover.qxp 2011-05-04 오후 2:14 페이지 1

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.

Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other.

A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit

into your outlet, consult an electrician for replacement of

the obsolete outlet.

10. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the

apparatus.

When a cart is used, use caution when moving the

cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

PORTABLE CART WARNING

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 2

ENGLISH

FOR YOUR SAFETY

CAUTION

Introduction

: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This symbol is intended to alert the user to the presence of

uninsulated "dangerous voltage" within the product's

enclosure that may be of sufficient magnitude to constitute

a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

Caution regarding installation

Note : For heat dispersal, do not install this unit in a confined space such as a bookcase or similar enclosure.

Be sure to leave a space around this unit equal to, or greater than, shown below.

Left, right and rear sides : 20 cm, top side : 40 cm.

: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

CAUTION

WARNING

Do not block ventilation openings or stack other equipment on the top.

READ THIS BEFORE OPERATING YOUR UNIT

Note to CATV System Installer :

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be

connected to the grounding system of the building, as

close to the point of cable entry as practical.

FCC INFORMATION

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee

that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which can

be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

Caution : Any changes or modifications in construction

of this device which are not expressly

approved by the party responsible for

compliance could void the user’s authority to

operate the equipment.

This Class B digital apparatus complies with Canadian

ICES-003.

Cet appareil numérique de la Classe B est conforme à

la norme NMB-003 du Canada.

Units shipped to the U.S.A and CANADA are designed for

operation on 120 V AC only.

Safety precaution with use of a polarized AC plug.

However, some products may be supplied with a nonpolarized plug.

U.S.A

CANADA

120 V

• Leave a space around the unit for sufficient ventilation.

• Avoid installation in extremely hot or cold locations, or in an area

that is exposed to direct sunlight or heating equipment.

• Keep the unit free from moisture, water, and dust.

• Do not let foreign objects in the unit.

• The ventilation should not be impeded by covering the ventilation

openings with items, such as newspapers, table-cloths, curtains, etc.

• No naked flame sources, such as lighted candles, should be

placed on the unit.

• Please be care the environmental aspects of battery disposal.

• The unit shall not be exposed to dripping or splashing for use.

• No objects filled with liquids, such as vases, shall be placed on

the unit.

• Do not let insecticides, benzene, and thinner come in contact with

the set.

• Never disassemble or modify the unit in any way.

■Notes on the AC power cord and the wall outlet.

• The unit is not disconnected from the AC power source(mains) as

long as it is connected to the wall outlet, even if the unit has been

turned off.

• To completely disconnect this product from the mains, disconnect

the plug from the wall socket outlet.

• When setting up this product, make sure that the AC outlet you

are using is easily accessible.

• Disconnect the plug from the wall outlet when not using the unit

for long periods of time.

: To prevent electric shock, match wide blade of

plug to wide slot, fully insert.

: Pour éviter chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante

de la prise et pousser jusqu’ au fond.

CAUTION

ATTENTION

ON / STANDBY AUTO / MANUAL SURROUND STEREO VIDEO AUDIO

SOUND INPUT

AUDIO ASSIGNSPEAKER

ON / OFF

TONE CH.LEVEL SETUP ENTER / MEMO BANDPRESETTUNE

PHONES AUX 1 AUX 2

POWER

NETWORK AVRECEIVER RD-606i

USB

5V 1A

RETURN MAIN MENU

MASTER VOLUME

Bluetooth IN

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 3

ENGLISH

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS | 2

Introduction

• READ THIS BEFORE OPERATING YOUR UNIT | 3

System Connections | 5

Front Panel Controls | 11

Remote Controls | 13

• REMOTE CONTROL OPERATION RANGE | 14

• LOADING BATTERIES | 14

Operations

• LISTENING TO A PROGRAM SOURCE | 15

• SURROUND SOUND | 17

• ENJOYING SURROUND SOUND | 18

• LISTENING TO RADIO BROADCASTS | 23

• LISTENING TO INTERNET RADIO BROADCASTS, MUSIC FILES | 25

• RECORDING | 33

• OTHER FUNCTIONS | 34

• CONFIRMING THE HDMI FUNCTION | 35

System Setup | 36

• SETTING THE SYSTEM SETUP | 38

• SETTING THE INPUT SETUP | 40

• SETTING THE SPEAKER SETUP | 41

• SETTING THE CH LEVEL SETUP | 45

• SETTING THE PARAMETER SETUP | 47

• SETTING THE HDMI SETUP | 49

Troubleshooting Guide | 51

Specifications | 52

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 4

ENGLISH

System Connections

• Please be certain that this unit is unplugged from the AC outlet before making any connections.

• Since different components often have different terminal names, carefully read the operating instructions of the component

connected.

• Be sure to observe the color coding when connecting audio, video and speaker cords.

• Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver.

SN.

POWER SOURCE

POWER CONSUMPTION

RD-606i

120V 60Hz

2.3 A

DESIGNED IN USA

MADE IN CHINA

HDMI

VIDEO 2

VIDEO 1

MONITOR

OUT

DIGITAL IN

VIDEO 2

IN OUT

MONITOR

OUT

VIDEO 1VIDEO 1

VIDEO

ANTENNAAUDIO

FM 75

GND

LOOP

COAX 2

(CD)

OPT

(VIDEO 1)

AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.

WARNING : SHOCK HAZARD-DO NOT OPEN.

VIDEO 1 VIDEO 2 CD

VIDEO 1 TAPETAPE

OUT

SUBWOOFER

OUT

COAX 1

(VIDEO 2)NETWORK AV RECEIVER

LAN / ETHERNET

SPEAKERS Class 2 Wiring

SURROUND

(6 ) CENTER

(6 )

FRONT

(6 )

E308916 48W3

Audio/Video

Apparatus

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions : (1)This device may not cause harmful interference, and (2)This device must accept any

interference received, including interference that may cause undesired operation.

Manufactured under license under U.S. Patent #’s: 5,451,942 5,956,674 5,974,380 5,978,762 6,487,535 &

other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks &

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are

trademarks of Dolby Laboratories.

942,3 3

23 1 27

568

1. CONNECTING ANTENNAS

ANTENNA

FM 75

GND

LOOP

ANTENNA

FM 75

GND

LOOP

• Change the position of the FM indoor antenna until you get

the best reception of your favorite FM stations.

ANTENNA

FM 75

GND

LOOP

• Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC

input cord and set it to a direction for the best reception.

• If the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of

the AM loop antenna.

• A 75Ω outdoor FM antenna may be used to further

improve the reception. Disconnect the indoor

antenna before replacing it with the outdoor one.

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 5

ENGLISH

HDMI

VIDEO 2

VIDEO 1

MONITOR

OUT

VIDEO 2

IN OUT

MONITOR

OUT

VIDEO 1VIDEO 1

VIDEO

AUDIO

VIDEO 1 VIDEO 2

VIDEO 1

2. CONNECTING VIDEO COMPONENTS

• The jacks of VIDEO 1 may also be connected to a DVD recorder or other digital video recording component.

For details, refer to the operating instructions of the component to be connected.

• The jacks of VIDEO 2 can also be connected to an additional video component such as a cable TV tuner or satellite system.

• There are (composite) VIDEO jacks for analog video connections and the HDMI connectors for digital video and audio

connections.

• For your reference, the excellence in picture quality is as follows : "HDMI” > "(composite) VIDEO".

■Notes :

• When recording video program sources through the (composite) VIDEO 1 OUT jack or viewing video program sources

through the (composite) MONITOR OUT jack, you must connect the (composite) VIDEO IN jack to the video playback

components such as BD player, DVD player, etc.

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 6

ENGLISH

■HDMI (High Definition Multimedia Interface) connection : (*)

• You can connect the source component (DVD player, etc.) to the display component (TV, projector, etc.) through this receiver

with using a commercially available HDMI cord.

• The HDMI connection can carry uncompressed digital video signals and digital audio signals.

• The HDMI video stream signals (video signals) are theoretically compatible with DVI-D. When connecting to a TV monitor,

etc., equipped with DVI-D connector, it is possible to connect using a commercially available HDMI-DVI converter cord.

Since the HDMI-to-DVI connection cannot carry any audio signals, set the HDMI AUDIO OUT to AMP to hear the HDMI digital

audio signals on this receiver.(For details, refer to "When selecting the HDMI AUDIO OUT" on page 49.)

■Copyright protection system

• This unit supports HDCP (High-bandwidth Digital Contents Protection), technology to protect copyright of digital video signals

against illegal duplication. HDCP must also be supported on the components connected to this unit.

• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing

LLC.

■Notes :

• For stable signal transfer, we recommend using HDMI cables that are a maximum of 5 meters in length.

• Among the components that support HDMI, some components can control other components via the HDMI connector.

For details on the HDMI function, refer to “CONFIRMING THE HDMI FUNCTION” on page 35 and “SETTING THE HDMI

SETUP” on page 49.

• The audio signals from the HDMI connector (including the sampling frequency and bit length) may be limited by the

component that is connected.

• The video signals will not be output properly if a component incompatible with HDCP is connected.

• If the resolutions of the video signals which are output from the MONITOR OUTs and your monitor TV are not matched, the

picture is not clear, natural or displayed. In this case, change the setting of the resolution on the source component (BD

player, etc.) to one which the monitor TV can handle. (For details, refer to the operating instructions of the source component.)

• When you want to enjoy only the picture on your TV, not the sound, you should set the HDMI AUDIO OUT to AMP not to

output the digital audio signal from the HDMI MONITOR OUT of this receiver. (For details, refer to "When selecting the HDMI

AUDIO OUT" on page 49.)

AUDIO

VIDEO 1 TAPETAPE

OUT TAPE Tape deck, MD recorder, etc.

AUDIO

OUT

HDMI OUT AUDIO

CD player, BD player, Video game player, etc.

3. CONNECTING AUDIO COMPONENTS

• The TAPE IN/OUT jacks can be connected to audio recording equipment such as a tape deck, an MD recorder, etc.

• The HDMI IN of CD can be connected to an additional video component without analog video jacks.

Continued

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 7

ENGLISH

5. CONNECTING SUBWOOFER PREOUT

• To emphasize the deep bass sounds, connect a powered

subwoofer.

SUBWOOFER

OUT

4. CONNECTING DIGITAL INS

• The OPTICAL and the COAXIAL DIGITAL OUTs of the

components that are connected to CD, VIDEO 1 and VIDEO 2 of

this unit can be connected to these DIGITAL INs.

• A digital input should be connected to the components such as a

CD player, DVD player, etc. capable of outputting DTS Digital

Surround, Dolby Digital or PCM format digital signals, etc.

• For details, refer to the operating instructions of the component

connected.

• When making the COAXIAL DIGITAL connection, be sure to use

a 75Ω COAXIAL cord, not a conventional AUDIO cord.

• Some of the commercially available optical fiber cords cannot be

used for the equipment. If there is an optical fiber cord which

cannot be connected to your equipment, consult your dealer or

nearest service organization.

■Note :

• Be sure to make either a OPTICAL or a COAXIAL DIGITAL

connection on each component. (You don’t need to do both.)

■Digital input default settings

• If you connect the DIGITAL INs to your components, it is easier to do so following the default settings.

• If your DIGITAL connections are different from default settings, you should assign the DIGITAL INs you used with the “When

selecting the DIGITAL IN” procedure on page 40.

• The default settings are as follows :

OPTICAL IN : VIDEO 1, COAX 1 IN : VIDEO 2, COAX 2 IN : CD

DIGITAL IN

COAX 2

(CD)

OPT

(VIDEO 1)

COAX 1

(VIDEO 2)

• To connect this unit to a broadband home network to listen to internet radio broadcast, connect the LAN/ETHERNET

connector of this unit to your router with a Ethernet cable (CAT-5 or greater recommended).

■Notes :

• After making a broadband internet connection, you should set the communication settings.

(For details, see “When selecting “Network”” on page 31.)

• When using a broadband internet connection, a contract with an internet service provider is required.

For more information, contact your nearest internet service provider.

• Refer to the operating instructions of the equipment because the connected equipment and connection method may differ

depending on your internet environment.

• Use a Ethernet cable/router supporting 10 BASE-T/100 BASE-TX.

• Some Ethernet cables are easily affected by noise. We recommend using a sheilded type cable.

6.CONNECTING TO NETWORK

LAN / ETHERNET

LAN

Internet Modem PCBroadband router

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 8

ENGLISH

7. CONNECTING SPEAKERS

SPEAKERS Class 2 Wiring

SURROUND

(6 ) CENTER

(6 )

FRONT

(6 )

• Be sure to connect speakers firmly and correctly

according to the channel(left and right) and the

polarity (+ and -). If the connections are faulty,

no sound will be heard from the speakers, and if

the polarity of the speaker connection is

incorrect, the sound will be unnatural and lack

bass.

• For installing the speakers, refer to "Speaker

placement" on page 10.

• After installing the speakers, first adjust the

speaker settings according to your environment

and speaker layout.

(For details, refer to "SETTING THE SPEAKER

SETUP" on page 41.)

Caution :

• Be sure to use the speakers with the impedance

of 6 ohms or above.

• Do not let the bare speaker wires touch each

other or any metal part of this unit. This could

damage this unit and/or the speakers.

• Never touch the speaker terminals while the AC

input cord is connected to the wall AC outlet.

Doing so could result in electric shocks.

9. TERMINAL FOR UPGRADES

• This terminal may be used in the future to update the operating software so that it will be able to support new digital audio

formats, etc.

■Note :

• Programming for upgrades requires specialized programming knowledge and for that reason we recommend that it only be

done by qualified installers.

8. AC INPUT CORD

• Plug the cord into a wall AC outlet.

■Connecting speaker wire

1. Strip away approx. 10 mm

(3/8 inch) of wire

insulation, then twist the

wire ends tight.

2. Push the terminal lever,

then keep this condition.

3. Insert the bare part of

the wire into the hole.

4. Put the terminal lever

back, then make sure

it is fastened securely

by pulling the wire

lightly.

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 9

ENGLISH

Ideal speaker placement varies depending on the size of

your room and the wall coverings, etc. The typical example

of speaker placement and recommendations are as follows :

■Front left and right speakers and center speaker

• Place the front speakers with their front surfaces as flush

with TV or monitor screen as possible.

• Place the center speaker between the front left and right

speakers and no further from the listening position than the

front speakers.

• Place each speaker so that sound is aimed at the location

of the listener’s ears when at the main listening position.

■Surround left and right speakers

• Place the surround speakers approximately 1 meter (40

inches) above the ear level of a seated listener on the

direct left and right of them or slightly behind.

■Subwoofer

• The subwoofer reproduces powerful deep bass sounds.

Place a subwoofer anywhere in the front as desired.

■Notes :

• When using a conventional TV, to avoid interference with

the TV picture, use only magnetically shielded front left

and right and center speakers.

• To obtain the best surround effects, the speakers except

the subwoofer should be full range speakers.

Speaker placement

1. TV or Screen

2. Front left speaker

3. Front right speaker

4. Center speaker

5. Subwoofer

6. Surround left speaker

7. Surround right speaker

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 10

ENGLISH

Front Panel Controls

ON / STANDBY AUTO / MANUAL SURROUND STEREO VIDEO AUDIO

SOUND INPUT

AUDIO ASSIGNSPEAKER

ON / OFF

TONE CH.LEVEL SETUP ENTER / MEMO BANDPRESETTUNE

PHONES AUX 1 AUX 2

POWER

STANDBY

NETWORK AV RECEIVER RD-606i

USB

5V 1A

RETURN MAIN MENU

MASTER VOLUME

Bluetooth IN

681 2

910 12 1413 15 16 17 18 19 20 21 22 24

73 4 11 5

■FLUORESCENT DISPLAY

12 3456789

1. Input, frequency, volume level, surround mode,

operating information, etc.

2. Surround mode indicators

3. AUTO indicator

4. DIGITAL INPUT indicator

5. HDMI indicator

6. DIRECT indicator

7. REPEAT indicator

8. SUFFLE indicator

9. SLEEP indicator

1. POWER switch

2. STANDBY indicator

3. POWER ON/STANDBY button

4. REMOTE SENSOR

5. FLUORESCENT DISPLAY

For details, see below.

6. VIDEO INPUT SELECTOR button

7. AUDIO INPUT SELECTOR button

8. MASTER VOLUME knob

9. HEADPHONE jack

10. AUX 1, 2 IN jacks

For details, see next page.

11. AUTO/MANUAL button

12. SURROUND MODE SELECT(▶/◀) buttons

13. STEREO button

14. SPEAKER button

15. AUDIO ASSIGN button

16. TONE MODE button

17. CHANNEL LEVEL button

18. SETUP button

19. ENTER/MEMORY button

20. TUNING UP/DOWN(+/-),

CURSOR LEFT/RIGHT(◀/▶) buttons

21. PRESET UP/DOWN(+/-),

CURSOR UP/DOWN(▲/▼) buttons

22. BAND button

23. USB connector

For details, see next page.

24. Bluetooth IN connector

For details, see next page.

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 11

ENGLISH

AUX 1 AUX 2

• The AUX 1, 2 IN jacks can be connected to additional audio components such as an MP3 player, etc.

■Note :

• When connecting these jacks to an MP3 player, etc., you should use the stereo mini cord, not a mono mini cord.

■AUX 1, 2 IN JACKS

USB

5V 1A Bluetooth IN

• An USB memory device can be connected to the USB connector to

listen to MP3 or WMA files stored on it through this unit. (For details,

refer to “When selecting “USB”” on page 29.)

■Note :

• After USB playback, remove the USB memory device in the stop mode

or the standby mode.

■USB CONNETOR

USB memory device

■Bluetooth IN CONNECTOR

USB

5V 1A Bluetooth IN

• If the Bluetooth IN connector is connected to Sherwood Audio Receiver

BT-R7(sold separately) with Bluetooth wireless technology, you can enjoy

music wirelessly with a music player featuring Bluetooth wireless

technology such as MP3 player, mobile phone, etc..

(For information on Sherwood Audio Receiver BT-R7, contact your dealer.)

• The Bluetooth word mark and logos are registered trademarks owned by

Bluetooth SIG, Inc. and any use of such marks by Sherwood Corporation is

under license. Other trademarks and trade names are those of their

respective owners.

■Note:

• For safe operation, turn the power off before connecting or disconnecting

the Audio Receiver BT-R7.

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 12

ENGLISH

Remote Controls

NETWORK CONTROL (NETWORK,

PAUSE( ), PLAY( ), STOP( ),

REPEAT( ), SHUFFLE( ),

BACKWARD SKIP( ),

FORWARD SKIP( )) buttons

SURROUND MODE

SELECT (>/<) buttons

CURSOR CONTROL( , , , ), ENTER

</SEARCH MODE, SELECT / > buttons

The functions in “< >” are regional option

for Europe, etc.

■Note :

• The RATING( ) button is not available for this receiver.

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 13

ENGLISH

ON / STANDBY AUTO / MANUAL SURROUND STEREO VIDEO AUDIO

SOUND INPUT

AUDIO ASSIGNSPEAKER

ON / OFF

TONE CH.LEVEL SETUP ENTER / MEMO BANDPRESETTUNE

PHONES AUX 1 AUX 2

POWER

STANDBY

NETWORK AV RECEIVER RD-606i

USB

5V 1A

RETURN MAIN MENU

MASTER VOLUME

Bluetooth IN

LOADING BATTERIES

REMOTE CONTROL OPERATION RANGE

• Use the remote control unit within a range of about 7 meters (23

feet) and angles of up to 30 degrees aiming at the remote sensor.

• Remove the batteries when they are not used for a

long time.

• Do not use the rechargeable batteries (Ni-Cd type).

1. Remove the cover. 2. Load two batteries ("AAA" size, 1.5 V) matching

the polarity.

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 14

ENGLISH

Operations

LISTENING TO A PROGRAM SOURCE

Before operation

• Enter the standby mode.

• The STANDBY indicator lights up.

This means that the receiver is not disconnected from

the AC mains and a small amount of current is

retained to support the operation readiness.

• To switch the power off, push the POWER switch again.

• Then the power is cut off and the STANDBY indicator

goes off.

• Each time the POWER ON/STANDBY button on the front panel is

pressed, the receiver is turned on to enter the operating mode or off

to enter the standby mode.

• On the remote control, press the POWER ON button to enter the

operating mode or press the STANDBY button to enter the standby

mode.

POWER

ON / STANDBY

1. In the standby mode, turn the power on.

3. Select the desired input source.

■Note : Before operating this receiver, first set this unit as desired for optimum performance, doing the system setup

procedures. (For details, refer to "System Setup" on page 36.)

• Then “SPEAKER ON” is displayed and the sound can be heard from

the speakers connected to the speaker terminals.

• When using the headphones for private listening, press the

SPEAKER button again to switch the speakers off (“SPEAKER OFF”

is displayed).

2. Switch the speakers on.

• Each time the “VIDEO” button on the front panel is

pressed, the input source changes as follows:

→VIDEO 1 →VIDEO 2

• Each time the “AUDIO” button on the front panel is

pressed, the input source changes as follows:

→CD→AUX 1→TV*→AUX 2→TAPE→BT→NET/USB →TUNER

(Frequency display)

* : Only when the HDMI CONTROL is set to ON, you can

hear the digital audio signals from TV via a HDMI cable.

(For details, refer to “When selecting the HDMI

CONTROL” on page 49.)

• When selecting NET/USB, refer to “LISTENING TO

INTERNET RADIO BROADCASTS, MUSIC FILES” on

page 25.

• Each time the BAND button(or the TUNER button on the

remote control) is pressed, the band changes as follows:

→ FM STEREO → FM MONO → AM

When CD, VIDEO 1 ~ 2 is selected as an input source

AUDIO ASSIGN

RETURN

4. Select the digital or the analog input connected as

desired.

• Each time this button is pressed, the corresponding input

is selected as follows:

→OPT →COAX.1 → COAX.2 → ANALOG

■Notes :

• When the HDMI IN connector is connected to your video

component, you cannot assign the audio input as desired.

(It means that only the HDMI digital audio signals can be

heard.)

• When the HDMI IN connector is not connected (and the

“HDMI” indicator flickers), you can assign the audio input.

• When AUX 1, AUX 2, TAPE, TV, BT, NET/USB or tuner is

selected as an input source, the signal input cannot be

selected.

• When the selected digital input is not connected, the

“D(Digital)” indicator flickers and the analog input is

automatically selected.

• The selected digital input or analog input is automatically

assigned to the corresponding input source on the INPUT

setup menu. (For details, refer to “SETTING THE INPUT

SETUP” on page 40.)

• The sound from the component connected to the selected

digital input can be heard regardless of the selected input

source.

INPUT

BAND

AUDIO

VIDEO

■Auto Power Save

• The auto power save is a function that automatically turns the

power off to enter the standby mode. When any button is not

pressed for more than the time you set, it will function. (For details,

refer to “When selecting the AUTO POWER SAVE” on page 38.)

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 15

ENGLISH

TONE

TUNE

• Each time these buttons are pressed, the tone mode is

selected as follows :

OFF : To listen to a program source without the

↕tone effect.("DIR" lights up.)

ON : To adjust the tone for your taste.("DIR" goes off.)

• Each time these buttons are pressed, the tone is selected as

follows:

→BASS ↔TREBLE ↔TONE: ON ←

■When the TONE is set to ON to adjust the tone

(bass and treble).

• The tone level can be adjusted within the range of -10 ~

+10 dB.

• In general, we recommend the bass and treble to be

adjusted to 0 dB (flat level).

• Extreme settings at high volume may damage your

speakers.

• If the tone display disappears, start from the step 9 again.

Adjusting the tone (bass and treble)

TO O

NE :

FM MH P0 1

-30

• The tone mode is

displayed for several

seconds.

9. Enter the tone mode.

10. Press the CURSOR LEFT(◀)/RIGHT(▶)

buttons to select the desired tone mode.

11. Press the CURSOR UP(▲)/DOWN(▼) buttons

to select the desired tone.

12. Press the CURSOR LEFT(◀)/RIGHT(▶)

buttons to adjust the selected tone as desired.

PRESET

• Be sure to switch the speakers off.

• When listening to a DTS or Dolby Digital program source,

if the headphones are plugged in and the SPEAKER

button is set to off, it enters the 2CH downmix mode

automatically. (For details, refer to “2CH downmix

mode”on page 18.)

■Note:

• Be careful not to set the volume too high when using

headphones.

• When playing back the program sources with surround

sound, refer to “ENJOYING SURROUND SOUND” on

page 18.

• “MUTING” is displayed.

• To resume the previous sound level, press it again.

MASTER VOLUME

DOWN UP

MUTE

PHONES

5. Operate the selected component for playback.

6. Adjust the (overall) volume.

7. To mute the sound.

8. To listen with the headphones.

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 16

ENGLISH

SURROUND SOUND

• This receiver incorporates a sophisticated Digital Signal Processor that allows you to create optimum sound quality and sound

atmosphere in your personal Home Theater.

■DTS Digital Surround

DTS Digital Surround(also called simply DTS) supports up to

5.1 discrete channels and uses less compression for high

fidelity reproduction. Use it with DVDs and CDs bearing the

DTS logo.

■DTS 96/24

This is high resolution DTS with a 96 kHz sampling rate and

24 bit resolution, providing superior fidelity. Use it with DVDs

bearing the DTS 96/24 logo.

Manufactured under license under U.S. Patent Nos:

5,956,674; 5,974,380; 6,487,535 & other U.S. and worldwide

patents issued & pending. DTS, the Symbol, & DTS and the

Symbol together are registered trademarks & DTS Digital

Surround and the DTS logos are trademarks of DTS, Inc.

■Dolby Digital

Dolby Digital is the multi-channel digital signal format

developed by Dolby Laboratories. Discs bearing the Dolby

Digital logo includes the recording of up to 5.1 channels of

digital signals, which can reproduce much better sound

quality, spatial expansion and dynamic range

characteristics than the previous Dolby Surround effect.

■Dolby Pro Logic II surround

This mode applies conventional 2- channel signals such as

digital PCM or analog stereo signals as well as Dolby

Surround signals, etc. to surround processing to offer

improvements over conventional Dolby Pro Logic circuits.

Dolby Pro Logic ll surround includes 2 modes as follows:

• Dolby Pro Logic ll Movie

When enjoying movies, this mode allows you to further

enhance the cinematic quality by adding processing that

emphasizes the sounds of the action special effects.

• Dolby Pro Logic ll Music

When listening to music, this mode allows you to further

enhance the sound quality by adding processing that

emphasizes the musical effects.

■Dolby Pro Logic

This mode expands any 2-channel source(including Dolby

Surround source) for 4 channel(front left, center, front right

and surround) playback.

The surround channel is monaural, but is played through

two surround speakers.

Manufactured under license from Dolby Laboratories.

Dolby, Pro Logic, and the double-D symbol are registered

trademarks of Dolby Laboratories.

• The following modes apply conventional 2-channel

signals such as digital PCM or analog stereo signals to

high performance Digital Signal Processor to recreate

sound fields artificially. Select one of the 6 provided

surround modes according to the program source you

want to play.

■Theater

This mode provides the effect of being in a theater when

watching a play.

■Movie

This mode provides the effect of being in a movie theater

when watching a movie.

■Hall

This mode provides the ambience of a concert hall for

classical music sources such as orchestral, chamber music

or an instrumental solo.

■Game

This mode is suitable for video games.

■Stadium

This mode provides the expansive sound field to achieve

the true stadium effect when watching baseball or soccer

games.

■Multi CH Stereo

This mode is designed for playing background music. The

front and surround channels create a stereo image that

encompasses the entire area.

Surround modes

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 17

ENGLISH

ENJOYING SURROUND SOUND

• Each time this button is pressed, the mode changes as follows :

Auto surround mode : The optimum surround mode will be

automatically selected depending on the signal

format being input.

Manual surround mode : You can select the desired of different

surround modes selectable for the signal

being input with using the SURROUND

MODE SELECT (>/<) buttons.

: When “CENTER” and “SURR”(Surround) are set to “NO”, any surround mode cannot be selected and the source can be

reproduced either in the stereo mode or in the 2CH downmix mode.

■Notes :

• When the SPEAKER button is set to off or “CENTER” and “SURR”(Surround) are set to “NO”, the auto surround mode is invalid.

• Even when the auto surround mode is selected and the same type of digital signal format is being input, the optimum

surround mode may vary depending on whether the speaker type is set to "NO" or not.

• When the auto surround mode is selected, the surround modes other than the optimum surround mode cannot be selected.

■When selecting the manual surround mode with pressing the AUTO/MANUAL button on the front panel

Select the desired surround mode.

■Note: Before surround playback, first perform the speaker setup procedure, etc. on the SETUP menu for optimum performance.

(For details, refer to "SETTING THE SPEAKER SETUP" on page 41.)

Depending on how to select a surround mode, select the auto surround mode or the manual surround mode.

("AT(Auto)" indicator

lights up.)

("AT(Auto)" indicator

goes off.)

• Each time the SURROUND MODE SELECT (>/<)

buttons are pressed, the surround mode changes

depending on the input signal format as follows :

AUTO/MANUAL

SOUND

SURROUND

DOLBY DIGITAL or <2 CH IN> *1

DOLBY PLII MOVIE, DOLBY PLII MUSIC, THEATER, MOVIE, HALL, GAME, STADIUM,

MULTI CH STEREO, DOLBY PRO LOGIC or <2 CH IN> *1

Corresponding DTS mode or <2 CH IN>*1

Dolby Digital EX 6.1 channel sources,

Dolby Digital 5.1 channel sources

Dolby Digital 2 channel sources,

PCM (2 channel) sources,

Analog stereo sources

DTS sources,

DTS 96/24 sources

Signal format being input Selectable surround mode

■To cancel the surround mode for stereo operation

• Depending on the signal format which is being input, either the

stereo mode or the 2CH downmix mode is selected.

• To cancel either the stereo mode or the 2CH downmix

mode, select the surround mode with using the SURROUND

MODE SELECT (>/<) buttons.

■2CH downmix mode

• This mode allows the multi-channel signals encoded in DTS or Dolby Digital format to be mixed down into 2 front channels and

to be reproduced through only two front speakers or through headphones.

• When the SPEAKER button is set to off to listen with headphones while playing the multi-channel digital signals from DTS or

Dolby Digital sources, it will enter the 2CH downmix mode automatically.

STEREO

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 18

ENGLISH

• While playing digital signals form Dolby Digital program source or listening in Dolby Pro Logic II Music mode, you can

adjust their parameters for optimum surround effects.

• Then “DRC: ~” (or “PANORAMA : ~ ”) is displayed for

several seconds.

• If the parameter mode disappears, press this button again.

When adjusting the sound parameters

1. Press the SOUND PARAMETER button.

PRESET

2. Press the CURSOR UP(▲)/DOWN(▼) buttons

to select the desired parameter.

• Each time these buttons are pressed, the parameter mode

changes as follows:

→"DRC"↔"PANORAMA"↔"C.WIDTH"↔"DIMENSIOM"←

(Dynamic Range (Center width

Compression) control)

• "DRC" can be selected only while playing digital signals

from Dolby Digital source.

• "PANORAMA", "C.WIDTH" and "DIMENSION" can be

selected only while listening in Dolby Pro Logic II Music

mode.

■When selecting the "DRC (Dynamic Range

Compression)"

• This function compresses the dynamic range of

previously specified parts of the Dolby Digital sound track

(with extremly high volume) to minimize the difference in

volume between the specified and non-specified parts.

This makes it easy to hear all of the sound track when

watching movies at night at low levels.

■Note :

• In some Dolby Digital softwares, DRC setting may not be

valid.

→OFF : To turn off the DRC function. (Default value)

↕

MID

↕

→ MAX

■When selecting the "PANORAMA"

This mode extends the front stereo image to include the

surround speakers for an exciting "wraparound" effect with

side wall imaging.

Select "OFF" or "ON"(default value: OFF).

■When selecting the "C. WIDTH(Center width)" control

This adjusts the center image so it may be heard only from

the center speaker, only from the left/right speakers as a

phantom image, or from all three front speakers to varying

degrees.

The control can be set in 8 steps from 0 to 7(default value :

3).

■When selecting the "DIMENSION" control

This gradually adjusts the soundfield either towards the

front or towards the rear. The control can be set in 7 steps

from -3 to +3 (default value : 0).

TUNE

3. Press the CURSOR LEFT(◀)/ RIGHT(▶)

buttons to adjust the selected parameter as

desired.

4. Repeat the above steps 2 and 3 to adjust other

parameters.

Higher compression

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 19

ENGLISH

TUNE

• The volume level of each channel can be adjusted easily with the test tone function.

■Note : When the SPEAKER button is set to off, the test tone function does not work.

Adjusting each channel level with test tone

• The test tone mode is displayed and will be heard from

the speaker of each channel for 2 seconds as follows:

→FL →C →FR →SR →SL →SW

Front Center Front Surround Surround Subwoofer

Left Right Right Left

• When the speaker setting is "NO", the test tone of the

corresponding channel is not available.

1. Enter the test tone mode. 2. At each channel, adjust the level as desired until

the sound level of each speaker is heard to be

equally loud.

3. Cancel the test tone function.

• You can select the desired channel with pressing the

CURSOR UP(▲)/DOWN(▼) buttons.

RD-606i(A)_ENG_110414_RD-606i(A)_ENG 2011-05-04 오후 2:13 페이지 20

La page charge ...

Sherwood RD-606I Mode d'emploi

Marque: Sherwood

Modèle: RD-606I

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Sherwood RD-606I Operating instructions
español: Sherwood RD-606I Instrucciones de operación

Sherwood RD-606I Mode d'emploi

Sherwood RD-606I Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents