Sub-Zero ICBCT30G Manuel utilisateur

GAS COOKTOPS

USE & CARE INFORMATION

GUÍA DE USO Y MANTENIMIENTO

GUIDE D’UTILISATION ET D’ENTRETIEN

INFORMAZIONI SU USO E MANUTENZIONE

BEDIENUNGS- UND PFLEGEANLEITUNG

3

ENGLISH

Wolf Gas Cooktops 5

Safety Instructions and Precautions 6

Wolf Gas Cooktop Features 10

Wolf Gas Cooktop Use & Care 12

Wolf Troubleshooting Guide 19

Wolf Service Information 20

ESPÃNOL

Placas de gas de Wolf 22

Precauciones e instrucciones de seguridad 23

Características de las placas de gas de Wolf 27

Uso y mantenimiento de la placa de gas

de Wolf 29

Guía de localización y solución de problemas

de Wolf 36

Información de mantenimiento de Wolf 37

FRANÇAIS

Plaques de cuisson au gaz Wolf 39

Instructions et mesures de sécurité 40

Caractéristiques des plaques de cuisson

au gaz Wolf 44

Utilisation et entretien de la plaque de

cuisson au gaz Wolf 46

Guide de dépistage des pannes Wolf 53

Service après-vente Wolf 54

ITALIANO

Piani cottura a gas Wolf 56

Precauzioni e istruzioni di sicurezza 57

Funzioni dei piani cottura a gas Wolf 61

Uso e manutenzione dei piani cottura

a gas Wolf 63

Guida alla soluzione dei problemi Wolf 70

Informazioni sull’assistenza Wolf 71

INHALT

Gaskochmulden von Wolf 77

Sicherheitshinweise und Vorsichtsmaßnahmen 78

Leistungsmerkmale der Gaskochmulden von Wolf 82

Bedienung und Pflege von Gaskochmulden

von Wolf 84

Anleitung zur Fehlersuche von Wolf 91

Serviceinformationen von Wolf 92

As you read this Use & Care Information,

take particular note of the CAUTION and

WARNING symbols when they appear.

This information is important for safe and

efficient use of the Wolf equipment.

In addition, this Use & Care Information may

signal an IMPORTANT NOTE which highlights

information that is especially important.

signals a situation where minor injury or

product damage may occur if you do not

follow instructions.

states a hazard that may cause serious

injury or death if precautions are not

followed.

WOLF

®

is a registered trademark of Wolf Appliance, Inc.

5

THANK YOU

Your purchase of a Wolf gas cooktop attests

to the importance you place upon the quality

and performance of your cooking equipment.

We understand this importance and have

designed and built your cooktop with quality

materials and workmanship to give you years

of dependable service.

We know you are eager to start cooking, but

before you do, please take some time to read

this Use & Care Information. Whether you are

a beginning cook or an expert chef, it will be

to your benefit to familiarize yourself with the

safety practices, features, operation and care

recommendations of the Wolf gas cooktop.

If service is necessary, refer to the model

and serial number of the gas cooktop. Both

numbers are listed on the product rating plate

located on the underside of the cooktop.

Refer to the illustration below.

WOLF GAS COOKTOPS

IMPORTANT NOTE:

Installation and service must be

performed by a qualified installer,

service agency or the gas supplier.

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appli-

ance.

The use of a gas cooking appliance

results in the production of heat and

moisture in the room in which it is

installed. Ensure that the kitchen is

well ventilated; keep natural ventila-

tion holes open or install a mechani-

cal ventilation device (mechanical

extractor hood).

Prolonged intensive use of the appli-

ance may call for additional ventila-

tion, for example opening of a

window, or more effective ventila-

tion, for example increasing the

level of mechanical ventilation

where present.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch.

Do not use any phone in your

building.

Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

If you cannot reach your gas

supplier, call the fire department.

CONTACT

INFORMATION

Website:

wolfappliance.com

This appliance shall be installed

in accordance with the regula-

tions in force and only used in a

well ventilated space. Read the

instructions before installing or

using this appliance.

Rating plate location

Location of rating

plate under cooktop

6

WHAT TO DO

IMPORTANT NOTE: Read all

instructions before using this

appliance.

Read this Use & Care Information

carefully before using your new

cooktop to reduce the risk of fire,

electric shock or injury to persons.

Ensure proper installation and

servicing. This appliance must be

properly installed and grounded by

a qualified technician. Learn how

and where to turn off the gas to the

cooktop.

Before performing any service, turn

off the gas supply and unplug the

cooktop electrical power cord from

the wall receptacle.

SAFETY INSTRUCTIONS AND PRECAUTIONS

Keep igniters clean and dry for

proper lighting and performance of

the burners.

In the event that a burner goes out

and gas escapes, open a window or

a door. Wait at least five minutes

before using the cooktop.

Adequate supply of air. Your kitchen

must provide an adequate supply of

fresh air to ensure proper combus-

tion and ventilation.

Start the ventilation hood approxi-

mately five minutes before cooking

on the cooktop; this establishes an

air curtain, and improves the capture

of vapor and moisture.

Wear proper apparel. Never let loose

clothing or other flammable materi-

als come in contact with the burners

while in operation. Fabric may ignite

and cause personal injury.

7

When deep fat frying, be sure that

the pan is large enough to accom-

modate the desired volume of food

without overflow caused by

bubbling of the fat. Never leave a

deep fat fryer unattended. Avoid

deep fat frying of moist or frost-

covered foods, as foods with high

water content may cause spattering

or spilling of the hot fat. Heat fat

slowly, and stir together any combi-

nations of oils and fats prior to

applying heat. Use a deep fat frying

thermometer to avoid heating the fat

to temperatures above the flash

point.

Always light each burner prior to

placing a pan on the burner grate.

Also, turn the control knob to the

position before removing a pan

from the burner grate.

WHAT TO DO

Always use dry pot holders when

removing pans from the cooktop.

Wet or damp pot holders can cause

steam burns. Do not use a towel or

bulky cloth in place of pot holders.

Choose pans with easily grasped

handles that will stay cool while

cooking. Refer to Cookware Selec-

tion on page 16.

When cooking, set burner controls

so that the flame does not extend

beyond the bottom of the pan.

Always turn panhandles inward so

they do not extend over adjacent

work areas, burners or the edge of

the cooktop.

Always check the positions of the

control knobs to make certain the

cooktop is off when you are finished

cooking.

8

SAFETY INSTRUCTIONS AND PRECAUTIONS

Keep appliance area clear and free

from combustible material.

Do not block or obstruct the holes

in the cooktop surface below the

control knobs. Blocking these holes

may affect burner operation and

may result in a hazard.

When using the cooktop, do not

touch the grates, burner caps,

burner bases or any other parts in

proximity to the flame. These

components may be hot enough to

cause burns.

If the cooktop is near a window, do

not use long curtains as a window

treatment, as they could blow over

the cooktop and create a fire hazard.

Do not leave children alone or

unattended in the area where the

cooktop is in use. Never allow

children to sit or stand on the

appliance. Do not let children play

with the cooktop.

Do not store items of interest to

children above or at the back of the

cooktop, as they could climb on the

appliance to reach items and be

injured.

WHAT NOTTODO

Do not repair or replace any part of

the cooktop unless specifically

recommended in literature accompa-

nying this appliance. All service

should be referred to a qualified

technician.

Do not obstruct the flow of combus-

tion and ventilation air.

Do not use aluminum foil to line any

part of the cooktop.

Never use the cooktop to warm or

heat the room.

Do not store flammable materials

near burners or let grease or other

flammable substances accumulate

on the cooktop.

Do not use abrasive or caustic

cleaners or detergents on this appli-

ance as these may cause permanent

damage. Do not use aerosol

cleaners as these may be flammable

or cause corrosion of metal parts.

Do not store or use gasoline or

other flammable vapors and liquids

in the vicinity of this or any other

appliance.

9

TO REDUCE THE RISK OF INJURY

TO PERSONS IN THE EVENT OF

A COOKTOP GREASE FIRE,

OBSERVE THE FOLLOWING:

Smother flames with a close-

fitting lid, baking sheet or other

metal tray, then turn off the gas

burner. Be careful to prevent

burns. If the flames do not go out

immediately, evacuate and call

the fire department.

Do not use water on grease fires.

Never pick up a flaming pan—

you may be burned.

WHAT NOTTODO

Do not use water on grease fires.

Smother the flame or use a dry

chemical or foam-type extinguisher.

Never leave the appliance unat-

tended when in use. Boilovers and

greasy spills may smoke or ignite.

Do not cover the burners and grates

with anything except properly

selected utensils. Decorative covers

should not be used.

Do not heat unopened food contain-

ers such as baby food jars and cans.

Pressure buildup may cause the

container to burst and cause injury.

Do not clean the cooktop while it is

still hot. If using a damp sponge or

cloth, wait until the cooktop has

cooled sufficiently to prevent steam

burns. Also, some cleaners can

produce harmful or unpleasant

fumes if applied to hot surfaces.

Refer to Care Recommendations

on page 17.

SAFETY PRECAUTIONS

10

GAS COOKTOP FEATURES

Available in natural (I2H, I2E and I2E+)

and LP (I3P) gas

Stainless steel top construction

Dual-stacked, sealed burners with auto-

matic reignition on all settings

Individual spark ignition system

Illuminated control panel with two-tiered

control knobs

True Simmer setting on all burners

Low-profile, cast iron continuous burner

grates with matte porcelain finish

Seamless drawn burner pan

CE certified as a Class 3 appliance

Certified for the following appliance

category and adjusted to the gas type and

pressure:

I3P – G31 at 37 mbar

I2E – G20 at 20 mbar

I2E+ – G20/25 at 20/25 mbar

I2H – G20 at 20 mbar

WOLF GAS COOKTOP FEATURES

Model ICBCT15G

Model ICBCT30G

Model ICBCT36G

MODEL ICBCT15G

381 mm Gas Cooktop

Small 3.0 kW

(218 g/h) burners

Low-profile,

continuous grates

Illuminated

control panel

Two-tiered

control knobs

Large 4.9 kW

(356 g/h) burner

Seamless drawn

burner pan

Medium 3.8 kW

(276 g/h) burner

Medium 3.8 kW

(276 g/h) burner

Low-profile,

continuous grates

Small 3.0 kW

(218 g/h) burner

Illuminated

control panel

Two-tiered

control knobs

Seamless drawn

burner pan

381 mm GAS COOKTOP

One medium 3.8 kW (276 g/h) sealed

burner with .2 kW (14.5 g/h) delivered at

simmer

One small 3.0 kW (218 g/h) sealed burner

with .1 kW (7.3 g/h) delivered at simmer

Gas rating: 6.8 kW (NAT) and 494 g/h (LP)

762 mm GAS COOKTOP

One large 4.9 kW (356 g/h) sealed burner

with .2 kW (14.5 g/h) delivered at simmer

One medium 3.8 kW (276 g/h) sealed

burner with .2 kW (14.5 g/h) delivered at

simmer

Two small 3.0 kW (218 g/h) sealed burners

with .1 kW (7.3 g/h) delivered at simmer

Gas rating: 14.7 kW (NAT) and 1069 g/h (LP)

MODEL ICBCT30G

762 mm Gas Cooktop

GAS COOKTOP ACCESSORIES

These optional accessories are available

through your Wolf dealer.

One-piece wok and single burner grate

(Models ICBCT30G and ICBCT36G)

Filler strip

Bracket supports for installation of two

integrated modules with a downdraft

ventilation system (Model ICBCT15G)

High altitude conversion kit

11

WOLF GAS COOKTOP FEATURES

These appliances are certified by Star-K

to meet strict religious regulations in

conjunction with specific instructions

found on www.star-k.org.

Small 3.0 kW

(218 g/h) burners

Low-profile,

continuous grates

Large 4.9 kW

(356 g/h) burner

Illuminated

control panel

Two-tiered

control knobs

Seamless drawn

burner pan

Medium 3.8 kW

(276 g/h) burner

GAS COOKTOP FEATURES

914 mm GAS COOKTOP

One large 4.9 kW (356 g/h) sealed burner

with .2 kW (14.5 g/h) delivered at simmer

One medium 3.8 kW (276 g/h) sealed

burner with .2 kW (14.5 g/h) delivered at

simmer

Three small 3.0 kW (218 g/h) sealed burners

with .1 kW (7.3 g/h) delivered at simmer

Gas rating: 17.7 kW (NAT) and 1287 g/h (LP)

MODEL ICBCT36G

914 mm Gas Cooktop

ACCESSORIES

Optional acces-

sories are available

through your Wolf

dealer.

12

WOLF GAS COOKTOP USE & CARE

CONTINUOUS GRATES

The continuous low-profile cast iron grates of

your gas cooktop are designed for a close fit.

This enables you to move pans easily from

one burner to another without having to lift the

pan or have it tip over between the grates.

Each grate sets securely on dimples on each

corner of the burner pan. Refer to the illustra-

tion below.

For the 762 mm and 914 mm gas cooktops, the

continuous grates are interchangeable with

each other, with the exception of the single

grate on the 914 mm cooktop.

Illuminated

Control Panel

Control panel for Model ICBCT36G

Continuous Grate

Burner Pan

Grate Feet

Continuous grates

ILLUMINATED CONTROL PANEL

The control panel of your gas cooktop is illumi-

nated for instant visual indication that any one

or more burners are in use. It is a safety signal

reminding you that a flame is on and active.

The illustration below shows the control panel

of the 914 mm gas cooktop.

CONTROL KNOBS

Each control knob is positioned to correspond

to the burner regulated.

For the 381 mm and 914 mm cooktops, the

knob on the lower left side regulates the lower

left burner. Conversely, the knob on the upper

right side regulates the upper right burner. The

illustration below shows the configuration of

the control knobs for the 914 mm gas cooktop.

Each knob on the 762 mm cooktop control

panel has a diagram above it. The diagram

shows which burner it regulates.

It is normal for the knobs to be slightly raised

above the surface. This space is an air inlet

necessary for good combustion of gas. Each

knob rests on a valve stem with a rubber

grommet at the base. This design prevents

liquid spills from dripping into the controls

below the burners.

13

DUAL-STACKED BURNER ASSEMBLY

The unique dual-stacked burner design of your

gas cooktop combines all of the burner parts in

one assembly.

After cleaning or removing burner parts for

any reason, it is extremely important that you

reassemble burners correctly.

The burner cap has a groove in the bottom,

which allows the cap to fall into place when

moved around the top of the burner. The cap

should be flat relative to the burner when in

the proper orientation. Failure to do this will

result in a poor flame. Refer to the illustration

below.

SURFACE BURNERS

A spark electrode ignites each surface burner.

This control eliminates the need for continuous

open flame pilots. For added safety and

convenience, each burner is designed with an

electronic reignition system. This feature

enables any burner to relight automatically in

the event it is accidentally extinguished.

A distinguishing feature of Wolf’s low kW

control is its constant, low heat output without

continuous ignitions. The flame diameter

remains full size; only the heat output is

lowered. This patented dual-stacked burner

design makes it possible to enjoy cooking at

full flame as well as maintain control while

simmering at the lowest flame setting.

WOLF GAS COOKTOP USE & CARE

Burner Cap

Igniter

Sealed Burner

Dual-stacked burner assembly

Failure to position the burner parts

correctly could cause flames or gas to

escape, causing heat damage to your

cooktop, or burn between parts, resulting

in poor combustion.

14

CONTROL KNOB OPERATION

Each burner has full flame and full simmer

capabilities. Knobs are designed as two-tiered

”push-to-turn” knobs. One tier is used for

through flame settings; the second tier

controls settings. Refer to the illustra-

tion below. Although this is a child-safe

design, children should never be left unat-

tended in the kitchen when the cooktop is in

use.

To light a burner, push down and turn the

corresponding control knob counterclockwise

to the setting. You will hear a clicking

sound and see the burner ignite. Once the

burner is lit, continue turning the knob

counterclockwise to any one of the settings—

through .

To select a SIMMER setting, turn the burner

knob to the setting; you will feel a stop

detent in the knob rotation. Push down on the

knob, continuing to turn it counterclockwise.

This moves it to the second tier. Now, select

any variation within the SIMMER flame

settings— through .

WOLF GAS COOKTOP USE & CARE

Two-Tiered

Control Knobs

Two-tier burner control knobs

Never leave pans on a setting unat-

tended. Be particularly cautious when

cooking food in fat or grease. It can

become hot enough to ignite.

BEFORE USING YOUR COOKTOP

Before using for the first time, you should

clean your gas cooktop thoroughly with hot

water and a mild detergent. Rinse and dry with

a soft cloth. This removes any residual oil and

grease left on the surface from the manufac-

turing process. Apply a stainless steel polish to

protect the finish and add luster. Refer to Care

Recommendations on page 17.

IMPORTANT NOTE:

Before using your gas

cooktop, check that the surface burner caps are

positioned correctly.

15

FLAME HEIGHT AND APPEARANCE

Select a flame that is just high enough to

maintain the desired cooking speed and is

sized to fit the base diameter of the pan. Never

extend the flame beyond the base of the pan.

The flame on natural gas should be blue with a

deeper blue core. There should be minimal

trace of a yellow flame. A yellow flame indi-

cates an improper mixture of air and gas or

impurities in the gas supply to the range. If

this occurs consistently, call a Wolf authorized

service center to adjust the mixture. With LP

gas, some yellow tipping to the flame is

acceptable and may not require an adjustment.

Refer to the illustration below.

WOLF GAS COOKTOP USE & CARE

Large burner on setting

16

Use the following guidelines when selecting

cookware:

Griddles or open roasters that span two

burners are suitable, providing they are not

warped.

When a large pan is centered over a burner,

the diameter should not exceed 254 mm.

When using pans made of cast iron,

enameled steel or glass ceramic, or coated

with a nonstick finish, select lower flame

settings. High heat applied to such materi-

als will cause ”hot spots,” scorching and

burning.

Cover pans while cooking; covers improve

cooking efficiency. Water boils faster, using

less fuel, and the kitchen stays cooler.

Select high-sided (deep) pans rather than

ones with very wide bases and low sides.

High sides will minimize liquids boiling

over the pan.

Pans with oversize bases that extend

beyond the cooktop frame

should not

be

used. On settings, heat may be

trapped beneath the pan, causing perma-

nent damage to the surface finish.

Use the front burners for larger pans. The

pans are easier to handle, especially when

hot.

Use a wok with a flat bottom.

WOLF GAS COOKTOP USE & CARE

COOKWARE SELECTION

For best results, we recommend medium- to

heavy-weight pans that have a flat base, metal

handle and a good-fitting cover.

Look for pans that are made of materials with

good heat conductivity, such as aluminum and

copper. These metals are sometimes found

”sandwiched” between the inner and outer

layers of the pan. If present, whether visible

from the outside or not, they aid in evenly

conducting heat.

17

CARE RECOMMENDATIONS

COMPONENT CARE RECOMMENDATION

Exterior Surface

Stainless steel

Burner Pan

Stainless steel

CAUTION:

Make sure the gas cooktop is off and all surfaces are cool before

cleaning any part of the cooktop.

Although stainless steel is resistant to most stains, it is not totally

impervious to damage. Salt and some cooking liquids may pit and stain the

surface. Always remove these spills immediately.

General care:

Use a clean cloth or sponge; wipe with warm water and a mild

dish detergent. Rinse and dry immediately.

Exterior finish:

To clean the exterior of a classic or platinum stainless steel

model, use a soft, nonabrasive stainless steel cleaner and apply with a soft,

lint-free cloth.

Spray degreasers:

Spray on a cloth and wipe surface to remove fingerprints

and greasy spatters. Buff dry immediately to avoid streaking.

Hard water stains:

Use white vinegar and water.

Do not use abrasive cleaners; they will permanently scratch the surface.

Do not use steel wool pads.

Cool first. Wash in warm water and liquid detergent or mild abrasive cleaner.

Foods high in acid or sugar content, such as milk, tomatoes, sauerkraut, fruit

juices or pie filling, may pit or craze the surface. Remove as soon as possible

before heating again.

Never wipe a warm or hot porcelain surface with a damp sponge; it may

cause chipping or crazing (tiny hairlike cracks).

Remove from cooktop and place on a flat surface near the sink to clean.

Nonabrasive cleaners:

Hot water and liquid detergent or a paste of baking

soda and water; use a plastic pad or sponge.

Mild abrasive and abrasive cleaners:

Use sparingly.

To remove, slip the edge of a dish towel under the knob; pull edges together.

Using the towel for leverage, lift up, pulling the knob off the valve stem.

General care:

Wipe each knob with damp cloth and mild soap and water;

rinse and dry. Never soak or use abrasive cleaners; they will scratch the

finish and remove the markings.

Spray cleaners:

Removes fingerprints and greasy food soils. Spray first on

a cloth before wiping panel.

Keep dry; never spray water or cleaner directly on the igniter. When cleaning

around the surface burner, be careful that the cloth does not catch on the

igniter and damage it.

Burner Cap

Porcelain enamel

Burner Grates

Porcelain-coated

cast iron

Control Knobs

Chrome-plated

Control Panel

Tempered glass

Spark Igniters

Ceramic

WOLF GAS COOKTOP USE & CARE

18

COOKTOP CLEANING TIPS

Wait until surfaces are cool before cleaning.

For best results, wipe up spills and spatters

as they occur and immediately after the

cooktop has cooled. If splatters are allowed

to cook on, they may permanently damage

or stain the finish.

If in doubt about using one of your

cleaners, check the label. To check if it is

safe to use on your cooktop, try a small

amount on an inconspicuous area using

very light pressure.

Use caution when spraying cleaners. Some

contain caustic ingredients that can damage

adjacent parts and finishes. Protect the

adjacent parts by masking them off so that

the overspray is contained to the finish

being cleaned.

Do not spray cleaners on electrical controls,

igniters, wires or knob valve stems.

WOLF GAS COOKTOP USE & CARE

STAINLESS STEEL FINISH

For the stainless steel exterior finish, use a

soft, nonabrasive stainless steel cleaner and

apply with a soft lint-free cloth.

To bring out the natural luster of both

finishes, lightly wipe the surface with a

water-dampened microfiber cloth, followed

with a dry microfiber cloth. All work should

follow the grain direction of the finish.

Better results are obtained by keeping the

cloth in continuous contact with the metal.

Under no circumstances should you use a

metallic or highly abrasive cleaner or cloth,

as this will permanently scratch the surface.

DO NOT use abrasive cleaners on your

cooktop; they will permanently scratch

the surface.

19

WOLF TROUBLESHOOTING GUIDE

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE SOLUTION

Burner flame does not

Reposition the burner cap of the stacked sealed burner assembly

burn evenly

as described on page 13.

Placement of pan on the grate is not centered above the burner.

Pan material does not conduct heat evenly.

Base of pan is warped and does not rest flat on the grate or handle

of pan is too heavy and tips pan toward handle.

Countertop or cooktop cabinet is not level.

Burner fails to ignite

Ceramic igniter is damp from a spillover or spray cleaner. Allow

ceramic to dry out completely.

Burner head ports are blocked. Use a straightened, metal paper

clip to open the blockage.

If a GFCI circuit is used, check to see if it has been tripped.

Burners extinguish them-

Good gas combustion requires the correct amount of airflow to

selves when using more

maintain the flame. Using two oversize pans simultaneously

than one large roaster or

restricts air movement.

griddle simultaneously

Food boils out of the pan

Heat setting is too high or pan size is too small for its contents.

and overflows into the

burner pan

Water does not come to

Water temperature is colder than usual.

a boil fast enough

Cover pan for most efficient use of the setting.

Diameter of pan is too large or base of pan is warped.

Food cooks too slowly

Too much food is added at one time; reduce amount of food and

when sautéing

sauté in batches.

Size of food pieces is too large or temperature of food is colder

than usual.

Pan does not conduct heat evenly.

Simmer setting does not

Delicate foods may need a lower simmer setting so that scorching

maintain constant surface

does not occur.

bubbles

Food boils or burns in

one area of the pan and

not the other

20

SERVICE INFORMATION

When requesting information, literature,

replacement parts or service, always refer to

the model and serial number of your cooktop.

Both numbers are listed on the product rating

plate located on the underside of the cooktop.

Refer to the illustration on page 5. Record

the rating plate information below for future

reference.

Model Number

Serial Number

Installation Date

Wolf Dealer and Phone

BEFORE CALLING FOR SERVICE

Before calling your Wolf dealer or regional

distributor, refer to the Troubleshooting Guide

on page 19. Check the household fuse or

circuit breaker to see if it has been blown or

tripped and that the electrical connection to

the appliance has not been disconnected. A

power outage may also have caused a disrup-

tion in service.

WOLF SERVICE INFORMATION

CONTACT

INFORMATION

Website:

wolfappliance.com

The information and images in this book are the

copyright property of Wolf Appliance, Inc., an

affiliate of Sub-Zero, Inc. Neither this book nor

any information or images contained herein may

be copied or used in whole or in part without the

express written permission of Wolf Appliance,

Inc., an affiliate of Sub-Zero, Inc.

La page est en cours de chargement...

Sub-Zero ICBCT30G Manuel utilisateur

Ce manuel convient également à

Sub-Zero ICBCT30G Manuel utilisateur

dans d''autres langues

Autres documents