Bertazzoni MAST366RTBXT Manuel utilisateur

BERTAZZONI

INSTALLATION & USER MANUAL

GAS RANGETOP

3100515

WWW.BERTAZZONI.COM

2

/ Table of contents

TABLE OF CONTENTS

INSTALLATION

WARNINGS ___________________________________________________________________

DATA RATING LABEL ___________________________________________________________

BEFORE INSTALLATION ________________________________________________________

VENTILATION PREPARATION ____________________________________________________

SPECIFICATIONS ______________________________________________________________

CLEARENCE DIMENSIONS ______________________________________________________

INSTALLATION REQUIREMENTS _________________________________________________

Electrical ___________________________________________________________________

Gas ________________________________________________________________________

ELECTRICAL CONNECTION _____________________________________________________

WIRING DIAGRAM _____________________________________________________________

GAS CONNECTION _____________________________________________________________

Manual shut-oﬀ valve _________________________________________________________

Flexible connections __________________________________________________________

Pressure test-point stopper valve _______________________________________________

Pressure regulator ____________________________________________________________

INSTALLATION ________________________________________________________________

Unpackaging the rangetop_____________________________________________________

Installing the worktop frontguard ________________________________________________

Installing the island trim _______________________________________________________

Installing backguard (optional) __________________________________________________

GAS CONVERSION _____________________________________________________________

INSTALLATION CHECKLIST ______________________________________________________

FINAL PREPARATION ___________________________________________________________

BERTAZZONI SERVICE _________________________________________________________

USE ________________________________________________________________________

WARNINGS ____________________________________________________________________

WORKTOP AND KNOBS LAYOUT _________________________________________________

GAS COOKTOP ________________________________________________________________

ELECTRIC GRIDDLE ____________________________________________________________

KEEPING YOUR BERTAZZONI CLEAN _____________________________________________

TROUBLESHOOTING ___________________________________________________________

TWO YEARS LIMITED WARRANTY ________________________________________________

4

6

7

9

10

11

12

13

14

15

16

18

19

20

22

23

25

26

27

28

3

/ Models

Models

MAST366RTBXT

PROF366RTBXT

MAST366RTXE

MAST486GRTBXT

PROF486GRBXT

Models

4

/ Warnings

WARNINGS

To ensure proper and safe operation, the applian-

ce must be properly installed and grounded by a

qualiﬁ ed technician. DO NOT attempt to adjust,

repair, service, or replace any part of your ap-

pliance unless it is speciﬁ cally recommended in

this manual. All other servicing should be referred

to a qualiﬁ ed servicer. Have the installer show you

the location of the gas shutoﬀ valve and how to

shut it oﬀ in an emergency. A certiﬁ ed technician

is required for any adjustments or conversions to

Natural or LP gas.

FOR THE INSTALLER: Before installing the Ber-

tazzoni appliance, please read these instructions

carefully. This appliance shall be installed in ac-

cordance with the manufacturer’s installation in-

structions.

IMPORTANT: Leave these instructions with the

owner, who should save them for local inspector’s

use and for future reference. DO NOT remove

permanently aﬃ xed labels, warnings, or plates

from product. This may void the warranty.

Installation must conform with all local codes. In

the absence of codes:

• United States: installation must conform with

the National Fuel Gas Code ANSI Z223.1

INFPA54

• Massachusetts: All gas products must be

installed by a “Massachusetts” licensed

plumber or gasﬁ tter. A “T” type handle manual

valve must be installed in the gas supply line

to the appliance.

• Canada: Installation must be in accordance

with the current CAN/CGA B149.1 & 2 Gas

Installation codes and/or local codes. Electrical

installation must be in accordance with the

current CSA C22.1 Canadian Electrical Codes

Part 1 and/or local codes.

This rangetop is NOT designed for installation

in manufactured (mobile) homes or recreational

park trailers.

DO NOT install this range outdoors.

This appliance must be properly grounded.

Grounding reduces the risk of electric shock by

providing a safe pathway for electric current in the

event of a short circuit.

Warning!

To avoid risk of property damage, personal

injury or death; follow information in this ma-

nual exactly to prevent a ﬁ re or explosion.

WARNING!

If the information in these instructions is

not followed exactly, a ﬁ re or explosion may

result causing property damage, personal

injury or death.

- Do not store or use gasoline or other ﬂ ammable

vapors and liquid in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electrical switch.

•Do not use any phone in your building.

•Immediately call your gas supplier from a

neghbor’s phone. Follow the gas supplier’s

instructions.

•If you cannot reach your gas suppliers, call

the ﬁ re department.

- Installation and service must be performed by

a qualiﬁ ed installer, service agency or the gas

supplier

WARNING!

Never Operate the Top Surface Cooking

Section of this Appliance Unattended.

- Failure to follow this warning statement could

result in ﬁ re, explosion, or burn hazard that could

cause property damage. personal injury, or dea-

th.

- If a ﬁ re should occur, keep away from the

appliance and immediately call your ﬁ re depart-

ment.

DO NOT ATTEMPT TO EXTRINGUISH AN OIL/

GREASE FIRE WITH WATER

DANGER!!! ELECTRIC SHOCK HAZARD!!!

To avoid risk of electrical shock, personal injury

or death, verify that the appliance has been pro-

perly grounded in accordance with local codes or

in absence of codes, with the National Electrical

Code (NEC). ANSI/NFPA 70- latest edition.

DANGER!!! GAS LEAK HAZARD!!!

To avoid risk of personal injury or death, leak-te-

sting of the appliance must be conducted accor-

ding to the manufacturer’s instructions. Before

placing appliance in operation, always check for

gas leaks with water and soap solution.

DO NOT USE AN OPEN FLAME TO

CHECK FOR GAS LEAKS.

5

/ Warnings

WARNING:

Cancer and Reproductiv Harm-

www.P65Warnings.ca.gov

.

6

/ Data rating label / Before installation

The data rating label shows the model and serial

number of the rangetop. It is located under the

rangetop and in the last page of this manual.

• DO NOT remove permanently aﬃ xed labels,

warnings, or plates from product. This may

void the warranty.

• This appliance shall only be installed by an

authorized professi

onal.

• This appliance shall be installed in accordance

with the manufacturer’s installation

instructions.

• This appliance must be installed in accordance

with the norms & standards of the country

where it will be installed.

• The installation of this appliance must conform

to local codes and ordinances. In the absence

of local codes, Installations must conforms to

American National Standards, National Fuel

Gas Code ANSI Z223.1 – latest edition/NFPA

54 or B149.1.

• The appliance, when installed, must be

electrically grounded in accordance with local

codes or, in the absence of local codes, with

the National Electrical Code, ANSI/NFPA 70.

If local codes permit, a ﬂ exible metal appliance

connection conduit with the new AGA or CGA cer-

tiﬁ ed design, max. 5 feet (1,5 m) long, ½” I.D. is

recommended for connecting this appliance to the

gas supply line. Do not bend or damage the ﬂ exi-

ble connector when moving the appliance.

This appliance must be used with the pressure

regulator provided.

The regulator shall be properly installed in order to

be accessible when the appliance is installed in its

ﬁ nal location. The pressure regulator must be set

for the type of gas to be used. The pressure regu-

lator has ½” female pipe thread. The appropriate

ﬁ tting must be determined based on the size of

your gas supply line, the ﬂ exible metal connector

and the shutoﬀ valve.

The appliance must be isolated from the gas sup-

ply piping system by closing its individual manual

shutoﬀ valve during any pressure testing of the

gas supply piping system at test pressures equal

to or less than 1/2 PSI (13,8” w.c. or 3,5 kPa).

All opening and holes in the wall and ﬂ oor, back

and under the appliance shall be sealed before

installation of the appliance.

A manual valve shall be installed in an accessible

location in the gas line external to the appliance

for the purpose of turning on or shutting oﬀ gas to

the appliance.

Type of gas

This range can be used with Natural or LP/Pro-

pane gas. The range is shipped from the factory

for use with the gas indicated on the rating label

positioned on the lower face of the control panel

and in the last page of this manual. A step by step

conversion procedure is also included in this ma-

nual and in each conversion kit.

Gas pressure

The maximum inlet gas supply pressure inco-

ming to the gas appliance pressure regulator is

1/2 PSI (13,8’’ iwc or 3,5 kPa). The minimum gas

supply pressure for checking the regulator setting

shall be at least 1“ iwc (249 Pa) above the inlet

speciﬁ ed manifold pressure to the appliance; this

operating pressure is 4” iwc (1.00 kPa) for Natural

Gas and 10” iwc (2.50 kPa) for LP Gas.

Room ventilation

An exhaust fan may be used with the appliance;

in each case it shall be installed in conformity

with the appropriate national and local standards.

Exhaust hood operation may aﬀ ect other vented

appliances; in each case it shall be installed in

conformity with the appropriate national and local

standards.

Warning

This appliance should not be installed with a

ventilation system that directs air in a downward

direction toward the range. This type of ventila-

tion system may cause ignition and combustion

problems with the appliance resulting in personal

injury, property damage, or unintended operation.

Ventilating systems that direct the air upwards do

not have any restriction.

Do not use aerosol sprays in the vicinity of

this appliance while it is in operation.

DATA RATING LABEL

BEFORE INSTALLATION

7

This rangetop will best perform when installed

with Bertazzoni exhaust hoods. These hoods

have been designed to work in conjunction with

the Bertazzoni range and have the same ﬁ nish for

a perfect look.

Before installation of the exhaust hood, consult lo-

cal or regional building and installation codes for

additional speciﬁ c clearance requirements.

Refer to the rangetop hood installation instructions

provided by the manufacturer for additional infor-

mation.

Select Hood and Blower Models:

• For wall installations, the hood should be

equal or larger width than the range. Where

space permits, a hood larger than the range

may be desirable for improved ventilation

performance.

• For island installations, the hood width should

overhang the range by a minimum of 3” (76

mm) on each side.

Hood Placement:

• For best removal of smoke and odors, the

lower edge of the hood should be installed

between 25 1/2” (65 cm) and 31 1/2” (80 cm)

above the range cooking surface.

• If the hood contains any combustible materials

(i.e. a wood covering), it must be installed at a

minimum of 36” (914 mm) above the cooking

surface.

Consider Make-Up Air:

Due to the high volume of ventilation air, a sour-

ce of outside replacement air is recommended.

This is particularly important for tightly sealed

and insulated homes. A qualiﬁ ed heating and

ventilating contractor should be consulted.

/ Ventilation preparation / Speciﬁ cations

VENTILATION PREPARATION

SPECIFICATIONS

A

36’’ 48’’

A

27''

/8

25''

/16

36''

48''

7''

/85

7''

/85

22''

/16

23''

/4

9

5''

/161

1''

/169

25''

/16

2''

/21

13''

/16

1''

/85

20''

/8

5

2''

/21

1''

/16

11

1''

/85

24''

/16

9

8

/ Speciﬁ cations - Cabinet

Burner

Auxiliary

Semi-rapid

Rapid

Dual burner

Injector

diam.[mm]

0.90

0.54

1.18

0.70

1.55

0.92

0.80+2.10

0.50+1.20

Gas

Type

NG

LP (Propane)

NG

LP (Propane)

NG

LP (Propane)

NG

LP (Propane)

Pressure

[iwc]

4’’

10’’

4’’

10’’

4’’

10’’

4’’

10’’

Max Rate

[Btu/hr]

3,500

3,300

5,900

5,500

10,400

9,500

19,000

Min Rate

[Btu/hr]

900

1,500

2,500

1,300

[W]

1,025

967

1,729

1,611

3,047

2,783

5,567

[W]

264

439

732

381

By-pass

diam.[mm]

Regulated

0.29

Regulated

0.36

Regulated

0.47

Regulated

0.34/0.65

See use and care manual for the layout of the surface burners of your rangetop

B

urner In

j

ector

G

a

s

Pre

ss

ure Max Rate Min Rate

By

-pas

s

Cabinet Preparation

1. To ensure professional results, the cabinet and

countertop openings should be prepared by a

qualiﬁ ed cabinet worker.

2. The clearances shown in ﬁ gure are required.

3. The gas and electrical supply must be locat-

ed in an area that is accessible without requiring

removal of the cooktop. The appliance electrical

power cord and gas pipe connection are located

on the left rear.

• Prepare the ﬁ nished opening for the rangetop

according to dimensions shown in the

illustration on the follows page.

• The platform must include a cut-out at the right

rear for electrical and gas supply connections.

It must be level to ensure the cooking surface

is level. Refer to the chart below for minimum

base support.

BASE SUPPORT MIN

36” rangetop 250 lb (113 kg)

48” rangetop 300 lb (136 kg)

WARNING

To prevent possible damage to cabinets and ca-

binet ﬁ nishes, use only materials and ﬁ nishes that

will not discolor or delaminate and will withstand

temperatures up to 230°F (110°C). Heat resistant

adhesive must be used if the product is to be in-

stalled in laminated cabinetry. Check with your

builder or cabinet supplier to make sure that the

materials meet these requirements.

9

/ Clearence dimensions

CLEARENCES DIMENSIONS

Installation adjacent to kitchen cabinets

This range may be installed directly adjacent to

existing countertop high cabinets (36” or 91.5 cm

from the ﬂ oor).

For the best look, the worktop should be level with

the cabinet countertop. This can be accomplished

by raising the unit using the adjustment spindles

on the legs.

ATTENTION: the rangetop CANNOT be installed

directly adjacent to kitchen walls, tall cabinets, tall

appliances, or other vertical surfaces above 36”

(91.4 cm) high. The minimum side clearance in

such cases is 6” (15.2 cm).

Wall cabinets with minimum side clearance must

be installed 18” (45.7 cm) above the countertop

with countertop height between 35 ½” (90.2 cm)

and 37 ¼” (94.6 cm). The maximum depth of wall

cabinets above the rangetop shall be 13” (33.0

cm).

Cabinet

Shaded area behind range indicates minimum

clearance to combustible surfaces, combustible

materials cannot be located within this area.

12” (305 mm) min. to combustible surface with

Flush Island Trim

For Flush Island installations, counter surface

should have a cantilever edge meeting the back

section of the Flush Island Trim accessory.

As deﬁ ned in the “National Fuel Gas Code” (ANSI

Z223.1, Current Edition).

Clearances from non-combustible materials are

not part of the ANSI Z21.1

scope and are not certiﬁ ed by CSA. Clearances of

less than 12” (305 mm)

must be approved by the local codes and/or by

the local authority having jurisdiction.

Metal hood

A

B

C

D

E

F

G

L

B

H

36’ (91,5 cm) or 48” (122 cm)

36’’ (91,5 cm) hood with combustible materials

13’’ (33,0 cm)

18’’ (45,7 cm)

6’’ 5/8(16,8 cm)

6’ (15,2 cm)

min 3” 7/16 max 5” 3/16 (min 8,7cm max 13 cm)

25’’ 3/16(64 cm)

min 25” 1/2 (65 cm)

min 12” (30,50 cm)

B

H

A

F

D

B

C

E

G

F

L

10

/ Installation requirements / Electrical connection

ELECTRICAL

A properly-grounded horizontally- mounted electri-

cal receptacle should be installed no higher than

27” (68.6 cm) above the ﬂ oor, no less than 2” (5

cm) and no more than 15” (38,1 cm) from the left

side (facing product).

Check all local code requirements.

GAS

An agency-approved, properly-sized manual

shut-oﬀ valve should be installed no higher than

27” (68.6 cm) above the ﬂ oor and no less than 2”

(5 cm) and no more than 15” (38.1 cm) from the

right side (facing product).

To connect gas between shut-oﬀ valve and regula-

tor, use agency-approved, properly sized ﬂ exible

or rigid pipe. Check all local code requirements.

Warning!

ELECTRICAL SHOCK HAZARD

Disconnect electrical power at the circuit bre-

aker box or fuse box before installing the ap-

pliance.

Provide appropriate ground for the appliance.

Use copper conductors only.

Failure to follow these instructions could re-

sult in serious injury or death.

This unit is manufactured for a polarized, groun-

ded 120 volt/60 Hz, 16 amp system.

Electric power consumption is about 200 W for

36”, 1200W for 48”

The minimum of 102 VAC is required for proper

operation of gas ignition systems.

The circuit must be grounded and properly pola-

rized.

The unit is equipped with a SJT power cord and

a NEMA 5-15P plug. In case of replacement, the

power cord shall be replaced with one of the same

type, size and length.

Warning!

Electrical grounding

This appliance is equipped with a three-prong

plug for your protection against shock hazard and

should be plugged directly into a properly groun-

ded socket. Do not cut or remove the grounding

prong from this plug.

Caution

Label all wires prior to disconnecting when

servicing controls. Wiring errors can cause

improper and dangerous operation.

Verify proper operation after servicing.

INSTALLATION REQUIREMENTS ELECTRICAL CONNECTION

installation area for the connection

E

G

15'' 15''

27''

PLQPD[

11

/ Wiring diagram

WIRING DIAGRAM

The electric wiring diagrams and schematics are attached behind the rangetop, and should not be removed

except by a service technician, then replaced after service.

*

/

1

*9

0

6LPE 'HVFULSWLRQ

JU *UHHQHDUWK

Q %ODFNOLQH

EL :KLWHQHXWUDO

&2/2856

6LPE 'HVFULSWLRQ

,*1 ,JQLWLRQ0LFURVZLWFKHV

* 6SDUN*HQHUDWRU

/(*(1'$

EL

,*1

Q

*

/

1

*9

0

6LPE 'HVFULSWLRQ

U5HG

JU *UHHQHDUWK

Q %ODFNOLQH

EL :KLWHQHXWUDO

&2/2856

6LPE 'HVFULSWLRQ

,*1 ,JQLWLRQ0LFURVZLWFKHV

* 6SDUN*HQHUDWRU

*( *ULGGOH7KHUPRVWDW

5*5 *ULGGOHHOHPHQW

766 6DIHW\7KHUPRVWDW

/(*(1'$

EL

Q

EL

JY

EL

,*1

Q

5*5

766





6

*(

EL

Q

EL

U

D

U

Q

12

/ Gas connection

Warning!

DO NOT USE AN OPEN FLAME WHEN

CHECKING FOR LEAKS!

Leak testing of the appliance shall be conducted

according to the manufacturer’s instructions. Be-

fore placing the oven into operation, always check

for leaks with soapy water solution or other accep-

table method.

Check for gas leakage with soapy water solution or

other acceptable methods in all gas connections

installed between inlet gas pipe of the appliance,

gas regulator, till to the manual shut-oﬀ valve.

All gas connections must comply with national and

local codes. The gas supply line (service) must

be the same size or greater than the inlet line of

the appliance. This rangetop uses a 1/2” NPT inlet

(see drawing below for details of gas connection).

On all pipe joints use appropriate sealant resistant

to gas to joint the adapter to rangetop manifold

use only the blue gasket supplied.

If necessary, the appliance must be converted by

the dealer, by a factory-trained professional or by

a qualiﬁ ed licensed plumber or gas service com-

pany.

Gas conversion is important for safe and eﬀ ecti-

ve use of the appliance. It is the responsibility of

the dealer and the owner of the range to perform

the appropriate gas conversion following the di-

rections of the manufacturer.

THE GAS CONVERSION PROCEDURE IS

DESCRIBED IN THIS MANUAL AND IN THE

PACKAGE CONTAINING THE CONVERSION

NOZZLES SHIPPED WITH EVERY RANGETOP.

Please provide the service person with this ma-

nual before work is started on the rangetop.

MANUAL SHUT-OFF VALVE

THIS VALVE IS NOT SHIPPED WITH THE AP-

PLIANC AND MUST BE SUPPLIED BY THE IN-

STALLER.

The manual shut-oﬀ valve must be installed in the

gas service line between the gas hook-up on the

wall and the appliance inlet, in a position where it

can be reached quickly in the event of an emer-

gency.

In Massachusetts: A ‘T’ handle type manual

gas valve must be installed in the gas supply line

to this appliance.

FLEXIBLE CONNECTIONS

In case of installation with ﬂ exible couplings and/

or quick-disconnect ﬁ ttings, the installer must use

a heavy-duty, AGA design-certiﬁ ed commercial

ﬂ exible connector of at least 1/2” (1.3 cm) ID NPT

(with suitable strain reliefs) in compliance with

ANSI Z21.41 and Z21.69 standards.

In Massachusetts: The unit must be installed

with a 36” (3-foot) long ﬂ exible gas connector.

In Canada: use CAN 1-6.10-88 metal connec-

tors for gas appliances and CAN 1-6.9 M79 quick

disconnect device for use with gas fuel.

PRESSURE TEST-POINT STOPPER

VALVE

To avoid gas leaks, the pressure test-point stop-

per valve and gasket supplied with the rangetop

must be installed on the gas ﬁ tting at the back of

the rangetop according to the diagram below.

GAS CONNECTION

GAS PIPE

GASKET

PRESSURE TEST-POINT

STOPPER

GAS CONNECTION ADAPTOR

1/2’’NPT WITH PRESSURE TEST

POINT 1/8’’ NPT (TO BE FIXED

TOWARD EXTERNAL SIDE OF

THE APPLIANCE)

ELBOW

13

/ Gas connection

PRESSURE REGULATOR

Since service pressure may ﬂ uctuate with local

demand, every gas cooking appliance must be

equipped with a pressure regulator on the inco-

ming service line for safe and eﬃ cient operation.

The pressure regulator shipped with the applian-

ce has two female threads ½” NPT. The regulator

shall be installed properly in order to be accessible

when the appliance is installed in its ﬁ nal position.

Manifold pressure should be checked with a ma-

nometer and comply with the values indicated be-

low:

Natural gas 4.0” iwc

LP/Propane 10.0” iwc

Incoming line pressure upstream from the regula-

tor must be 1” iwc higher than the manifold pres-

sure in order to check the regulator.

The regulator used on this range can withstand a

maximum input pressure of 1/2 PSI (13,8” iwc or

3,5 kPa) If the line pressure exceeds that amount,

a stepdown regulator is required.

The appliance, its individual shut-oﬀ valve, and

the pressure regulator must be disconnected from

the gas line during any pressure testing of that sy-

stem at pressures in excess of 1/2 PSI (13,8” iwc

or 3,5 kPa).

The individuaL manual shut-oﬀ valve must be in

the OFF position during any pressure testing of

the gas supply piping system at test pressures

equal to or less than 1/2 PSI (13,8” iwc or 3,5 kPa).

Warning

Before carrying out any servicing operation di-

sconnect the appliance from gas and electric

supply and extra appliance from ﬁ nal installation

place in order to have access to the appliance for

proper servicing intervention.

14

/ Installation

APPLIANCE INSTALLATION

Unpacking the rangetop

• Remove all packing materials from the

shipping pallet but leave the adhesive-backed

foam layer over brushed-metal surfaces to

protect it from scratches until the range is

installed in its ﬁ nalposition. Only the ﬁ lm on

the side panels should be removed before

inserting the rangetop between the cabinets.

• Examine the appliance after unpacking it. In

the event of transport damage, do not plug

it. Take pictures of the damage and report it

immediately to the freight forwarder.

• The grates, griddle plate, burner caps, and

oven racks should be removed to facilitate

handling.

•

INSTALLING THE WORKTOP

FRONTGUARD

To increase the clearance between the front edge

of the worktop and the burners, it is possible to

install a front guard for the worktop.

To install the front guard,

• Locate the two ﬁ xing holes on the end of the

front guard.

• Locate the two ﬁ xing holes on the bottom facet

of the worktop

• Fix the front guard with it’s two screws

INSTALLATION

15

INSTALLING THE ISLAND TRIM

The island trim is only placed on the cooktop, re-

move all tape and packaging before installing it.

INSTALLING BACKGUARD (OPTIONAL)

The backguard is an optional contact you dealer

for buying it.

/ Installation

1 1

2 2

3

4 4

16

GAS CONVERSION

Warning!

Before carrying out this operation, disconnect the

appliance from gas and electricity.

Gas conversion shall be conducted by a fac-

tory-trained professional.

Call the customer service hotline to identify a fac-

tory-trained professional near your home.

The gas conversion procedure for this rangetop

includes 4 steps:

• Pressure regulator

• Surface burners

• Visual checks prior to closure of oven bottom

panel

• Adjustment of minimum setting

The conversion is not completed if all 4 steps have

not been concluded properly.

Before performing the gas conversion, locate the

package containing the replacement nozzle ship-

ped with every range.

IMPORTANT: Each nozzle has a number indica-

ting its ﬂ ow diameter printed on the body. Consult

the table number 1 for matching nozzles to bur-

ners.

Save the nozzles removed from the rangetop for

future use.

Step 1: pressure regulator

The pressure regulator supplied with the applian-

ce is a convertible type pressure regulator for use

with Natural Gas at a nominal outlet pressure of

4” iwc or LP gas at a nominal outlet pressure of

10”iwc. and it is pre-arranged from the factory to

operate with one of these gas/pressure as indica-

ted in the labels aﬃ xed on the appliance, package

and Instruction booklet.

To convert the regulator for use with the other gas:

Unscrew by hand the upper cap of the regula-

tor, remove the white plastic attachment from the

cap, reverse its direction and screw it again ﬁ rm-

ly against the cap. The white plastic attachment

has arrows indicating the position for natural gas

(NAT) and LP gas (LP).

Screw by hand the metal cap in the original posi-

tion on the regulator.

Step 2: surface burners

To replace the nozzles of the surface burners, lift

up the burners and unscrew the nozzles shipped

with the rangetop using a 7 mm (sochet wrench).

Replace nozzles using the conversion set sup-

plied with the rangetop or by a Bertazzoni authori-

zed parts warehouse. Each nozzle has a number

indicating its ﬂ ow diameter printed on the body.

Consult the table number 1 and matching nozzles

to burners.

/ Gas conversion

LP

NAT

17

Step 3: visula checks

Surface burners

The burner ﬂ ame color should be blue with no yel-

low on the tips. It is not uncommon to see orange

in the

ﬂ ame color; this indicates the burning of airborne

impurities in the gas and will disappear with use.

With propane (LP) gas, slight yellow tips on the

primary icone are normal.

The ﬂ ame should burn completely around the bur-

ner cap. If it doesn’t, check that the cap is posi-

tioned

correctly on the base and that the ports are not

blocked.

The ﬂ ame should be stable with no excessive noi-

se or ﬂ uttering.

After performing all these visual checks, reinstall

the bottom panel of the oven compartment and

proceed to setting the minimum for each burner.

Step 4: minimum ﬂ ame adjustment

WARNING!

These adjustments should be made only for use

of the appliance with natural gas. For use with li-

quid propane gas, the choke screw must be fully

turned in a clockwise direction.

SURFACE BURNERS

Light one burner at a time and set the knob to the

MINIMUM position (small ﬂ ame).

Remove the knob.

The rangetop is equipped with a safety valve.

Using a small-size slotted screwdriver, locate the

choke valve on the valve body and turn the choke

screw to the right or left until the burner ﬂ ame is

adjusted to desired minimum.

Make sure that the ﬂ ame does not go out when

switching quickly from the MAXIMUM to the MINI-

MUM position.

For the gas valve of dual burner the choke valve is

located on the valve body, the A screw adjust the

outer ring, the B screw adjust the inner ring.

/ Gas conversion

yellow ﬂ ames:

further adjustment is required

yellow tips on outer cones:

normal for LP gas

soft blue ﬂ ames:

normal for natural gas

A

B

18

INSTALLATION CHECKLIST FINAL PREPARATION

A qualiﬁ ed installer should carry out the following

checks:

Island trim or Backguard attached accor-

ding to instruction

Clearance to cabinet surfaces as manu-

facturer’s guideline

Proper ground connection

Gas service line connected following ma-

nufacturer’s guideline

Valves, stoppers and gasket installed

between the rangetop and the service line

Gas connection tested and free of gas

leaks

Rangetop settled for the type of gas avai-

lable in the household

Each burner lights satisfactorily, both indi-

vidually and with other burners operating

Flame appear sharp blue, with no yellow

tipping, shooting or ﬂ ame lifting

Minimum settled for all burners

• Before using the rangetop, remove any

protective wrap from the stainless steel.

• All stainless steel body parts should be wiped

with hot, soapy water and with a liquid stainless

steel cleanser.

• If buildup occurs, do not use steel wool,

abrasive cloths, cleaners, or powders!

• If it is necessary to scrape stainless steel to

remove encrusted materials, soak with hot,

wet cloths to loosen the material, then use a

wood or nylon scraper.

• Do not use a metal knife, spatula, or any other

metal tool to scrape stainless steel! Scratches

are almost impossible to remove..

/ Installation checklist / ﬁ nal preparation / Bertazzoni service

BERTAZZONI SERVICE

Bertazzoni is committed to providing the best cu-

stomer and product service. We have a dedicated

team of trained professionals to answer your ne-

eds.

If you own a Bertazzoni appliance and need ser-

vice in the US or Canada please use the following

contact information:

e-mail: [email protected]

Telephone - Monday through Friday,

7.30am to 7.30pm EST (except US public holidays).

US 866-905-0010

WESTERN CANADA 866-905-0010 (BC,AB,SK,MB)

EASTERN CANADA 800-561-7265 (ON,QC,NL,NB,NS,PE)

19

/User

BERTAZZONI

USER MANUAL

GAS RANGETOP

20

WARNINGS

Warning and Important Safety Instructions ap-

pearing in this manual are not meant to cover all

possible conditions and situations that may occur.

Common sense, caution, and care must be exer-

cised when installing, maintaining, or operating

the appliance.

Read and follow all instructions before using

this appliance to prevent the potential risk of

ﬁ re, electric shock, personal injury or damage

to the appliance as a result of improper usage

of the appliance. Use appliance only for its in-

tended purpose as described in this manual.

Save this Manual for local electrical inspector’s

use. Read and save these instructions for future

reference. Observe all governing codes, ordinan-

ces and regulations.

WARNING!

If the information in these instructions is not fol-

lowed exactly, a ﬁ re or explosion may result cau-

sing property damage, personal injury or death.

- Do not store or use gasoline or other ﬂ ammable

vapors and liquid in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas sup-

plier’s instructions.

• If you cannot reach your gas suppliers,

call the ﬁ re department.

- Installation and service must be performed by

a qualiﬁ ed installer, service agency or the gas

supplier

In Massachusetts:

All gas products must be installed by a “Massa-

chusetts” licensed plumber or gasﬁ tter. A “T” han-

dle type manual gas valve must be installed in the

gas line connected to this appliance.

To ensure proper and safe operation: Appliance

must be properly installed and grounded by a qua-

liﬁ ed technician. DO NOT attempt to adjust, repair,

service, or replace any part of your appliance un-

less it is speciﬁ cally recommended in this manual.

All other servicing should be referred to a qualiﬁ ed

servicer. Have the installer show you the location

of the gas shut-oﬀ valve and how to shut it oﬀ in

an emergency.

A certiﬁ ed technician is required for any adjust-

ments or conversions to Natural or LP gas.

To Prevent Fire or Smoke Damage

• Be sure all packing materials are removed

from the appliance before operating it.

• Never let clothing, potholders, or other

ﬂ ammable materials come in contact with or

too close to any element, top burner or burner

grate until it has cooled.

• If appliance is installed near a window, proper

precautions should be taken to prevent

curtains from blowing over burners.

• Never leave any items on the cooktop. The

hot air from the vent may ignite ﬂ ammable

items and may increase pressure in closed

containers which may cause them to burst.

• Many aerosol-type spray cans are EXPLOSIVE

when exposed to heat and may be highly

ﬂ ammable. Avoid their use or storage near an

appliance.

In Case of Fire

Turn oﬀ appliance and ventilation hood to avoid

spreading the ﬂ ame. Extinguish ﬂ ame then turn

on hood to remove smoke and odor.

• Cooktop: Smother ﬁ re or ﬂ ame in a pan with a

lid or cookie sheet.

• NEVER pick up or move a ﬂ aming pa

n.

Child Safety

• NEVER leave children alone or unsupervised

near the appliance when it is in use or is still

hot.

• NEVER allow children to sit or stand on any

part of the appliance as they could be injured

or burned.

• CAUTION do not store items of interest to

children in cabinets above the rangetop or

on the backguard of the rangetop. Children

climbing on the rangetop to reach those items

could be seriously injured.

/User Wrarning

La page charge ...

Bertazzoni MAST366RTBXT Manuel utilisateur

Bertazzoni MAST366RTBXT Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents