Ubiquiti UVC-Micro Mode d'emploi

Model: UVC-Micro

Quick Start Guide

®

Package Contents

UVC-Micro

Camera

UVC-Micro

Base

Power

Adapter

Flat Base

Plate

Corner Base

Plate

Mounting

Tape

Screws

(Qty. 5)

Screw

Anchors

(Qty. 5)

Cable Clips

(Qty. 6)

Hardware Overview

LED

Reset

LED The LED will light steady blue

during bootup. When the camera is

ready to connect to the Wi-Fi network,

the LED pattern will flash two times

accompanied by two beep tones. Once

connected to the network, the LED will

glow a breathing pattern.

Reset To reset network settings to

factory defaults, press and hold the

Reset button until the camera beeps two

fast tones.

Installation

Install the UVC-Micro within 5 m (16')

of a power outlet. The camera has

a magnetic base that can be used

to mount it on a metal surface and

includes mounting kits for standard

wall or corner mounting. Follow the

appropriate steps for your installation.

Mount on Metal Surface

1. Attach the UVC‑Micro Camera and the

power cable to the UVC‑Micro Base.

2. Attach the camera assembly to a

metal (steel) surface.

Wall Mounting

Mount with tape or with screws:

Mounting with Tape

1. Remove the paper from one side of

the Mounting Tape, and center the

tape on the back of the Flat Base Plate.

2. Remove the paper from the other

side of the Mounting Tape and attach

the Flat Base Plate to the wall.

Mounting with Screws

1. Place the Flat Base Plate at the desired

location and mark the two mounting

holes.

Note: If you are running the power

cable inside the ceiling or wall,

then mark the cable feed opening

below the mounting holes.

2. Use a 3 mm drill bit to drill a hole at

each mark, and insert a Screw Anchor

into each hole.

3. (Optional) When running the power

cable inside the wall or ceiling, cut the

hole for the power cable. Then feed

the cable through the hole and the

Flat Base Plate.

4. Attach the Flat Base Plate to the

surface by fastening a Screw to each

Screw Anchor.

*640-00157-01*

640-00157-01

Corner Mounting

1. Place the Corner Base Plate at the

desired location and mark the two

mounting holes.

2. Use a 3 mm drill bit to drill a hole at

each mark, and insert a Screw Anchor

into each hole.

3. Feed the power cable through the

back of the Corner Base Plate.

4. Secure the Corner Base Plate by

fastening a Screw to each Screw

Anchor.

Attaching the Camera

1. Attach the power cable to the back of

the UVC‑Micro Base.

2. Connect the UVC‑Micro Base to the

Base Plate by inserting the mounting

tabs into the slots on the base.

3. Rotate the UVC‑Micro Base to lock it.

4. Attach the UVC‑Micro Camera to the

UVC‑Micro Base, and pivot the camera

to the desired angle.

Connecting Power

The included Power Adapter has a 5 m

(16') power cable that is hidden inside

the adapter casing.

Extend the power cable as needed, by

following these steps:

1. Hold the outer casing of the Power

Adapter with the Ubiquiti® U logo

facing toward you, and push in the

center of the logo until the adapter

releases from the outer casing.

2. Unwind the power cable to extend it

to the desired length. Then lock the

cable into the notch located under

the bottom of the U logo.

3. Slide the outer casing back onto the

adapter until it snaps into place.

4. Plug the Power Adapter into a power

outlet. To secure the connection, use

the outlet cover plate screw to fasten

the Power Adapter to the outlet.

(Optional)

Note: (6) Cable Clips with adhesive

tape are included to help hold

the power cable in place. Remove

the paper backing on each clip to

expose the adhesive tape.

Adopting the Camera

Use the Unifi Video mobile app for iOS

or Android to adopt and configure the

camera. The app is available free in the

app/play store.

Alternatively, you can adopt and

configure the camera using Wi-Fi and a

web browser.

1. Connect your host machine Wi-Fi

to the camera’s access point (SSID)

named: Setup UVC Micro (xxxx)

(where xxxx is the last four characters

of the MAC address of the UVC-Micro)

2. Launch a web browser and go to:

https://192.168.1.20

3. The login screen will appear. Enter

ubnt in the Username and Password

fields and click Login.

4. The Main screen will appear and you

should see a live video stream from

the camera. Click the Device tab.

5. On the Device page, click Scan

Networks. Then choose your network

that is running the UniFi Video

software.

Note: If your network is hidden or

does not show up in the SSID list,

enter it manually in the next step.

6. Under the Wireless Network Settings

section, enter the SSID and Security

settings of your UniFi Video network.

Click Save Changes.

7. The UVC-Micro will reboot and

connect to your UniFi Video network.

8. Connect your host machine to the

same UniFi Video network.

UniFi Video

Ensure that you are running UniFiVideo

software version 3.1.0 or higher.

The latest version of the UniFi Video

software is available at

downloads.ubnt.com/unifivideo

Once the UVC-Micro and the UniFi

Video software are connected to

the same network, the UniFi Video

auto-management feature should

automatically detect and install your

new camera(s).

For details on using the UniFi Video

software, refer to the User Guide at

documentation.ubnt.com/unifivideo

Specifications

UVC-Micro

Dimensions

40.7 x 40.7 x 40.8 mm

(1.61 x1.61 x 1.61")

Weight 53 g (1.87oz)

Network Interface 2.4/5 GHz Dual-Band Wi-Fi

Sensor

Progressive Scan

RGB CMOS 1/4"

Lens EFL=2.38 mm / F2.4

View Angle 79.13° (H), 54.15° (V), 88.45° (D)

Night Mode

Infrared LEDs with

Mechanical IR Cut Filter

Video Compression H.264

Resolution 720p HD (1280 x 720)

Max. Frame Rate 30 FPS

Microphone Yes

Speaker* Yes

Flash Memory Support microSD (Max. 32 GB)

Power Supply

5.5V (5,5V) Adapter with

5 m (16') Power Cable

Max. Power

Consumption

3.2W

Mounting Wall/Ceiling/Corner Kit

Operating Temperature 0 to 35° C (32 to 95° F)

Operating Humidity 20 to 90% Noncondensing

* Functionality coming soon with a software update

La page est en cours de chargement...

Ubiquiti UVC-Micro Mode d'emploi

Ce manuel convient également à

Ubiquiti UVC-Micro Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents