VTech VM5463-2 Mode d'emploi

Marque: VTech

Modèle: VM5463-2

Catégorie: Moniteurs vidéo bébé

Taper: Mode d'emploi

Ce manuel convient également à

VM5463

NOTESNOTE

• The rechargeable battery in the parent unit is built-in.

• Use only the power adapters supplied with this product.

• Make sure the baby monitor is not connected to a switch-controlled electric outlet.

• Connect the power adapters in a vertical or ﬂoor mount position only. The adapters’ prongs are not

designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table,

or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.

• Make sure the parent unit, the baby units and the power adapter cords are out of reach of children.

Press and hold

Speciﬁcations are subject to change without notice.

06/21. VM5463-X_QSG_V6.

Quick start guide

VM5463

VM5463-2

Full Color Pan and Tilt

Video Monitor

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

the latest VTech product news.

1 Connect the baby monitor

Power on or off the baby monitor

Slide the switch to power on or off your baby unit.

Press and hold POWER to power on or off your parent unit.

What’s in the box

Status check

Once you power on both your

baby unit and parent unit, your

parent unit displays image from

the baby unit, and the LINK LED

light turns on.

The ON LED light of baby unit

turns on.

3 Positioning the baby monitor

Caution

• The default volume of your parent unit

is level 4, and the maximum volume is

level 7. If you experience high-pitched

screeching noise from your baby

monitor while positioning:

- Make sure your baby unit and parent

unit are more than 3 feet (1 meter)

apart, OR

- Lower the volume of your parent unit.

NOTESNOTE

Note

• To avoid interference from other electronic

devices, place your baby monitor at least 3 feet

(1 meter) away from devices such as wireless

routers, microwaves, cell phones and computers.

Strangulation

Hazard

Keep this cord out of reach of children.

The cord needs to be at least three feet

away from the child at all times. Do not

use with an extension cord. Do not

remove this tag.

Éloignez ce cordon des enfants. Le

cordon doit se trouver à au moins trois

pieds d’un enfant et ce, en tout temps.

N’utilisez pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga este cable fuera de la alcance

de los niños. Este cable debe estar por

lo menos tres pies fuera de la alcance

del niño en todo momento. No lo use

con una extensión inalámbrica. No quite

esta etiqueta.

Risque

d’étranglement

Riesgo de

estrangulación

Strangulation

Hazard

Keep this cord out of reach of children.

The cord needs to be at least three feet

away from the child at all times. Do not

use with an extension cord. Do not

remove this tag.

Éloignez ce cordon des enfants. Le

cordon doit se trouver à au moins trois

pieds d’un enfant et ce, en tout temps.

N’utilisez pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga este cable fuera de la alcance

de los niños. Este cable debe estar por

lo menos tres pies fuera de la alcance

del niño en todo momento. No lo use

con una extensión inalámbrica. No quite

esta etiqueta.

Risque

d’étranglement

Riesgo de

estrangulación

Quick start guide

Adjust speaker volume

Press / to adjust your parent

unit speaker volume.

Zoom

Press to zoom in or out.

Talk to your baby unit

Press and hold TALK and speak to your

parent unit. Your voice is transmitted to

the baby unit. Release TALK when ﬁnish

talking and hear your baby again.

Use the menu

Press to enter the menu, choose a menu item,

or save a setting. You can use the parent unit for

advanced settings or operations, such as to play

or stop the baby unit lullaby, or to adjust the baby

unit sound sensitivity.

While in the menu:

• Press or to scroll among the menu options.

• Press to select an item, or to save a setting.

• Press or to scroll among the sub-menus,

or to adjust a setting.

• Press to return to the previous menu options

without changing the current setting.

• Press /EXIT to return to live video.

Basic operation - Parent unit

Turn off the screen

Press and hold LCD ON/OFF to switch off

the screen. You can still hear sound from

the baby unit.

Tip

• Press any key on the parent unit to turn on

the screen again.

Overview - Parent unit

Overview - Baby unit

Technical speciﬁcations

The applied nameplate is located at the bottom of the baby

unit’s base.

When using your equipment, basic safety precautions

should always be followed to reduce the risk of ﬁre, electric

shock and injury, including the following:

1. Follow all warnings and instructions marked on the

product.

2. Adult setup is required.

3. CAUTION: Do not install the baby unit at a height above

2 meters.

4. This product is not a substitute for adult supervision of the

infant. Supervising the infant is the parent’s or caregiver’s

responsibility. This product could cease operating, and

therefore you should not assume it will continue working

properly for any given period of time. Further, this is not a

medical device and should not be used as such. This product

is intended to assist you in supervising your baby.

5. Do not use this product near water. For example, do not

use it next to a bath tub, wash bowl, kitchen sink, laundry

tub or swimming pool, or in a wet basement or shower.

6. CAUTION: Use only the battery provided. There may be a risk

of explosion if a wrong type of battery is used for the parent

unit. The battery cannot be subjected to high or low extreme

temperature and low air pressure at high altitude during use,

storage or transportation. Disposal of battery into ﬁre or a hot

oven, or mechanically crushing or cutting or the battery can

result in an explosion. Leaving the battery in an extremely

high temperature surrounding environment can result in an

explosion or the leakage of ﬂammable liquid of gas. Battery

subjected to extremely low air pressure may result in an

explosion or the leakage of ﬂammable liquid or gas. Dispose of

used battery according to the information in The RBRC seal.

7. Use only the adapters included with this product.

Incorrect adapter polarity or voltage can seriously

damage the product.

Power adapter information:

Parent unit output: 5V DC 1A

VTech Telecommunications Ltd.

Model: VT05EUS05100

Baby unit output: 5V DC 1A.

VTech Telecommunications Ltd.

Model: VT05EUS05100

Rechargeable battery information:

Li-ion battery, 3.8V 2100mAh

Zhongshan Tianmao Battery Co., Ltd.

Model Number: BP1763

8. The power adapters are intended to be correctly oriented

in a vertical or ﬂoor mount position. The prongs are not

designed to hold the plug in place if it is plugged into a

ceiling, under-the-table or cabinet outlet.

9. For pluggable equipment, the socket-outlet shall

be installed near the equipment and shall be easily

accessible.

10. Unplug this product from the wall outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth for

cleaning.

11. Do not cut off the power adapters to replace them with

other plugs, as this causes a hazardous situation.

12. Do not allow anything to rest on the power cords. Do not

install this product where the cords may be walked on or

crimped.

13. This product should be operated only from the type

of power source indicated on the marking label. If you

are not sure of the type of power supply in your home,

consult your dealer or local power company.

14. Do not overload wall outlets or use an extension cord.

15. Do not place this product on an unstable table, shelf, stand

or other unstable surfaces.

16. This product should not be placed in any area where

proper ventilation is not provided. Slots and openings

in the back or bottom of this product are provided for

ventilation. To protect them from overheating, these

openings must not be blocked by placing the product

on a soft surface such as a bed, sofa or rug. This product

should never be placed near or over a radiator or heat

17. Never push objects of any kind into this product through

the slots because they may touch dangerous voltage

points or create a short circuit. Never spill liquid of any

kind on the product.

18. To reduce the risk of electric shock, do not disassemble

this product, but take it to an authorized service facility.

Opening or removing parts of the product other than

speciﬁed access doors may expose you to dangerous

voltages or other risks. Incorrect reassembling can

cause electric shock when the product is subsequently

used.

19. You should test the sound reception every time you turn

on the units or move one of the components.

20. Periodically examine all components for damage.

21. There is a very low risk of privacy loss when using certain

electronic devices, such as baby monitors, cordless

telephones, etc. To protect your privacy, make sure the

product has never been used before purchase, reset

the baby monitor periodically by powering off and then

powering on the units, and power off the baby monitor

if you will not use it for some time.

22. Children should be supervised to ensure that they do not

play with the product.

23. The product is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their

safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between 32oF

and 104oF.

2. Do not expose the product to extreme cold, heat or

direct sunlight. Do not put the product close to a heating

source.

3. Batteries should not be exposed to excessive heat such as

bright sunshine or ﬁre.

4. Warning—Strangulation Hazard—

Children have STRANGLED in cords. Keep

this cord out of the reach of children (more

than 3 ft (0.9m) away). Do not remove this

tag.

5. Never place the baby unit(s) inside the baby’s crib or

playpen. Never cover the baby unit(s) or parent unit with

anything such as a towel or a blanket.

6. Other electronic products may cause interference

with your baby monitor. Try installing your baby

monitor as far away from these electronic devices

as possible: wireless routers, radios, cellular

telephones, intercoms, room monitors, televisions,

personal computers, kitchen appliances and cordless

telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless devices and

implanted cardiac pacemakers. Supported by the U.S. Food

and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the

pacemaker.

• Should NOT place wireless devices directly over the

pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless devices.

Electromagnetic ﬁelds (EMF)

This VTech product complies with all standards regarding

electromagnetic ﬁelds (EMF). If handled properly and

according to the instructions in this user’s manual, the product

is safe to be used based on scientiﬁc evidence available today.

Important safety instructions

Strangulation

Hazard

Keep this cord out of reach of children.

The cord needs to be at least three feet

away from the child at all times. Do not

use with an extension cord. Do not

remove this tag.

Éloignez ce cordon des enfants. Le

cordon doit se trouver à au moins trois

pieds d’un enfant et ce, en tout temps.

N’utilisez pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga este cable fuera de la alcance

de los niños. Este cable debe estar por

lo menos tres pies fuera de la alcance

del niño en todo momento. No lo use

con una extensión inalámbrica. No quite

esta etiqueta.

Risque

d’étranglement

Riesgo de

estrangulación

Strangulation

Hazard

Keep this cord out of reach of children.

The cord needs to be at least three feet

away from the child at all times. Do not

use with an extension cord. Do not

remove this tag.

Éloignez ce cordon des enfants. Le

cordon doit se trouver à au moins trois

pieds d’un enfant et ce, en tout temps.

N’utilisez pas de rallonge. Ne retirez pas

cette étiquette.

Mantenga este cable fuera de la alcance

de los niños. Este cable debe estar por

lo menos tres pies fuera de la alcance

del niño en todo momento. No lo use

con una extensión inalámbrica. No quite

esta etiqueta.

Risque

d’étranglement

Riesgo de

estrangulación

Power on

Power off>

< 3ft (1m)

3ft (1m)

> 3ft (1m)

Press and hold

Long press

1LED lights

2LCD display

3Microphone

4POWER

5TALK

6MENU/SELECT

7Arrow keys

8 Volume

9VIEW /LCD ON/OFF

10 /EXIT

11 Antenna

12 RESET

13 Stand

14 Power jack

1Light sensor

2Camera lens

3Microphone

4Night light

5On/Off switch

6On/Off LED light

• On when the baby unit is

turned on and is paired to the

parent unit.

• Flashes when the baby unit is

not being viewed;

or when the link to the parent

unit is lost.

7Light projector

8Speaker

9 Projection light on/off key

10 Night light on/off key

11 Power jack

12 Slots for wall mounting

x 2 x 2

1 set for VM5463

2 sets for VM5463-2

Need help?

≥

< 3ft (1m)

3ft (1m)

Press and hold

Parent unit icons

Main

menu Sub-menu

Brightness

• Adjust the parent unit’s LCD

brightness.

Camera

Monitoring mode (For VM5463-2 only)

• Single mode

• Split mode

• Patrol mode

Baby unit speaker volume

• Adjust the baby unit’s

speaker volume.

Lullaby

/ Play/Stop lullaby

• Select one of the soothing sounds, or

white noise.

• Select one of the ﬁve melodies.

• Play all melodies.

• Set timer to stop playing the selected

melody or soothing sound.

Main

menu Sub-menu

Night light

/ Turn on/off night light

• Select one of the night light colors.

• Change to all seven colors in cycles.

• Set timer to turn the night light off.

• Auto turn on the night light when baby

unit detects sound. It will turn off after

15 minutes of no sound detection.

See Sound sensitivity and sound

activation section to learn more.

A /

• Turn on/off the adaptive night light

feature. When this feature is on, the

baby unit detects the ambient light.

If the room is bright, the night light

adjusts itself to be brighter; if the

room is dim, the night light adjusts

itself to be less bright.

Projection

/ Turn on/off projection light

• Set timer to turn the projection light off.

• Auto turn on the projection light when

baby unit detects sound. It will turn off

after 15 minutes of no sound detection.

See Sound sensitivity and sound

activation section to learn more.

Temperature

Turn on/off temperature alert tone.

• Set the parent unit to beeps

whenever the room temperature

detected by the baby unit falls outside

of the set temperature range.

Main

menu Sub-menu

• Set the minimum temperature.

• Set the maximum temperature.

• Set temperature display in Fahrenheit

(oF) or Celsius (oC)

Alert tone settings

• Set the parent unit to beep when the

battery is low.

• Set the parent unit to beep when the

link between the parent unit and the

baby unit is lost.

• Set the conﬁrmation tone on or off

when selecting an option in the

menus.

• Set the parent unit to beep when the

baby unit detects sounds while in

Split mode (For VM5463-2 only).

Sound activation - screen and audio

/ Turn on/off sound activation

• When on, once a sound is detected,

the parent unit screen and speaker

will automatically turn on.

See Sound sensitivity and sound

activation section to learn more.

NOTESNOTE

Note

• When the parent unit screen is off

and it receives alerts, for example,

link lost between parent unit and

baby unit, the parent unit screen and

speaker will turn on for 10 seconds.

VOX (Voice Activated Alert) Sensitivity

• You can set VOX sensitivity level to

activate parent unit screen and sound

when baby unit detects sounds that

exceed certain levels. See Sound

sensitivity and sound activation

section to learn more.

Main menu icons

VM5463

VM5463-2

Long press

Power on

Long press

Power off

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss

resulting from the use of this user’s manual. VTech Communications, Inc. and its suppliers assume no

responsibility for any loss or claims by third parties that may arise through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada

Credits:

The Background Noise sound ﬁle was created by Caroline Ford,

and is used under the Creative Commons license.

The Stream Noise sound ﬁle was created by Caroline Ford, and is

used under the Creative Commons license.

The Crickets At Night sound ﬁle was created by Mike Koenig, and

is used under the Creative Commons license.

The Heart Beat sound ﬁle was created by Zarabadeu, and is used

under the Creative Commons license.

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Baby unit: 2405 - 2475 MHz

Parent unit: 2405 - 2475 MHz

Channels 32

LCD 5” Color LCD

(WQVGA 480x272 pixel)

Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may

vary according to environmental conditions at the time of use.

Power requirements Parent unit: 3.8V 2100mAh Li-ion battery

Baby unit power adapter: Output: 5V DC @ 1A

Parent unit power adapter: Output: 5V DC @ 1A

UL STD.

62368-1

CERTIFIED TO

CSA STD.

C22.2 NO.62368-1

CONFORMS TO

For operations and guides to help you operate your video

monitor, and for the latest information and support, check out our

online help topics and FAQs.

Use your smartphone or mobile device to access our online help.

• Go to https://help.vtechphones.com/vm5463 or

https://help.vtechphones.com/vm5463-2; OR

• Scan the QR code on the right. Launch the camera app or QR code scanner app

on your smartphone or tablet. Hold the device’s camera up to the QR code and

frame it. Tap the pop-up notification to be redirected to the online help page.

- If the QR code is not clearly displayed, adjust your camera’s focus by moving

your device closer or further away until the image is clear.

You can also call our Customer Support at 1 (800) 595-9511 [in US] or

1 (800) 267-7377 [in Canada] for help.

Night vision

The baby unit has infrared LEDs that

allow you to see your baby clearly at

night or in a dark room. When the baby

unit being viewed detects low light

levels, the infrared LEDs are switched

on automatically. The images from the

baby unit are in black and white, and

appears on the screen.

Notes

• It is normal if you see a short white glare on

your parent unit screen as the baby unit is

adapting to the dark environment.

• When the infrared LEDs are on, the images

are in black and white. This is normal.

Tip

• Depending on the surroundings and other

interfering factors, like lightings, objects,

colors and backgrounds, the video quality

may vary. Adjust the baby unit’s angle or

place the baby unit at a higher level to

prevent glare and blurry display.

Mount the baby unit on dry wall (optional)

For VM5463-2 only

If you are viewing baby unit , the

POWER LED light of baby unit

turns on. As baby unit is not being

viewed, its POWER LED light ﬂashes.

NOTESNOTE

Note

• If you power on only one baby unit, you may see the parent unit displaying and then , and

the LINK LED light ﬂashing.

• Press VIEW in Single CAM or Patrol mode to switch to the baby unit you have powered on.

Status check - Two baby units

Select Patrol as your monitoring mode to

alternately view the image from baby units

and every 10 seconds.

Change different views - Patrol

10s

Select Split as your monitoring

mode to view the images from both

baby units at once.

Change different views - Split

In Single CAM or

Patrol mode, press

VIEW to switch

between the image

of baby units

and .

Change different views - Single CAM

Sound sensitivity and sound activation

Sound activated screen and audioAdjust sound detection sensitivity

When Sound activation is on, the parent unit screen stays off

to save power when the baby unit detects no sound.

Once the baby unit detects sounds that are louder than the

chosen sound sensitivity level, the parent unit screen and

speaker turn on automatically. The parent unit will then turn

off again after 50 seconds of no sound detection.

NOTESNOTE

Note

• If you have muted the parent unit speaker, only the parent unit

screen will turn on when a sound is detected.

You can turn on Sound activation and adjust

the VOX sensitivity to detect sounds and

turn on the parent unit while its screen is

switched off or dimmed.

When the baby unit detects sounds that

exceed certain levels, the parent unit

screen will turn on and the baby unit starts

transmitting the sounds to the parent unit,

and you can see and hear your baby. If you

have turned on the Night light Auto-on and

the Projection light Auto-on feature, they

will turn on automatically to sooth your baby.

If you turn off Sound activation, you will hear

sounds from the baby unit all the time, even

when the parent unit screen is switched off.

If you have turned on sound alert, the parent

unit beeps when the baby unit detect sounds

while in Split mode (*For VM5463-2 only).

Mesures de sécurité importantes

La plaque signalétique appliquée est située au bas du socle

de l’unité du bébé.

Lorsque vous utilisez votre appareil, vous devriez toujours suivre

certaines mesures de précaution de base aﬁn de réduire les

risques d’incendie, d’électrocution et de blessures corporelles,

dont ceux qui suivent :

1. Observez toutes les instructions et mises en garde inscrites

sur l’appareil.

2. L’installation par un adulte est requise.

3. MISE EN GARDE: N’installez pas l’unité du bébé à une

hauteur supérieure à 2 mètres.

4. Ce produit ne remplace pas la surveillance adulte du

nourrisson. La supervision du nourrisson est la responsabilité

du parent ou de la personne qui s’occupe de l’enfant. Ce

produit pourrait cesser de fonctionner et, par conséquent,

vous ne devriez pas présumer qu’il continuera de fonctionner

correctement pendant une période de temps donnée. De

plus, il ne s’agit pas d’un instrument médical et ne devrait pas

être utilisé comme tel. Ce produit est destiné à vous aider à

superviser votre bébé.

5. N’utilisez pas cet appareil près de l’eau ni de toute autre

source d’humidité, par exemple, près d’une baignoire,

cuve à lessive, évier de cuisine, dans un sous-sol humide

ni près d’une piscine, dans un soussol humide ou une

douche.

6. MISE EN GARDE: Utilisez uniquement les piles fournies. Il

existe un risque d’explosion si un autre type de batterie est

utilisé pour l’unité Parents. N’incinérez pas les piles. Celles-

ci risqueraient d’exploser. Jetez les piles usées selon les

renseignements suivant le sceau du RBRC.

7. N’utilisez que les adaptateurs inclus avec ce produit.

L’utilisation d’un adaptateur dont la polarité ou la tension

serait inadéquate risque d’endommager sérieusement le

produit et mettre votre sécurité en péril.

Informations sur les adaptateurs électriques :

Adaptateur de l’unité du parent : Sortie : 5V DC 1A

VTech Telecommunications Ltd.

Modèle : VT05EUS05100

Adaptateur de l’unité du bébé : Sortie : 5V DC 1A

VTech Telecommunications Ltd.

Modèle : VT05EUS05100

Informations sur les piles rechargeables :

Li-ion battery, 3.8V 2100mAh

Zhongshan Tianmao Battery Co., Ltd.

Model Number: BP1763

8. Lorsqu’ils sont branchés dans une prise de courant, les

adaptateurs secteur ont été conçus pour être orientés

correctement, soit à la verticale ou au plancher. Les broches

n’ont pas été conçues pour supporter le poids du bloc

d’alimentation et le maintenir en place si celuici est branché

dans une prise au plafond, sous une table ou dans un

meuble.

9. Pour les PRODUITS À BRANCHER À UNE PRISE DE

COURANT, la prise de courant doit être installée près du

produit, aﬁn d’assurer une accessibilité sécuritaire à la prise

de courant.

10. Débranchez ce produit de la prise de courant avant de

procéder au nettoyage. N’utilisez pas de nettoyants en

aérosols. Utilisez un chiffon humide pour le nettoyer.

11. Ne coupez pas les cordons d’alimentation pour remplacer

les ﬁches, car ceci peut présenter un danger potentiel.

12. Ne laissez aucun objet reposer ni appuyer sur le cordon

d’alimentation. N’installez pas cet appareil dans un endroit

où l’on risque d’écraser le cordon d’alimentation ou de le

piétiner.

13. Ne faites fonctionner cet appareil qu’avec le type

d’alimentation indiqué sur l’étiquette. Si vous ne connaissez

pas le type d’alimentation que vous possédez à votre

domicile, consultez votre marchand ou votre compagnie

locale d’électricité.

14. Ne surchargez pas les prises de courant murales ni les

rallonges électriques.

15. Ne placez pas cet appareil sur un chariot, meuble, trépied,

support de montage ni table chancelants.

16. Les trous et ouvertures du boîtier, situés à l’arrière de

l’appareil ou sous celui-ci, servent à aérer l’appareil.

Pour l’empêcher de surchauffer, ne bloquez sous aucun

prétexte ces ouvertures et n’empêchez pas l’aération

adéquate de l’appareil en le plaçant sur un lit, divan,

tapis ou toute autre surface similaire. De même, ne le

positionnez pas à proximité ni au-dessus d’une source de

chaleur ou d’un calorifère. De plus, ne placez pas l’appareil

dans un endroit avant de vous assurer qu’il y ait une bonne

circulation d’air.

17. N’enfoncez jamais d’objets à travers les ouvertures de

cet appareil, car ils pourraient entrer en contact avec

des points de tension dangereux ou causer des courts-

circuits qui peuvent dégénérer en incendies ou en risques

d’électrocution. Ne renversez jamais de liquide dans ce

produit.

18. Aﬁn de réduire les risques d’électrocution, ne démontez

pas cet appareil, mais apportez-le dans un centre de service

autorisé. L’ouverture du boîtier ou le retrait de toutes pièces

que contient cet appareil, à l’exception de l’accès autorisé

à certaines portes ou ouvertures, risque de vous exposer à

des points de tension dangereux ou d’autres dangers. Un

remontage incorrect peut par la suite présenter des risques

d’électrocution.

19. Vous devriez tester la réception chaque fois que vous

mettez l’appareil en fonction.

20. Examinez les composantes aﬁn de vériﬁer si celles-ci ne

sont pas endommagées.

21. Il existe un très faible risque de perte de conﬁdentialité

avec certains appareils électroniques (autres écoute-bébés,

téléphones sans ﬁls etc.). Pour l’éviter, s’assurer que le

produit n’a jamais été utilisé avant l’achat, réinitialiser l’unité

de façon périodique, éteindre l’écoute-bébé quand il n’est

pas en cours d’utilisation.

22. Les enfants devraient être supervisés aﬁn de vous assurer

qu’ils ne jouent pas avec l’appareil.

23. Le produit n’est pas conçu pour être utilisé par des

personnes (incluant des enfants) aux capacités physiques,

sensorielles ou mentales réduites ou qui manquent

d’expérience et de connaissances, à moins qu’on leur

ait donné sufﬁsamment de supervision ou d’instructions

relativement à l’utilisation de l’appareil par une personne

responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

1. Utilisez et entreposez le produit à une température entre

0˚ C (32˚F) et 40˚C (104˚ F).

2. N’exposez pas cet appareil à des froids ou des chaleurs

extrêmes, ainsi qu’à la lumière directe du soleil. Ne

l’installez pas près d’une source de chauffage.

3. Le bloc-piles ne doit pas être exposé à la chaleur excessive

telle que la lumière du soleil ou au feu.

4. Avertissement - Risque de strangulation

- Les enfants se sont ÉTRANGLÉS dans des

cordons. Gardez ce cordon hors de portée

des enfants (à plus de 0,9 m). N’enlevez pas

cette étiquette.

5. Ne jamais placer le moniteur à l’intérieur du berceau

ou du parc de bébé. Ne jamais couvrir le moniteur ou

l’unité (s) portative avec un article tel une serviette ou une

couverture.

6. D’autres équipements électroniques peuvent produire des

interférences sur votre moniteur vidéo et audio. Tentez

d’installer votre moniteur vidéo ou audio à l’écart des

appareils électroniques tels que des routeurs sans fil, radios,

téléphones cellulaires, interphones, moniteurs, téléphones,

ordinateurs personnels, électroménagers et téléphones

sans fil.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs

numériques sans fil) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une

firme de recherche indépendante, a mené une évaluation

pluridisciplinaire des interférences entre les téléphones sans

fil portatifs et les stimulateurs cardiaques implantés dans

l’organisme. Appuyée par l’Administration des aliments et

drogues (FDA) des États-Unis, la firme WTR recommande aux

médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans fil à au moins six

pouces du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans fil directement

sur le stimulateur cardiaque, tel que dans une poche de

chemise, lorsque celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identifié de

risque pour les détenteurs de simulateurs cardiaques causés par

les gens qui utilisent dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes les normes se

rapportant aux champs électromagnétiques (EMF) standard. Si

vous le manipulez correctement en suivant les instructions de ce

guide, son utilisation sera sécuritaire pendant de nombreuses

années, selon les meilleures évidences scientifiques dont nous

disposons aujourd’hui.

For cETL compliance only

1. Place the wall mount bracket on a

wall and then use a pencil to mark

two holes in parallel. Remove the

wall mount bracket and drill two

holes in the wall (7/32 inch drill bit).

NOTESNOTE

Notes

• Check for reception strength and

camera angle before drilling the holes.

• The types of screws and anchors you

need depend on the composition of

the wall. You may need to purchase the

screws and anchors separately to mount

your camera units.

2. If you drill the holes into a stud, go

to step 3.

• If you drill the holes into an

object other than a stud, insert

the wall anchors into the holes.

Tap gently on the ends with a

hammer until the wall anchors

are ﬂush with the wall.

3. Align the wall mount bracket and screws with

the holes in the wall as shown. Tighten the screw

in the middle hole ﬁrst, so that the wall mount

bracket position is ﬁxed. You can tighten the

other screw in the top hole.

3. Insert the screws into the holes and

tighten the screws until only 1/4 inch of

the screws are exposed.

4. Place the camera unit on the wall

mount bracket, and then slide it

forward until it locks into place. Align

the holes on the wall mount bracket

with the screws on the wall, and slide

the wall mount bracket down until it

locks into place.

5. You can maximize your camera unit’s viewing angles by tilting the wall mount bracket.

Hold the camera unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket.

Tilt your camera unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the

joint and secure the angle.

4. Place the camera unit on the wall mount

bracket, and then slide it forward until

it locks into place. Connect the power

adapter to the camera unit and a power

supply not controlled by a wall switch.

Press VIEW

Parent unit icons (Cont’d)

VOX

Sensitivity

level Level 5

(Highest)

Level 4

(High)

Level 3

(Medium)

Level 2

(Low)

Level 1

(Lowest)

Description (Default setting)

The parent unit

screen and

speaker turn

on for very

small sounds,

including

background

noises from your

baby’s room.

The parent

unit screen

and speaker

turn on for soft

babbling and

louder sounds

from your baby.

The parent unit

remains quiet

when your

baby sleeps

soundly.

The parent unit

screen and

speaker turns

on for loud

babbling and

louder sounds

from your baby.

The parent unit

remains quiet

when your

baby makes

soft sounds.

The parent

unit screen

and speaker

turn on

for crying

and louder

sounds from

your baby.

The parent

unit remains

quiet when

your baby

makes soft

sounds.

The parent

unit screen

and speaker

turn on for

loud crying

or screeching

sounds from

your baby.

The parent

unit remains

quiet when

your baby

makes soft

sounds.

Status icons

Connection status

• - Strong signal strength.

• - Moderate signal

strength.

• - Low signal strength.

• - Weak signal strength.

Split mode

(*For VM5463-2 only)

Patrol mode

(*For VM5463-2 only)

Current view status

• The baby unit number that is

being viewed when in:

-Single CAM mode.

-Patrol mode

(*For VM5463-2 only).

-Split mode

(*For VM5463-2 only).

Night vision - On

Zoom - On

Lullaby - On

Night light - On

Night light - Auto-on

• Color icon indicates the night

light is set to auto-on, and is

currently turned on by sound

activation.

• Gray icon indicates the night

light is currently off but is set

to auto-on. Night light will turn

on when sound is detected by

the baby unit.

Status icons

Projection light - On

Projection light - Auto on

• Color icon indicates the

projection light is set to auto-

on, and is currently turned on

by sound activation.

• Gray icon indicates the

projection light is currently off

but is set to auto-on. Projection

light will turn on when sound is

detected by the baby unit.

oF or

oCReal-time temperature

• Real-time temperature

detected by the baby unit in

Fahrenheit (oF) or Celsius (oC)

(e.g. 57

oF or 14

oC).

Temperature alert tone - On

9-level sound indicator

• indicates low sound level

detected by the baby unit.

• indicates moderate

sound level detected by the

baby unit.

• indicates high

sound level detected by the

baby unit.

Mute alert

• Displays when the parent unit

speaker volume is set to off.

• Displays when the parent unit

is talking to the baby unit.

Battery status

• animates

when the battery is charging.

• - battery is fully charged.

• - battery is low and needs

charging.

Speaker volume - displays the

parent unit speaker volume level

while adjusting.

Alert icons

• Displays when parent unit’s battery is low and needs charging.

• Displays when connection between parent unit and baby unit is lost.

• Displays when sound is detected at a baby unit when in Split view.

(For VM5463-2 only)

• Baby unit detects temperature reaches or exceeds the set maximum.

• Baby unit detects temperature is at or is lower than the set minimum.

The parent unit display will dim to conserve energy after 10 minutes of inactivity, in

which there is neither key pressed nor alert received from the baby unit.

Dim mode

10 min inactivity

Press any button

Optimal position

Projection light

Tip

• The projection light located on the top of the baby unit projects a starry soft night light scene onto

the ceiling with a tilting angle. Adjust your baby unit’s position with the projection light to help

sooth your baby to sleep. For optimal performance, place the baby unit in upright position.

The RBRC seal on the Li-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an

industry program to collect and recycle these batteries at the end of their useful lives, when taken out of

service within the United States and Canada.

The program provides a convenient alternative to placing used Li-ion batteries into the trash or municipal

waste, which may be illegal in your area.

VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or

at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and

disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our

environment and conserving natural resources.

The RBRC seal and 1-800-8-BATTERY® are registered trademarks of Call2recycle, Inc.

The RBRC seal

This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor

is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge

the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby

units, the CEC battery charging testing mode is activated while it is powered off and charging.

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the

Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed

by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with

the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of

approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your

face.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development

Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause

interference. (2) This device must accept any interference, including interference that may cause undesired operation of the

device.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry Canada technical speciﬁcations were

met.

This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.

RF radiation exposure statement

The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should

be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other

accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect

to Canada’s Health Code 6 for Exposure of Humans to RF Fields.

California Energy Commission battery

charging testing mode

FCC and IC regulations

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the

holder of a valid proof of purchase (“Consumer” or “you”)

that the Product and all accessories provided in the sales

package (“Product”) are free from defects in material

and workmanship, pursuant to the following terms and

conditions, when installed and used normally and in

accordance with the Product operating instructions. This

limited warranty extends only to the Consumer for Products

purchased and used in the United States of America and

Canada.

What will VTech do if the Product is not free from defects

in materials and workmanship during the limited warranty

period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service

representative will replace at VTech’s option, without charge,

a Materially Defective Product. If we choose to replace

the Product, we may replace it with a new or refurbished

Product of the same or similar design. We will retain

defective parts, modules, or equipment. Replacement of the

Product, at VTech’s option, is your exclusive remedy. VTech

will return the replacement Products to you in working

condition. You should expect the replacement to take

approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE

(1) YEAR from the date of purchase (90 days on products

purchased as Refurbished*). This limited warranty also

applies to the replacement Product for a period of either (a)

90 days from the date the replacement Product is shipped

to you or (b) the time remaining on the original one-year

warranty (90-day limited warranty on products that are

purchased as Refurbished*); whichever is longer.

*Refurbished products purchased from our online store

carry a 90-day replacement warranty.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident,

shipping or other physical damage, improper installation,

abnormal operation or handling, neglect, inundation,

ﬁre, water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration

or modiﬁcation by anyone other than an authorized

service representative of VTech; or

3. Product to the extent that the problem experienced is

caused by signal conditions, network reliability, or cable or

antenna systems; or

4. Product to the extent that the problem is caused by use

with non-VTech accessories; or

5. Product whose warranty/quality stickers, product serial

number plates or electronic serial numbers have been

removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair

from outside the United States of America or Canada, or

used for commercial or institutional purposes (including

but not limited to Products used for rental purposes); or

7. Product returned without a valid proof of purchase (see

item 2 below); or

8. Charges for installation or set up, adjustment of customer

controls, and installation or repair of systems outside the

unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our

website at www.vtechphones.com or call 1 (800) 595-9511.

In Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s

manual - a check of the Product’s controls and features may

save you a service call.

Except as provided by applicable law, you assume the risk

of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in the

transport of the Product(s) to the service location. VTech

will return replaced Product under this limited warranty.

Transportation, delivery or handling charges are prepaid.

VTech assumes no risk for damage or loss of the Product in

transit.

What must you return with the Product to get warranty

service?

1. Return the entire original package and contents including

the Product to the VTech service location along with a

description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model) and

the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement

between you and VTech. It supersedes all other written or

oral communications related to this Product. VTech provides

no other warranties for this Product. The warranty exclusively

describes all of VTech’s responsibilities regarding the

Product. There are no other express warranties. No one is

authorized to make modiﬁcations to this limited warranty and

you should not rely on any such modiﬁcation. State/Provincial

Law Rights: This warranty gives you speciﬁc legal rights, and

you may also have other rights, which vary from state to state

or province to province.

Limitations: Implied warranties, including those of ﬁtness

for a particular purpose and merchantability (an unwritten

warranty that the Product is ﬁt for ordinary use) are limited

to one year from the date of purchase. Some states/

provinces do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.

In no event shall VTech be liable for any indirect, special,

incidental, consequential, or similar damages (including,

but not limited to lost proﬁts or revenue, inability to use

the Product or other associated equipment, the cost of

substitute equipment, and claims by third parties) resulting

from the use of this Product. Some states/provinces

do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion

may not apply to you.

Please retain your original sales receipt as proof

of purchase.

Limited warranty

VTech VM5463-2 Mode d'emploi

Marque: VTech

Modèle: VM5463-2

Catégorie: Moniteurs vidéo bébé

Taper: Mode d'emploi

Ce manuel convient également à

VM5463

Télécharger le PDF

rapport

dans d''autres langues

English: VTech VM5463-2 User guide

VTech VM5463-2 Mode d'emploi

Ce manuel convient également à

VTech VM5463-2 Mode d'emploi

dans d''autres langues

Documents connexes