Ubiquiti UniFi LED ULED-AT Guide de démarrage rapide

Marque: Ubiquiti

Modèle: UniFi LED ULED-AT

Catégorie: Commutateurs réseau

Taper: Guide de démarrage rapide

LED

Network-Managed

LED Panel Powered by PoE+

Model: ULED-AT

Introduction

Thank you for purchasing the Ubiquiti Networks® UniFi®LED

Panel. This Quick Start Guide is designed to guide you through

installation and includes warranty terms.

Package Contents

LED

Network-Managed

LED Panel Powered by PoE+

Model: ULED-AT

UniFi LED Panel Quick Start Guide

System Requirements

• An 802.3at-compliant network switch

• UniFi LED mobile app software

• Mobile device: iOS 10 or Android 5.0

• UniFi LED Controller software

• Computer: UniFi Application Server (UAS) 0.5.0,

Ubuntu 16.04 LTS (Xenial Xerus) 64-bit or Debian 9 64-bit

• Web browser: Google Chrome (Other browsers may have

limited functionality.)

• UniFi Dimmer Switch, model UDIM-AT or UDIM-AC

Network Topology Requirements

There are three ways to control the UniFi LED Panel:

UniFi Dimmer Switch Users in the immediate vicinity control

the UniFi LED Panel using the UniFi Dimmer Switch.

UniFi LED App over Layer 2 Network A local user runs the

app to connect to a UniFi AP on the same Layer 2 network as

the UniFi LED Panel.

UniFi LED Controller over Layer 2 Network Alocal user runs

the LED Controller software on the same Layer 2 network as

the UniFi LED Panel.

UniFi PoE Switch

Internet

LAN

WAN

UAP-AC-PRO

802.3at PoE+

ULED-AT

UniFi Application Server

UniFi LED

Controller

UDIM-AT

UniFi LED

App

802.3af PoE

USG-PRO-4

(DHCP Server)

Sample Network Diagram

*640-00332-09*

640-00332-09

Network topology requirements are as follows:

• DHCP-enabled network (for the UniFi LED Panel to obtain

an IP address)

• For UniFi Dimmer Switch only:

A UniFi Dimmer Switch connected to the same Layer 2

network as the UniFi LED Panel

• For LED Controller software:

A UniFi Application Server running the UniFi LED Controller

software and connected to the same Layer 2 network as the

UniFi LED Panel

• For UniFi LED app only:

A UniFi AP connected to the same Layer 2 network as the

UniFi LED Panel

Hardware Overview

Status LED

LED

LED Color Status

Flashing White Initializing.

Steady White System ready.

Steady Blue Adopted by LED Controller.

Alternating

White/Blue

Firmware upgrade is taking place.

ULED-AT-XXXXXX

Reset

PoE+

MAC

Sticker

Port

PoE+ The PoE+ port is a 10/100 Ethernet port used to connect

the power and should be connected to the LAN. Power is

provided by a UniFi Switch with 802.3at PoE+.

Note: The PoE+ port requires 25W of power, which can

be supplied by an 802.3at-compliant UniFi Switch.

MAC Sticker Used to scan the MAC address. For details, refer

to “Quick Setup”.

Button

Reset The Reset button serves two functions:

• Restart Press and release the Reset button quickly.

• Restore to Factory Default Settings Press and hold the

Reset button for more than five seconds.

Installation

To install and configure the UniFi LED Panel:

1. Connect one end of an Ethernet cable to the PoE+ port on

the back of the UniFi LED Panel.

2. Connect the other end of the cable to an 802.3at-compliant

switch port that can provide 25W PoE+.

3. Lift the panel and seat it in an opening in the ceiling grid.

Configuring the UniFi LED Panel

Follow the instructions for the software you wish to use:

UniFi LED App

1. Install the UniFi LED app on your smartphone or mobile

device. The app is available from the App Store® or

GooglePlay

™

Store.

2. Launch the app.

3. Follow the on-screen instructions to configure the UniFi

LED Panel.

UniFi LED Controller Software

1. Install the latest version of the UniFi LED Controller

software on a computer on the same Layer 2 network as

the UniFi LED Panel:

• Ubuntu users Download the software from

www.ubnt.com/download/unifi-led

• UAS users Install the software using the UAS

management console.

2. Launch a web browser and go to https://localhost:20443

3. The UniFi LED Controller will appear, allowing you to

configure the UniFi LED Panel, as well as customize other

settings.

For additional details on the UniFi LED Controller, refer to

the documentation at:

www.ubnt.com/download/unifi-led

Quick Setup

This section describes the Quick Setup procedure for

installations with large numbers of UniFi LED Panels and

Dimmer Switches. The Quick Setup requires using the UniFi

LED app along with a QR Code Log that you create. Each UniFi

LED Panel or Dimmer Switch has a removable MAC Sticker on

its reverse side; this has a QR code used to scan the device’s

MAC address. The Quick Setup consists of these steps:

• Create the QR Code Log

• Install the LED Panels and Dimmer Switches

• Scan the QR codes

Create the QR Code Log

1. Download the QR Code Log template at:

ubnt.link/QR-Code-Log

2. Print out as many copies as needed (each sheet can log up

to 16 LED Panels and 3Dimmer Switches).

Site:

Controller:

QR Code Log

UDIM-AT-XXXXXX

arrows and place them on this QR Code Log.

3. Fill in the Site (such as “1st Floor Meeting Room”) and

Controller (such as “UniFi LED Controller”) on each sheet.

Install the LED Panels and Dimmer Switches

For each UniFi LED Panel or Dimmer Switch:

1. Remove the MAC Sticker from the back of the device by

carefully peeling back and pulling the blue tab.

2. Place the sticker on the QR Code Log sheet that matches

the device’s location.

Site:

Controller:

QR Code Log

UDIM-AT-XXXXXX

arrows and place them on this QR Code Log.

ULED-AT-XXXXXX

Site:

Controller:

QR Code Log

UDIM-AT-XXXXXX

arrows and place them on this QR Code Log.

UDIM-AT-XXXXXX

3. Install the device as decribed in the Installation section of

the device’s Quick Start Guide.

Scan the QR Codes

1. On your mobile device, open the UniFi LED app.

2. Go to the More screen. Tap Quick Setup.

3. Follow the instructions as the UniFi LED app guides you

through the process of adding devices by scanning the QR

codes on the QR Code Log sheet(s).

Note: Instead of scanning the QR codes, you can also use

the UniFi LED app’s Locate function to identify and assign

individual LED Panels to their groups; however, this is

best suited for smaller installations.

Specifications

ULED-AT

Dimensions 602 x 602 x 56.7 mm (23.7 x 23.7 x 2.23")

Weight 4.5 kg (9.92 lb)

Networking Interface 10/100 Mbps Ethernet Port

Connectivity Bluetooth 4.1

Buttons Reset

LEDs Status

Power Method 802.3at PoE+

Supported Voltage Range Standard PoE+ 42.5-57.0V

Max. Power Consumption 25.5W

Mounting Standard T-Grid

Operating Temperature 0 to 40° C (32 to 104° F)

Certications FCC, IC

Lighting

Initial Delivered Luminance

(Max.)

2300 lm

Efcacy 100 lm/W*

CCT 4,000 K

L80 > 50,000 hrs

CRI > 80

Beam Angle 114°

Brightness Control 10-100% Dimming

Environment Indoor Dry Location

* Based on power delivered to the LED Panel

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in a location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

Limited Warranty

www.ubnt.com/support/warranty

The limited warranty requires the use of arbitration to resolve disputes on

an individual basis, and, where applicable, specify arbitration instead of

jury trials or class actions.

Compliance

FCC

Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions.

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment.

Thisequipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operations of

this equipment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his

own expense.

This radio transmitter FCC ID: SWX-ULEDAT has been approved by FCC.

ISED Canada

CAN ICES-3(A)/NMB-3(A)

This device complies with ISED Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that

may cause undesired operation of the device.

This radio transmitter (IC: 6545A-ULEDAT) has been approved by ISED

Canada.

CAN ICES-3(A)/NMB-3(A)

Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux

appareils radio exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes :

1. l’appareil ne doit pas produire de brouillage;

2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

Le présent émetteur radio (IC : 6545A-ULEDAT) a été approuvé par ISDE

Canada.

Online Resources

Website www.ubnt.com

Support help.ubnt.com

Community community.ubnt.com

Downloads downloads.ubnt.com

Ubiquiti Networks, Inc.

685 Third Avenue, 27th Floor

New York, NY 10017

USA

Networks, the Ubiquiti U logo, the Ubiquiti beam logo, and UniFi are

trademarks or registered trademarks of Ubiquiti Networks, Inc. in the

United States and in other countries. Apple and the Apple logo are

trademarks of Apple Inc., registered in the U.S. and other countries. App

Store is a service mark of Apple Inc., registered in the U.S. and other

countries. Android, Google, Google Play, the Google Play logo and other

marks are trademarks of Google LLC. All other trademarks are the property

of their respective owners. AIJL031819

IMPORTANT NOTE:

Radiation Exposure Statement:

• This equipment complies with FCC and IC radiation exposure limits set

forth for an uncontrolled environment.

• This equipment should be installed and operated with minimum

distance 20 cm between the radiator & your body.

• This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

AVIS IMPORTANT :

Déclaration sur l’exposition aux rayonnements

• Cet équipement est conforme aux limites prévues par la FCC et IC pour

l’exposition aux rayonnements dans un environnement non contrôlé.

• Lors de l’installation et de la mise en fonctionnement de l’équipement,

assurez-vous qu’il y ait une distance minimale de 20 cm entre l’élément

rayonnant et vous.

• Cet émetteur ne doit être installé à proximité d’aucune autre antenne

ni d’aucun autre émetteur, et ne doit être utilisé conjointement à aucun

autre de ces appareils.

Ubiquiti UniFi LED ULED-AT Guide de démarrage rapide

Marque: Ubiquiti

Modèle: UniFi LED ULED-AT

Catégorie: Commutateurs réseau

Taper: Guide de démarrage rapide

Télécharger le PDF

rapport

dans d''autres langues

English: Ubiquiti UniFi LED ULED-AT Quick start guide

Ubiquiti UniFi LED ULED-AT Guide de démarrage rapide

Ubiquiti UniFi LED ULED-AT Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents