TEKTELIC Communications T0004471 Manuel utilisateur

Marque
TEKTELIC Communications
Modèle
T0004471
Taper
Manuel utilisateur
Confidential: This document is TEKTELIC Communications Inc. confidential information. Possession or
distribution of this document requires TEKTELIC Communications Inc. consent.
TEKTELIC COMMUNICATIONS INC.
Document Type:
User Manual
Document Number:
T0004280_UM
Document Version:
1.4
Product Name:
Kona Pico Gateway
Product Number:
T0004313, T0004471
Revision History
Version
Date
Status
Author
Change Description
0.1
Dec 02, 2016
Preliminary
A.Naryanan
Initial Release
0.2
Dec 06, 2016
Released
A.Naryanan
Updated as per review comments
1.0
Jul 31, 2017
Pending
Review
Z. Herasymiuk
Updates for Certification
1.1
Aug 8, 2017
Released
Z. Herasymiuk
Updated as per review comments
1.2
Sep 20, 2017
Released
Z. Herasymiuk
Required updates for Certification
1.3
Sep. 22, 2017
Released
Z. Herasymiuk
Formatting updates
1.4
Sep. 25, 2017
Released
A.Narayanan
Corrected part number table
User Manual T0004280_UM Version 1.4
TEKTELIC Communications Inc. Confidential Page 2 of 8
Table of Contents
What’s In The Box ................................................................................................................................................... 3
Specifications .......................................................................................................................................................... 3
System Requirements ............................................................................................................................................. 3
Connecting and Configuring your Gateway ............................................................................................................ 3
Gateway Rear Panel ................................................................................................................................................ 5
Gateway Front Panel ............................................................................................................................................... 5
Compliance Statements .......................................................................................................................................... 7
User Manual T0004280_UM Version 1.4
TEKTELIC Communications Inc. Confidential Page 3 of 8
What’s In The Box
Tektelic Pico Gateway (see table below for breakdown of available configurations)
AC Power Adapter
3-foot Ethernet Cable
External Antenna
Part Number
ISM Band
WiFi Enabled
T0004313
902-928 MHz
Yes
T0004471
902-928 MHz
No
Specifications
AC power adapter
o 120V AC, 60Hz, 0.4A input, 5V DC, 2A output
Operating temperature: 0 to 40°C
Indoor use only, do not connect to outdoor antennas or outdoor network cables
System Requirements
Requires internet access via an RJ45 cable connection or Wi-Fi connectivity (802.11 b/g/n at 2.4 GHz)
Requires continuous access to a standard 120V, 60Hz AC power outlet
Connecting and Configuring your Gateway
Connect the provided power adapter and, when applicable, the external antenna to the gateway
1
The gateway starts up as soon as power is applied, expect to see a solid green LED on the back RJ45
right LED
If you choose to access the internet via an RJ45 cable connection:
Connect the Ethernet cable from your Gateway to a LAN port on your router
o The Gateway is configured for DHCP, you should see activity indicated on the left RJ45 LED
after a few moments
The Gateway is ready for use
If you choose to access the internet via a Wi-Fi connection:
Use a Wi-Fi client (eg. smart phone) and connect to the KonaPicoAP_#SN access point within the first
minute of powering up the gateway (while the Wi-Fi LED is blinking)
Browse to http://192.168.10.1 to view a webpage allowing connection to your Wi-Fi network
Select your SSID and enter your passphrase, allowing your gateway to connect to your network as a
client
1
Use the gateway only with the provided power supply and Antenna
User Manual T0004280_UM Version 1.4
TEKTELIC Communications Inc. Confidential Page 4 of 8
o You should see the Wi-Fi LED stop blinking and stay lit once the gateway is connected to the
network
Gateway is then ready for use
If need to change the Wi-Fi network to which the gateway is connected:
Power cycle the gateway and use the same procedure described above to connect to a new Wi-Fi
network.
User Manual T0004280_UM Version 1.4
TEKTELIC Communications Inc. Confidential Page 5 of 8
Gateway Rear Panel
1. Ethernet activity LED – RJ45 left LED will flash when there is Ethernet activity
2. Gateway Power LED – RJ45 right LED will be solid when the gateway power supply is plugged in
3. 5V power connector
4. LoRa External Antenna connector (model dependant), use only provided antenna
Gateway Front Panel
1. System Status LED – as opposed to a simple power indicator, as with the RJ45 power LED on the back
side:
LED flashes at a high rate while the gateway is obtaining an IP address via DHCP
LED is solid on after the gateway has obtained an IP address via DHCP, and remains solid on
during normal operation
The LED flashes at a slow rate if the gateway is unable to obtain an IP address via DHCP, the
network is not connected, or some other problem prevents normal operation
2. LoRa Activity LED – flashes with the receipt of packets:
3
1
2
2
1
4
3
User Manual T0004280_UM Version 1.4
TEKTELIC Communications Inc. Confidential Page 6 of 8
The LED is lit briefly whenever an uplink packet received via the LoRaWAN is sent to the network
server
The LED is lit briefly whenever a downlink packet received from the network server is
transmitted via the LoRaWAN
3. Wi-Fi Activity LED – indicates the state of Wi-Fi connection:
LED flashes when the Wi-Fi access point (KonaPicoAP_#SN) is enabled
LED is solid on when the gateway is connected to a Wi-Fi network
User Manual T0004280_UM Version 1.4
TEKTELIC Communications Inc. Confidential Page 7 of 8
Compliance Statements
Federal Communications Commission
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
To comply with FCC/IC RF exposure limits for general population /
uncontrolled exposure, the antenna(s) used for this transmitter
must be installed to provide a separation distance of at least 20
cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
Industry Canada
This Device complies with Industry Canada License-exempt RSS
standard(s). This digital apparatus does not exceed the Class B
limits for radio-noise emissions from digital apparatus as set out
in the Radio Interference Regulations of the Canadian
Department of Communications ICES-003(B). Operation is
subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including
interference that may cause undesired operation of the
device.
This radio transmitter 22504-T0004280 has been approved by
Industry Canada to operate with the antenna listed below with
the maximum permissible gain or lesser and required antenna
impedance for the antenna indicated. Antenna types not
included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this
device.
This device complies with IC radiation exposure limits set forth
for an uncontrolled environment. This device should be installed
and operated with minimum distance 20cm between the radiator
and your body.
This device has been designed to operate with the antenna listed
below, and having a maximum gain of 2.7 dBi. Antennas not
included in this list or having a gain greater than 2.7 dBi are
strictly prohibited for use with this device. The required antenna
impedance is 50 ohms.
ET830DBLTRPSMA – Airgain, Inc.
User Manual T0004280_UM Version 1.4
TEKTELIC Communications Inc. Confidential Page 8 of 8
Industrie Canada (French)
Cet appareil est conforme aux normes RSS exemptées de licence
d'Industrie Canada. Cet appareil numérique ne dépasse pas les
limites de la classe B pour les émissions de bruit radio des
appareils numériques, tel qu'énoncé dans le Règlement sur le
brouillage radioélectrique du ministère des Communications du
Canada NMB-3(B). L'opération est soumise aux deux conditions
suivantes :
1. Cet appareil ne doit pas provoquer d'interférence, et
2. Cet appareil doit accepter toute interférence, y compris
les interférences susceptibles de provoquer un
fonctionnement indésirable de l'appareil.
Cet émetteur radio 22504-T0004280 a été approuvé par Industrie
Canada pour fonctionner avec l'antenne indiquée ci-dessous avec
le gain maximal admissible ou inférieur et l'impédance d'antenne
requise pour l'antenne indiquée. Les types d'antenne non inclus
dans cette liste, ayant un gain supérieur au gain maximal indiqué
pour ce type, sont strictement interdits pour être utilisés avec cet
appareil.
Cet appareil est conforme aux limites IC d'exposition aux
rayonnements définies pour un environnement non contrôlé. Cet
appareil doit être installés et utilisés avec distance minimum de
20cm entre le radiateur et votre corps.
Cet appareil a été conçu pour fonctionner avec l'antenne
indiquée ci-dessous et ayant un gain maximal de 2,7 dBi. Les
antennes non comprises dans cette liste ou ayant un gain
supérieur à 2,7 dBi sont strictement interdites pour être utilisées
avec cet appareil. L'impédance d'antenne requise est de 50 ohms.
ET830DBLTRPSMA – Airgain, Inc.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

TEKTELIC Communications T0004471 Manuel utilisateur

Marque
TEKTELIC Communications
Modèle
T0004471
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents