Hitachi Blower RB160EF Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

GB
DE
FR
IT
NL
ES
PT
SE
DK
NO
FI
RB160EF
GB
OWNER’S MANUAL
FR
MODE D’EMPLOI
IT
MANUALE D’ISTRUZIONI
DE
BEDIENUNGSANLEITUNG
ES
MANUAL DEL PROPIETARIO
NL
GEBRUIKSAANWIJZING
PT
MANUAL DO PROPRIETÁRIO
BACKPACK BLOWERS
TRAGBARER LUFTBESEN
SOUFFLANTE DORSALE
SOFFIATORE A ZAINO
RUGZAK-TYPE BLADBLAZER
SOPLADOR DE MOCHILA
SOPRADOR DE MOCHILA
FLÄKTAR
RYGBÅRET BLÆSER
BÆRBAR LØVBLÅSER
REPPUPUHALLIN
SE
Ägarhandbok
DK
BETJENINGSVEJLEDNING
NO
Bruksanvisning
FI
Omistajan opas
F
I
N
O
D
K
S
E
P
T
E
S
N
L
I
T
F
R
D
E
G
B
970-41908-201 2008.02
GB-1
G
B
RB160EF
OWNER’S MANUAL
BACKPACK BLOWERS
Read the manual carefully before
operating this machine.
GB-2
SOUND LEVEL VIBRATION LEVEL
ON HANDLE
ISO 11094
LwA
measured
guaranteed
ISO 7916
racing
MODEL
idling
RB160EF 64.9 cm
3
110 dB(A) 112 dB(A) 1.5 m/s
2
2.7 m/s
2
EXPLANATION OF SYMBOLS AND SAFETY WARNINGS
WARNING!!!
RISK OF DAMAGING HEARING
IN NORMAL CONDITIONS OF USE, THIS MACHINE
MAY INVOLVE A DAILY LEVEL OF PERSONAL EXPOSURE TO NOISE
FOR THE OPERATOR EQUAL TO OR GREATER THAN
85 dB(A)
Nikko Tanaka Engineering Co., LTD
:PTIJP0TBEB
%JSFDUPS
RB160EF

E180001
3-4-29 Tsudanuma Narashino Chiba, JAPAN
.BOVGBDUVSFEBU$IJCB+BQBO
GB-3
G
B
1. Parts location
1. Frame
2. Shoulder Strap
3. Spark Plug Cap
4. Throttle Lever
5. Ignition Switch
6. Net
7. Choke Lever
8. Air Cleaner
9. Volute Case
10. “CAUTION” Label
11. Elbow
12. Fuel Tank
13. Recoil Starter
SAFETY FIRST
Instructions contained in warnings within this manual marked
with a symbol concern critical points which must be taken
into consideration to prevent possible serious bodily injury, and
for this reason you are requested to read all such instructions
carefully and follow them without fail.
WARNINGS IN THE MANUAL
WARNING
This mark indicates instructions, which must be followed in
order to prevent accidents, which could lead to serious bodily
injury or death.
IMPORTANT
This mark indicates instructions, which must be followed, or it
leads to mechanical failure, breakdown, or damage.
NOTE
This mark indicates hints or directions useful in the use of the
product.
Contents
1. Parts location ...................................................3
2. Specifications...................................................4
3. Warning labels on the machine .......................4
4. Symbols on the machine..................................4
5. For safe operation............................................5
6. Set up...............................................................8
7. Fuel ..................................................................9
8. Operation .......................................................10
9. Maintenance ..................................................11
10. Storage...........................................................13
11. Troubleshooting guide ...................................14
GB-4
Model RB160EF
Dimensions (LxWxH) mm 371 x 464 x 495
Dry weight kg 10.5
Fuel tank capacity liter 2.1
Engine Type Air cooled 2-cycle gasoline engine
Displacement cm
3
64.9
Air Filter 2-stage fresh flow filter system
Carburetor Rotary
Ignition system C.D.I.
Spark plug NGK CMR7H (Noise-proof)
Muffler Spark arrester equipped
Operating Engine Speed rpm 2000 to 7100
Fuel Consumption liter/h 1.9
Average Air Volume (w/std Pipe)cu.m/min. 16.2
Maximum Air Volume (w/o Pipe) cu.m/min. 23.1
Max. Air Velocity m/sec. 90
Durability Period hrs. 300
Specifications are subject to change without notice.
2. Specification
3. Warning labels on
the machine
4. Symbols on the
machine
For safe operation and maintenance, symbols are
carved in relief on the machine. According to these in-
dications, please be careful not to make a mistake.
Read owners manual before oper-
ating this machine.
Wear head, eye and ear protection.
Warning / Attention
Keep all children, bystanders and helpers 15
meters away from the machine.
Never modify your machine.
We won’t warrant the machine, if you use the
remodeled blower or if you don’t observe
the
proper usage written in the manual.
If warning label peels off or becomes soiled
and impossible to read, you should contact
the dealer from which you purchased the
product to order new labels and affix them in
the required location(s).
The port to refuel “MIX GASOLINE”
Position:
FUEL TANK CAP
The direction to close the choke
Position:
ENGINE COVER
The direction to open the choke
Position:
ENGINE COVER
GB-5
G
B
1. Read this manual carefully un-
til you completely understand
and follow all safety and oper-
ating instructions.
2. Keep this manual handy so
that you may refer to it later
whenever any questions arise.
Also note, if you have any
questions which cannot be
answered herein, contact the
dealer from whom you pur-
chased the product.
3. Always be sure to include this
manual when selling, lending,
or otherwise transferring the
ownership of this product.
4. Do not lend or rent your ma-
chine without the owner's
manual.
5. Be sure that anyone using your
unit understands the infoma-
tion contained in this manual.
6. Never let a child under 13
years old use the machine.
WORKING CONDITION
1. Refrain from operating the
blower if you are tired, ill, or
upset, or if you are under the
influence of alcohol, drugs or
medication.
2. To reduce the risk of hearing
loss associated with sound
level(s), hearing protection is
required.
3. To reduce the risk of injury as-
sociated with thrown objects,
always wear eye protection
and foot protection. Eye pro-
tection should meet the re-
quirements of ANSI Z87.1.
4. To reduce the risk of injury as-
sociated with the inhalation of
dust, use a face filter mask in
dusty conditions.
5. Wear rubber-soled shoes or
shoes with some other form of
anti-slip protection to help pro-
tect you against falling.
6. To reduce the risk of injury
associated with objects be-
ing drawn into rotating parts,
do not wear loose clothing,
scarves, neck chains, uncon-
fined long hair, and the like.
7. Prolonged use of a blower,
exposing the operator to vibra-
tions and cold may produce
whitefinger disease (Raynaud’
s phenomenon), which symp-
toms are tingling and burning
sensations followed by loss of
color and numbness in the fin-
gers. All factors which contrib-
ute to whitefinger disease are
not known, but cold weather,
smoking diseases or physi-
cal conditions as well as long
periods of exposure to vibra-
tion are mentioned as factors.
In order to reduce the risk of
whitefinger disease, the follow-
ing precautions are strongly
recommended;
a) Keep your body warm. Never
use blower during rains.
b) Wear thick anti-vibration
gloves.
c) Take more than 5 minutes of
break in warm place frequent-
ly.
d) Maintain a firm grip at all
times, but do not squeeze the
handles with constant, exces-
sive pressures.
e) If you feel discomfort, redness
and swelling of your fingers or
any other part of your body,
see a doctor before getting
worse.
8. The ignition system of your unit
produces an electromagnetic
field of a very low intensity.
This field may interfere with
some pacemakers. To reduce
the risk of serious or fatal in-
jury, persons with pacemaker
should consult their physician
and the pacemaker manufac-
turer before operating this tool.
WORKING CIRCUMSTANCE
1. To reduce the risk of injury as-
sociated with exhaust fume
inhalation, do not operate in
unventilated area. The exhaust
gases contain harmful carbon
monoxide.
2. Avoid using the blower where
stable footing and balance are
not assured.
AVOID NOISE PROBLEM
NOTE
Check and follow the local regu-
lations as to sound level and
hours of operations for blower.
5. For safe operation
GB-6
in place. If any damage is found
in the fuel line, the exhaust line,
or the ignition wiring, do not use
the blower until it has been re-
paired.
IMPORTANT
• Before starting operation, al-
ways make sure to check if any
obstacles are left inside the vo-
lute case and net. The obstacles
may cause damage on fan and
volute case and serious injury.
WARNING
Check to see if the shock-
absorbing rubber mount has
become cracked or otherwise
damaged. Note that failing to
replace this rubber mount when
it has become cracked or dam-
aged may cause the engine to
come loose from its frame dur-
ing use, thus resulting in pos-
sible serious bodily injury.
If cracked, be sure to replace
without delay.
WARNING
To reduce the risk of injury asso-
ciated with contacting rotating
parts, stop the engine before
installing or removing attach-
ments. Do not operate without
net in place. Always disconnect
the spark plug before perform-
ing maintenance or accessing
movable parts.
USING THE PRODUCT
1. Check the work area that the
blower will be used in and re-
move or cover all valuables that
may be damaged by the air
blast or thrown debris.
2. To reduce the risk of injury as-
sociated with thrown objects.
a) Watch out for children, pets,
open windows or freshly washed
cars, and blow debris safely
away.
b) Use the full blower nozzle exten-
sion so the air stream can work
close to the ground.
c) Do not allow bystanders in work
area.
1. Operate power equipment only
at reasonable hours-not early
in the morning or late at night
when people might be dis-
turbed. Comply with times listed
in local ordinances.
2. To reduce sound levels, limit the
number of pieces of equipment
used at any one time.
3. Operate power blowers at the
lowest possible throttle speed to
do the job.
4. Check your equipment before
operation, especially the muffler,
air intakes and air filters.
WORKING PLAN
When planning your work
schedule, allow plenty of time
to rest. Limit the amount of time
over which the product is to
be used continuously to some-
where around 30 ~ 40 minutes
per session, and take 10 ~ 20
minutes of rest between work
sessions. Also try to keep the
total amount of work performed
in a single day under 2 hours or
less.
FUEL
WARNING
To reduce the risk of fire and burn
injury:
a) Handle fuel with care. It is highly
flammable.
b) Do not smoke while handing
fuel.
c) Do not refuel a hot engine.
d) Do not refuel a running engine.
e) Avoid spilling fuel or oil. Always
wipe unit dry before using.
f) Move at least 10 ft. (3 meters)
away from the fueling point be-
fore starting engine.
g) Always store gasoline in a con-
tainer approved for flammable
liquids.
h) Make sure the unit is properly
assembled and in good operat-
ing condition.
BEFORE STARTING THE
ENGINE
• Each time before starting the
engine, inspect the entire unit
to see if every part is in good
order and is securely tightened
5. For safe operation
GB-7
G
B
d) Do not point the blower nozzle
in the direction of people or
pets.
e) Always check to be sure that
no debris has been blown onto
someone else’s property.
f) Pay attention to the direction of
the wind, do not work against
the wind.
3. To minimize blowing time.
a) Use rakes and brooms to loosen
debris before blowing.
b) In dusty conditions, slightly
dampen surfaces or use mister
attachment when water is avail-
able.
c) Conserve water by using power
blowers instead of hoses for
many lawn and garden applica-
tions, including areas such as
gutters, screens, patios, grills,
porches and gardens.
4. Never to touch the spark plug or
plug cord while the engine is in
operation. Doing so may result
in being subjected to an electri-
cal shock.
5. Never to touch the muffler, spark
plug, or other metallic parts of
the engine while the engine is in
operation or immediately after
shutting down the engine. These
metallic parts reach high tem-
peratures during operation and
doing so could result in serious
burns.
6. After using blowers and other
equipment, CLEAN UP! Dispose
of debris in trash receptacles.
MAINTENANCE
1. In order to maintain your product
in proper working order, perform
the maintenance and check-
ing operations described in the
manual at regular intervals.
2. Always be sure to turn off the
engine and disconnect the
spark plug before performing
any maintenance or checking
procedures.
WARNING
The metallic parts reach high
temperatures immediately after
stopping the engine.
5. For safe operation
3. Examine the blower at intervals
for loose fasteners and rusted
or damaged parts. Use special
care around the fuel line, the
muffler, and the ignition wiring.
4. All engine service except for
those described in this manual
should be performed by compe-
tent service personnel. Improper
service to the blower fan and
muffler could cause a hazard-
ous failure.
5. When replacing the any other
part, or any lubricant, always be
sure to use only HITACHI prod-
ucts or products which have
been certified by HITACHI for
use with the HITACHI product.
6. In the event that any part must
be replaced or any maintenance
or repair work not described in
this manual must be performed,
please contact a representative
from the store nearest HITACHI
authorized servicing dealer for
assistance.
7. Do not use any accessory or
attachment other than HITACHI
recommended by manufacture.
8. Under no circumstances should
you ever take apart the product
or alter it in any way. Doing so
might result in the product be-
coming damaged during opera-
tion or the product becoming
unable to operate properly.
TRANSPORTATION
Drain the fuel from the fuel tank
before transporting or storing
the blower.
STORAGE
When storing the blower, choose
a space indoors free from mois-
ture and out of the reach of chil-
dren.
GB-8
6. Set up
BLOWER TUBES
1. Connect the blower and swivel joint with flexible
hose. Clamp both ends of the flexible hose securely
with the hardware supplied with the unit.
2. Align the protrusion and the groove provided on
the tube ends and twist the tube until connection is
locked up.
NOTE
A light lubricant may be used to ease assembly of flex-
ible pipe to blower elbow.
THROTTLE LEVER
Set up the clamp to the swivel and tighten the screw
on the clamp.
THROTTLE CABLE
Use the clamp to fasten the colgate tube containing
the throttle cable and the power cable to the hose.
WAIST BELT
The waist belt is attached to the rings on the left and
right sides of the frame.
Be sure to always tighten the buckle in front of your
body.
WARNING
If you are not using a waist belt, be sure to remove it
from the unit and store it.
There is a risk that the belt will be caught, toppling
the unit.
There is a danger that the belt will be sucked into
the fan.
(1) Clamp
(2) Swivel
(3) Screw
(1) Clamp
(2) Cable
(3) Hose
GB-9
G
B
Q
RECOMMENDED MIXING RATIO
GASOLINE 50 : OIL 1
<when using genuine oil>
Exhaust emission are controlled by the funda-
mental engine parameters and components (eq.,
carburation, ignition timing and port timing)
without addition of any major hardware or the
introduction of an inert material during com-
bustion.
These engines are certified to operate on unleaded
gasoline.
Make sure to use gasoline with a minimum octane
number of 89RON (USA/Canada: 87AL).
If you use a gasoline of a lower octane value than
prescribed, there is a danger that the engine tem-
perature may rise and an engine problem such as
piston seizing may consequently occur.
• Unleaded gasoline is recommended to reduce the
contamination of the air for the sake of your health
and the environment.
Poor quality gasolines or oils may damage sealing
rings, fuel lines or fuel tank of the engine.
Q
HOW TO MIX FUEL
• Pay attention to agitation.
1. Measure out the quantities of gasoline and oil to
be mixed.
2. Put some of the gasoline into a clean, approved
fuel container.
3. Pour in all of the oil and agitate well.
4. Pour in the rest of gasoline and agitate again for
at least one minute. As some oils may be difficult
to agitate depending on oil ingredients, sufficient
agitation is necessary for the engine to last long.
Be careful that, if the agitation is insufficient, there
is an increased danger of early piston seizing due
to abnormally lean mixture.
5. Put a clear indication on the outside of the con-
tainer to avoid mixing up with gasoline or other
containers.
6. Indicate the contents on outside of container for
easy identification.
Q
FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the cap on
a dustless place.
2. Put fuel into the fuel tank to 80% of the full capac-
ity.
3. Fasten the fuel cap securely and wipe up any fuel
spillage around the unit.
1. Select bare ground for fueling.
2. Move at least 10 feet (3 meters) away from the fu-
eling point before starting the engine.
3. Stop the engine before refueling the unit. At that
time, be sure to sufficiently agitate the mixed gas-
oline in the container.
Q
FOR YOUR ENGINE LIFE, AVOID:
1. FUEL WITH NO OIL (RAW GASOLINE) – It will
cause severe damage to the internal engine parts
very quickly.
2.
GASOHOL – It can cause deterioration of rubber
and/
or plastic parts and disruption of engine lubri-
cation.
3. OIL FOR 4-CYCLE ENGINE USE – It can cause
spark plug fouling, exhaust port blocking, or piston
ring sticking.
4.
Mixed fuels which have been left unused for a
period of one month or more
may clog the carbu-
retor and result in the engine failing to operate
properly.
5. In the case of storing the product for a long period
of time, clean the fuel tank after rendering it empty.
Next, activate the engine and empty the carbure-
tor of the composite fuel.
6. In the case of scrapping the used mixed oil con-
tainer, scrap it only at an authorized repository site.
• As for details of quality assurance, read the de-
scription in the section Limited Warranty carefully.
Moreover, normal wear and change in product
with no functional influence are not covered by the
warranty. Also, be careful that, if the usage in the
instruction manual is not observed as to the mixed
gasoline, etc. described therein, it may not be cov-
ered by the warranty.
7. Fuel
Q
FUEL
Gasoline is very flammable. Avoid smoking or
bringing any flame or sparks near fuel. Make
sure to stop the engine and allow it cool before
refueling the unit. Select outdoor bare ground for
fueling and move at least 3 m (10 ft) away from
the fueling point before starting the engine.
• The HITACHI engines are lubricated by oil specially
formulated for air-cooled 2-cycle gasoline engine
use. If genuine oil is not available, use an anti-
oxidant added quality oil expressly labeled for air-
cooled 2-cycle engine use(JASO FC GRADE OIL or
ISO EGC GRADE).
• Do not use BIA or TCW (2-stroke water-cooling type)
mixed oil.
WARNING
WARNING
WARNING
GB-10
NOTE
When the engine fails to start after several attempts
due to overchoking, open the choke and repeat
pulling the rope.
ADJUSTING IDLE SPEED
The idling speed is set for 2000 rpm at the factory.
If it is necessary to adjust the idle speed, use the
adjustment screw on the top side of carburetor.
STOPPING ENGINE
Move the throttle lever to the idling position and set
the ignition switch to the stop position.
(1)
NOTE
If the engine won’t stop when setting the ignition switch
to the stop position, close the choke lever and stop
the engine.
In this case, please repair the machine at your nealest
servicing dealer.
STARTING ENGINE
IMPORTANT
Avoid operating the blower with the flexible tube
and swivel joint disconnected. That will reduce the
cooling air and the engine could be damaged by
overheating.
1. Push the primer bulb until fuel flows out in the clear
tube.
2. When the engine is cool, close the choke.
3. Set the ignition switch to the start position.
(1)
(2)
(3)
(4)
4.Set the throttle lever in 1/3 open position.
5.To start, hold the top of the blower firmly with your
left hand. Pull the starter knob slowly until you feel it
engage and then give it a vigorous strong pull.
IMPORTANT
Avoid pulling the starter rope out to its full extent
and allowing the starter rope to snap back. This will
prevent premature damage to the starter.
Do not let a person stand near the blower or the ex-
haust port.
6.Once the engine is running, gradually open the
choke if it was set closed, and let the engine run at
idle speed for a minute to warm it up.
8. Operation
(1) Choke Lever
(2) Primer Bulb
(3) OPEN
(4) CLOSE
(1) Idling
Adjustment Screw
(1) Ignition Switch
(1) Full Throttle
(2) About 1/3 Open
(3) Idling
(4) Ignition Switch
(1) Choke Lever
(2) OPEN
(3) CLOSE
GB-11
G
B
Daily Every Every Every
System / Compronent Procedure or 25 hours 50 hours 100 hours
Before use after after after
Air Filter Prefilter Inspect / Clean

Air Filter Paper Filter Inspect / Replace
Fuel Leaks Inspect / Replace
Fuel Filter Inspect / Replace

Fuel Line Inspect / Clean
Spark Plug Inspect / Clean
Muffler Inspect / Clean
Muffler Spark Arrester Inspect / Clean
Cooling Systrem Inspect / Clean
Screws / Nuts / Bolts Tighten
Cylinder Exhaust Port Inspect / Clean
WARNING
Make sure that the engine has stopped and
is cool before performing any service to the
blower. Contact with rotating blower fan or
hot muffler may result in a personal injury.
AIR CLEANER
Never operate the blower without an air filter or with
a deformed or broken filter element.
Check the air cleaner before use.
A clogged air filter may increase fuel consumption
while cutting down the engine power. Never operate
the blower without the air filter or with a deformed fil-
ter element because unfiltered dusty air will quickly
ruin the engine.
CLEANING AIR FILTER:
1. Unscrew 2 knob bolts and remove the air cleaner
cover. Then remove a prefilter mounted inside the
air cleaner cover.
9. Maintenance
Maintenance, replacement, or repair of the emission control device and systems may be per-
formed by any non-road engine repair establishment or individual.
2. Wash the prefilter in fresh, non flammable cleaning
solution (ex. warm soapy water) and then dry.
(Clean the air filter once in a week.)
3. Exchange the paper filter element with new one in
case it has been contaminated.
WARNING
This prefilter is dry type.
Never wash the prefilter in oleaginous cleaning so-
lution.
FUEL FILTER
A clogged fuel filter may cause poor acceleration of
the engine. Check periodically to see if the filter is
clogged with dirt. The filter can be taken out of the
fueling port using a small wire hook. Disconnect the
filter assembly from the fuel pipe and unhook the re-
tainer to disassemble it. Clean the components with
gasoline.
(1) Screen (2) Element
(3) Holder (4) Retainer
(1) Knob Bolt
(2) Prefilter
(3) Paper Filter
GB-12
SPARK PLUG
The spark plug may gather carbon deposits on its
firing end with reasonable use. Remove and inspect
the spark plug every 25 hours and clean the elec-
trodes as necessary with a wire brush. The spark
gap should be adjusted to .025 in (0.6~0.7mm).
Plug manufacturers recommend replacing the plug
twice a year to avoid unexpected plug failure in a
job.
REPLACEMENT PLUG IS A CHAMPION
RZ7C OR NGK CMR7H.
IMPORTANT
Note that using any spark plugs other than those
designated may result in the engine failing to oper-
ate properly or in the engine becoming overheated
and damaged.
To install the spark plug, first turn the plug until it is
finger tight, then tighten it a quarter turn more with a
socket wrench.
MUFFLER
WARNING
Inspect periodically, the muffler for loose fasteners,
any damage or corrosion. If any sign of exhaust
leakage is found, do not use the blower and have it
repaired immediately.
Note that failing to do so may result in the engine
catching on fire.
IMPORTANT
Before starting operation, always make sure to
check if the muffler is properly held by three bolts to
the cylinder. (Fastening Torque : 8~12 N·m)
Even if one bolt out of three bolts is loose, the muf-
fler may get loose during operation which may result
in engine catching on fire.
PROCEDURES TO BE PERFORMED AFTER
EVERY 100 HOURS OF USE
1. Remove the muffler, insert a screwdriver into the
vent, and wipe away any carbon buildup. Wipe
away any carbon buildup on the muffler exhaust
vent and cylinder exhaust port at the same time.
2. Tighten all screws, bolts, and fittings.
SPARK ARRESTER
The muffler is equipped with a spark arrester to pre-
vent red hot carbon from flying out of the exhaust
outlet. Periodically inspect and clean as necessary
with a wire brush. In the State of California it is re-
quired by law (Section 4442 of the California Pulic
Resources Code) to equip a spark arrester when
a gas powered tool is used in any forest covered,
bush covered, or grass covered unimproved land.
(1) Three Bolts
(2) Spark Arrester
9. Maintenance
GB-13
G
B
9. Maintenance
AIR INLET NET
IMPORTANT
Blowing air is taken in from the air inlet net. When air
flow has dropped down during operation, stop the
engine and inspect the air inlet net for blocking by
obstacles.
Note that failure to remove any such obstacles may
result in the engine becoming overheated and dam-
aged.
(1) Net
WARNING
Never use the blower without the net of the blower.
Before each use, check that the net is attached in
place and is free from any damage.
IGNITION COIL AIR GAP INSPECTION
If the gap is out of standard or when installing the
coil or rotor, adjust the air gap between the ignition
coil and the iron core of the rotor.
Air Gap:
0.40mm (0.35 ~ 0.45mm)
0.016" (0.014 ~ 0.017")
(1) Rotor
(2) Ignition coil
10. Storage
BEFORE STORING THE BLOWER:
1. Drain a fuel tank and push the primer bulb until it
becomes empty of fuel.
2. Remove the spark plug and drop a spoonful of
2-cycle oil into the cylider. Crank the engine several
times and install the spark plug.
3. Store unit in a dry, dust free place, out of the reach
of children.
GB-14
11. Troubleshooting guide
Case 1. Starting failure
CHECK PROBABLE CAUSES ACTION
fuel tank
A
incorrect fuel
A
drain it and use correct fuel
fuel filter
A
fuel filter is clogged
A
clean
carburetor adjustment screw
A
out of normal range
A
adjust to normal range
sparking (no spark)
A
spark plug is fouled/wet
A
clean/dry
A
plug gap is incorrect
A
correct (GAP: 0.6 ~ 0.7 mm)
spark plug
A
disconnected
A
retighten
Case 2. Engine starts but does not keep running/hard re-starting
CHECK PROBABLE CAUSES ACTION
fuel tank
A
incorrect fuel or staled fuel
A
drain it and use correct fuel
carburetor adjustment screw
A
out of normal range
A
adjust to normal range
muffler, cylinder (exhaust port)
A
carbon is built-up
A
wipe away
air cleaner
A
clogged with dust
A
wash
cylinder fin, fan cover
A
clogged with dust
A
clean
When your unit seems to need further service, please consult with our HITACHI service shop in your area.
DE-1
D
E
RB160EF
BEDIENUNGSANLEITUNG
Lesen Sie vor der Verwendung
diese Anleitung sorgfältig durch.
TRAGBARER LUFTBESEN
DE-2
ERLÄUTERUNG DER SYMBOLE UND SICHERHEITSHINWEISE
WARNUNG!!!
HÖRSCHADEN-RISIKO
UNTER NORMALEN ANWENDUNGSBEDINGUNGEN
KANN DIESES GERÄT DIE BEDIENUNGSPERSON
EINEM TÄGLICHEN GERÄUSCHPEGEL VON
85 dB(A)
ODER HÖHER AUSSETZEN.
GERÄUSCHPEGEL
VIBRATIONSPEGEL
AUF HANDGRIFF
ISO 11094
LwA
gemessen garantiert
ISO 7916
Vollgas
MODELL
Leerlauf
RB160EF 64.9 cm
3
110 dB(A) 112 dB(A) 1.5 m/s
2
2.7 m/s
2
Nikko Tanaka Engineering Co., LTD
:PTIJP0TBEB
%JSFLUPS
RB160EF
1/1/2008
E180001
3-4-29 Tsudanuma Narashino Chiba, JAPAN
EEC
&STUFMMUJO$IJCB+BQBO
DE-3
D
E
SICHERHEIT ZUERST
,QGLHVHP+DQGEXFKEHÀQGHQVLFK:DUQKLQZHLVHGLHPLWGHP
Symbol gekennzeichnet sind. Diese beziehen sich auf be-
sonders kritische Gefahrenpunkte. Um schwere Verletzungen
]XYHUPHLGHQPVVHQGLHHQWVSUHFKHQGHQ6LFKHUKHLWVDQ
weisungen sorgfältig gelesen und befolgt werden.
WARNHINWEISE IN DIESEM HANDBUCH
WARNUNG
'LHVHV 6\PERO ZHLVW DXI$QZHLVXQJHQ KLQ GLH ]XU 9HUPHLG-
XQJYRQ8QIlOOHQ EHIROJW ZHUGHQ PVVHQGLH]XVFKZHUHQ
9HUOHW]XQJHQRGHU7RGIKUHQN|QQWHQ
WICHTIG
'LHVHV6\PEROZHLVWDXI$QZHLVXQJHQKLQGLH]X EHIROJHQ
VLQGXP)HKOHU$XVIlOOHRGHU6FKlGHQDP*HUlW]XYHUPHL-
den.
HINWEIS
'LHVHV6\PEROZHLVWDXI7LSSVXQG$QPHUNXQJHQKLQGLHIU
GHQ*HEUDXFKGHV*HUlWVQW]OLFKVHLQN|QQHQ
Inhalt
1. Anordnung der Teile.........................................3
2. Technische Daten ............................................4
3. Warnschilder am Gerät ....................................4
4. Symbole auf dem Gerät...................................4
5. Sicherheitshinweise .........................................5
6. Vorbereitung.....................................................8
7. Kraftstoff ..........................................................9
8. Betrieb............................................................10
9. Wartung..........................................................11
10. Aufbewahrung................................................13
11. Störungssuche...............................................14
1. Anordnung der Teile
1. Rahmen
2. Schultergurt
 =QGNHU]HQVWHFNHU
4. Gashebel
 =QGVFKDOWHU
6. Netz
7. Starterklappenhebel
 /XIWÀOWHU
9. Spiralgehäuse
 :DUQVFKLOGÅ9256,&+7´
 .QLHVWFN
12. Kraftstofftank
13. Seilzugstarter
DE-4
2. Technische Daten
3. Warnschilder am
Gerät
4. Symbole auf dem
Gerät
Auf dem Gerät sind Symbole für Sicherheitsfunktionen und
für die Wartung eingeprägt. Bitte diese Symbole beachten,
um Fehler zu vermeiden.
Kinder, Zuschauer und Mitarbeiter müssen immer
mindestens 15 Meter vom Gerät entfernt sein.
Einlassöffnung zum Nachfüllen von „MIX
GASOLINE“
Position:
KRAFTSTOFFBEHÄLTERDECKEL
Schließrichtung des Chokes
Position:
LUFTFILTERABDECKUNG
Richtung zum Öffnen des Chokes
Position:
LUFTFILTERABDECKUNG
Wenn sich Warnschilder ablösen oder verschmutzt
und unleserlich werden, neue Warnschilder beim
Händler bestellen und diese an der entsprechen-
den Stelle bzw. an den entsprechenden Stellen.
Niemals irgendwelche Änderungen am Gerät
vornehmen.
Bei Verwendung eines modifizierten Gebläse
oder bei Missachtung der in der Bedienungs-
anleitung beschriebenen sachgemäßen Ver-
wendung verfällt die Garantie für dieses Gerät.
Bitte vor der Arbeit mit diesem Gerät
die
Bedienungsanleitung sorgfältig
lesen.
Immer Helm, Schutzbrille
und Gehörschutz tragen.
Warnung/Achtung
Modell RB160EF
Abmessungen (LxBxH) mm 371 x 464 x 495
Nettogewicht kg 10,5
Kraftstofftank-Volumen Liter 2,1
Motortyp Luftgekühlter 2-Takt Benzinmotor
Hubraum ccm 64,9
Luftfilter Zweistufiges Frischstrom-Filtersystem
Vergaserventiltyp (Membran) Drehschieber
Zündsystem C.D.I.
Zündkerzen NGK CMR7H (mit Rauschunterdrückung)
Auspufftopf Ausgerüstet mit Funkenfänger
Motor-Betriebsdrehzahl /min. 2000 bis 7100
Kraftstoffverbrauch Liter/S 1,9
Durchschnittlicher Luftdurchsatz (mit Standardrohr)
m
3
/min. 16,2
Maximale Luftfördermenge (ohne Rohr) m
3
/min. 23,1
Maximale Luftstromgeschwindigkeit m/sek. 90
Haltbarkeitsdauer Stunden 300
Technischen Daten können ohne Vorankündigung geändert werden.
DE-5
D
E
Faktoren sind noch nicht bekannt,
wobei jedoch kaltes Wetter,
Raucherkrankungen, die physischen
Bedingungen sowie die lange Aus-
setzung zu Vibrationen als die Ursa-
chen angesehen werden. Um das
Risiko von Weißfingererkrankung zu
reduzieren, werden die folgenden
Vorsichtsmaßregeln dringend emp-
fohlen:
a) Halten Sie Ihren Körper warm. Ver-
wenden Sie den Luftbesen niemals
im Regen.
b) Tragen Sie dicke Handschuhe,
welche die Vibrationen bedämpfen.
c) Legen Sie häufig Rastpausen von
mindestens 5 Minuten an einem
warmen Ort ein.
d) Achten Sie immer auf festen Griff,
wobei Sie jedoch die Hebel nicht
mit konstantem und übermäßigem
Druck betätigen sollten.
e) Falls Sie Unbehagen, Röte und An-
schwellen Ihrer Finger oder anderer
Teile Ihres Körpers spüren, wenden
Sie sich an einen Arzt, um schlim-
meren Erkrankungen vorzubeugen.
8. Die Zündanlage Ihres Gerätes er-
zeugt ein elektromagnetisches Feld
sehr niedriger Intensität. Dieses Feld
kann manche Herzschrittmacher
beeinträchtigen. Um das Risiko ern-
sthafter oder fataler Verletzungen
zu reduzieren, sollten Personen mit
einem Herzschrittmacher einen Arzt
bzw. den Hersteller des Herzschrit-
tmachers konsultieren, bevor sie
dieses Werkzeug verwenden.
ARBEITSUMFELD
1. Um das Risiko von Verletzungen auf-
grund eines Einatmens der Abgase
zu reduzieren, betreiben Sie dieses
Gerät niemals an einem Ort mit
schlechter Belüftung. Die Abgase
enthalten giftiges Kohlenmonoxyd.
2. Vermeiden Sie eine Verwendung
des Luftbesens, wenn kein stabiler
Stand bzw. kein stabiles Gleichge-
wicht gewährleistet wird.
VERMEIDEN SIE GERÄUS-
CHPROBLEME
HINWEIS
Überprüfen und befolgen Sie die
örtlichen Vorschriften hinsichtlich des
zulässigen Geräuschpegels und der
zulässigen Betriebsstunden des Luft-
besens.
1. Bitte dieses Handbuch sorgfältig
durchlesen und alle Sicherheits-
hinweise und Bedienungsanwei-
sungen befolgen.
2. Das Handbuch stets griffbereit
halten, um bei Fragen rasch nach-
schlagen zu können. Fragen, die
in diesem Handbuch nicht beant-
wortet werden, bitte notieren und
beim Zenoah-Händler erfragen.
3. Dieses Gerät darf nur zusammen
mit dem Handbuch verkauft, ver-
liehen oder anderweitig weiterge-
geben werden.
4. Verleihen oder vermieten Sie nie-
mals Ihre Maschine, ohne die Be-
dienungsanleitung mitzugeben.
5. Stellen Sie sicher, dass jede Per-
son, die Ihr Gerät verwendet, die
in dieser Anleitung enthaltenen
Informationen versteht.
6. Lassen Sie niemals ein weniger
als 13 Jahre altes Kind diese
Maschine verwenden.
ARBEITSBEDINGUNGEN
1. Bedienen Sie niemals diesen Luft-
besen, wenn Sie müde, krank oder
aufgeregt sind bzw. unter dem
Einfluss von Alkohol, Drogen oder
Medikamenten stehen.
2. Um das Risiko von Gehörschäden
aufgrund des hohen Geräuschpe-
gels dieses Luftbesens zu vermei-
den, tragen Sie immer einen Ge-
hörschutz.
3. Um das Risiko von Verletzungen
aufgrund von weg geschleuderten
Objekten zu reduzieren, tragen Sie
immer eine Schutzbrille und gee-
igneten Schutz für die Füße. Die
Schutzbrille sollte den Anforderun-
gen der ANSI Z87.1 entsprechen.
4. Um das Risiko von Verletzungen
aufgrund von Einatmung von Staub
zu vermeiden, tragen Sie unter
staubigen Bedingungen immer eine
Gesichtsfiltermaske.
5. Tragen Sie Schuhe mit Gum-
misohlen oder anderem Schutz
gegen Rutschen, um Sie vor Umfall-
gefahr zu schützen.
6. Um das Risiko von Verletzungen
aufgrund von in die drehenden
Teile angesaugten Objekten zu re-
duzieren, tragen Sie niemals lose
Kleidung, Kopftücher, Halsketten,
ungewöhnlich lange Haare usw.
7. Längerer Verwendung des Luft-
besens, bei welcher die Bedien-
ungsperson Vibrationen oder Kälte
ausgesetzt ist, kann zu Weißfinger-
erkrankung (Raynaud-Syndrom)
führen, deren Symptome Prickeln
und Brennen gefolgt von Farbverlust
und Erstarrung der Finger sind. Alle
zu der Weißfingererkrankung beitra-
genden
5. Sicherheitshinweise
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156

Hitachi Blower RB160EF Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à