Danby DPA060B1WDB Le manuel du propriétaire

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL PROPIETARIO

*

Printed in China

Imprimé en Chine

Impreso en China

*Trademark of Danby Products

* Marque de commerce de Danby Products

* Marca comerciales de Danby Products

Danby Products Limited, Guelph, Ontario, Canada N1H 6Z9

Danby Products Inc. Findlay, Ohio, U.S.A. 45840

www.Danby.com

MODEL • MODÈLE • MODELO

DPA060B1WDB

DPA080B1WDB-6

DPA103B1WDB-6

2022.10.27

PORTABLE AIR CONDITIONER

Owner’s Manual.............................1 - 23

CLIMATISEUR PORTABLE

Manuel du propriétaire.................24 - 46

AIRE ACONDICIONADO PORTÁTIL

Manual del propietario.................47 - 69

1

Welcome to the Danby family.

We are proud of our quality products and we believe in dependable service. We suggest

that you read this owner’s manual before plugging in your new appliance as it contains

important operation information, safety information, troubleshooting, and maintenance tips

to ensure the reliability and longevity of your appliance.

You are entitled to the warranty coverage as described in the owner’s manual provided with

your new appliance.

1. Please write down your appliance information below. You must keep the original proof

of purchase receipt to validate and receive warranty services.

2. Register your product online and receive a FREE 2 MONTH WARRANTY EXTENSION

after ﬁ lling out a product survey, at www.danby.com/support/product-registration/

Need Help?

1. Read your Owner’s Manual for installation help, troubleshooting, and maintenance

assistance.

2. Visit www.Danby.com to access self-service tools, FAQs and much more by searching

your model number in the search bar.

3. For the Quickest Customer Service, please ﬁ ll out the web form at www.danby.com/

support. Your submission will go directly to an expert on your particular appliance.

Our average response times are between 20 minutes and 2 hours, during EST business

hours.

4. Call 1-800-263-2629 - please note that during peak hours, hold times can exceed one

hour.

Model Number: ____________________________________________________

Serial Number: ____________________________________________________

Date of Purchase: __________________________________________________

SAVE THESE INSTRUCTIONS!

CAUTION: RISK OF FIRE

Flammable refrigerant used. When maintaining

or disposing of the air conditioner, the refrigerant

must not be allowed to vent into the open air.

WARNING Shows that the appliance uses a ﬂ ammable refrigerant. If the

refrigerant leaks and is exposed to an external ignition source, there is

a risk of ﬁ re.

CAUTION Shows that the operation manual should be read carefully.

CAUTION Shows that service personnel should be handling this equipment with

reference to the installation manual.

CAUTION Shows that the information is available such as the operating manual

or the installation manual.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

SAFETY PRECAUTIONS

WARNING

• Installation must be performed according to the installation instructions. Improper installation can cause

water leakage, electrical shock or ﬁ re.

• Use only the included accessories and parts and speciﬁ ed tools for the installation. Using non-standard

parts can cause water leakage, electrical shock, ﬁ re and injury or property damage.

• Make sure that the outlet you are using is grounded and has the appropriate voltage. The power cord

is equipped with a three-prong grounding plug to protect against shock. Voltage information can be

found on the nameplate of the unit.

• You unit must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is

not adequately grounded or protected by a time delay fuse or circuit breaker (the fuse of circuit breaker

needed is determined by the maximum current of the unit. The maximum current is indicated on the

nameplate located on the unit), have a qualiﬁ ed electrician install the proper receptacle.

• Install the unit on a ﬂ at, sturdy surface. Failure to do so could result in damage or excessive noise and

vibration.

• The unit must be kept free from obstruction to ensure proper function and to mitigate safety hazards.

• Do not modify the length of the power cord or use an extension cord to power the unit.

• Do not share a single outlet with other electrical appliances. Improper power supply can cause ﬁ re or

electrical shock.

• Do not install you air conditioner in a wet room such as a bathroom or laundry room. Too much

exposure to water can cause electrical components to short circuit.

• Do not install the unit in a location that may be exposed to combustible gas as this could cause ﬁ re.

• The unit has wheels to facilitate moving. Make sure not to use the wheels on thick carpet or to roll over

objects as this could cause tipping.

• Do not operate a unit that been dropped or damaged.

• The appliance with the electric heater shall have at least 1 meter space from combustible materials.

• Do not touch the unit with wet or damp hands or when barefoot.

• If the air conditioner is knocked over during use, turn off the unit and unplug it from the main power

supply immediately. Visually inspect the unit to ensure there is no damage. If you suspect the unit has

been damaged contact a technician or customer service for assistance.

• In a thunderstorm, the power must be cut off to avoid damage to the machine due to lightning.

• You air conditioner should be used in such a way that it is protected from moisture. e.g. condensation,

splashed water, etc. Do not place or store you air conditioner where it can fall or be pulled into water

or any other liquid. Unplug immediately if this occurs.

• All wiring must be performed strictly in accordance with the wiring diagram location inside the unit.

• The units circuit board (PCB) is designed with a fuse to provide over current protection. The

speciﬁ cations of the fuse are printed on the circuit board.

• When the water drainage function is not in use keep the upper and lower drain plugs ﬁ rmly installed in

the unit. The drain plugs can be a choking hazard to children.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

CAUTION

• This appliance is not intended for use by persons (including children) whose physical, sensory or

mental capabilities may be different or reduced, or who lack experience or knowledge, unless such

persons receive supervision or training to operate the appliance by a person responsible for their

safety. Children should be supervised to ensure that they do not play with the appliance. Children must

be supervised around the unit at all times.

• If the power supply cord is damaged it must be replaced by the manufacturer, its service agent or

similarly qualiﬁ ed persons in order to avoid a hazard.

• Prior to cleaning or other maintenance, the appliance must be disconnected from the power supply.

• Do not remove any ﬁ xed covers. Never use this appliance if it is not working properly or if it has been

dropped or damaged.

• Do not run cord under carpeting. Do not cover cord with throw rugs, runners or similar coverings. Do

not route cord under furniture or appliances. Arrange cords away from trafﬁ c and where it will not be

tripped over.

• Do not operate a unit with a damaged power cord, plug, power fuse or circuit breaker. Discard the unit

or return to an authorized service facility for examination and/or repair.

• To reduce the risk of ﬁ re or electric shock do not use this air conditioner with any solid-state speed

control device.

• The appliance shall be installed in accordance with national wiring regulations.

• Contact the authorized service technician for repair or maintenance of this unit.

• Contact the authorized service installer for installation of this unit.

• Do not cover or obstruct the inlet or outlet grilles.

• Do not use this product for functions other than those described in this instruction manual.

• Before cleaning turn off the power and unplug the unit.

• Disconnect the power if strange sounds, smells or smoke comes from it.

• Do not press the buttons on the control panel with anything other than your ﬁ ngers.

• Do not remove any ﬁ xed covers. Never use this appliance if it is not working properly or if it has been

dropped or damaged.

• Do not operate or stop the unit by inserting or pulling out the power cord plug.

• Do not use hazardous chemicals to clean or come into contact with the unit. Do not use the unit in the

presence of inﬂ ammable substances or vapour such as alcohol, insecticides, petrol, etc.

• Always transport your air conditioner in a vertical position and stand on a stable, level surface during

use.

• Always contact a qualiﬁ ed person to carry out repairs. If the damaged power supply cord must be

replaced with a new power supply cord obtained from the product manufacturer and not repaired.

• Hold the plug by the head of the power plug when removing it.

• Turn off the appliance when not in use.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Note about ﬂ uorinated gasses

• Fluorinated greenhouse gases are contained in hermetically sealed equipment. For speciﬁ c information

on the type, the amount and the C02 equivalent in tonnes of the ﬂ uorinated greenhouse gas on some

models. Please refer to the relevant label on the unit itself.

• Installation, service, maintenance and repair of this unit must be performed by a certiﬁ ed technician.

• Product installation and recycling must be performed by a certiﬁ ed technician.

WARNING for using R32 refrigerant

• Do not use means to accelerate the defrosting process or to clean other than those recommended by the

manufacturer.

• The appliance shall be stored in a room without continuously operating ignition sources for example,

open ﬂ ames, an operating gas appliance or an operating electric heater.

• Do not pierce or burn.

• Be aware that the refrigerants may not contain an odour.

• The appliance should be installed, operated and stored in a room with a ﬂ oor area according to the

amount of refrigerant to be charged. For speciﬁ c information on the type of gas and the amount,

please refer to the relevant label on the unit itself. When there are differences between the label and the

manual on the minimum room area description, the description on the label shall prevail.

• Compliance with national gas regulations shall be observed.

• Keep ventilation openings clear of obstruction.

• The appliance shall be stored so as to prevent mechanical damage from occurring.

• A warning that the appliance shall be stored in a well-ventilated area where the room size corresponds

to the room area as speciﬁ ed for operation.

• Any person involved with working on the refrigerant circuit should hold a current, valid certiﬁ cate from

an industry accredited assessment authority which authorizes their competence to handle refrigerants

safely in accordance with an industry recognized assessment speciﬁ cation.

• Servicing shall only be performed as recommended by the manufacturer. Maintenance and repair

requiring the assistance of other skilled personnel shall be carried out under the supervision of the

person competent in the use of ﬂ ammable refrigerants.

• Please follow the instruction carefully to handle, install, clear and service the air conditioner to

avoid any damage or hazard. Flammable refrigerant R32 is used within this air conditioner. When

maintaining or disposing of the air conditioner the refrigerant must be recovered properly and should

not be allowed to discharge to the air directly.

• No open ﬁ re or device like switch which may generate spark/arcing shall be around air conditioner to

avoid causing ignition of the ﬂ ammable refrigerant used.

• Please follow the instruction carefully to store or maintain the air conditioner to prevent mechanical

damage from occurring.

• Flammable refrigerant -R32 is used in air conditioner. Please follow the instruction carefully to avoid

any hazard. For speciﬁ c information on the type of gas and the amount, please to the relevant label on

the unit itself.

• The appliance shall be stored in a room without continuously operating open ﬂ ames (for example an

operating gas appliance) and ignition sources (for example an operating electric heater).

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Transport of equipment containing ﬂ ammable refrigerants

See transport regulations.

Marking of equipment using signs

See local regulations.

Disposal of equipment using ﬂ ammable refrigerants

See national regulations.

Storage of equipment / appliances

The storage of equipment should be in accordance with the manufacturer’s instructions.

Storage of packed (unsold) equipment

Storage package protection should be constructed such that the mechanical damage to the equipment

inside the package will not cause a leak of the refrigerant charge. The maximum number of pieces of

equipment permitted to be stored together will be determined by local regulations.

Information on servicing

1. Checks to the area: Prior to beginning work on systems containing ﬂ ammable refrigerants, safety

checks are necessary to ensure that the risk of ignition is minimized. For repair to the refrigerating

system, the following precautions shall be complied with prior to conducting work on the system.

2. Work procedure: Work shall be undertaken under a controlled procedure so as to minimize the risk of

a ﬂ ammable gas or vapour being present while the work is being performed.

3. General work area: All maintenance staff and others working in the local area shall be instructed on

the nature of work being carried out. Work in conﬁ ned spaces shall be avoided. The area around the

work space shall be sectioned off. Ensure that the conditions within the work area have been made safe

by removing all ﬂ ammable material.

4. Checking for the presence of refrigerant: The area shall be checked with an appropriate refrigerant

detector prior to and during work to ensure the technician is aware of potentially ﬂ ammable

atmospheres. Ensure that the leak detection equipment being used is suitable for use with ﬂ ammable

refrigerants, i.e. non-sparking, adequately sealed and intrinsically safe.

5. Presence of ﬁ re extinguisher: If any hot work is to be conducted on the refrigeration equipment or

any associated parts, appropriate ﬁ re extinguishing equipment shall be available to hand. Have a dry

powder or C02 ﬁ re extinguisher adjacent to the work area.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

6. No ignition sources: No person carrying out work in relation to a refrigeration system which involves

exposing any pipe work that contains or has contained ﬂ ammable refrigerant shall use any sources

of ignition in such a manner that it may lead to risk of ﬁ re or explosion. All possible ignition sources

including cigarette smoking, should be kept sufﬁ ciently far away from the site of installation, repairing,

removing and disposal during which ﬂ ammable refrigerant can possibly be released to the surrounding

space. Prior to work taking place, the area around the equipment is to be surveyed to make sure there

are no ﬂ ammable hazards or ignition risks. No smoking signs shall be displayed.

7. Ventilated area: Ensure that the area is in the open or that it is adequately ventilated before breaking

into the system or conducting any hot work. A degree of ventilation shall continue during the period

that the work is carried out. The ventilation should safely disperse any released refrigerant and

preferable expel it externally into the atmosphere.

8. Checks to the refrigeration equipment: Where electrical components are being changed, they shall

be ﬁ t for the purpose and to the correct speciﬁ cation. At all times the manufacturer’s maintenance and

service guidelines shall be followed. If in doubt consult the manufacturer’s technical department for

assistance.

The following checks shall be applied to installations using ﬂ ammable refrigerants:

• The charge size is in accordance with the room size within which the refrigerant containing parts are

installed.

• The ventilation machinery and outlets are operating adequately and are not obstructed.

• If an indirect refrigerating circuit is being used, the secondary circuit shall be checked for the presence

of refrigerant.

• Marking to the equipment continues to be visible and legible. Markings and signs that become illegible

must be corrected.

• Refrigeration pipe or components are installed in a position where they are unlikely to be exposed

to any substance which may corrode refrigerant containing components, unless the components are

constructed of materials which are inherently resistant to being corroded or are suitable protected

against being corroded.

9. Checks to electrical devices: Repair and maintenance to electrical components shall include initial

safety checks and component inspection procedures. If a fault exists that could compromise safety, then

no electrical supply shall be connected to the circuit until it is satisfactorily dealt with. If the fault cannot

be corrected immediately but it is necessary to continue operation, an adequate temporary solution

shall be used. This shall be reported to the owner of the equipment so all parties are advised.

Initial safety checks shall include:

• That capacitors are discharged. This shall be done in a safe manner to avoid possibility of sparking.

• That no live electrical components and wiring are exposed while charging, recovering or purging the

system.

• That there is continuity of earth bonding.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Repairs to sealed components

1. During repairs to sealed components, all electrical supplies shall be disconnected from the equipment

being worked upon prior to any removal of sealed covers, etc. If it is absolutely necessary to have an

electrical supply to equipment during servicing then a permanently operating form of leak detection

shall be located at the most critical point to warn of a potentially hazardous situation.

2. To ensure that by working on electrical components the casing is not altered in such a way that the level

of protection is affected, particular attention shall be paid to the following:

• Damage to cables, excessive number of connections, terminals not made to original speciﬁ cation,

damage to seals, incorrect ﬁ tting of glands, etc.

• Ensure the apparatus is mounted securely.

• Ensure that seals or sealing materials have not degraded such that they no longer serve the purpose of

preventing the ingress of ﬂ ammable atmospheres. Replacement parts shall be in accordance with the

manufacturer’s speciﬁ cations.

Note: The use of silicon sealant may inhibit the effectiveness of some types of leak detection equipment.

Intrinsically safe components do not have to be isolated prior to working on them.

Repair to intrinsically safe components

Do not apply any permanent inductive or capacitance loads to the circuit without ensuring that this

will not exceed the permissible voltage and current permitted for the equipment in use. Intrinsically

safe components are the only types that can be worked on while live in the presence of a ﬂ ammable

atmosphere. The test apparatus shall be at the correct rating. Replace components only with parts speciﬁ ed

by the manufacturer. Other parts may result in the ignition of refrigerant in the atmosphere from a leak.

Cabling

Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp edges or any

other adverse environmental effects. The check shall also take into account the effects of aging or continual

vibration from sources such as compressors or fans.

Detection of ﬂ ammable refrigerants

Under no circumstances shall potential sources of ignition be used in the searching for or detection of

refrigerant leaks. A halide torch or any other detector using a naked ﬂ ame shall not be used.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Leak detection methods

The following leak detection methods are deemed acceptable for systems containing ﬂ ammable

refrigerants:

• Electronic leak detectors shall be used to detect ﬂ ammable refrigerants but the sensitivity may not be

adequate or may need recalibration. Detection equipment shall be calibrated in a refrigerant-free area.

Ensure that the detector is not a potential source of ignition and is suitable for the refrigerant used.

• Leak detection equipment shall be set at a percentage of the LFL of the refrigerant and shall be

calibrated to the refrigerant employed and the appropriate percentage of gas (25% maximum) is

conﬁ rmed.

• Leak detection ﬂ uids are suitable for use with most refrigerants but the use of detergents containing

chlorine shall be avoided as the chlorine may react with the refrigerant and corrode the copper or

pipe-work.

• If a leak is suspected, all naked ﬂ ames shall be removed or extinguished.

• If a leakage of refrigerant is found which requires brazing, all of the refrigerant shall be recovered

from the system or isolated by means of shut off valves in a part of the system remote from the leak.

Oxygen free nitrogen (OFN) shall then be purged through the system both before and during the

brazing process.

Removal and evacuation

When breaking into the refrigerant circuit to make repairs or for any other purpose conventional

procedures shall be used. However, it is important that the best practice is followed since ﬂ ammability is a

consideration. The following procedures shall be adhered to:

• Remove refrigerant.

• Purge the circuit with inert gas.

• Evacuate.

• Purge again with inert gas.

• Open the circuit by cutting or brazing.

• The refrigerant charge shall be recovered into the correct recovery cylinders. The system shall be

ﬂ ushed with OFN to render the unit safe. This process may need to be repeated several times.

Compressed air or oxygen shall not be used for this task.

• Flushing shall be achieved by breaking the vacuum in the system with OFN and continuing to ﬁ ll until

the working pressure is achieved, then venting to atmosphere and ﬁ nally pulling down to a vacuum.

This process shall be repeated until no refrigerant is within the system. When the ﬁ nal OFN charge

is used, the system shall be vented down to atmospheric pressure to enable work to take place. This

operation is absolutely vital is brazing operations on the pipe-work are to take place.

• Ensure that the outlet for the vacuum pump is not close to any ignition sources and there is ventilation

available.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Charging procedures

In addition to conventional charging procedures, the following requirements shall be followed:

• Ensure that contamination of different refrigerants does not occur when using charging equipment.

Hoses or lines shall be as short as possible to minimize the amount of refrigerant contained in them.

• Cylinders shall be kept upright.

• Ensure that the refrigeration system is earthed prior to charging the system with refrigerant.

• Label the system when charging is complete, if not already labeled.

• Extreme care shall be taken not to overﬁ ll the refrigeration system.

• Prior to recharging the system it shall be pressure tested with OFN. The system shall be leak tested on

completion of charging but prior to commissioning. A follow up leak test shall be carried out prior to

leaving the site.

Decommissioning

Before carrying out this procedure, it is essential that the technician is completely familiar with the

equipment in all its detail. It is recommended good practice that all refrigerants are recovered safely. Prior

to the task being carried out, an oil and refrigerant sample shall be taken in case analysis is required

prior to re-use of reclaimed refrigerant. It is essential that electrical power is available before the task is

commenced.

A. Become familiar with the equipment and its operation.

B. Isolate system electrically.

C. Before attempting the procedure ensure that:

• Mechanical handling equipment is available if required for handling refrigerant cylinders.

• All personal protective equipment is available and being used correctly.

• The recovery process is supervised at all times by a competent person.

• Recovery equipment and cylinders conform to the appropriate standards.

D. Pump down refrigerant system, if possible.

E. If a vacuum is not possible, make a manifold so that refrigerant can be removed from various parts of

the system.

F. Make sure that cylinder is situated on the scales before recovery takes place.

G. Start the recovery machine and operate in accordance with the manufacturer’s instructions.

H. Do not overﬁ ll cylinders. No more than 80% volume liquid charge.

I. Do not exceed the maximum working pressure of the cylinder, even temporarily.

J. When the cylinders have been ﬁ lled correctly and the process is completed, make sure that the cylinders

and the equipment are removed from the site promptly and all isolation valves on the equipment are

closed off.

K. Recovered refrigerant shall not be charged into another refrigeration system unless it has been cleaned

and checked.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS!

Labeling

Equipment shall be labeled stating that it has been decommissioned and emptied of refrigerant. The label

shall be dated and signed. Ensure that there are labels on the equipment stating the equipment contains

ﬂ ammable refrigerant.

Recovery

When removing refrigerant from a system, either for servicing or decommissioning, it is recommended

good practice that all refrigerants are removed safely.

When transferring refrigerant into cylinders, ensure that only appropriate refrigerant recovers cylinders are

employed. Ensure that the correct number of cylinders for holding the total system charge are available.

All cylinders to be used are designed for the recovered refrigerant and labeled for that refrigerant, i.e.

special cylinders for the recovery of refrigerant. Cylinders shall be complete with pressure relief valve and

associated shut-off valves in good working order. Empty recovery cylinders are evacuated and, if possible,

cooled before recovery occurs.

The recovery equipment shall be in good working order with a set of instructions concerning the equipment

that is at hand and shall be suitable for the recovery of ﬂ ammable refrigerants. In addition, a set of

calibrated weighing scales shall be available and in good working order. Hoses shall be complete with

leak-free disconnect couplings and in good condition. Before using the recovery machine, check that is it

in satisfactory working order, has been properly maintained and that any associated electrical components

are sealed to prevent ignition in the event of a refrigerant leak. Consult the manufacturer if in doubt.

The recovered refrigerant shall be returned to the refrigerant supplier in the correct recovery cylinder

and the relevant waste transfer note shall be arranged. Do not mix refrigerants in recovery units and

especially not in cylinders. If compressors or compressor oils are to be removed, ensure that they have

been evacuated to an acceptable level to make certain that ﬂ ammable refrigerant does not remain within

the lubricant. The evacuation process shall be carried out prior to returning the compressor to the suppliers.

Only electric heating to the compressor body shall be employed to accelerate this process. When oil is

drained form a system, it shall be carried out safely.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

INSTALLATION INSTRUCTIONS

12

ACCESSORIES

1. Air outlet adapter

2. Exhaust hose

3. Window slider adapter

4. 2 Bolts

5. Window slider A

6. Window slider B and C

7. Foam seal A (adhesive)

8. Foam seal B (adhesive)

9. Foam seal C (non-adhesive)

10. Security bracket and 2 screws

11. Drain hose

12. Power cord storage band

13. Remote control and batteries

REQUIRED TOOLS

1. Medium sized Phillips screwdriver

2. Tape measure or ruler

3. Knife or scissors

4. Saw (in the event that the window sliders need to

be cut to size)

ON/OFF

TEMP

S

H

C

O

U

R

T

I

O

M

N

ER

T

I

O

M

F

E

F

R

MOD E

FAN

LED

SLEEP SWING

1

2

3

4

5

6

7

8

9

10

11

12

13

FM

ION

IMPORTANT WARNING

Do not leave this appliance unattended

in a space where people or animals who

cannot react to a malfunction are located. A

malfunction such as the exhaust hose becoming

dislocated, can cause extreme overheating or

death in an enclosed, unattended space.

INSTALLATION INSTRUCTIONS

13

INSTALLING THE WINDOW KIT

The instructions below can be used for either a hung window or a

sliding window application.

1. Measure the window opening where the window kit will be

installed. Assemble as many sliders as necessary to ﬁ t the

window. If the window opening is less than the minimum length

of a single slider, use the slider that has the hole in it and cut it

to the correct length. Make sure not to cut the end that has the

hole as this is necessary to attach the exhaust hose adapter. Cut

the adhesive foam seals to the correct length for the window

and attach them to the window sash and frame.

2. Connect the window slider adapter to the window slider by

gently pressing it into the hole in the slider until it clicks into

place.

3. Attach the exhaust hose to the window slider adapter by gently

pressing it into the adapter until it clicks into place.

4. Install the slider kit and hose assembly and close the window to

hold it in place.

5. Attach the air outlet adapter to the back of the appliance by

sliding it down into the channel around the air outlet. Attach the

hose to the air outlet adapter on the back of the appliance by

gently pressing it into the adapter until it clicks into place.

6. Cut the non-adhesive foam seal to match the width of the

window and insert it between the glass and the window frame

to prevent air and insects from getting into the room.

7. Install the security bracket in the window frame with the

provided screws.

Note: Do not over extend or bend the hose as this will impede air

ﬂ ow.

A

B

AB

1

2

3

4

5

6

7

OPERATING INSTRUCTIONS

14

FEATURES

Front

1. Control panel

2. Louver

3. Handle (both sides)

4. Casters

Rear

1. Upper air ﬁ lter and air intake

2. Continuous drain outlet

3. Lower air ﬁ lter and air intake

4. Air outlet

5. Power cord storage band

6. Power cord

7. Overﬂ ow tray drain outlet

1

2

3

4

LOCATION

Place the air conditioner on a smooth, level ﬂ oor

that is strong enough to support it and all included

accessories.

Make sure the appliance is level to minimize noise

and vibration.

The appliance must be installed near a grounded

receptacle and the overﬂ ow drain outlet on the rear

of the appliance must be accessible.

Do not cover air inlets or outlets or the remote

control receiver on the control panel.

The appliance requires 30 cm (12 inches) of

clearance on the front and sides and the horizontal

louver blade should be 50 cm (20 inches) away

from obstacles.

The appliance requires at least 50 cm (20 inches) of

clearance on the back.

1

7

2

3

5

4

6

15

CONTROL PANEL

1. Swing button: Press to start the auto swing

feature. When auto swing is activated, press

again to stop the louver at the desired angle.

2. Timer button: Press to start the automatic timer.

Light will indicate whether a timer is set.

3. Mode button: Press to select the desired mode.

Modes will cycle in sequence with each press

of the button; auto, cool, dry, fan. Light will

indicate current mode.

4. Temperature control buttons:

• Used to set the temperature.

• Press and hold both temperature control buttons

for three seconds to change the temperature

display from °C to °F.

5. LED display:

• Shows the set temperature in °C or °F.

• Shows the timer settings.

• While on dry or fan mode, shows the room

temperature.

6. Fan button:

• Press to select fan speed; low, medium or high.

Light will indicate current speed.

• Press and hold for 3 seconds to turn the

continuous fan on or off.

7. Sleep button: Press to start the sleep feature.

8. Power button: Press to turn the appliance on or

off.

OPERATING INSTRUCTIONS

123

4

5

678

3sec

OPERATING MODES

Cool Mode

Choose cool mode to set the cooling function.

• Use the temperature control buttons to choose the

desired temperature.

• Use the fan button to choose the desired fan speed.

• The temperature can be set within a range of 17 -

30°C (62 - 86°F).

• The exhaust hose should be installed during cool

mode to ensure the best results.

Dry Mode

Choose dry mode to remove excess moisture from

the air. Water will condense inside the appliance and

drain out the back.

• The humidity level and fan speed will be

automatically set and cannot be modiﬁ ed in dry

mode.

• The exhaust hose does not need to be installed

during dry mode.

• It may be necessary to install the continuous drain

hose during dry mode to remove excess water.

Fan Mode

Fan mode can be used to run the fan without

engaging the cooling or dehumidifying functions.

• Press the fan button to choose the desired fan

speed.

• The exhaust hose does not need to be installed

during fan mode.

• In cooling or dry mode, press and hold the

fan button for 3 seconds to set the fan to run

continuously. Press and hold the fan button for 3

seconds to disengage the continuous fan. During

normal operation the fan will turn on and off with

the compressor.

Auto Mode

Auto mode is a pre-set factory program that

automatically deﬁ nes the mode (cool or fan) and fan

speed based on the set temperature and the ambient

temperature. The exhaust hose should be installed

during auto mode.

OPERATING INSTRUCTIONS

16

REMOTE CONTROL

1. Power button: Press to turn the appliance on or

off.

2. Mode button: Press to select the desired mode.

3. Fan button: Press to select fan speed.

4. Sleep button: Press to start the sleep feature.

5. Swing button: Press to start the auto swing

feature. When auto swing is activated, press

again to stop the louver at the desired angle.

6. Follow me button: Press to activate the follow

me feature.

7. LED button: Press to turn the LED display on or

off.

8. Timer off button: Press to set the automatic off

timer.

9. Timer on button: Press to set the automatic on

timer.

10. Shor tcut button: Press to set and activate the

short cut function.

11. Temperature control buttons:

• Used to set the temperature.

• Press and hold both temperature control buttons

for 3 seconds to change the temperature display

from °C to °F.

12. LED display:

• Shows the set temperature in °C or °F or the

auto-timer settings.

1

2

3

4 5 6 7

8

9

10

11

12

SHORTCUT FUNCTION

The shortcut function can be used to save a favourite

setting. The shortcut function is only available on the

remote control.

To set a favourite, set the appliance to the desired

temperature and fan speed. Press and hold the

shortcut button for 2 seconds. Press the shortcut

button at any point in future to return to the

favourite setting.

If no favourite is set, pressing the shortcut button will

cause the appliance to run in auto mode at 29°C

(79°F), with fan speed set to auto.

OPERATING INSTRUCTIONS

17

REPLACING THE REMOTE BATTERIES

This air conditioner comes with two AAA batteries. Place the batteries in the remote control before use.

1. Slide the back cover from the remote downward to expose the battery compartment.

2. Insert the batteries, ensure to match the (+) and (-) symbols on the ends of the batteries with the symbols

inside the battery compartment.

3. Slide the battery cover back into place.

Notes:

• The air conditioner will not respond if curtains, doors or other materials block the signal from the

remote control to the unit.

• Prevent any liquid from contact with the remote control. Do not expose the remote control to direct

sunlight or heat.

• If the infrared signal receiver on the indoor unit is exposed to direct sunlight, the air conditioner may

not function properly. Use curtains to prevent the sunlight from falling on the receiver.

• Do not mix old and new batteries or batteries of different types.

• Do not leave the batteries in the remote control if it is not going to be used for more than 2 months.

IMPORTANT

Do not dispose of batteries as unsorted municipal

waste. Refer to local laws for proper disposal of

batteries.

OPERATING INSTRUCTIONS

18

REMOTE CONTROL REGULATIONS

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

1. Reorient or relocate the receiving antenna

2. Increase the separation between the equipment and receiver

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

4. Consult the dealer or an experienced radio/TV technician for help

Changes or modiﬁ cations not approved by the party responsible for FCC and Industry Canada compliance

could void the user’s authority to operate the equipment. This appliance complies with Part 15 of the FCC

Rules and license-exempt RSS standards.

Operation is subject to the following conditions:

1. This device may not cause interference.

2. This device must accept any interference received, including interference that may cause undesired

operation.

This equipment complies with FCC RF and IC RSS-102 radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm

(8 inches) between the radiator and your body.

This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this

device does not cause harmful interference. This device complies with Canadian CAN ICES-003(B)/NMB-

003(B)

This device contains:

FCC ID: 2ADQOMDNA21

IC: 12575A-MDNA21

SUPPLIER’S DECLARATION OF CONFORMITY

Unique Identiﬁ er: Midea, RG57H4(B)/BGCEF

Responsible Party U.S. Contact Information:

Midea America Corporation

300 Kimball Dr

Parsippany, NJ

07054

Telephone number or internet contact information: Midea.com/US

19

OPERATING INSTRUCTIONS

TIMER

Auto Off

1. When the air conditioner is turned on, press the

timer button to activate the auto off timer.

2. Press the temperature control buttons to change

the set time in 0.5 hour increments up to 10

hours and then in 1 hour increments up to 24

hours.

Auto On

1. When the air conditioner is turned off, press the

timer button to activate the auto on timer.

2. Press the temperature control buttons to change

the set time in 0.5 hour increments up to 10

hours and then in 1 hour increments up to 24

hours.

Using Auto On and Auto Off Together

The auto on and auto off timers can be used at the

same time by ﬁ rst setting one and then the other.

For example, if the air conditioner is running,

you can set the auto off timer to let it run for a set

amount of time before turning off and then set the

auto on timer to turn it back on at a later time.

Or, if the air conditioner is not running, you can set

the auto on timer to turn it on at a later time and

then set the auto off timer to shut it off after running

for a period of time.

Note: The timer will not cycle the air conditioner on

and off indeﬁ nitely. The auto on and auto off timers

will function one time and then the air conditioner

will return to regular functioning.

Turning the air conditioner on or off at any time

or changing the timer setting to 0.0 will cancel the

timer settings.

FOLLOW ME FUNCTION

There is a temperature sensor built into the remote

control that will continuously collect the current

room temperature. Keep the remote control with

you and the appliance will automatically adjust the

set temperature based on the current temperature

where you are located to reach the most

comfortable condition and temperature.

Press the follow me button to activate the follow

me function. The remote will display the current

temperature at its location. The remote will send

a signal to the air conditioner every 3 minutes, so

long as you remain within range of the appliance.

The follow me light on the control panel of the

appliance will illuminate for 5 seconds every three

minutes to indicate that it has received a signal

from the remote. If the appliance does not receive a

signal from the remote during any 7 minute interval,

it will beep to indicate that the follow me mode has

ended.

The maximum distance for the follow me feature is

8 meters (26 feet). This feature is available in cool

and auto modes.

SLEEP FUNCTION

The sleep function can be used to conserve energy

during sleeping hours.

When selected, the set temperature will increase

by 1°C/2°F every half hour for one full hour. The

appliance will hold the new set temperature for

6 hours before automatically returning to normal

operation.

The sleep function can be canceled at any time by

pressing the sleep button.

La page charge ...

Danby DPA060B1WDB Le manuel du propriétaire

Danby DPA060B1WDB Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents