Chicago Pneumatic CP 4130 Mode d'emploi

CP 0016, 4130, 4131, 4132, 4134

EN Safety and operating instructions

Handheld pneumatic pick hammers

DA Sikkerhedsinstruktioner og

betjeningsvejledning

Håndholdte trykluftmejselhamre

EL Οδηγίες Ασφάλειας και Χειρισμού

Αερόσφυρες χειρός

TR Güvenlik ve kullanım talimatları

El tipi pnömatik martopikörler

PL Instrukcja Bezpieczeństwa i

Eksploatacji

Lekki młot pneumatyczny

RU инструкций по технике

безопасности и эксплуатации

Ручные пневматические отбойные молотки

NO Sikkerhetsinstrukser og

bruksanvisning

Håndholdte pneumatiske pakkhammere

FI Turvallisuusohjeet ja käyttöohje

Käsikäyttöiset paineilmapiikkausvasarat

NL Veiligheidsvoorschriften en

bedieningshandleiding

Handbediende pneumatische bikhamers

IT Istruzioni per la sicurezza e per l'uso

Martelli picconatori pneumatici manuali

PT Instruções de segurança e operação

Martelos picadores

www.cp.com

ES Instrucciones de seguridad y de

funcionamiento

Martillos picadores neumáticos manuales

FR Prescriptions de sécurité et

instructions pour l'opérateur

Marteaux-piqueurs pneumatiques portatifs

DE Sicherheits- und Betriebsanleitung

Hand-Druckluftaufbrechhämmer

SV Säkerhetsinstruktion och

bruksanvisning

Handhållna tryckluftsdrivna bilningshammare

www.cp.com

Contents

ENGLISH ........................................................................................ 5

DANSK ......................................................................................... 23

ελληνικά ........................................................................................ 41

TÜRKÇE ....................................................................................... 61

JĘZYK ........................................................................................... 79

РУССИЙ ....................................................................................... 99

NORSK ....................................................................................... 119

SUOMI ....................................................................................... 137

NEDERLANDS ............................................................................. 155

ITALIANO ................................................................................... 175

PORTUGUÊS ............................................................................... 195

ESPAÑOL .................................................................................... 215

FRANÇAIS .................................................................................. 235

DEUTSCH ................................................................................... 255

SVENSKA ................................................................................... 275

www.cp.com

ENGLISH

Contents

Introduction ...................................................................................................................................................... 7

About the Safety and operating instructions .................................................................................................... 7

Safety instructions ............................................................................................................................................ 7

Safety signal words ..................................................................................................................................... 7

Personal precautions and qualifications ..................................................................................................... 7

Personal protective equipment .............................................................................................................. 7

Drugs, alcohol or medication ................................................................................................................. 7

Installation, precautions .............................................................................................................................. 8

Operation, precautions ............................................................................................................................... 8

Maintenance, precautions ......................................................................................................................... 11

Storage, precautions ................................................................................................................................. 12

Overview ........................................................................................................................................................ 13

Design and function .................................................................................................................................. 13

Choosing the correct pneumatic hammer for a task ................................................................................. 13

Main parts ................................................................................................................................................. 13

Labels ....................................................................................................................................................... 14

Data plate ............................................................................................................................................ 14

Noise level label ................................................................................................................................... 15

Safety label .......................................................................................................................................... 15

Installation ...................................................................................................................................................... 15

Hoses and connections ............................................................................................................................ 15

Methods to prevent freezing ..................................................................................................................... 15

Connecting a water separator ................................................................................................................... 15

Lubrication ................................................................................................................................................ 15

Working tool .............................................................................................................................................. 16

Selecting the right working tool ............................................................................................................ 16

Narrow chisel ....................................................................................................................................... 16

Moil point ............................................................................................................................................. 16

Wide bladed chisel ............................................................................................................................... 16

Fitting and removing the working tool .................................................................................................. 16

Operation ....................................................................................................................................................... 17

Start and stop ........................................................................................................................................... 17

Operating .................................................................................................................................................. 18

Starting a cut ........................................................................................................................................ 18

Breaking ............................................................................................................................................... 18

When taking a break ................................................................................................................................. 18

Maintenance .................................................................................................................................................. 18

Every day .................................................................................................................................................. 18

Periodic maintenance ............................................................................................................................... 19

Tightening torques .................................................................................................................................... 19

Troubleshooting ............................................................................................................................................. 19

Storage .......................................................................................................................................................... 19

Disposal ......................................................................................................................................................... 19

Technical data ................................................................................................................................................ 20

CP 0016, 4130, 4131, 4132, 4134

Contents

9800 0616 71 | Original instructions

5

Machine data ............................................................................................................................................ 20

Noise and vibration declaration statement ................................................................................................ 20

Noise and vibration data ........................................................................................................................... 21

EC Declaration of Conformity ........................................................................................................................ 22

EC Declaration of Conformity (EC Directive 2006/42/EC) ........................................................................ 22

Contents

CP 0016, 4130, 4131, 4132, 4134

6

9800 0616 71 | Original instructions

Introduction

Thank you for choosing Chicago Pneumatic brand

products. For over a century, the Chicago

Pneumatic brand has represented performance

and innovation in the pneumatic tool industry.

Today the brand is found around the world on a

range of pneumatic and hydraulic tools that

includes breakers, rock drills, chipping hammers,

clay-diggers, picks and busters, scabblers, pumps

and a whole lot more.

The Chicago Pneumatic brand is associated with

powerful and reliable products that are easy to

maintain and that give good value for the money.

For more information please visit www.cp.com

Atlas Copco (India) Ltd

90, M.I.D.C Industrial area

Satpur, Nashik, Maharashtra

422 007 India

About the Safety and

operating instructions

The aim of the instructions is to provide you with

knowledge of how to use the pneumatic pick

hammer in an efficient, safe way. The instructions

also give you advice and tell you how to perform

regular maintenance on the pneumatic pick

hammer.

Before using the pneumatic pick hammer for the

first time you must read these instructions carefully

and understand all of them.

Safety instructions

To reduce the risk of serious injury or death to

yourself or others, read and understand the Safety

and operating instruction before installing,

operating, repairing, maintaining, or changing

accessories on the machine.

Post this Safety and operating instruction at work

locations, provide copies to employees, and make

sure that everyone reads the Safety and operating

instruction before operating or servicing the

machine. For professional use only.

In addition, the operator or the operator's employer

must assess the specific risks that may be present

as a result of each use of the machine.

Save all warnings and instructions for future

reference.

Safety signal words

The safety signal words Danger, Warning and

Caution have the following meanings:

DANGER Indicates a hazardous

situation which, if not avoided,

will result in death or serious

injury.

WARNING Indicates a hazardous

situation which, if not avoided,

could result in death or

serious injury.

CAUTION Indicates a hazardous

situation which, if not avoided,

could result in minor or

moderate injury.

Personal precautions and

qualifications

Only qualified and trained persons may operate or

maintain the machine. They must be physically

able to handle the bulk, weight, and power of the

tool. Always use your common sense and good

judgement.

Personal protective equipment

Always use approved protective equipment.

Operators and all other persons in the working

area must wear protective equipment, including at

a minimum:

•

Protective helmet

•

Hearing protection

•

Impact resistant eye protection with side

protection

•

Respiratory protection when appropriate

•

Protective gloves

•

Proper protective boots

•

Appropriate work overall or similar clothing (not

loose-fitting) that covers your arms and legs.

Drugs, alcohol or medication

WARNING Drugs, alcohol or medication

Drugs, alcohol or medication may impair your

judgment and powers of concentration. Poor

reactions and incorrect assessments can lead to

severe accidents or death.

►

Never use the machine when you are tired or

under the influence of drugs, alcohol or

medication.

CP 0016, 4130, 4131, 4132, 4134

Safety and operating instructions

9800 0616 71 | Original instructions

7

►

No person who is under the influence of drugs,

alcohol or medication may operate the

machine.

Installation, precautions

DANGER Whipping air hose

A compressed air hose that comes loose can lash

around and cause personal injury or death. To

reduce this risk:

►

Check that the compressed air hose and the

connections are not damaged, replace if

necessary.

►

Check that all compressed air connections are

properly attached.

►

Never carry a pneumatic machine by the air

hose.

►

Never attempt to disconnect a compressed air

hose that is pressurized. First switch off the

compressed air at the compressor and then

bleed the machine by activating the start and

stop device.

►

Do not use quick disconnect couplings at tool

inlet. Use hardened steel (or material with

comparable shock resistance) threaded hose

fittings.

►

Whenever universal twist couplings (claw

couplings) are used, we recommend that lock

pins are installed and whipcheck safety cables

are used to safeguard against possible hose to

tool and hose to hose connection failure.

►

Never point a compressed air hose at yourself

or anyone else. To avoid the risk of getting

injured, never use compressed air to blow for

example dust, dirt etc. from your clothes.

WARNING Ejected working tool

If the tool retainer on the machine is not in a locked

position, the inserted tool can be ejected with

force, which can cause personal injury.

►

Never start the machine while changing the

working tool.

►

Before changing the working tool or

accessories, stop the machine, switch off the

power supply and bleed the machine by

activating the start and stop device.

►

Never point the inserted tool at yourself or

anyone else.

►

Make sure that the working tool is fully inserted

and the tool retainer is in a locked position

before the machine is started.

►

Check the locking function by pulling the

inserted tool outwards forcefully.

WARNING Moving or slipping working tool

An incorrect dimension of the inserted tool’s shank

can result in that the inserted tool is lost or is

slipping out during operation. Risk of severe injury

or crushed hands and fingers.

►

Check that the working tool has the shank

length and dimensions that the machine is

intended for.

►

Never use an working tool without a collar.

Operation, precautions

DANGER Explosion hazard

If an working tool comes into contact with

explosives or explosive gases, an explosion could

occur. When working on certain materials and

when using certain materials in machine parts,

sparks and ignition can occur. Explosions will lead

to severe injuries or death.

►

Never operate the machine in any explosive

environment.

►

Never use the machine near flammable

materials, fumes or dust.

►

Make sure that there are no undetected

sources of gas or explosives.

WARNING Unexpected movements

The working tool is exposed to heavy strains when

the machine is used. The working tool may break

due to fatigue after a certain amount of use. If the

working tool breaks or gets stuck, there may be

sudden and unexpected movement that can cause

injuries. Furthermore, losing your balance or

slipping may cause injury.

►

Make sure that you always keep a stable

position with your feet as far apart as your

shoulder width, and keeping a balanced body

weight.

►

Always inspect the equipment prior to use.

Never use the equipment if you suspect that it

is damaged.

►

Make sure that the handles are clean and free

of grease and oil.

►

Keep your feet away from the working tool.

►

Stand firmly and always hold on to the machine

with both hands.

►

Never start the machine when it is lying on the

ground.

Safety and operating instructions

CP 0016, 4130, 4131, 4132, 4134

8

9800 0616 71 | Original instructions

►

Never ‘ride’ on the machine with one leg over

the handle.

►

Never strike or abuse the equipment.

►

Check regularly for wear on the working tool,

and check whether there are any signs of

damage or visible cracks.

►

Pay attention and look at what you are doing.

WARNING Dust and fume hazard

Dusts and/or fumes generated or dispersed when

using the machine may cause serious and

permanent respiratory disease, illness, or other

bodily injury (for example, silicosis or other

irreversible lung disease that can be fatal, cancer,

birth defects, and/or skin inflammation).

Some dusts and fumes created by drilling,

breaking, hammering, sawing, grinding and other

construction activities contain substances known to

the State of California and other authorities to

cause respiratory disease, cancer, birth defects, or

other reproductive harm. Some examples of such

substances are:

•

Crystalline silica, cement, and other masonry

products.

•

Arsenic and chromium from chemically-treated

rubber.

•

Lead from lead-based paints.

Dust and fumes in the air can be invisible to the

naked eye, so do not rely on eye sight to

determine if there is dust or fumes in the air.

To reduce the risk of exposure to dust and fumes,

do all of the following:

►

Perform site-specific risk assessment. The risk

assessment should include dust and fumes

created by the use of the machine and the

potential for disturbing existing dust.

►

Use proper engineering controls to minimize the

amount of dust and fumes in the air and to

minimize build-up on equipment, surfaces,

clothing, and body parts. Examples of controls

include: exhaust ventilation and dust collection

systems, water sprays, and wet drilling. Control

dusts and fumes at the source where possible.

Make sure that controls are properly installed,

maintained and correctly used.

►

Wear, maintain and correctly use respiratory

protection as instructed by your employer and

as required by occupational health and safety

regulations. The respiratory protection must be

effective for the type of substance at issue (and

if applicable, approved by relevant

governmental authority).

►

Work in a well ventilated area.

►

If the machine has an exhaust, direct the

exhaust so as to reduce disturbance of dust in a

dust filled environment.

►

Operate and maintain the machine as

recommended in the operating and safety

instructions

►

Select, maintain and replace consumables/

working tools/ other accessories as

recommended in the operating and safety

instructions. Incorrect selection or lack of

maintenance of consumables/ inserted tools/

other accessories may cause an unnecessary

increase in dust or fumes.

►

Wear washable or disposable protective clothes

at the worksite, and shower and change into

clean clothes before leaving the worksite to

reduce exposure of dust and fumes to yourself,

other persons, cars, homes, and other areas.

►

Avoid eating, drinking, and using tobacco

products in areas where there is dust or fumes.

►

Wash your hands and face thoroughly as soon

as possible upon leaving the exposure area,

and always before eating, drinking, using

tobacco products, or making contact with other

persons.

►

Comply with all applicable laws and regulations,

including occupational health and safety

regulations.

►

Participate in air monitoring, medical

examination programs, and health and safety

training programs provided by your employer or

trade organizations and in accordance with

occupational health and safety regulations and

recommendations. Consult with physicians

experienced with relevant occupational

medicine.

►

Work with your employer and trade organization

to reduce dust and fume exposure at the

worksite and to reduce the risks. Effective

health and safety programs, policies and

procedures for protecting workers and others

against harmful exposure to dust and fumes

should be established and implemented based

on advice from health and safety experts.

Consult with experts.

►

Residues of hazardous substances on the

machine can be a risk. Before undertaking any

maintenance on the machine, clean it

thoroughly.

CP 0016, 4130, 4131, 4132, 4134

Safety and operating instructions

9800 0616 71 | Original instructions

9

WARNING Projectiles

Failure of the work piece, of accessories, or even

of the machine itself may generate high velocity

projectiles. During operating, splinters or other

particles from the working material may become

projectiles and cause personal injury by striking the

operator or other persons. To reduce these risk:

►

Use approved personal protective equipment

and safety helmet, including impact resistant

eye protection with side protection.

►

Make sure that no unauthorised persons

trespass into the working zone.

►

Keep the workplace free from foreign objects.

►

Ensure that the work piece is securely fixed.

WARNING Splinters hazard

Using the working tool as a hand struck tool can

result in splinters hitting the operator and can

cause personal injury.

►

Never use a working tool as a hand struck tool.

They are specifically designed and heat-treated

to be used only in a machine.

WARNING Slipping, tripping and falling

hazards

There is a risk of slipping, tripping or falling, for

example tripping on hoses or on other objects.

Slipping, tripping or falling can cause injury. To

reduce this risk:

►

Always make sure that no hose or other object

is in your way or in any other person's way.

►

Always make sure you are in a stable position

with your feet as far apart as your shoulder

width and keeping a balanced body weight.

WARNING Motion hazards

When using the machine to perform work-related

activities, you may experience discomfort in the

hands, arms, shoulders, neck, or other parts of the

body.

►

Adopt a comfortable posture while maintaining

secure footing and avoiding awkward off-

balanced postures.

►

Changing posture during extended tasks may

help avoid discomfort and fatigue.

►

In case of persistent or recurring symptoms,

consult a qualified health professional.

WARNING Vibration hazards

Normal and proper use of the machine exposes

the operator to vibration. Regular and frequent

exposure to vibration may cause, contribute to, or

aggravate injury or disorders to the operator’s

fingers, hands, wrists, arms, shoulders and/or

nerves and blood supply or other body parts,

including debilitating and/or permanent injuries or

disorders that may develop gradually over periods

of weeks, months, or years. Such injuries or

disorders may include damage to the blood

circulatory system, damage to the nervous system,

damage to joints, and possibly damage to other

body structures.

If numbness, persistent recurring discomfort,

burning sensation, stiffness, throbbing, tingling,

pain, clumsiness, weakened grip, whitening of the

skin, or other symptoms occur at any time, when

operating the machine or when not operating the

machine, stop operating the machine, tell your

employer and seek medical attention. Continued

use of the machine after the occurrence of any

such symptom may increase the risk of symptoms

becoming more severe and/or permanent.

Operate and maintain the machine as

recommended in these instructions, to prevent an

unnecessary increase in vibration.

The following may help to reduce exposure to

vibration for the operator:

►

Let the machine do the job. Use a minimum

hand grip consistent with proper control and

safe operation. Use the correct feed force on

the machine. Avoid pressing too hard.

►

If the machine has vibration absorbing handles,

keep them in a central position, avoid pressing

the handles into the end stops.

►

When the percussion mechanism is activated,

the only body contact with the machine you

should have are your hands on the handle or

handles. Avoid any other contact, for example

supporting any part of the body against the

machine or leaning onto the machine trying to

increase the feed force. It is also important not

to keep the start and stop device engaged while

extracting the tool from the work surface.

►

Make sure that the inserted tool is well-

maintained (including sharpness, if a cutting

tool), not worn out, and of the proper size.

Working tools that are not well-maintained, or

that are worn out, or that are not of the proper

size result in longer time to complete a task

(and a longer period of exposure to vibration)

and may result in or contribute to higher levels

of vibration exposure.

Safety and operating instructions

CP 0016, 4130, 4131, 4132, 4134

10

9800 0616 71 | Original instructions

►

Immediately stop working if the machine

suddenly starts to vibrate strongly. Before

resuming the work, find and remove the cause

of the increased vibrations.

►

Never grab, hold or touch the inserted tool

when using the machine.

►

Participate in health surveillance or monitoring,

medical exams and training programs offered

by your employer and when required by law.

►

When working in cold conditions wear warm

clothing and keep hands warm and dry.

►

The exhaust air is strongly chilled and shall not

make contact with the operator. Always direct

the exhaust air away from hands and body.

See the ”Noise and vibration declaration

statement” for the machine, including the declared

vibration values. This information can be found at

the end of these Safety and operating instructions.

◆

Comply with the recommended air-pressure

when operating the machine. Either higher or

lower air-pressure has the potential of resulting

in higher levels of vibration.

DANGER Electrical hazard

The machine is not electrically insulated. If the

machine comes into contact with electricity, serious

injuries or death may result.

►

Never operate the machine near any electric

wire or other source of electricity.

►

Make sure that there are no concealed wires or

other sources of electricity in the working area.

WARNING Concealed object hazard

During operating, concealed wires and pipes

constitute a danger that can result in serious injury.

►

Check the composition of the material before

operating.

►

Watch out for concealed cables and pipes for

example electricity, telephone, water, gas and

sewage lines etc.

►

If the inserted tool seems to have hit a

concealed object, switch off the machine

immediately.

►

Make sure that there is no danger before

continuing.

WARNING Involuntary start

Involuntary start of the machine may cause injury.

►

Keep your hands away from the start and stop

device until you are ready to start the machine.

►

Learn how the machine is switched off in the

event of an emergency.

►

Release the start and stop device immediately

in all cases of power supply interruption.

►

Whenever fitting or removing the working tool,

switch off the air supply, bleed the machine by

pressing the start and stop device and

disconnect the machine from the power source.

WARNING Noise hazard

High noise levels can cause permanent and

disabling hearing loss and other problems such as

tinnitus (ringing, buzzing, whistling or humming in

the ears). To reduce risk and prevent an

unnecessary increase in noise levels:

►

Risk assessment of these hazards and

implementation of appropriate controls is

essential.

►

Operate and maintain the machine as

recommended in these instructions.

►

Select, maintain and replace the working tool as

recommended in these instructions.

►

If the machine has a muffler, check that it is in

place and in good working condition.

►

Always use hearing protection.

►

Use damping material to prevent work pieces

from "ringing".

Maintenance, precautions

WARNING Machine modification

Any machine modification may result in bodily

injuries to yourself or others.

►

Never modify the machine. Modified machines

are not covered by warranty or product liability.

►

Always use approved original parts, tools, and

accessories.

►

Change damaged parts immediately.

►

Replace worn components in good time.

CAUTION Hot working tool

The tip of the working tool can become hot and

sharp when used. Touching it can lead to burns

and cuts.

►

Never touch a hot or sharp working tool.

►

Wait until the working tool has cooled down

before carrying out maintenance work.

CP 0016, 4130, 4131, 4132, 4134

Safety and operating instructions

9800 0616 71 | Original instructions

11

WARNING Working tool hazards

Accidental engagement of the start and stop

device during maintenance or installation can

cause serious injuries, when the power source is

connected.

►

Never inspect, clean, install, or remove the

working tool while the power source is

connected.

Storage, precautions

◆

Keep the machine and tools in a safe place, out

of the reach of children and locked up.

Safety and operating instructions

CP 0016, 4130, 4131, 4132, 4134

12

9800 0616 71 | Original instructions

Overview

To reduce the risk of serious injury or death to

yourself or others, read the Safety instructions

section found on the previous pages of this manual

before operating the machine.

Design and function

These instructions apply to the CP 0016, CP 4130,

CP 4131, CP4132 and CP4134 models.

These machines are pneumatic tools designed for

medium duty to heavy duty chipping, cutting and

trimming as well as light concrete demolition and

soft tunnelling. Each machine model can be used

both horizontally and vertically. No other use is

permitted.

To choose the correct working tool, see the spare

parts list.

Choosing the correct

pneumatic hammer for a task

It is important to choose the correct size of

pneumatic hammer for the work to be performed.

A pneumatic hammer that is too small means that

the work will take longer.

A hammer that is too big means that there must be

frequent repositioning, which is unnecessarily tiring

for the operator.

A simple rule for choosing the correct size of

pneumatic hammer is that a normal sized piece of

broken material should be removed from the

workpiece within 5–10 seconds operation.

•

If it takes less than 5 seconds a smaller

pneumatic hammer should be selected.

•

If it takes more than 10 seconds a larger

pneumatic hammer should be selected.

Main parts

A

B

C

D

E

F

G

CP 0016

A

B

C

D

E

G

F

CP 4130

CP 0016, 4130, 4131, 4132, 4134

Safety and operating instructions

9800 0616 71 | Original instructions

13

A

B

C

D

E

G

F

CP 4131

A

B

D

E

F

G

CP 4132

A

B

D

E

F

G

CP 4134

A. Handle

B. Trigger

C. Lock off trigger

D. Tool retainer

E. Air inlet

F. Muffler

G. Cylinder

Labels

The machine is fitted with labels containing

important information about personal safety and

machine maintenance. The labels must be in such

condition that they are easy to read. New labels

can be ordered from the spare parts list.

Data plate

Construction Tools PC AB

A

B C

p max

D

Del. wt.

Production year

xxxx

E

Type

Made in

Ser. No.

A. Machine type

B. Maximum hydraulic pressure

C. Serial number

Safety and operating instructions

CP 0016, 4130, 4131, 4132, 4134

14

9800 0616 71 | Original instructions

D. The warning symbol together with the book

symbol means that the user must read the

safety and operating instructions before the

machine is used for the first time.

E. The CE symbol means that the machine is EC-

approved. See the EC Declaration of

Conformity which is delivered with the machine

for more information.

Noise level label

WA

xxx

dB

The label indicates the guaranteed noise level

corresponding to EC-directive 2000/14/EC. See

"Technical data" for accurate noise level.

Safety label

To avoid injury, before using or servicing tool, read

and understand separately provided safety

instructions.

Installation

Hoses and connections

SRNO

A

B

C

D

A. Compressed air source

B. Water separator (optional)

C. Oiler (optional)

D. Max. 10 feet (3 meter) compressed air hose

between the oiler and the machine.

◆

Check that you are using the correct

recommended operating pressure, 87 psig (6

bar (e)).

◆

The maximum permissible air pressure, 90 psig

(6.2 bar (e)), must not be exceeded.

◆

Blow any impurities out of the compressed air

hose before connecting it to the machine.

◆

Select the correct dimension and length for the

compressed air hose. For hose lengths up to

100 feet (30 meters), a hose with a minimum

internal diameter of

3

⁄4 in. (19 mm) should be

used. If the hose length is between 100 and

330 feet (30 and 100 meters), a hose with a

minimum internal diameter of 1 in. (25 mm)

should be used.

Methods to prevent freezing

Ice formation in the muffler can occur when the

ambient air temperature is 32-50°F (0-10°C) and

the relative humidity is high.

The machine is designed to avoid the formation of

ice in the muffler. Despite this, under extreme

conditions ice can form in the muffler.

The following actions can be taken to further

counteract the risk of ice formation:

◆

Use CP Airolene Plus Tool Oil as a lubricant.

CP Airolene Plus Tool Oil counteracts freezing.

◆

Use a water separator.

Connecting a water separator

The length of the air hose between the compressor

and the water separator must be such that the

water vapour is cooled and condenses in the hose

before reaching the water separator.

If the ambient temperature is below 32 °F (0 °C)

the hose must be short enough to prevent the

water from freezing before reaching the water

separator.

Lubrication

The lubricant is important for the machine’s

function and has a great impact on the service life.

In order to supply the correct volume of oil, an oiler

should be connected to the air hose. The use of a

Chicago Pneumatic air line oiler is recommended.

To guarantee good lubrication, the length of the air

hose between the oiler and the pneumatic tool

should not exceed 10 feet (3 m).

Too much lubrication can cause starting problems,

low power or uneven performance.

CP 0016, 4130, 4131, 4132, 4134

Safety and operating instructions

9800 0616 71 | Original instructions

15

Use a synthetic lubricant such as CP Airolene Plus

Tool Oil or mineral oil with the properties

recommended in the table below.

Lubricant Temperature

range °F (°C)

Viscosity

CP Airolene Plus

Tool Oil

-4 to +120

(-20 to +50)

-

Air tool oil -4 to +60

(-20 to +15)

100-150 SUS

(ISO VG 22-32)

Air tool oil +60 to +120

(+15 to +50)

225-350 SUS

(ISO VG 46-68)

It is recommended that the oil contains a rust-

inhibitor.

Working tool

CAUTION Hot working tool

The tip of the working tool can become hot and

sharp when used. Touching it can lead to burns

and cuts.

►

Never touch a hot or sharp working tool.

►

Wait until the working tool has cooled down

before carrying out maintenance work.

NOTICE

Never cool a hot working tool in water, it

can result in brittleness and early failure.

Selecting the right working tool

Selecting the right working tool is a precondition for

proper machine function. It is important to select

working tools of high quality to avoid unnecessary

machine damage.

The machine can be destroyed if you use an

incorrect working tool.

Recommended working tools are listed in the

machine's spare parts list.

Narrow chisel

The narrow chisel is used for

demolition and cutting work in

concrete and other types of

hard materials.

Moil point

The moil point is only used for

making holes in concrete and

other types of hard materials.

Wide bladed chisel

The wide bladed chisel is

used in soft materials, such as

asphalt and frozen ground.

WARNING Vibration hazard

Using inserted tools that do not fulfil the criteria

mentioned below, will result in a longer time to

complete a task, and may result in higher levels of

vibration exposure. A worn tool will also cause

increased working time.

►

Make sure that the inserted tool is well-

maintained, not worn out and of the proper size.

►

Always use a sharp tool in order to work

efficiently.

Fitting and removing the working tool

Whenever fitting or removing the working tool the

following instructions must be observed:

◆

To prevent an accidental start: switch off the

power supply and disconnect the machine from

the power source. Bleed the machine by

pressing the start and stop device.

◆

Before inserting a tool, lubricate the tool shank

with grease.

◆

Close the tool retainer and check the lock

function by tugging the inserted tool sharply

outwards.

A

CP 0016

1. Slide the retainer over the shank and collar

onto the chisel.

2. Open the buffer (A) and place it on the chisel

between the retainer and the collar.

Safety and operating instructions

CP 0016, 4130, 4131, 4132, 4134

16

9800 0616 71 | Original instructions

3. Insert the chisel shank into the cylinder, and

screw the retainer onto the cylinder with hand

force until it is tight.

A

CP 4130, CP 4132

1. Insert the chisel shank into the cylinder.

2. Slide the retainer over the chisel and on to the

cylinder.

3. Insert the lock coil (A).

CP 4131

1. Screw the retainer on the cylinder by hand until

it is tight.

2. Push the retainer sleeve upwards and insert

the chisel shank in the cylinder.

3. Release the retainer sleeve and make sure the

sleeve returns to its end position.

A

CP 4134

1. Slide the retainer over the chisel and onto the

cylinder.

2. Insert the lock coil (A).

3. Push the retainer sleeve upwards and insert

the chisel shank in the cylinder.

4. Release the retainer sleeve and make sure the

sleeve returns to its end position.

Operation

WARNING Involuntary start

Involuntary start of the machine may cause injury.

►

Keep your hands away from the start and stop

device until you are ready to start the machine.

►

Learn how the machine is switched off in the

event of an emergency.

►

Stop the machine immediately in all cases of

power supply interruption.

Start and stop

A

B

C

D

The CP0016, CP4130 and CP4131 models are

equipped with a throttle lever and a lock-off trigger.

The lock-off trigger is positioned inside the D-

handle. It locks the throttle lever (positioned on top

of the D-handle) and prevents the machine from

starting accidentally.

◆

Start the machine by pulling the lock-off trigger

to position (A) and squeezing the throttle lever

towards position (C).

◆

Stop the machine by releasing the throttle lever

and the lock-off trigger. The throttle lever will

automatically return to position (D) and the lock-

off trigger will return to position (B).

CP 0016, 4130, 4131, 4132, 4134

Safety and operating instructions

9800 0616 71 | Original instructions

17

The CP 4132 and CP 4134 are equipped to with

inside trigger.

◆

Start the machine by pulling inside trigger to

upward position

◆

Stop the machine by releasing the inside

trigger.

Operating

Starting a cut

◆

Stand in a stable position with your feet well

away from the inserted tool.

◆

Press the machine against the working surface

before you start.

◆

Start collaring at such a distance from the edge

that the machine is capable of breaking the

material without leverage.

◆

Never try to break off too large pieces. Adjust

the breaking distance (A) so that the inserted

tool does not get stuck.

A

Breaking

◆

Let the machine do the work; do not press too

hard.

◆

Avoid working in extremely hard materials for

example granite and reinforcing iron (re-bar)

which would cause substantial vibrations.

◆

Any form of idling, operating without working

tool or operating with an uplifted machine must

be avoided.

◆

When the machine is lifted, the start and stop

device must not be activated.

◆

Check regularly that the machine is well

lubricated.

When taking a break

◆

During all breaks you must place the machine

in such a way that there is no risk for it to be

unintentionally started. Make sure to place the

machine on the ground, so that it can not fall.

◆

In the event of a longer break or when leaving

the workplace: Switch off the power supply and

then bleed the machine by activating the start

and stop device.

Maintenance

Regular maintenance is a basic requirement for

the continued safe and efficient use of the

machine. Follow the maintenance instructions

carefully.

◆

Before starting maintenance on the machine,

clean it in order to avoid exposure to hazardous

substances. See “Dust and fume hazard”.

◆

Use only authorised parts. Any damage or

malfunction caused by the use of unauthorised

parts is not covered by warranty or product

liability.

◆

When cleaning mechanical parts with solvent,

comply with appropriate health and safety

regulations and ensure there is satisfactory

ventilation.

◆

For major service of the machine, contact the

nearest authorised workshop.

◆

After each service, check that the machine's

vibration level is normal. If not, contact the

nearest authorised workshop.

Every day

Before undertaking any maintenance or changing

the working tool on pneumatic machines, always

switch off the air supply and bleed the machine by

depressing the start and stop device then

disconnect the air hose from the machine.

◆

Clean and inspect the machine and its functions

each day before the work commences.

◆

Check the tool retainer for wear and function.

◆

Conduct a general inspection for leaks and

damage.

◆

Check that the air inlet nipple is tightened and

that the claw coupling is free from damage.

Safety and operating instructions

CP 0016, 4130, 4131, 4132, 4134

18

9800 0616 71 | Original instructions

◆

For the machine to maintain the specified

vibration values, always check the following:

Too large a clearance between the working

tool’s shank and the chisel bushing will

generate increased vibrations. To avoid getting

exposed to excessive vibrations, check the

chisel bushing for wear every day.

◆

If the machine has a vibration-absorbing

handle/handles, check that it moves freely (up

and down) and does not jam.

◆

Change damaged parts immediately.

◆

Replace worn components in good time.

◆

Make sure that all the attached and related

equipment, such as hoses, water separators

and oilers are properly maintained.

Periodic maintenance

After each operating period of approximately 150

impact hours or twice a year the machine must be

dismantled and all parts be cleaned and checked.

This work must be performed by authorised staff

who are trained for this task.

Tightening torques

A

B

C

A. Air inlet nipple: 65-75 lbf/ft (88-102 Nm), use

Loctite® 243™ (Loctite is a registered

trademark of Henkel Corporation. 243 is a

trademark of Henkel Corporation.)

B. Nut: First tighten the four nuts diagonally with a

torque of 15 lbf/ft (20 Nm). Then tighten the

nuts in sequence using the same torque. This is

to allow the nylon bumper to set properly.

C. Nylon bumper

Troubleshooting

If the pneumatic machine does not start, has low

power or uneven performance, check the following

points.

◆

Check that the working tool being used has the

correct shank dimension.

◆

Check that the pneumatic machine is getting

the correct amount of lubricant. Too much

lubrication can cause starting problems, low

power or uneven performance.

◆

Check that the compressed air system supplies

the machine with sufficient air pressure to give

full power.

◆

Check that the dimension and length of the air

hose are according to the recommendations.

See “Installation”.

◆

If there is a risk of freezing, check that the

machine's exhaust ports are not blocked.

◆

If the machine function is still not satisfactory

after this procedure, contact an authorised

service workshop.

Storage

•

Clean the machine properly before storage, in

order to avoid hazardous substances. See

“Dust and fume hazard”

•

Pour approximately

1

⁄2 oz (5 cl) of oil directly into

the air inlet nipple, connect the machine to the

compressed air supply and start it for a few

seconds.

•

Always store the machine in a dry place.

Disposal

A used machine must be treated and disposed of

in such a way that the greatest possible portion of

the material can be recycled and any negative

influence on the environment is kept as low as

possible, and in respect to local restrictions.

CP 0016, 4130, 4131, 4132, 4134

Safety and operating instructions

9800 0616 71 | Original instructions

19

Technical data

Machine data

Type Shank dimension

in.

(mm)

Weight

lb

(kg)

Length

in.

(mm)

Impact freq.

Hz

Air consumption

foot

3

/min

(l/s)

CP 0016 H19 H

3

⁄4 x 2

(H 19 x 50)

18 ¾

(8.5)

16

1

⁄2

(420)

32 26

(12)

CP 4130 3H H 0.580

(H 14.7)

18 ¾

(8.5)

16

1

⁄2

(420)

32 26

(12)

CP 4130 3R Rd. 0.680

(R 17.3)

18 ¾

(8.5)

16

1

⁄2

(420)

32 26

(12)

CP 4130 4H H 0.580

(H 14.7)

19 ¾

(9.0)

17

3

⁄4

(450)

25 27

(12.5)

CP 4130 4R Rd. 0.680

(R 17.3)

19 ¾

(9.0)

17

3

⁄4

(450)

25 27

(12.5)

CP 4131 3H H 0.580

(H 14.7)

18 ¾

(8.5)

16

1

⁄2

(420)

32 26

(12)

CP 4131 3R Rd. 0.680

(R 17.3)

18 ¾

(8.5)

16

1

⁄2

(420)

32 26

(12)

CP 4132 3H H 0.580

(H 14.7)

18 ¾

(8.5)

16

1

⁄2

(420)

32 26

(12)

CP 4132 3R Rd. 0.680

(R 17.3)

18 ¾

(8.5)

16

1

⁄2

(420)

32 26

(12)

CP 4132 4H H 0.580

(H 14.7)

19 ¾

(9.0)

18 ½

(470)

25 27

(12.5)

CP 4132 4R Rd. 0.680

(R 17.3)

19 ¾

(9.0)

18 ½

(470)

25 27

(12.5)

CP 4134 3H H 0.580

(H 14.7)

19 ¾

(9.0)

17

3

⁄4

(450)

32 26

(12)

CP 4134 3R Rd. 0.680

(R 17.3)

19 ¾

(9.0)

17

3

⁄4

(450)

32 26

(12)

CP 4134 4H H 0.580

(H 14.7)

22

(10.0)

19

3

⁄4

(500)

25 27

(12.5)

CP 4134 4R Rd. 0.680

(R 17.3)

22

(10.0)

19

3

⁄4

(500)

25 27

(12.5)

Noise and vibration declaration statement

Guaranteed sound power level Lw according to EN ISO 3744 in accordance with directive 2000/14/EC.

Sound pressure level Lp according to EN ISO 11203.

Vibration value A and uncertainty B determined according to EN ISO 28927-10. See table ”Noise and

vibration data” for the values of A, B, etc.

These declared values were obtained by laboratory type testing in accordance with the stated directive or

standards and are suitable for comparison with the declared values of other tools tested in accordance with

the same directive or standards. These declared values are not suitable for use in risk assessments and

values measured in individual work places may be higher. The actual exposure values and risk of harm

experienced by an individual user are unique and depend upon the way the user works, in what material the

machine is used, as well as upon the exposure time and the physical condition of the user, and the condition

of the machine.

Safety and operating instructions

CP 0016, 4130, 4131, 4132, 4134

20

9800 0616 71 | Original instructions

La page est en cours de chargement...

Chicago Pneumatic CP 4130 Mode d'emploi

Ce manuel convient également à

Chicago Pneumatic CP 4130 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents