Modern Forms PD-64803R Chaos Mode d'emploi

Modern Forms
Marque
Modern Forms
Modèle
PD-64803R Chaos
Taper
Mode d'emploi
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 1
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64803R
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER
BEFORE BEGINNING.
‐ Read all instructions before installing.
‐ System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local
regulations.
‐ When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
‐ Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts
and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product
by Modern Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the
manufacturer if any parts are damaged or missing.
MAINTENANCENOTE:Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in
coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
‐ Lisez toutes les instructions avant l’installation.
‐ Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également
aux règlements locaux.
‐ Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé
seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou
accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également
causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont
endommagées.
NOTED’ENTRETIEN:Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous
recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes
les deux semaines avec un chiffon humide.
HARDWARE
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 2
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64803R
PREPARATION Fig.1
1. Shut off the power at the circuit breaker and remove
existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the
parts on a clear area. Be careful not to lose any small
parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) from the fixture.
4. Install the mounting back plate to the junction box using
5. Mark the three wood screw mounting holes on the ceiling,
remove mounting back plate, drill holes and insert the three
plastic anchors (D). The side of the mounting plate marked
“GND” must face out.
6. Adjust the fixture wire length by pushing the cable gripper on
the canopy and pulling the wires as desired. Make sure the
wires length like (Fig. 4). Retract these wires close to a
desirable length to within the canopy before securing
the fixture in place.
Note: retracting or extending excessive cable length through
the cable gripper is not recommended.
Warning: Shortening these cables without professional helps
or electronic background is not advisable. Any modifications to
the fixture may result in voiding the warranty of the product.
CONNECTING THE WIRES (Fig.2)
7. Connect the driver’s input wires to junction box wires, connect the
drivre’s output wire to fixture wire, making sure that all wire
connectors (A) are secured. If your outlet box has a green or
bare copper ground wire, connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to the back plate
using the green screw provided. After wires are connected, tuck them
carefully inside the junction box.
8. Secure the fixture to the mounting back plate using the mounting screw (B)
DIMMING WIRING INFORMATION (Fig. 3)
9. This fixture features electronic low voltage (ELV or TRAIC) or 0-10V
dimming capabilities. See notes below for specific dimming wires information.
10. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral)
and bare copper ground wire (ground).
11. To utilize 0-10V dimming: use wire purple (dim+), gray (dim-), black (hot),
white (neutral) and bare copper ground wire (ground).
NOTE: Make sure to connect 0-10V prior to power-up the fixture in order to allow
the 0-10V dimming to function properly.
Fig. 2 Wiring Fig. 3 Driver Wires
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 3
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64803R
Fig. 4 Wires length
Wire diagram
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 1
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64805R
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER
BEFORE BEGINNING.
‐ Read all instructions before installing.
‐ System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local
regulations.
‐ When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
‐ Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts
and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product
by Modern Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the
manufacturer if any parts are damaged or missing.
MAINTENANCENOTE:Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in
coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
‐ Lisez toutes les instructions avant l’installation.
‐ Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également
aux règlements locaux.
‐ Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé
seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou
accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également
causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont
endommagées.
NOTED’ENTRETIEN:Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous
recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes
les deux semaines avec un chiffon humide.
HARDWARE
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 2
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64805R
PREPARATION Fig.1
1. Shut off the power at the circuit breaker and remove
existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the
parts on a clear area. Be careful not to lose any small
parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) from the fixture.
4. Install the mounting back plate to the junction box using
5. Mark the three wood screw mounting holes on the ceiling,
remove mounting back plate, drill holes and insert the three
plastic anchors (D). The side of the mounting plate
marked “GND” must face out.
6. Adjust the fixture wire length by pushing the cable gripper on
the canopy and pulling the wires as desired. Make sure the
wires length like (Fig. 4). Retract these wires close to a
desirable length to within the canopy before securing
the fixture in place.
Note: retracting or extending excessive cable length through
the cable gripper is not recommended.
Warning: Shortening these cables without professional helps
or electronic background is not advisable. Any modifications to
the fixture may result in voiding the warranty of the product.
CONNECTING THE WIRES (Fig.2)
7. Connect the driver’s input wires to junction box wires, connect the
drivre’s output wire to fixture wire, making sure that all wire
connectors (A) are secured. If your outlet box has a green or
bare copper ground wire, connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to the back plate
using the green screw provided. After wires are connected, tuck them
carefully inside the junction box.
8. Secure the fixture to the mounting back plate using the mounting screw (B)
DIMMING WIRING INFORMATION (Fig. 3)
9. This fixture features electronic low voltage (ELV or TRAIC) or 0-10V
dimming capabilities. See notes below for specific dimming wires information.
10. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral)
and bare copper ground wire (ground).
11. To utilize 0-10V dimming: use wire purple (dim+), gray (dim-), black (hot),
white (neutral) and bare copper ground wire (ground).
NOTE: Make sure to connect 0-10V prior to power-up the fixture in order to allow
the 0-10V dimming to function properly.
Fig. 2 Wiring Fig. 3 Driver Wires
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 3
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64805R
Fig. 4 Wires length
Wire diagram
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 1
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64809R
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER
BEFORE BEGINNING.
‐ Read all instructions before installing.
‐ System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local
regulations.
‐ When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
‐ Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts
and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product
by Modern Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the
manufacturer if any parts are damaged or missing.
MAINTENANCENOTE:Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in
coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
‐ Lisez toutes les instructions avant l’installation.
‐ Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également
aux règlements locaux.
‐ Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé
seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou
accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également
causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont
endommagées.
NOTED’ENTRETIEN:Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous
recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes
les deux semaines avec un chiffon humide.
HARDWARE
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 2
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64809R
PREPARATION Fig.1
1. Shut off the power at the circuit breaker and remove
existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the
parts on a clear area. Be careful not to lose any small
parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) from the fixture.
4. Install the mounting back plate to the junction box using
5. Mark the three wood screw mounting holes on the ceiling,
remove mounting back plate, drill holes and insert the three
plastic anchors (D). The side of the mounting plate marked
“GND” must face out.
6. Adjust the fixture wire length by pushing the cable gripper on
the canopy and pulling the wires as desired. Make sure the
wires length like (Fig. 4). Retract these wires close to a
desirable length to within the canopy before securing
the fixture in place.
Note: retracting or extending excessive cable length through
the cable gripper is not recommended.
Warning: Shortening these cables without professional helps
or electronic background is not advisable. Any modifications to
the fixture may result in voiding the warranty of the product.
CONNECTING THE WIRES (Fig.2)
7. Connect the driver’s input wires to junction box wires, connect the
drivre’s output wire to fixture wire, making sure that all wire
connectors (A) are secured. If your outlet box has a green or
bare copper ground wire, connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to the back plate
using the green screw provided. After wires are connected, tuck them
carefully inside the junction box.
8. Secure the fixture to the mounting back plate using the mounting screw (B)
DIMMING WIRING INFORMATION (Fig. 3)
9. This fixture features electronic low voltage (ELV or TRAIC) or 0-10V
dimming capabilities. See notes below for specific dimming wires information.
10. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral)
and bare copper ground wire (ground).
11. To utilize 0-10V dimming: use wire purple (dim+), gray (dim-), black (hot),
white (neutral) and bare copper ground wire (ground).
NOTE: Make sure to connect 0-10V prior to power-up the fixture in order to allow
the 0-10V dimming to function properly.
Fig. 2 Wiring Fig. 3 Driver Wires
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 3
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64809R
Fig. 4 Wires length
Wire diagram
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 1
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64815R
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER
BEFORE BEGINNING.
‐ Read all instructions before installing.
‐ System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local
regulations.
‐ When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
‐ Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts
and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product
by Modern Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the
manufacturer if any parts are damaged or missing.
MAINTENANCENOTE:Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in
coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
‐ Lisez toutes les instructions avant l’installation.
‐ Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également
aux règlements locaux.
‐ Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé
seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou
accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également
causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont
endommagées.
NOTED’ENTRETIEN:Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous
recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes
les deux semaines avec un chiffon humide.
HARDWARE
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 2
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64815R
PREPARATION Fig.1
1. Shut off the power at the circuit breaker and remove
existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the
parts on a clear area. Be careful not to lose any small
parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) from the fixture.
4. Install the mounting back plate to the junction box using
5. Mark the three wood screw mounting holes on the ceiling,
remove mounting back plate, drill holes and insert the three
plastic anchors (D). The side of the mounting plate marked
“GND” must face out.
6. Adjust the fixture wire length by pushing the cable gripper on
the canopy and pulling the wires as desired. Make sure the
wires length like (Fig. 4). Retract these wires close to a
desirable length to within the canopy before securing
the fixture in place.
Note: retracting or extending excessive cable length through
the cable gripper is not recommended.
Warning: Shortening these cables without professional helps
or electronic background is not advisable. Any modifications to
the fixture may result in voiding the warranty of the product.
CONNECTING THE WIRES (Fig.2)
7. Connect the driver’s input wires to junction box wires, connect the
drivre’s output wire to fixture wire, making sure that all wire
connectors (A) are secured. If your outlet box has a green or
bare copper ground wire, connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to the back plate
using the green screw provided. After wires are connected, tuck them
carefully inside the junction box.
8. Hook the two safety cords to the mounting plate.
9. Push the fixture onto the mounting back plate AND rotate
the fixture until it is docked in position, and secure it with
mounting screws (B).
DIMMING WIRING INFORMATION (Fig. 3)
10. This fixture features electronic low voltage (ELV or TRAIC) or 0-10V
dimming capabilities. See notes below for specific dimming wires information.
11. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral)
and bare copper ground wire (ground).
12. To utilize 0-10V dimming: use wire purple (dim+), gray (dim-), black (hot),
white (neutral) and bare copper ground wire (ground).
NOTE: Make sure to connect 0-10V prior to power-up the fixture in order to allow
the 0-10V dimming to function properly.
Fig. 2 Wiring Fig. 3 Driver Wires
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 3
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64815R
Fig. 4 Wires length
Wire diagram
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 1
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64821R
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER
BEFORE BEGINNING.
‐ Read all instructions before installing.
‐ System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local
regulations.
‐ When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
‐ Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts
and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product
by Modern Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the
manufacturer if any parts are damaged or missing.
MAINTENANCENOTE:Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in
coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
‐ Lisez toutes les instructions avant l’installation.
‐ Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également
aux règlements locaux.
‐ Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé
seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou
accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également
causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont
endommagées.
NOTED’ENTRETIEN:Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous
recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes
les deux semaines avec un chiffon humide.
HARDWARE
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 2
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64821R
PREPARATION Fig.1
1. Shut off the power at the circuit breaker and remove
existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the
parts on a clear area. Be careful not to lose any small
parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) from the fixture.
4. Install the mounting back plate to the junction box using
5. Mark the three wood screw mounting holes on the ceiling,
remove mounting back plate, drill holes and insert the six
plastic anchors (D). The side of the mounting plate marked
“GND” must face out.
6. Adjust the fixture wire length by pushing the cable gripper on
the canopy and pulling the wires as desired. Make sure the
wires length like (Fig. 4). Retract these wires close to a
desirable length to within the canopy before securing
the fixture in place.
Note: retracting or extending excessive cable length through
the cable gripper is not recommended.
Warning: Shortening these cables without professional helps
or electronic background is not advisable. Any modifications to
the fixture may result in voiding the warranty of the product.
CONNECTING THE WIRES (Fig.2)
7. Connect the driver’s input wires to junction box wires, connect the
drivre’s output wire to fixture wire, making sure that all wire
connectors (A) are secured. If your outlet box has a green or
bare copper ground wire, connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to the back plate
using the green screw provided. After wires are connected, tuck them
carefully inside the junction box.
8. Hook the two safety cords to the mounting plate.
9. Push the fixture onto the mounting back plate AND rotate
the fixture until it is docked in position, and secure it with
mounting screws (B).
DIMMING WIRING INFORMATION (Fig. 3)
10. This fixture features electronic low voltage (ELV or TRAIC) or 0-10V
dimming capabilities. See notes below for specific dimming wires information.
11. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral)
and bare copper ground wire (ground).
12. To utilize 0-10V dimming: use wire purple (dim+), gray (dim-), black (hot),
white (neutral) and bare copper ground wire (ground).
NOTE: Make sure to connect 0-10V prior to power-up the fixture in order to allow
the 0-10V dimming to function properly.
Fig. 2 Wiring Fig. 3 Driver Wires
Modernforms.com
Phone (866) 810.6615
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2019 3
INSTALLATION INSTRUCTION
648-LED Pendant
PD-64821R
Fig. 4 Wires length
Wire diagram
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Modern Forms PD-64803R Chaos Mode d'emploi

Modern Forms
Marque
Modern Forms
Modèle
PD-64803R Chaos
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents