Ryobi RY141600 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
Your pressure washer has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
ELECTRIC PRESSURE WASHER
LAVEUSE À PRESSION À ÉLECTRIQUE
LAVADORA DE PRESIÓN A ELÉCTRICA
RY141600
Ce nettoyeur haute pression a été conçu et fabriqué conformément
aux strictes normes de fiabilité, simplicité d’emploi et sécurité
d’utilisation. Correctement entretenu, il vous donnera des années
de fonctionnement robuste et sans problème.
AVERTISSEMENT : Pour réduire les risques de
blessures, l’utilisateur doit lire et veiller à bien comprendre le
manuel d’utilisation avant d’utiliser ce produit.
Merci de votre achat.
Su lavadora a presión ha sido diseñada y fabricada de conformidad
con las estrictas normas para brindar fiabilidad, facilidad de uso
y seguridad para el operador. Con el debido cuidado, le brindará
muchos años de sólido y eficiente funcionamiento.
ADVERTENCIA: Para reducir el riesgo de lesiones,
el usuario debe leer y comprender el manual del operador antes
de usar este producto.
Le agradecemos su compra.
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
SAVE THIS MANUAL FOR FUTURE REFERENCE
ii
See this fold-out section for all of the figures
referenced in the operator’s manual.
Consulter l’encart à volets afin d’examiner
toutes les figures mentionnées dans le manuel
d’utilisation.
Consulte esta sección desplegable para ver todas
las figuras a las que se hace referencia en el
manual del operador.
iii
Fig. 1
Fig. 2
A - Test button (bouton de test, botón de prueba)
B - Reset button (bouton de réinitialisation,
botón de reajuste)
A
B
Fig. 3
A - On/off switch (commutateur marche / arrêt, interruptor de encendido)
B - Nozzle storage (rangement de buses, almacenamiento para boquilla)
C - Spray wand (lance de pulvérisation, tubo rociado)
D - Soap tank cap (bouchon du réservoir de savon, tapa del tanque de jabón)
E - Trigger with lock-out (gâchette avec verouillage, gatillo con seguro)
F - Power cord storage (rangement pour cordon d’alimentation,
almacenamiento del cordón eléctrico)
G - Trigger handle (poignée de gâchete, mango del gatillo)
H - High pressure hose (tuyau haute pression, manguera de alta presión)
I - High pressure hose storage (rangement du tuyau flexible haute pression,
almacenamiento de la manguera de alta presión)
A - Pressure washer power cord (cordon d’alimentation de la laveuse à pression, cordón de corriente
de la lavadora de presión)
B - Drip loop (boucle d’égouttement, vuelta de goteo)
C - Extension cord (cordon prolongateurs, cordón de extensión)
A
B
C
A
B
E
C
I
H
F
D
G
iv
25
A - Threaded outlet (têton fileté, conexión
roscada)
B - Collar (collier, casquillo)
C - High pressure hose (flexible haute pression,
manguera de alta presión)
Fig. 4 Fig. 6
Fig. 7
Fig. 8
Fig. 11
A - Trigger handle (poignée à gâchette, mango
del gatillo)
B - Spray wand (poignée à gâchette, tubo
rociador)
A
A
B
C
B
Fig. 5
A - Collar (collier, casquillo)
B - Inlet coupler (raccord d’entrée, acoplador de
entrada)
C - High pressure hose (tuyau haute pression,
manguera de alta presión)
A - Water intake (rise d’eau, entrada de agua)
B - Garden hose (tuyau d’arrosage, manguera de
jardín)
C - Screen (tamis, cedazo)
A - On/off switch (commutateur marche / arrêt,
interruptor de encendido)
A - Trigger (gâchette, gatillo)
B - Lock-out (verrouillage, seguro)
A - Spray wand (lance de pulvérisation, tubo
rociador)
B - Nozzle (buse, boquilla)
C - Turbo nozzle (buse de turbo, boquilla de
turbo)
D - Pull back the quick-connect collar (tirer la
bague à connexion rapide, tire del collar de
conexión rápida)
E - Push the nozzle into place (insérer en place la
buse, introduzca la boquilla en su lugar)
F - Push the collar forward (poussez en avant la
bague, empuje del collar adelante)
A
B
C
Fig. 10
A
B
D
E
F
Fig. 9
A
A
A
C
B
B
A - Soap tank cap (bouchon du réservoir de
savon, tapa del tanque de jabón)
B - Detergent (détergente, detergente)
C
E
F
D
A
B
v
A - Threaded top (bouchon vissé, parte superior roscada)
B - Rubber seal (joint de caoutchouc, sello de goma)
C - Paper seal (sceaux de papier, sello de papel)
D - Water intake (rise d’eau, entrada de agua)
E - Pump outlet (sortie de la pompe, orificio de descarga de la bomba)
F - Pump protector (protecteur de pompe, protector de bomba)
Fig. 14
Fig. 15
A - Straightened paper clip (trombone droit, clip
para papel abierto)
B - Nozzle (embout, boquilla)
A
B
Fig. 12
Fig. 13
C
B
A
D
A
E
F
2
Introduction ......................................................................................................................................................................2
Introduction / Introducción
Important Safety Instructions ........................................................................................................................................... 3
Instructions importantes concernant la sécurité / Instrucciones de seguridad importantes
Specific Safety Rules .....................................................................................................................................................4-5
Règles de sécurité particulières / Reglas de seguridad específicas
Symbols ......................................................................................................................................................................... 6-7
Symboles / Símbolos
Electrical ........................................................................................................................................................................... 8
Caractéristiques électriques / Aspectos eléctricos
Features ............................................................................................................................................................................9
Caractéristiques / Características
Assembly .....................................................................................................................................................................9-10
Assemblage / Armado
Operation ................................................................................................................................................................... 11-14
Utilisation / Funcionamiento
Maintenance ..............................................................................................................................................................14-15
Entretien / Mantenimiento
Troubleshooting .............................................................................................................................................................. 16
Dépannage / Solución de problemas
Warranty ......................................................................................................................................................................... 17
Garantie / Garantía
Parts Ordering and Service ...............................................................................................................................Back Page
Commande de pièces et réparation / Pedidos de piezas y servicio ..................................... Page arrière / Pág. posterior
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
* * *
Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la
conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à
utiliser et à entretenir.
* * *
Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto
se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.
TABLE OF CONTENTS
TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO
INTRODUCTION
INTRODUCTION / INTRODUCCIÓN
3 — English
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock,
fire, and/or serious personal injury.
WARNING:
When using this product basic precautions should always
be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
THIS PRODUCT
To reduce the risk of injury, close supervision is
necessary when a product is used near children.
Be thoroughly familiar with controls. Know how to stop
the product and release pressure quickly.
Stay alert and exercise control. Watch what you are
doing and use common sense. Do not operate product
when you are tired. Do not rush.
Do not operate the product while under the influence
of drugs, alcohol, or any medication.
Keep the area of operation clear of all persons,
particularly small children, and pets.
Don’t overreach or stand on a ladder, rooftop, or other
unstable support. Keep proper footing and balance at
all times.
Follow the maintenance instructions specified in this
manual.
This product is provided with a ground fault
circuit interrupter built into the power cord plug. If
replacement of the plug or cord is needed, use only
identical replacement parts.
WARNING: Risk of injection or injury – Do not direct
discharge stream at persons.
SAVE THESE INSTRUCTIONS
GROUND FAULT CIRCUIT INTERRUPTER
PROTECTION
This pressure washer is provided with a ground fault circuit
interrupter (GFCI) built into the plug of the power supply
cord. This device provides additional protection from the risk
of electric shock. Should replacement of the plug or cord
become necessary, use only identical replacement parts that
include GFCI protection.
EXTENSION CORDS
See Figure 1.
Use only extension cords that are intended for outdoor use.
These extension cords are identified by a marking “Acceptable
for use with outdoor appliances; store indoors while not in
use.” Use only extension cords having an electrical rating
not less than the rating of the product. Do not use damaged
extension cords. Examine extension cord before using and
replace if damaged. Do not abuse extension cord and do
not yank on any cord to disconnect. Keep cord away from
heat and sharp edges. Always disconnect the extension cord
from the receptacle before disconnecting the product from
the extension cord. Always plug the extension cord into a
GFCI protected outlet.
To avoid the possibility of the tool plug getting wet when
using an extension cord, arrange a “drip loop” in the cord
connecting the pressure washer to the extension cord. The
“drip loop” is that part of the cord below the level of the
connector which prevents water travelling along the cord
and coming in contact with the connection. If the plug does
get wet, DO NOT unplug the cord. Disconnect the fuse or
circuit breaker that supplies power to the tool, then unplug
and examine for presence of water in the connection.
WARNING: To reduce the risk of electrocution, keep all
connections dry and off the ground. Do not touch plug with
wet hands.
SERVICING OF A DOUBLE-INSULATED
APPLIANCE
In a double-insulated product, two systems of insulation
are provided instead of grounding. No grounding means is
provided on a double-insulated product, nor should a means
for grounding be added to the product. Servicing a double-
insulated product requires extreme care and knowledge of
the system, and should be done only by qualified service
personnel. Replacement parts for a double insulated product
must be identical to the parts they replace. A double-insulated
product is marked with the words “DOUBLE INSULATION”
or “DOUBLE INSULATED.” The symbol may also be
marked on the product.
IMPORTANT SAFETY INSTRUCTIONS
4 — English
Use caution when positioning the pressure washer
for use. Warm air from the motor could cause discolored
spots on grass.
Know your product. Read the operator’s manual care-
fully. Learn the machine’s applications and limitations
as well as the specific potential hazards related to this
product.
To reduce the risk of injury, keep children and visitors
away. All visitors should wear safety glasses and be kept
a safe distance from work area.
Use right product. Don’t force product or attachment to
do a job it was not designed for. Don’t use it for a purpose
not intended.
Dress properly. Wear long pants and long sleeves. Do
not wear loose clothing, gloves, neckties, or jewelry. They
can get caught and draw you into moving parts. Rubber
gloves and nonskid footwear are recommended when
working outdoors. Also wear protective hair covering to
contain long hair.
Do not operate the equipment while barefoot or when
wearing sandals or similar lightweight footwear. Wear
protective footwear that will protect your feet and improve
your footing on slippery surfaces.
Exercise caution to avoid slipping or falling.
Alwaysweareyeprotectionwithsideshieldsmarked
to comply with ANSI Z87.1. Following this rule will
reduce the risk of serious personal injury.
Use only recommended accessories. The use of
improper accessories may cause risk of injury.
Check damaged parts. Before further use of the product,
a guard or other part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that may affect its
operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
Never leave product running unattended. Turn power
off. Don’t leave product until it comes to a complete stop.
Keep the motor free of grass, leaves, or grease to
reduce the chance of a fire hazard.
Follow manufacturer’s recommendations for safe
loading, unloading, transport, and storage of machine.
Keep product dry, clean, and free from oil and grease.
Always use a clean cloth when cleaning. Never use
brake fluids, gasoline, petroleum-based products, or any
solvents to clean product.
Check the work area before each use. Remove all
objects such as rocks, broken glass, nails, wire, or string
which can be thrown or become entangled in the
machine.
Do not use product if switch does not turn it off. Have
defective switches replaced by an authorized service
center.
Avoid dangerous environment. Don’t expose to rain.
Keep work area well lit.
Do not abuse the cord. Never use the cord to carry the
product or to disconnect the plug from an outlet. Keep
cord away from heat, oil, sharp edges, or moving parts.
Replace damaged cords immediately. Damaged cords
increase the risk of electric shock.
Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet(s) to be
used for the product. Receptacles are available having
built-in GFCI protection and may be used for this measure
of safety.
To reduce the risk of electric shock, this product has a
polarized plug (one blade is wider than the other) and
will require the use of a polarized extension cord. The
plug will fit into a polarized extension cord only one way. If
the plug does not fit fully into the extension cord, reverse
the plug. If the plug still does not fit, obtain a correct
polarized extension cord. A polarized extension cord will
require the use of a polarized wall outlet. This plug will
fit into the polarized wall outlet only one way. If the plug
does not fit fully into the wall outlet, reverse the plug. If
the plug still does not fit, contact a qualified electrician to
install the proper wall outlet. Do not change the equipment
plug, extension cord receptacle, or extension cord plug
in any way.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. A wire
gauge size (A.W.G.) of at least 14 is recommended for an
extension cord 25 feet or less in length. If in doubt, use
the next heavier gauge. The smaller the gauge number,
the heavier the cord. An undersized cord will cause a drop
in line voltage resulting in loss of power and overheating.
WARNING: Use outdoor extension cords marked SW-A,
SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOWA.
These cords are rated for outdoor use and reduce the risk
of electric shock.
Inspect extension cords periodically and replace if
damaged. Keep handles dry, clean, and free from oil or
grease.
Never direct a water stream toward people or pets,
or any electrical device.
Before starting any cleaning operation, close doors
and windows. Clear the area to be cleaned of debris,
toys, outdoor furniture, or other objects that could create
a hazard.
SPECIFIC SAFETY RULES
5 — English
Never spray close to the surface to be cleaned, as you
can damage the surface.
After stopping the motor, always pull the trigger on the
trigger handle to relieve stored pressure in the high
pressure hose. Failure to do so could result in serious
personal injury.
Ensure the high pressure hose is properly connected
before using the product.
Connect pressure washer only to an individual branch
circuit.
Hold the trigger handle securely with both hands.
Expect the trigger handle to move when the trigger is
pulled due to reaction forces. Failure to do so could cause
loss of control and injury to yourself and others.
For outdoor use only.
Save these instructions. Refer to them frequently and
use them to instruct other users. If you loan someone this
product, loan them these instructions also.
Do not use acids, alkalines, solvents, flammable
material, bleaches, or industrial grade solutions in this
product. These products can cause physical injuries to
the operator and irreversible damage to the machine.
WARNING: High pressure jets can be dangerous
if subject to misuse. The jet must not be directed at
persons, animals, electrical devices, or the machine itself.
Keep the motor away from flammables and other
hazardous materials.
Check bolts and nuts for looseness before each use. A
loose bolt or nut may cause serious motor problems.
Before storing, allow the motor to cool.
When servicing use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
ONLY use cold water.
Make sure minimum clearance of 3 feet is maintained
from combustible materials.
SPECIFIC SAFETY RULES
6 — English
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s Manual
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection
Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
Wet Conditions Alert Do not expose to rain or use in damp locations.
Risk of Injection
To reduce the risk of injection or injury, never direct a water stream
towards people or pets or place any body part in the stream. Leak-
ing hoses and fittings are also capable of causing injection injury.
Do not hold hoses or fittings.
Risk of Explosion
Do not spray flammable liquids. Flammable liquids and their vapors
are explosive and can cause severe burns or death.
Kickback
To reduce the risk of injury from kickback, hold the spray wand
securely with both hands when the machine is on.
Electric Shock
Failure to use in dry conditions and to observe safe practices can
result in electric shock.
Chemical Burns
To reduce the risk of injury or damage, DO NOT USE ACIDS,
ALKALINES, BLEACHES, SOLVENTS, FLAMMABLE MATERIAL,
OR INDUSTRIAL GRADE SOLUTIONS in this product.
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
NOTICE:
(Without Safety Alert Symbol) Indicates important information not related to an
injury hazard, such as a situation that may result in property damage.
7 — English
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
Alternating Current Type of current
n
o
No Load Speed Rotational speed, at no load
Class II Construction Double-insulated construction
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
8 — English
USE ONLY THIS SIZE EXTENSION CORD WHEN USING
THIS PRODUCT:
Cord Length Wire Size (A.W.G.)
25 ft. 14
50 ft. 12
100 ft. Not Allowed
NOTE: A.W.G. = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on lumber,
tools, or other obstructions while you are working with a
power tool. Failure to do so can result in serious personal
injury.
WARNING:
Check extension cords before each use. If damaged
replace immediately. Never use the product with a
damaged cord since touching the damaged area could
cause electrical shock resulting in serious injury.
GROUND FAULT CIRCUIT INTERRUPTER
See Figure 2.
This unit is equipped with a Ground Fault Circuit Interrupter
(GFCI), which guards against the hazards of ground fault
currents. An example of ground fault current is the current
that would flow through a person who is using an appliance
with faulty insulation and, at the same time, is in contact
with an electrical ground such as a plumbing fixture, wet
floor, or earth.
GFCI plugs do not protect against short circuits, overloads,
or shocks.
NOTE: To ensure readiness for use, press the reset button
each time you connect the pressure washer to the power
supply.
The GFCI plug can be tested with the TEST and RESET
buttons.
To test:
Press the TEST button. You will hear a “click” sound and
the red LED light will go out.
To restore power, press the RESET button. The LED light
will illuminate to indicate power has been restored.
Perform this test monthly to ensure proper operation of the
GFCI.
To reduce the risk of electric shock the supervisory
circuit must be operated before an appliance is
plugged into any receptacle on the device.
DOUBLE INSULATION
Double insulation is a concept in safety in electric power tools,
which eliminates the need for the usual three-wire grounded
power cord. All exposed metal parts are isolated from the
internal metal motor components with protecting insulation.
Double insulated products do not need to be grounded.
WARNING:
The double insulated system is intended to protect the
user from shock resulting from a break in the product’s
internal insulation. Observe all normal safety precautions
to avoid electrical shock.
NOTE: Servicing of a product with double insulation requires
extreme care and knowledge of the system and should
be performed only by a qualified service technician. For
service, we suggest you return the product to your nearest
authorized service center for repair. Always use original
factory replacement parts when servicing.
ELECTRICAL CONNECTION
This product has a precision-built electric motor. It should
be connected to a power supply that is 120 volts, AC only
(normal household current), 60 Hz. Do not operate this
product on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
the product does not operate when plugged into an outlet,
double-check the power supply.
EXTENSION CORDS
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw. An
undersized cord will cause a drop in line voltage, possibly
resulting in overheating, loss of power, and/or circuit
breaker or GFCI tripping. Use the chart to determine the
minimum wire size required in an extension cord. Only round
jacketed cords listed by Underwriter’s Laboratories (UL)
should be used.
When working outdoors with a product, use an extension
cord that is designed for outside use. This type of cord is
designated with “WA” or “W” on the cord’s jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
It is possible to tie the extension cord and power cord in a
knot to prevent them from becoming disconnected during
use. Make a knot, then connect the plug end of the power
cord into the receptacle end of the extension cord. This
method can also be used to tie two extension cords together.
ELECTRICAL
9 — English
PRODUCT SPECIFICATIONS
Maximum Pounds Per Square Inch* ........................................................................................................................1,600 psi
Maximum Gallons Per Minute ...................................................................................................................................1.2 GPM
Input .....................................................................................................................................120 V, 60 Hz, AC only, 13 Amps
*Max. rating determined by PWMA Standard 101
KNOW YOUR PRESSURE WASHER
See Figure 3.
The safe use of this product requires an understanding of the
information on the product and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
AUTOMATIC DETERGENT INJECTION
SYSTEM
Pour detergent into the soap tank to apply detergent quickly
and easily to your cleaning project. Use of the soap nozzle
will activate the detergent injector at a 20:1 dilution ratio.
CARRYING HANDLE
The pressure washer has a carrying handle for easy transport.
SOAP TANK
Remove the cap from the soap tank to add detergent to the
pressure washer.
GFCI PLUG
The pressure washer is equipped with a GFCI plug to guard
against the hazards of ground fault currents. This plug does
not protect against short circuits, overloads, or shocks.
HOSE STORAGE
Once the high pressure hose is rolled, hang it on the left side
of the machine using the hook-and-loop strap to secure in
place.
ON/OFF SWITCH
This switch turns the pressure washer on and off.
POWER CORD STORAGE
Once the power cord is rolled, hang it on the right side of the
machine using the hook-and-loop strap to secure in place.
TRIGGER HANDLE
The trigger handle has a gripping surface that provides
added control of the spray wand and helps reduce fatigue.
TRIGGER WITH LOCK-OUT
Pulling the trigger releases a stream of water for high
pressure cleaning. The lock-out provides protection against
unauthorized use.
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
WARNING:
Do not use this product if any parts on the Packing List
are already assembled to your product when you unpack
it. Parts on this list are not assembled to the product by
the manufacturer and require customer installation. Use
of a product that may have been improperly assembled
could result in serious personal injury.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product.
If any parts are damaged or missing, please call
1-800-860-4050 for assistance.
PACKING LIST
Electric Pressure Washer
20 ft. High Pressure Hose
Trigger Handle
Spray Wand
Nozzles (15º, Turbo, Soap)
Operator’s Manual
FEATURES
ASSEMBLY
10 — English
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this product.
Any such alteration or modification is misuse and could
result in a hazardous condition leading to possible serious
personal injury.
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
CONNECTING THE SPRAY WAND TO THE
TRIGGER HANDLE
See Figure 4.
Push the end of the spray wand into the trigger handle
and rotate clockwise to secure.
Pull on the spray wand to be certain it is properly secured.
CONNECTING HIGH PRESSURE HOSE TO
TRIGGER HANDLE
See Figure 5.
Screw the collar on the high pressure hose into the trigger
handle inlet coupler by turning the hose collar clockwise.
Tighten securely.
NOTE: Be careful to avoid cross-threading, which can
cause the trigger handle to leak during use.
Pull on the hose to be certain it is properly secured.
CONNECTING THE HIGH PRESSURE HOSE TO
THE PUMP
See Figure 6.
Completely uncoil and straighten the high pressure hose
to prevent kinks.
NOTE: See Using the High Pressure Hose in Operation
for more information about using the high pressure hose.
Align the collar on the threaded outlet on the pump.
Attach the high pressure hose collar onto the threaded
outlet.
Turn the collar clockwise to tighten the hose securely to
the pump.
NOTE: Be careful to avoid cross-threading, which can
cause the hose to leak during use.
Pull on the hose to be certain it is properly secured.
CONNECTING THE GARDEN HOSE TO THE
PRESSURE WASHER
See Figure 7.
NOTICE:
Always observe all local regulations when connecting
hoses to the water main. Some areas have restrictions
against connecting directly to public drinking water
supply to prevent the feedback of chemicals into the
drinking water supply. Direct connection through a
receiver tank or backflow preventer is usually permitted.
The water supply must come from a water main. NEVER use
hot water or water from pools, lakes, etc. Before connecting
the garden hose to the pressure washer:
Run water through the hose for 30 seconds to clean any
debris from the hose.
Inspect the screen in the water intake.
If the screen is damaged, do not use the machine until
the screen has been replaced.
If the screen is dirty, clean it before connecting the garden
hose to the machine.
To connect the garden hose to the machine:
Completely uncoil the garden hose or remove completely
from reel to prevent kinks.
NOTE: There must be a minimum of 10 feet of unrestricted
hose between the pressure washer intake and the hose
faucet or shut off valve (such as a “Y” shut off connector).
With the hose faucet turned completely off, attach the
end of the garden hose to the water intake. Tighten by
hand.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
ASSEMBLY
11 — English
WARNING:
Do not allow familiarity with the product to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended
can result in serious personal injury.
WARNING:
Never direct a water stream toward people or pets,
or any electrical device. Failure to follow these
instructions could result in serious injury, electric
shock, or death.
NOTICE:
Before each use, inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please call customer service or contact an
authorized service center for assistance.
APPLICATIONS
You may use this tool around the house for cleaning most
small to large horizontal or vertical exterior surfaces, smaller
exterior objects and structures, and outdoor equipment and
tools.* You can:
Clean or remove mold and mildew from weathered decks,
driveways, patios, walkways, sidewalks, etc.
Remove dirt from various exterior vertical surfaces such
as house exteriors, siding, fences, brick, concrete or stone
walls, etc.
Wash boats, outdoor furniture, powered or non-powered
garden equipment, gutters, window screens, grills,
playground equipment, etc.
*Always test in an inconspicuous area first.
PUMP LUBRICANT
The pressure washer pump has been filled with sufficient
lubricant at the factory and is maintenance free. You do not
need to check or add lubricant to the pump before initial use.
STARTING AND STOPPING THE PRESSURE
WASHER
See Figure 8.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
Before starting the motor:
Connect the garden hose.
NOTE: Make sure the pressure washer’s water intake
screen is in place and unclogged before connecting
garden hose.
Turn on the garden hose then pull the trigger to relieve air
pressure; hold the trigger until a steady stream of water
appears.
NOTE: Make sure the faucet is turned on fully and that
there are no kinks or leaks in the hose.
To start the motor:
With the on/off switch in the OFF position (O), connect
the pressure washer to the power supply.
NOTE: If using an extension cord, make sure to arrange
a drip loop as described on page 3.
WARNING:
To reduce the risk of electrocution, keep all connections
dry and off the ground. Do not touch plug with wet hands.
Press the reset button on the pressure washer’s plug to
make sure the unit is ready for operation.
Put the on/off switch in the ON position (I) to start the
motor.
OPERATION
12 — English
To stop the motor:
Put the on/off switch in the OFF position (O).
Pull trigger to release water pressure.
NOTE: The pressure washer may be on and the system
may have pressure even when the pump and/or motor
cannot be heard running. Always use caution around the
pressure washer.
USING THE TRIGGER AND LOCK-OUT
See Figure 9.
WARNING:
Hold the trigger handle securely with both hands. Expect
the trigger handle to move when the trigger is pulled due
to reaction forces. Failure to do so could cause loss of
control and injury to yourself and others.
Pull back and hold the trigger to operate the pressure
washer.
Release the trigger to stop the flow of water through the
nozzle.
To engage the lock out:
Push up on the lock out until it clicks into the slot.
To disengage the lock out:
Push the lock out down and into its original position.
Start with the nozzle 1–2 ft. away from the cleaning surface,
and carefully approach the surface just until the desired
level of cleaning is achieved. If the spray is too close it can
damage the cleaning surface.
SELECTING THE RIGHT NOZZLE FOR THE JOB
See Figure 10.
Each of the nozzles has a different spray pattern. Before
starting any cleaning job, determine the best nozzle for the
job. Refer to the Nozzle Selection Guide for more information
about which nozzle to choose.
WARNING:
NEVER remove nozzles without first turning off the motor,
disconnecting the power supply, relieving the water
pressure in the trigger handle, and locking the lock out
on the trigger handle. Never point the nozzle at your face
or at others. The quick-connect feature contains small
springs that could eject the nozzle with some force.
Failure to follow these instructions could result in an eye
injury or other serious personal injury.
OPERATION
NOZZLE SELECTION GUIDE
HIGH PRESSURE
(NO SOAP WHEN USING THESE NOZZLES)
LOW PRESSURE
(FOR SOAP OR
GENTLE RINSE)
Turbo Nozzle
15º
Blue or Black
Soap Nozzle
Concrete, Brick, Masonry
Siding, Gutters, House
Fencing, Deck, Patio
Lawn Equipment, Boat, RV
Recommended Nozzle Use With Caution for Certain Applications
13 — English
To connect a nozzle to the spray wand:
Turn off the pressure washer, disconnect the power
supply, and shut off the water supply. Pull trigger to
release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Pull back the quick-connect collar.
Push the nozzle into place in the spray wand.
Push the collar forward so that the nozzle is secured
properly. Check to see that the nozzle is secure.
To disconnect a nozzle from the spray wand once the
cleaning job is complete:
Turn off the pressure washer, disconnect the power
supply, and shut off the water supply. Pull trigger to
release water pressure.
Engage the lock-out on the trigger handle by pushing up
on the lock-out until it clicks into the slot.
Pull back and hold the quick-connect collar.
Remove the nozzle by pulling it from the quick-connect
collar. Place nozzle in the nozzle storage area on the top
of the machine.
USING THE HIGH PRESSURE HOSE
WARNING:
Injection hazard. Fully unwrap and straighten high
pressure hose prior to and during each use and do
not allow it to become kinked. The high pressure hose
features an outer covering that provides strength to the
hose. If the outer covering becomes damaged, stop using
the hose and replace it immediately. A kinked or damaged
hose can develop a high pressure leak and result in a
possible injection or other serious personal injury.
To prevent damage to the outer covering:
Inspect the hose before every use.
Fully unwrap and straighten hose before use.
Do not allow the high pressure hose to be kinked.
Keep hose away from hot surfaces and sharp edges.
Do not pull unit by high pressure hose.
Do not allow hose to be crushed or wrapped around
objects.
WASHING WITH DETERGENT
See Figures 11 - 12.
As sold, this unit is designed for use with “downstream”
pressure washer detergents. To convert for use with
“upstream” detergents, contact customer service or an
authorized customer service center for more information.
NOTICE:
USE ONLY DETERGENTS DESIGNED FOR PRESSURE
WASHERS. Do not use household detergents, acids,
alkalines, bleaches, solvents, flammable material, or
industrial grade solutions, which can damage the pump
or cause property damage. Many detergents may
require mixing prior to use. Prepare cleaning solution
as instructed on the solution bottle. Always test in an
inconspicuous area before beginning.
Disconnect pressure washer from power supply.
Pour detergent in the soap tank. Use a funnel, if needed,
to prevent accidental spilling of the detergent outside
the tank. If any detergent is spilled during the filling
process, make sure the unit is cleaned and dried before
proceeding.
NOTE: The machine setting of this unit is 20:1, which
usually allows the use of 1 gallon pressure washer
detergent without further dilution. Check your detergent
instructions to be sure additional dilution is not necessary.
Install the blue or black soap nozzle on the spray wand.
Connect unit to power supply and turn the pressure
washer on.
Squeeze the trigger and wait approximately 5 seconds
for the detergent to appear.
Spray the detergent on a dry surface using long, even,
overlapping strokes. To prevent streaking, do not allow
detergent to dry on the surface.
Before shutting off the motor:
Fill the soap tank with clean water.
Spray the clear water through the spray wand until the
tank is empty.
If any soap remains in the spray, repeat with a second
tank of clean water.
Shut off the motor.
NOTE: Shutting OFF ( O ) the motor will not relieve pressure
in the system. Pull trigger to release water pressure.
RINSING WITH THE PRESSURE WASHER
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Engage the lock out on the trigger handle by pushing up
on the lock out until it clicks into the slot.
Remove the soap nozzle by placing hand over nozzle then
pulling back the quick-connect collar. Place soap nozzle
in the nozzle storage area on the machine.
Select the right nozzle for the job. See the chart on the
previous page for selecting the appropriate nozzle.
Start at the top of the area to be rinsed and work down,
overlapping the strokes.
OPERATION
14 — English
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts could create a hazard or cause
product damage.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.
WARNING:
Before inspecting, cleaning, or servicing the machine,
shut off motor, wait for all moving parts to stop,
disconnect unit from power supply, and pull trigger to
release water pressure. Failure to follow these instructions
can result in serious personal injury or property damage.
NOTICE:
Periodically inspect the entire product for damaged,
missing, or loose parts such as screws, nuts, bolts, caps,
etc. Tighten securely all fasteners and caps and do not
operate this product until all missing or damaged parts
are replaced. Please call customer service or contact an
authorized service center for assistance.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken, or
destroy plastic which could result in serious personal
injury.
PUMP LUBRICATION
The pump on this unit is lubricated with a sufficient amount
of high grade lubricant for the life of the unit under normal
operating conditions. Therefore, no further lubrication is
required.
POWER SUPPLY CORD REPLACEMENT
If replacement of the power supply cord is necessary, this
must be done by an authorized service center in order to
avoid a safety hazard.
NOZZLE MAINTENANCE
See Figure 14.
Excessive pump pressure (a pulsing sensation felt while
squeezing the trigger) may be the result of a clogged or
dirty nozzle.
MAINTENANCE
OPERATION
USING PUMP PROTECTOR
See Figure 13.
Regular use of a commercially available pump protector
prolongs the life of the pressure washer by removing hard
water mineral deposits, lubricating pump seals and pistons,
and preventing freeze damage. Pump protector should
be added to the unit after every use and before storage.
Pump protector can be purchased at the retailer where you
purchased your pressure washer, or by calling customer
service.
The instructions that follow are typical for adding pump
protector but you should always verify the specific
instructions provided by the manufacturer of the pump
protector used.
Turn off the pressure washer motor, disconnect the power
supply, and shut off the water supply. Pull trigger to
release water pressure.
Disconnect garden hose and high pressure hose.
Unscrew threaded top from pump protector bottle and
remove paper seal from bottle. Reinstall top on bottle and
tighten securely.
NOTE: The rubber seal should remain inside the threaded
top. If it comes out, be sure to replace before reinstalling
the top.
Remove bottle cap and attach threaded end of bottle
securely to pressure washer pump water intake.
Squeeze bottle to inject contents into pump.
Pump is protected when the protector fluid exits the pump
outlet.
MOVING THE PRESSURE WASHER
Turn the pressure washer off. Point nozzle in a safe
direction and pull trigger to release water pressure.
Disconnect pressure washer from power supply.
Using the carrying handle, get a firm grasp of the unit.
Lift the unit into a safe and comfortable carrying position.
Move machine to the desired location.
15 — English
MAINTENANCE
Turn off the pressure washer and shut off the water
supply. Pull trigger to release water pressure.
Unplug the pressure washer.
Remove the nozzle from the spray wand.
WARNING:
NEVER remove nozzles without first turning off the motor,
relieving the water pressure in the trigger handle, and
locking the lock out on the trigger handle. NEVER point
the nozzle at your face or at others. The quick-connect
feature contains small springs that could eject the nozzle
with some force. Failure to follow these instructions could
result in an eye injury or other serious personal injury.
To free any foreign materials clogging or restricting the
nozzle, blow out or remove debris with a straightened
paper clip or fine needle.
Using a garden hose, flush debris out of nozzle by back
flushing (running the water through the nozzle backwards
or from the outside to the inside).
Reconnect the nozzle to the spray wand.
Reinstall the garden hose and connect the unit to the
power supply.
STORING THE PRESSURE WASHER
See Figure 15.
NOTE: Regular use of pump protector will give you
better performance of the unit and increase the life of
the pump. See the Replacement Parts List for available
sizes and part numbers of these items and call customer
service to order.
Store in a dry, covered area where the weather can’t damage it.
It is important to store this product in a frost-free area. Always
empty water from all hoses, the pump, and the detergent
bucket before storing.
Make sure the on/off switch is in the OFF position.
Unplug the pressure washer and store the power cord
using the hook-and-loop strap.
Disconnect both the high pressure hose and the garden
hose from the pump.
Neatly coil the high pressure hose and store with hook
and loop strap.
Tilt the unit as shown to allow any remaining water in the
pump to drain from the water inlet.
NOTICE:
The use of a pump protector is required after each use
and before storing to prevent cold weather and seal
damage during storage. Failure to use pump protector
will void your warranty.
Turn the spray wand counterclockwise to remove it from
the trigger handle. Store the unassembled spray wand
and trigger handle in their storage areas.
Store the unit and accessories in an area that does not
reach freezing temperatures. Do not store near furnace or
other sources of heat that could dry out the pump seals.
16 — English
Problem Possible Cause Solution
Pressure washer does not start
when trigger is depressed
Power cord not connected to power
source
The on/off switch is in the OFF
position (O)
GFCI is tripped
House/shop circuit breaker is tripped
Water pressure in hose
Connect the power cord to a live
120V AC, 60 Hz AC receptacle.
Put the on/off switch in the ON
position (I).
Press reset button on the GFCI
plug.
Reset house/shop breaker. Make
sure pressure washer is connected
to an individual branch circuit only. If
using an extension cord, make sure it
is heavy enough to carry the current
of the pressure washer.
Squeeze trigger to relieve water
pressure.
Pump doesn’t produce pressure Inadequate water supply
Trigger handle leaks
Nozzle is clogged
Pump is faulty
Air in line
Water inlet filter is clogged or dirty
Provide adequate water flow.
Check connections and / or replace
trigger handle.
Clean nozzle.
Contact authorized service center.
Squeeze trigger on trigger handle to
remove air from line.
Remove the water inlet filter, rinse
with warm water, then replace in unit.
Machine doesn’t reach high
pressure
Diameter of garden hose is too small
Water supply is restricted
Not enough inlet water
Hose is leaking
Kink in hose
Replace with 3/4 in. garden hose.
Check garden hose for kinks, leaks,
and blockages.
Open water source full force.
Replace hose.
Eliminate kinks in hose.
No detergent Soap tank is empty
Water supply is inadequate or
clogged
Wrong nozzle is attached
Add additional detergent to tank.
Check garden hose for kinks, leaks
and blockages.
Attach blue or black soap nozzle.
Wand leaks O-ring needs replacing Replace o-ring. If this does not
correct the problem, contact
your authorized service center to
purchase a new wand.
TROUBLESHOOTING
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
Ryobi RY141600 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Ryobi RY141600 User manual
- español: Ryobi RY141600 Manual de usuario