Kenmore 66513349K606 Guide d'installation

Marque: Kenmore

Modèle: 66513349K606

Taper: Guide d'installation

Ce manuel convient également à

INSTALLATION INSTRUCTIONS

DRAWER DISHWASHER

INSTRUCCIONES DE INSTALACION

DE LA LAVAVAJILLAS DE CAJON

INSTRUCTIONS D'INSTALLATION

LAVE-VAISSELLEA TIROIR(S)

Table of Contents/indite/Table des mati&res ........................................................................................... 2

iMPORTANT:

Save for local electrical inspector's use.

JnstaJJer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

IMPORTANTE:

Guarde para tenerlas a disposici6n del inspector de electricidad local.

Instalador: Deje las instrucciones de instalaci6n con el propietario.

Propietario: Conserve las instrucciones de instalaci6n para referencia futura.

iMPORTANT :

Conserver pour consultation par I'inspecteur local des installations 61ectriques.

Installateur : Remettre les instructions d'installation au propri6taire.

Propri6taire : Conserver les instructions d'installation pour r6f6rence ult6rieure.

W10296154B

TABLEOF CONTENTS

DISHWASH ER SAFETY ......................................................................................... 3

INSTALLATION REQUIREMENTS ......................................................................... 4

Tools and Parts .................................................................................................................. 4

Location Requirements ..................................................................................................... 5

Water Supply Requirements ........................................................................................... 5

Electrical Requirements .................................................................................................... 6

Drain Requirements ........................................................................................................... 6

INSTALLATION INSTRUCTIONS .......................................................................... 7

Unpack Dish Drawer ......................................................................................................... 7

Prepare Cabinet Opening ............................................................................................... 7

Prepare Dishwasher ........................................................................................................... 8

Route Electrical Wiring .................................................................................................... 9

Route Water Supply Line and Drain Hose ................................................................. 10

Connect Water Supply Line and Drain Hoses............................................................ 11

Make Electrical Connection ........................................................................................... 12

Install Trim Pieces and Level Dishwasher .................................................................... 13

Secure the Dish Drawers ................................................................................................ 15

Complete Installation ...................................................................................................... 15

JNDICE

SEGURIDAD DE LA LAVAVAJILLAS ................................................................... 17

REQUISITOS DE INSTALACION .......................................................................... 18

Piezas y herramientas ...................................................................................................... 18

Requisitos de ubicaci6n ................................................................................................... 19

Requisitos del suministro de agua ................................................................................. 19

Requisitos el_ctricos ........................................................................................................ 20

Requisitos de desagLie .................................................................................................... 20

INSTRUCCIONES DE INSTALACION .................................................................. 21

Desempaque el caj6n para platos ................................................................................ 21

Prepare ]a abertura de] armario .................................................................................. 21

Prepare la lavavajillas .................................................................................................... 22

Dirija el cableado el_ctrico ........................................................................................... 23

C6mo dirigir la linea de suministro de agua y la manguera de desagiJe ........... 24

Conecte la linea de suministro de agua y las mangueras de desagiJe ................25

Conexi6n del suministro el_ctrico ................................................................................ 27

Instale las piezas del marco y nivele la lavavajillas ................................................ 28

Asegure la lavavajillas ................................................................................................... 29

Complete la instalaci6n ................................................................................................. 30

TABLEDESMATIERES

SI_CURITI_ DU LAVE-VAISSELLE .......................................................................... 31

EXIGENCES D'INSTALLATION ........................................................................... 32

Outillage et composants ................................................................................................ 32

Exigences d'emplacement ............................................................................................. 33

Specifications de I'alimentation en eau ...................................................................... 33

Specifications _lectriques .............................................................................................. 34

Exigence d'_vacuation ................................................................................................... 34

INSTRUCTIONS D'INSTALLATION .................................................................... 35

D@ballage du lave-vaisselle .......................................................................................... 35

Am_nagement de la cavit_ d_encastrement du placard ......................................... 35

Preparation du lave-vaisselle ........................................................................................ 36

Installation du c6blage _lectrique ............................................................................... 37

Acheminement du conduit d'alimentation en eau et du tuyau de vidange .........38

Raccordement du conduit d'alimentation en eau et des tuyaux de vidange ......39

Raccordement du circuit _lectrique ............................................................................ 40

Installation des pi_ces de garniture; _tablissement de I'aplomb

du lave-vaisselle .............................................................................................................. 42

Arrimage du lave-vaisselle ........................................................................................... 43

Achever I'installation ...................................................................................................... 44

DISHWASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using the dishwasher, follow basic precautions, including the following:

• Read all instructions before using the dishwasher.

• Use the dishwasher only for its intended function.

• Use only detergents or rinse agents recommended for use

in a dishwasher, and keep them out of the reach of children.

• When loading items to be washed:

1) Locate sharp items so that they are not likely to damage

the door seal; and

2) Load sharp knives with the handles up to reduce the risk

of cut-type injuries.

• Do not wash plastic items unless they are marked

"dishwasher safe" or the equivalent. For plastic items not so

marked, check the manufacturer's recommendations.

• Do not touch the heating element during or immediately

after use.

• Do not operate the dishwasher unless all enclosure panels

are properly in place.

[] Do not tamper with controls.

[] Do not abuse, sit on, or stand on the door, lid, or dish racks

of the dishwasher.

[] To reduce the risk of injury, do not allow children to play in

or on the dishwasher.

[] Under certain conditions, hydrogen gas may be produced in

a hot water system that has not been used for two weeks or

more. HYDROGEN GAS IS EXPLOSIVE. If the hot water

system has not been used for such a period, before using

the dishwasher turn on all hot water faucets and let the

water flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is flammable,

do not smoke or use an open flame during this time.

[] Remove the door or lid to the washing compartment

when removing an old dishwasher from service or

discarding it.

SAVE THESE INSTRUCTIONS

Tip Over Hazard

Do not open dishwasher drawer until dishwasher is inside the cabinet opening.

if the dishwasher is not in the cabinet opening, slowly open the drawer while someone grasps

the rear of the dishwasher.

Failure to follow these instructions can result in death or serious injury.

You need to:

• Slowly open dishwasher drawer while someone grasps the rear of the

dishwasher. Remove shipping materials. Close dishwasher drawer.

Latch the dishwasher drawer shut.

• Observe all governing codes and ordinances.

• Install this dishwasher as specified in these instructions.

• Have everything you need to properly install dishwasher.

• Contact a qualified installer to ensure that dishwasher is installed to

meet all electrical and plumbing national and local codes and

ordinances.

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation. Read and

follow the instructions provided with any tools listed here.

Tools Needed

• Pliers

• Phillips screwdriver

• Flat-blade screwdriver

• 3/le" and 1/4" nut drivers or hex

sockets

• Measuring tape or ruler

• 11/2'' hale saw bit

• 10" adjustable wrench

• Utility knife

• Level

• Cordless drill

• 1/8" drill bit

• Security T-20 TORX ®f driver (on

some models)

Parts Needed

A. 72" (182.9 cm) flexible water supply line

B. Zip tie

C. Appropriate sized UI Listed wire connectors _2)

1-®TORX is a registered trademark of Acument Intellectual Properties, LLC

Parts Supplied

Check that all parts are included.

A ..............

A. 3/4" UL / isted/CSA Approved strain

re//ef

B, ].25" hose c/amp

C. Mounting bracket screws _8)

D, Unit mounting screws _4)

E. Drain hose connector

F, Mounting brackets _4t)

6;. Drain connector spring clamps _2]

_ C

j ..........

H. Trim strips (2)

L Toe kick brackets (2)

], Toe kick bracket screws (2)

K. Toe kick trim

L. Pane/fasteners (on some mode/s) (2)

A4. TOR._ _ screws (on some mode M (I0)

N. Drain hose

IMPORTANT: Observe all governing codes and ordinances. Failure to meet

codes and ordinances could lead to fire or electrical shock.

Proper installation is your responsibility.

• Contact a qualified installer to ensure that the dishwasher is installed

to meet all electrical and plumbing national and local codes and

ordinances.

• Install the dishwasher as specified in these instructions.

• Have everything you need to properly install dishwasher.

• Keep the dishwasher and water lines leading to dishwasher from

freezing. Damage from freezing is not covered by the warranty.

• This dishwasher is manufactured for indoor use only.

• Install and level dishwasher on a floor that will hold the weight, and in

an area suitable for its size and use.

Product Dimensions

24,, 23 ,,

(61cm)

333/4'`

(85.7cm)

48.9 cm)

11/2"

(3.75 cm)

Installation Clearances

Cutout Dimensions

24"

(61cm)

.3s/4"

Preferred Utility Area

A. Choose/eft-hand or fight-hand water connection route.

B. Choose/eft-hand or fight-hand e/ectfic connection and drain route,

NOTE: All holes should be drilled at 11/2'' (3.8 cm) diameter.

• A hot water line with 20 to 120 psi (138 to 862 kPa) water pressure.

• 120°F (49°C) water temperature at dishwasher.

• Flexible braided fill line (1/2" minimum plastic tubing is not

recommended).

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

[]

GROUNDING iNSTRUCTiONS

For a grounded, cord-connected dishwasher:

The dishwasher must be grounded. In the event of a

malfunction or breakdown, grounding will reduce the

risk of electric shock by providing a path of least

resistance for electric current. The dishwasher is

equipped with a cord having an equipment-grounding

conductor and a grounding plug. The plug must be

plugged into an appropriate outlet that is installed and

grounded in accordance with all local codes and

ordinances.

WARNING: Improper connection of the

equipment-grounding conductor can result in a risk of

electric shock. Check with a qualified electrician or

service representative if you are in doubt whether the

dishwasher is properly grounded. Do not modify the

plug provided with the dishwasher; if it will not fit the

outlet, have a proper outlet installed by a qualified

electrician.

For a permanently connected dishwasher:

The dishwasher must be connected to a grounded

metal, permanent wiring system, or an equipment-

grounding conductor must be run with the circuit

conductors and connected to the equipment-

grounding terminal or lead on the dishwasher.

SAVE THESE iNSTRUCTIONS

Contact a qualified electrician.

Ensure that the electrical installation is adequate and in conformance with

all national and local codes and ordinances.

You must have:

• 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply.

• Copper wire only.

We recommend:

• A time-delay fuse or circuit breaker.

• A separate circuit.

If direct wiring dishwasher:

• Use flexible, armored or nonmetallic sheathed, copper wire with

grounding wire that meets the wiring requirements for your home and

local codes and ordinances.

• Use strain relief method provided with house wiring junction box or

install a UL Listed/CSA Approved clamp connector to the house wiring

junction box. If using conduit, use a UL Listed/CSA Approved conduit

connector.

If connecting dishwasher with a power supply cord:

• Use Power Supply Cord Kit (Part Number 4317824) marked for use

with dishwashers. Kit contents include:

• Voltex, Inc., UL Listed 16-gauge 3 wire power supply cord with

3 prong grounded plug.

• Neer C-500 z/8"strain relief.

• 3 wire connectors.

• Part Number 302797 grommet.

Follow the kit instructions for installing the power supply cord.

Power supply cord must plug into a mating three prong, grounded

outlet, located in the cabinet next to the dishwasher opening. Outlet

must meet all local codes and ordinances.

IMPORTANT: If you plan to install a garbage disposer, an additional

separate 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply is

required.

Use the new drain hose supplied with your dishwasher. If this is not

long enough, use a new drain hose with maximum length of 12 ft

(3.7 m) that meets all current AHAM/IAPMO test standards, is

resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector

of the dishwasher.

Connect drain hose to waste tee or disposer inlet above drain trap in

house plumbing and 20" (50.8 cm) minimum above the floor. It is

recommended that the drain hose either be looped up and securely

fastened to the underside of the counter, or be connected to an air

gap.

Drain Air Gap

Use a drain air gap if the drain hose is connected to house plumbing

lower than 20" (50.8 cm) above the subfloor or floor.

Use 1/2" (1.3 cm) minimum I.D. drain line fittings.

INSTALLATION INSTRUCTIONS

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Turn off water supply.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

1. Read valuable ;nformatlon on exterior of shipping box before

opening.

2. Remove shipping materials, tape and film from the dishwasher.

Remove parts package from inside the dishwasher.

To ensure minimum clearance dimensions exist:

• Measure the distance from the cabinet countertop to the floor and

ensure 333/4" (85.7 cm) minimum height.

• Measure the distance from the front of the cabinet to the back

wall and ensure 24" (61 cm) minimum depth.

• Measure the distance from the left-hand side to the right-hand

side of opening and ensure 24" (61 cm) minimum width.

2. Drill 11/2'' (3.8 cm) diameter holes for drain and water hoses and

electrical wiring as shown. Holes should be placed 1/2" (1.3 cm) from

back wall.

(1.3cm)

A. Choose/eft-hand or right-hand water hose route.

B. Choose/eft-hanc/or right-hanc/ e/ectric wire anc/ drain route,

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet (Part Number 302797, provided

with cord kit).

3. Install mounting brackets 17" (43.2 cm) from floor using screws

provided. If needed, drill 1/8" pilot holes in cabinet.

17"

(43,2 cm)

4. Decide which dishwasher-to-counter attachment method will be used.

Option1: Solid Surface Countertop Installation

• Install second set of mounting brackets 33t/2" (85 cm) from floor. If

needed, drill 1/8" pilot holes in cabinet.

Option 2: Wood Countertop Installation

• Prepare dishwasher by folding over tabs located on the top front

as shown.

Tip Over Hazard

Do not open dishwasher drawer until dishwasher is

inside the cabinet opening.

if the dishwasher is not in the cabinet opening, slowly

open the drawer while someone grasps the rear of the

dishwasher.

Failure to follow these instructions can result in death

or serious injury.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

1. Measure cabinet opening height from floor to bottom of countertop.

2. Using two or more people, place corner packaging on the floor and

place dishwasher on its back.

3. Adjust leveling legs based on the cabinet opening measurement and

the chart below.

m i

i I

i A

I iX

! v

33_ " (85.7 cm)

34" (86.3 cm)

34_ " (86.7 cm)

34_" (87 cm)

34_ " (87.3 cm)

: 0 I'

: _ " (0.3 cm)

: _ " (0.6 cm)

:_" (I cm)

: 1/2"(I.3 cm)

34_" (87.6 cm)

345_" (87.9 cm)

34_/4" (88.3 cm)

34_" (88.6 cm)

35" (88.9 cm)

Place dishwasher in upright position.

:5_,, (L6 cm]

:_ " (L 9 cm]

:_" (2.2 cm)

:I" (2.5 cm)

:I_" (2.9 cm,)

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

Follow all national and local codes and ordinances for completing

electrical supply to cabinet.

Option 1: Right-Hand Side Utility Route

Route wire through 11,/2" (3.81 cm) hole located 8" (20.32 cm) above the floor.

After routing the electrical wire through the right-hand hole, attach the

wire to back left-hand side of cabinet wall 8" (20.32 cm) above the floor.

Then continue routing the wire along the left-hand side of cabinet opening

to the front of the opening.

Option 2: Left-Hand Side Utility Route

Route wire through 11,/2"(3.81 cm) hole located 8" (20.32 cm) above the floor.

After routing the electrical wire through the left-hand hole, continue routing

the wire along the left-hand side of cabinet to the front of the opening.

Connect water supply line to water valve on dishwasher. Option 1: Right-Hand Side Utility Access

• For right-hand routing, place the water supply line in the clips.

Slide clamp onto drain hose, and then push hose into "Y" connector

until it is fully seated. Several clicks will be heard.

3. Slide clamp into position over the "Y" connector.

• Route drain hose on clips on bottom/back of unit.

Option 2: Left-Hand Side Utility Access

• For left-hand routing, place hose in clip on bottom right-hand side

of the dishwasher.

)

)(

• Route water supply line and drain hoses into the cabinet.

Slide dishwasher partway into the cabinet opening. Allow for

access to the electrical terminal box.

Connect water supply line to the water valve under the sink.

A. Hot water supply

2. Slide clamps onto drain hoses (Figure A). Do not cut drain hoses.

3. Push hose into drain connector until fully seated (Figure B). Several

"clicks" will be heard.

4. Slide clamp into position (figures C and D).

5. Connect the drain hose using one of the following options:

Option 1: Waste Disposer, No Drain Air Gap

......B

A. For new construction t remove disposer plug.

B. Connect drain connector to waste disposer.

C, Tighten clamp,

NOTE: This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where the dishwasher will be installed. It is

recommended that the drain hose be looped up and securely fastened to

the underside of the counter.

Option 2: No Waste Disposer and Drain Air Gap

A. Drain air gap

B. Drain hose connector

C, VVaste

Option 3: Waste Disposer and Drain Air Gap

A .................................

A. Drain air gap

B. Drain hose connector

C, VVaste

Option 4: No Waste Disposer, No Drain Air Gap

A. Drain hose connector

B. Waste

NOTES:

• Attach the drain hose connector to the water waste line using the

supplied hose clamp.

• This connection must be before the drain trap and at least 20"

(50.8 cm) above the floor where the dishwasher will be installed. It

is recommended that the drain hose be looped up and securely

fastened to the underside of the counter.

6. Turn on water and check for leaks.

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

1. Remove screw securing the electrical box cover. Remove cover.

2. Route electrical wires through strain relief and secure to electrical

plate.

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Connect wires as follows using twist-on connectors sized to connect

direct wire to 16 gauge dishwasher wire.

Power supply wire: Terminal box wire:

white white

black black

ground wire -_r----------_ ground connector

4. Attach ground wire to the green ground screw.

A. Attach ground wire to green screw,

B. Attach whffe and Mack wires.

5o Reinstall electric box cover with all wires contained inside the terminal

box.

NOTE: Do not plug into outlet until instructed to do so.

Open bottom drawer.

Push in clips and slide rails back 5" (12.7 cm).

3. Lift drawer off slide rails. Place drawer off to the left on covering.

Slide rails into dishwasher.

4. Slide the dishwasher into position in the cabinet opening. Check that

the drain hose and electrical wiring are not kinked.

5. Check left to right level by placing the level on the top of the drawer.

Check front to back level by placing level on the slide rails.

.J:

6. Adjust legs with a 3A6" socket wrench to level the dishwasher.

A. Adjust logs.

Rest trim strip on floor and mark trim at the top of the frame flange

height. Pick the closest groove to the mark. If the mark is between

2 grooves, choose the groove that makes the trim strip the shortest. On

a covered surface, cut the trim strip at the selected groove. Pull

dishwasher back out of cabinet opening about 6" (15.24 cm).

B. Attach the toe kick bracket to the frame.

9. Place trim strip into toe kick bracket.

10. Attach toe kick bracket on the opposite side.

11. Place flexible side trim strips on both sides as shown.

12. Slide the dishwasher back into position in the cabinet opening. Check

that the drain hose and electrical wiring are not kinked.

Remove top drawer (same procedure as followed to remove bottom

drawer) and set drawer on bottom drawer separated with corner

packaging.

Attach dishwasher to the lower cabinet mounting bracket (installed

earlier).

A. Attach dishwasher to lower cabinet mounting bracket.

3. Attach dishwasher to upper cabinet mounting brackets.

Option I: Solid surface counterl_p

Attach dishwasher to the side cabinet mounting brackets (installed

earlier).

A. Attach dishwasher to side cabinet mounting brackets.

Optlon 2: Wood countertop

Attach the dishwasher to the countertop using the folded over

mounting tabs located on the top of the dishwasher.

A. Attach dishwasher to countertop using folded over mounting tabs.

1. Pull top drawer slide rails out and set top drawer on slide rails.

2. Pull slide rails forward until they snap into position.

3. Push top drawer in and repeat above steps for bottom drawer.

4. In the cabinet under the sink, coil excess drain hose and wrap with a

zip tie.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death_

fire_ or electrical shock.

5. Plug in dishwasher or reconnect the power.

Select the Rinse Only cycle and press START/RESUME. Allow the

dishwasher to fill, rinse and drain. Check for leaks. If leaks are found,

secure the connection and repeat this step.

If you need Assistance or Service:

Please reference the "Assistance or Service" section of the User Instructions

or contact the dealer from whom you purchased your dishwasher.

SEGURIDAD DE LA LAVAVAJILLAS

Su seguridad y la seguridad de los demos es muy importante.

Hemos incluido muchos mensajes importantes de seguridad en este manual yen su electrodomestico. Lea y obedezca siempre

todos los mensajes de seguridad.

Este es el simbolo de advertencia de seguridad.

Este simbolo le llama la atenci6n sobre peligros potenciales que pueden ocasionar la muerte o una lesi6n a

usted y a los demas.

Todos los mensajes de seguridad iran a continuaci6n del simbolo de advertencia de seguridad y de la palabra

"PELIGRO" o "ADVERTENCIA". Estas palabras significan:

Si no sigue las instrucciones de inmediato, usted puede

morir o sufrir una lesibn grave.

Si no sigue las instrucciones, usted puede morir o sufrir

una lesibn grave.

Todos los mensajes de seguridad le diran el peligro potencial, le diran c6mo reducir las posibilidades de sufrir una lesi6n y Io que

puede suceder si no se siguen las instrucciones.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

ADVERTENCIA: Cuando use la lavavajillas siga precauciones basicas, incluyendo las siguientes:

• Lea todas las instrucciones antes de usar la lavavajillas.

• Use la lavavajillas 0nicamente para las funciones que fue

dise_ada.

• Use 0nicamente detergentes o agentes de enjuague

recomendados para ser usados en las lavavajillas y

mantengalos fuera del alcance de los ni_os.

• AI introducir los artfculos para lavar:

1) Coloque los artfculos puntiagudos de manera que no

da_en el sello de la puerta

2) Introduzca los cuchillos filosos con los mangos hacia

arriba para reducir el riesgo de cortaduras.

• No lave artfculos de plastico que no Ileven la indicaci6n

"lavables en la lavavajillas" u otra similar. Lea las

recomendaciones del fabricante para los artfculos de

plastico que no Ileven tal indicaci6n.

• No toque el elemento de calefacci6n durante o

inmediatamente despues de usar la lavavajillas.

[] No haga funcionar la lavavajillas a menos que todos los

paneles esten colocados debidamente en su lugar.

[] No juegue con los controles.

[] No abuse, ni se siente ni se pare sobre la puerta, la tapa o

sobre las canastas de la lavavajillas.

[] Para reducir el riesgo de lesi6n, no permita que los ni_os

jueguen dentro ni sobre la lavavajillas.

[] Bajo ciertas condiciones, un sistema de agua caliente que

no ha sido usado por dos semanas o mas puede producir

gas hidr6geno. EL GAS HIDROGENO ES EXPLOSlVO. Si

el sistema de agua caliente no ha sido usado por ese

perfodo, abra todas las Ilaves de agua caliente y deje que

corra el agua por varios minutos antes de usar la

lavavajillas. Esto permitira que los gases acumulados

escapen. Debido a que el gas es inflamable, no fume ni

encienda ninguna llama abierta durante este tiempo.

[] Quite la puerta o la tapa del compartimiento de lavado

cuando remueva o deje de usar para siempre una vieja

lavavajillas.

GUARDE ESTAS INSTRUCCIONES

Peligro de Vuelco

No abra el caj6n de la lavavajillas hasta que la misma est6 dentro de la abertura del armario.

Si la lavavajillas no est_ dentro de la abertura del armario, abra lentamente el caj6n mientras

alguien sostiene la parte posterior de la lavavajillas.

No seguir estas instrucciones puede ocasionar la muerte o heridas serias.

Usted necesita:

• Abrir despacio el caj6n de la lavavajillas mientras otra persona agarra la

parte posterior de la lavavajitlas. Quite el material de transporte. Cierre el

caj6n de la lavavajitlas. Cierre y asegure el caj6n de la lavavajitlas.

• Observar todos los c6digos y regtamentos aplicables.

• Instalar esta lavavajillas como se especifica en estas instrucciones.

Tener todo Io necesario para instalar la lavavajillas adecuadamente.

Ponerse en contacto con un instalador calificado para asegurarse de que

la lavavajillas haya sido instalada de manera que cumpta con todos los

c6digos y ordenanzas el_ctricos y de plomerfa nacionales y locales.

REQUISITOS DE INSTALACION

ReOna las herramientas y piezas necesarias antes de comenzar la

instalaci6n. Lea y siga las instrucciones provistas con cualquiera de las

herramientas enlistadas aquf.

Herramientas necesarias

• Pinzas

• Destornillador Phillips

• Destornillador de hoja plana

• Llave de tuercas o Ilave de tuba

hexagonal de 3/16" y 1/4".

• Cinta de medir o regla

• Broca de sierra perforadora

de 11/2''

• Llave de tuercas ajustable de

10"

• Cuchillo para usa general

• Nivel

• Taladro inal6mbrico

• Broca de 1/8"

• Destornillador de seguridad

T-20 TORX ®f (en algunos

modelos)

Piezas necesarias

A. I /nea de sumin/stro de agua flexible de 72" (182t9 cm)

B. Atadura

C. Conectores de tamafio aprop/ado para cables que se encuentren en

la l/sta de UL (2)

Piezas suministradas

Verifique que est&n todas las piezas.

M_. ,¸ _ '

A. Protector de cables de 3_, que est# en H.

/a /ista de UZ/certif/cado par CSA /.

B. Abrazadera para manguera de 1,25"

C. Tornillos para los soportes de J.

montaje (8)

D. 1-ornH/os de montaje para /a /(.

unidad (4) Z.

E. Conector de/a manguera de desagiJe

F. 5oportes de montaje (4) A4.

G. Abrazaderas t/po resorte para el

conector gel desagiJe (2) N.

Tiras de adorno (2)

Soportes para la cubierta

protectora (2)

Tornillos para el soporte de/a

cub/erta protectora (2)

Adorno para /a cub/erta protectora

Sujetadores para panel (en algunos

modelos) (2 2

Torn/llos 7-ORX _ (en a/gunos

modelos) (I0)

A4anguera de desagOe

IMPORTANTE: Observe todos los c6digos y reglamentos aplicables. Si no

se siguen los c6digos y ordenanzas, esto podrfa hacer que se produzca un

incendio o choque el_ctrico.

La instalaci6n correcta es su responsabilidad.

• P6ngase en contacto con un instalador calificado para asegurarse que

la lavavajillas haya sido instalada de manera que cumpla con todos

los c6digos y ordenanzas el_ctricos y de plomerfa nacionales y

locales.

• Instale la lavavajillas como se especifica en estas instrucciones.

• Tenga todo Io necesario para instalar la lavavajillas adecuadamente.

• Evite los da_os ocasionados por congelamiento a la lavavajillas y a

las Ifneas de agua que van a la misma. Los da_os ocasionados por

congelamiento no est6n cubiertos bajo la garanfia.

• Esta lavavajillas fue fabricada Onicamente para uso en interiores.

• Instale y nivele la lavavajillas en un piso que pueda soportar su peso y

en un 6rea adecuada para su tama_o y uso.

Medidas del producto

333/4"

(85,7 cm)

91/4,, 11/2"

,gcm) (3,75 cm)

Espacios libres para la instalaci6n

Dimensiones de corte

24"

(61cm)

337/8''

//urea de servicio preferida

(( m)

A. Elija una rufo hacia /o derecha o hacia /o izquierda para /o conexidn

de/agua.

B. Ellja una ruta hac/a la derecha o hac/a la izquierda para la conex/dn

eldctrica y de/desagUe.

NOTA: Todos los orificios deben ser taladrados con un di6metro de 11/2''

(3,8 cm).

• Una tuberia de agua caliente con presi6n de agua de 20-120 Ib/pulg 2

(138-862 kPa).

• Temperatura del agua en la lavavajillas de 120°F (49°C).

• Linea de Ilenado flexible trenzada (no se recomienda una tuberfa de

pl6stico de un minimo de 1/2").

Peligro de Choque El_ctrico

Conecte a un contacto de pared de conexi6n a tierra de

3 terminales.

No quite la terminal de cone×i6n a tierra.

No use un adaptador.

No use un cable el_ctrico de extensi6n.

No seguir estas instrucciones puede ocasionar

la rnuerte, incendio o choque el_ctrico.

INSTRUCCIONES DE

CONEXION A TIERRA

• Para una lavavajillas con cable el_ctrico y cone×i6n a

tierra:

La lavavajJllas debe estar conectada a tierra. En caso de

funcionarniento defectuoso o averia, la conexi6n a tierra

reduce el riesgo de choque electrico al establecer una

ruta de rnenor resistencia para la corriente electrica. La

lavavajJllas viene equipada con un cable electrico que

tiene un conductor para conexJ6n a tierra y un enchufe

con conexi6n a tierra. El enchufe debe ser conectado a

un contacto apropiado que este instalado y conectado a

tierra de acuerdo con todos los c6digos y ordenanzas

locales.

ADVERTENCIA: La conexi6n inadecuada del

conductor de conexi6n a tierra puede resultar en riesgo

de choque electrico. Pregunte a un electricista calificado

o a un agente de servicio si no est,, seguro si la

lavavajillas esta adecuadamente conectada a tierra. No

modifique el enchufe que viene con la lavavajillas. Si no

cabe en el contacto, pida que un electricista calificado

instale un contacto apropiado.

• Para lavavajillas con conexi6n permanente:

Esta lavavajJllas debe estar conectada a un sisterna de

cableado de metal perrnanente, conectado a tierra, o se

debe tender un conducto para la conexi6n a tierra del

equipo con los conductores de circuito y conectado a la

terminal de tierra del equipoo al conductor de surninistro

de la lavavajillas.

GUARDE ESTAS INSTRUCCIONES

P6ngase en contacto con un electricista calificado.

Aseg6rese que la conexi6n el6ctrica sea adecuada y de conformidad con

todos los c6digos y ordenanzas locales y nacionales.

Usted debe tener:

• Un suministro el&ctrico de 120 voltios, 60 hertzios, CA solamente, de

15 6 20 amperios y protegido con fusible.

• Solamente alambre de cobre.

Recomendamos:

• Un fusible retardador o un cortacircuitos.

• Un circuito separado.

Si va a hacer un cableado directo para la lavavajillas:

• Use alambre de cobre blindado flexible o forrado no met61ico con el

alambre de puesta a tierra, el cual cumpla con los requisitos de

cableado para su casa y con los c6digos y ordenanzas locales.

• Use el m6todo de protector de cables provisto con la caja de

empalmes del cableado de la casa, o instale un conector tipo

abrazadera que est& en la lista de UL/certificado por CSA, a la caja

de empalmes del cableado de la casa. Siva a usar un conducto,

utilice un conector de conducto que est6 en la lista de UL/certificado

por CSA.

Si va a conectar la lavavajillas con un cable de suministro eE_-trico:

• Use el juego del cable de suministro el&ctrico (pieza N ° 4317824), que

est6 marcado para usarse con lavavajillas. El juego incluye:

• Cable de suministro el&ctrico de 3 hilos, calibre 16, en la lista de

UL, marca Voltex, Inc. con un enchufe con conexi6n a tierra de

3 hilos.

• Protector de cables marca Neer C-500 de %"

• Conectores para 3 hilos.

• Aro de refuerzo pieza N ° 302797

Para la instalaci6n del cable de suministro el_ctrico, siga las

instrucciones del juego.

El cable de suministro el_ctrico debe conectarse a un contacto

apropiado de pared de 3 terminales, con conexi6n a tierra, ubicado

en el armario que se encuentra al lado de la abertura de la

lavavajillas. El contacto debe cumplir con todos los c6digos y

ordenanzas locales.

IMPORTANTE: Si planea instalar un recipiente de desechos, se requiere

tener un suministro el_ctrico separado adicional, de 120 voltios, 60 Hz, CA

solamente, de 15 6 20 amperios, con fusible.

• Use la manguera nueva de desagiJe provista con su lavavajillas. Si no

es Io suficientemente larga, use una manguera de desagi.ie nueva con

una Iongitud m6xima de 12 pies (3,7 m), que cumpla con todas las

pruebas de los est6ndares actuales de AHAM/IAPMO (por sus siglas

en ingles, los Fabricantes Estadounidenses de Electrodom_sticos para

Uso Dom_stico y la Asociaci6n Internacional de Funcionarios de

Fontanerfa y Mec6nica), que sea resistente al calory al detergente y

encaje en el conector de desagiJe de 1" (2,5 cm) de la lavavajillas.

• Conecte la manguera de desagi.ie al tubo de desperdicios en "T" o a

la entrada del recipiente de desechos que se encuentra arriba del

sif6n de desagi.ie en la tuberfa de la casa, y a un m_nimo de 20"

(50,8 cm) del piso. Se recomienda que la manguera de desagiJe se

enlace y quede asegurada firmemente a la parte inferior del

mostrador, o que se conecte a una purga de aire.

Purga de aire del desagOe

Use una purga de aire del desagiJe si la manguera de desagLie est6

conectada a la tuberfa de la casa a una altura menor alas 20"

(50,8 cm) sobre el contrapiso o el piso.

Use accesorios para la I[nea de desagiJe con un di6metro interior de

1/2" (1,3 cm) como minimo.

La page charge ...

Kenmore 66513349K606 Guide d'installation

Marque: Kenmore

Modèle: 66513349K606

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Kenmore 66513349K606 Installation guide
español: Kenmore 66513349K606 Guía de instalación

Kenmore 66513349K606 Guide d'installation

Ce manuel convient également à

Kenmore 66513349K606 Guide d'installation

dans d''autres langues

Autres documents