VTech VM5261-2 Manuel utilisateur
- Catégorie
- Moniteurs vidéo bébé
- Taper
- Manuel utilisateur
Ce manuel convient également à
Note
• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should
not be used as such.
Test your baby monitor
You may test the baby monitor before initial use, and at regular times thereafter.
Caution
• For hearing protection, make sure the parent unit is
more than 3 feet (1 meter) away from both baby units. If
you hear any high-pitched noise, move the parent unit
further until the noise stops. You can also press on
the parent unit to reduce the noise.
1. Make sure your baby unit and parent unit are on.
2. The parent unit displays images from the baby unit.
• Speak towards the microphone of the baby unit.
You will hear the sound at the parent unit.
3. If you have two baby units, press VIEW on your parent unit. The screen switches to the
other baby unit. Then, repeat step 2.
Note
• When the parent unit displays and then No Link to CAM # (# represents the baby unit
number), and the LINK LED light flashes, move the parent unit closer to the baby unit (observe the
minimum distance of 3 feet / 1 meter).
Tip
• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the
baby units.
Positioning the baby monitor
Caution
• Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the
baby’s crib or playpen.
Note
• To avoid interference from other electronic
devices, place your baby monitor at least 3 feet (1
meter) away from devices such as wireless routers,
microwaves, cell phones and computers.
1. Place the baby unit more than 3 feet (1 meter) away from your baby.
2. Place the parent unit more than 3 feet (1 meter) away from the baby units to avoid
screeching noise.
Caution
• The default volume of your parent unit is level 4, and the maximum volume is level 7. If you experience
high-pitched screeching noise from your baby monitor while positioning:
- Make sure your baby unit and parent unit are more than 3 feet (1 meter) apart, OR
- Lower the volume of your parent unit.
Power on or off the baby unit
• Slide the ON/OFF switch to ON to turn on the baby unit. The ON/OFF LED light turns on.
• Slide the ON/OFF switch to OFF to turn off the baby unit. The ON/OFF LED light turns off.
Power on or off the parent unit
• Press and hold POWER to turn on the parent unit. The screen turns on.
• Press and hold POWER again to turn off the parent unit. The screen turns off.
Turn on or off the parent unit screen
You can turn on or off the parent unit screen without powering off the parent unit. You can
still hear sound from the baby units.
• Press and hold LCD ON/OFF on the parent unit to turn off the screen.
• Press any keys on the parent unit to turn on the screen again.
Adjust speaker volume
To adjust parent unit speaker volume:
• Press or on the parent unit at any time when viewing images.
To adjust baby unit speaker volume:
The baby unit speaker volume determines the lullaby volume and talkback volume
transmitted from parent unit. It can be adjusted in the parent unit.
1. Press MENU when the parent unit is idle.
2. Press or to choose Volume on CAM, then press SELECT.
3. Press or to choose the desired volume level, Level 1 is the softest while Level 5 is the
loudest. Then, press SELECT to confirm your selection.
Note
• Volume adjustment with the parent unit menu is available in Single CAM and Patrol mode only.
Lullaby
The baby monitor has five lullabies and four soothing sounds for you to comfort your baby.
You can play lullabies or soothing sounds on the baby unit by controlling remotely with the
parent unit.
To play lullabies using the parent unit:
1. Press MENU when the parent unit is idle.
2. Press or to choose Lullaby on CAM, then press SELECT.
3. Press or to choose Play Melodies, then press SELECT.
User’s manual
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
the latest VTech product news.
Congratulations
on purchasing your new VTech product. Before using this product, please read Important safety
instructions.
This manual has all the feature operations and troubleshooting necessary to install and operate
your new VTech product. Please review this manual thoroughly to ensure proper installation and
operation of this innovative and feature-rich VTech product.
For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.
1 set for VM5261
2 sets for VM5261-2
Adjust the sound sensitivity of the baby unit
You can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed
a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby
unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds
for transmitting to the parent unit. The VOX sensitivity level is preset to HIGHEST.
VOX
Sensitivity
level
Highest High Medium Low Lowest
Description The parent
unit speaker
is constantly
on, and you
will hear
all sounds
(including
background
noises) from
your baby’s
room.
The parent
unit speaker
turns on for
soft babbling
and louder
sounds from
your baby. It
remains quiet
when your
baby sleeps
soundly.
The parent
unit speaker
turns on for
loud babbling
and louder
sounds from
your baby. It
remains quiet
when your
baby makes
soft sounds.
The parent
unit speaker
turns on
for crying
and louder
sounds from
your baby. It
remains quiet
when your
baby makes
soft sounds.
The parent
unit speaker
turns on for
loud crying
or screeching
sounds from
your baby. It
remains quiet
when your
baby makes
soft sounds.
1. Press MENU when the parent unit is idle.
2. Press or to choose VOX Sensitivity, then press SELECT.
• If you have two baby units, the system prompts you to choose the desired baby unit or
both baby units, press or to choose ALL CAM or CAM #, then press SELECT.
3. Press or to choose the desired sensitivity level, then press SELECT to confirm your selection.
NOTESNOTE
Note
• As long as the Sound-activated screen setting is On, the screen will turn on automatically when VOX
sensitivity is triggered, despite it was off earlier.
Tips
• You can adjust the baby unit placement to improve the sound detection.
• If you want to use a sound machine or white noise machine for natural white noise while using this
babymonitor to check on your baby, you can:
- Lower the volume of your sound machine or white noise machine; or
- Lower the sensitivity level of your baby monitor to medium (level 3) or below. Default level is the
highest level.
Turn on or off the sound activation
When sound activation is on, as long as no sound is detected within 50 seconds, the parent
unit screen will turn off automatically to save power.
When your baby unit detects a sound, which exceeds the selected sensitivity level, the
sound activation triggers the parent unit screen to turn on automatically. When no sound is
detected within 50 seconds, the screen will be off again.
1. Press MENU when the parent unit is idle.
2. Press or to choose Sound-activated Screen, then press SELECT.
3. Press or to choose On or Off, then press SELECT to confirm your selection. The screen
returns to main menu.
Notes
• Sound activation is available in Single CAM and Patrol mode only.
• If the sound sensitivity is set to Highest, the parent unit screen may remain on continuously even
though sound activation is on. This depends on whether the baby unit detects any sounds.
Talk
You can use the TALK function of the parent unit to comfort your baby in Single CAM and
Patrol mode.
1. Press and hold TALK on the parent unit. The TALK light turns on.
2. Speak towards the microphone on the parent unit. Your voice is broadcast to the baby unit.
3. Release the TALK key to stop the broadcast.
Notes
• The parent unit speaker is muted during voice broadcast. Sound transmission from the baby unit
resumes after TALK is released.
• After around 20 seconds of sound re-transmission, the speaker returns to mute if you had set it to
mute before pressing TALK.
• The baby unit’s talkback volume can be adjusted via the parent unit menu.
Set alert tone
Low battery tone
You can set the parent unit to beep when the parent unit operates in low battery condition.
1. Press MENU when the parent unit is idle.
2. Press or to choose Tone, then press SELECT.
3. Press SELECT again to choose Low battery tone.
4. Press or to choose On or Off, then press SELECT to confirm your selection.
No link alert
You can set the parent unit to beep when the link between the parent unit and the baby unit is lost.
1. Press MENU when the parent unit is idle.
2. Press or to choose Tone, then press SELECT.
3. Press or to choose No link alert, then press SELECT.
4. Press or to choose On or Off, then press SELECT to confirm your selection.
Sound alert in split-view
You can turn on the sound alert feature so that, while in Split mode, the parent unit beeps
and displays Sound detected at CAM # whenever the baby unit detects sounds.
1. Press MENU when the parent unit is idle.
2. Press or to choose Tone, then press SELECT.
3. Press or to choose Sound alert in split-view, then press SELECT.
4. Press or to choose On or Off, then press SELECT to confirm your selection.
Note
• The sound alert feature is only available in Split mode.
Monitor the temperature
Your baby unit monitors the temperature of your baby’s room with its built-in temperature
sensor. If the detected temperature is out of the preset temperature range, the parent unit
will display an alert message.
Set temperature range
You can set the desired room temperature alert range. The minimum temperature can be set
between 52 oF (11 oC) and 69 oF (20 oC). The maximum temperature can be set between 70 oF
(21 oC) and 86 oF (30 oC).
1
Connect and charge the battery
What’s in the box
2
Before use
3
Using the baby monitor
3 Using the baby monitor (Con’t)
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Baby unit: 2405 - 2475 MHz
Parent unit: 2405 - 2475 MHz
Channels 32
LCD 5” Color LCD
(WQVGA 480x272 pixel)
Nominal effective range Maximum power allowed by FCC and IC. Actual operating range
may vary according to environmental conditions at the time of use.
Power requirements Parent unit: 3.7V Li-polymer battery
Baby unit power adapter: Output: 5V DC @ 800mA
Parent unit power adapter: Output: 5V DC @ 1A
Technical specifications
Specifications are subject to change without notice.
© 2019 VTech Communications, Inc.
All rights reserved. 02/19. VM5261-X_CIB_V4
Document order number: 91-010882-040-100
Operating range
The operating range of the baby monitor is up to 1000 feet (300 meters) outdoors. The
actual operating range may vary depending on the environmental conditions and other
interferences such as walls, doors and other obstructions.
4. Press or to choose a lullaby, or choose Play All, then press SELECT.
• If Play All is selected, the five lullabies will be played one after the other, until all of
them are played.
5. When the desired lullaby is selected, press or to choose Play, then press SELECT.
To play soothing sounds using the parent unit:
1. Press MENU when the parent unit is idle.
2. Press or to choose Lullaby on CAM, then press SELECT.
3. Press or to choose Play Soothing Sounds, then press SELECT.
4. Press or to choose a soothing sound, then press SELECT.
5. Press or to choose Play, then press SELECT.
Notes
• Lullaby playback control is available in Single CAM and Patrol mode only.
• The lullaby playback on the baby unit will be paused when receiving talkback from the parent
unit.
To stop lullabies or soothing sounds using the parent unit:
1. Press MENU when the parent unit is idle.
2. Press or to choose Lullaby on CAM, then press SELECT.
3. Press or to choose Stop, then press SELECT.
To set auto timer for lullaby:
While the baby unit is playing a lullaby or soothing sound, the auto timer feature automatically
stops the lullaby or soothing sound after playing for 15/30/45/60 minutes. You can set auto
timer for lullaby with the parent unit.
1. Press MENU when the parent unit is idle.
2. Press or to choose Lullaby on CAM, then press SELECT.
3. Press or to choose Auto Timer, then press SELECT.
4. Press or to choose the desired lullabies duration, then press SELECT to confirm your
selection.
After 15/30/45/60 minutes, the lullaby or soothing sound will stop automatically.
Set the language
You can select a language (English, French or Spanish) to be used in all screen displays.
1. Press MENU when the parent unit is idle.
2. Press or to choose Language, then press SELECT.
3. Press or to choose English, Français or Español, then press SELECT to confirm your
selection.
Adjust LCD brightness
You can change the brightness of the parent unit screen from Level 1 to Level 5. The LCD
brightness is preset to Level 3.
1. Press MENU when the parent unit is idle.
2. Press or to choose LCD, then press SELECT.
3. Press SELECT again to choose Brightness.
4. Press or to choose the desired level of brightness, then press SELECT to confirm
your selection.
Turn on and off the dim mode
The dim mode is preset to on to help you save the parent unit power. Your parent unit
display will dim automatically after 10 minutes of inactivity, in which there is neither key
pressed nor alert received from the baby unit.
1. Press MENU when the parent unit is idle.
2. Press or to choose LCD, then press SELECT.
3. Press or to choose Dim mode, then press SELECT.
4. Press or to choose On or Off, then press SELECT to confirm your selection.
NOTESNOTE
Note
• While the screen is dimmed, any keypress or alert message will trigger the screen to return to the
preset brightness level. After 10 minutes of inactivity, it will dim again.
Monitoring mode * for VM5261-2 only
Every time the parent unit is turned on, it displays a baby unit in Single CAM mode. If there
are two baby units in your system, you can also monitor your baby in Patrol or Split mode.
Single CAM The screen displays image of a single baby unit in full screen.
Patrol A single cam view that transitions to a different baby unit every 10 seconds.
Split The screen displays all baby units.
You can choose the desired monitoring mode.
1. Press MENU when the parent unit is idle.
2. Press or to choose Monitoring Mode, then press SELECT.
3. Press or to choose Single CAM, Patrol or Split, then press SELECT.
In Single CAM or Patrol mode:
• Press VIEW to view the next baby unit.
In Split mode:
• Press , , or to select a baby unit.
• Press or VIEW to view the selected baby unit temporarily in Single CAM mode. It returns
to Split mode after 10 seconds.
Note
• The parent unit is muted while in Split mode.
Pan, tilt, zoom
You can remotely pan and tilt your baby unit camera or zoom in while viewing images from
the baby unit in Single CAM and Patrol mode.
• Press and hold , , or to tilt the baby unit camera downward, upward, leftward or
rightward.
• Press to zoom in. Press again to zoom out.
• Press and hold , , or to move the zoomed image downward, upward, leftward
or rightward.
1. Press MENU when the parent unit is idle.
2. Press or to choose Temperature, then press SELECT.
3. Press or to choose Minimum or Maximum, then press SELECT.
• If you have two baby units, the system prompts you to choose the desired baby unit or
both baby units, press or to choose ALL CAM or CAM #, then press SELECT.
4. Press or to choose the desired minimum or maximum temperature, then press
SELECT to confirm your selection.
Temperature alert tone
You can turn on the temperature alert tone so that the parent unit will emit an alert tone if
the detected temperature is out of range.
1. Press MENU when the parent unit is idle.
2. Press or to choose Temperature, then press SELECT.
3. Press or to choose Alert tone, then press SELECT.
• If you have two baby units, the system prompts you to choose the desired baby unit or
both baby units, press or to choose ALL CAM or CAM #, then press SELECT.
4. Press or to choose On or Off, then press SELECT to confirm your selection.
Temperature format
You can choose to display the temperature in Fahrenheit (oF) or Celsius (oC).
1. Press MENU when the parent unit is idle.
2. Press or to choose Temperature, then press SELECT.
3. Press or to choose Format, then press SELECT.
4. Press or to choose oF or oC, then press SELECT to confirm your selection.
Rename the baby unit
You can rename the baby unit. Once the baby unit is renamed, its new name together with
the baby unit number will appear in the sub-menu of below options:
• VOX Sensitivity • Rename • Temperature
1. Press MENU when the parent unit is idle.
2. Press or to choose Rename, then press SELECT.
3. Press or to choose the desired baby unit, then press SELECT.
4. Press or to choose the desired name for the baby unit, then press SELECT to confirm
your selection.
Turn on or off the vibration
You can turn on the vibration feature so that the parent unit vibrates when it receives any of
these alerts (after turning on the respective alert tones):
• Sound alert in split-view • No link alert • Temperature alert tone
1. Press MENU when the parent unit is idle.
2. Press or to choose Vibration, then press SELECT.
3. Press or to choose On or Off, then press SELECT to confirm your selection.
Note
• If the vibration feature is turned on, the parent unit may vibrate as it receives sound broadcast from
the baby unit.
Press VIEW
> 3ft (1m)
1
2
Install the parent unit battery
The parent unit runs on rechargeable battery or AC power. To continuously monitor your
baby, keep the parent unit connected to AC power. With the battery alone, the parent unit can
cordlessly run for a short time only.
NOTESNOTE
• Use only the battery supplied with this product.
• If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible leakage.
Replace the battery
To replace the battery, press down on the battery compartment cover and pull it out, then
follow the steps above to install the battery.
Connect the baby monitor
NOTESNOTE
• Use only the power adapters supplied with this product.
• Make sure the baby monitor is not connected to a switch controlled electric outlet.
• Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not
designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table,
or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.
Charge the parent unit battery
When you have connected the parent unit and installed its battery for the first time or after power outage,
the parent unit powers on automatically. The battery icon indicates the battery status (see the following table).
NOTESNOTE
Notes
• The parent unit battery is fully charged after 3 hours of continuous charging.
• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time,
turn the parent unit off while charging.
• The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery.
Battery indicators Battery status Action
The battery icon is off and
displays .
No battery is installed but
operates using AC power,
or the battery has been
installed incorrectly.
Install the parent unit battery.
Charge without interruption (at
least 30 minutes).
The screen displays Battery
low at Parent Unit and .
The light flashes.
The battery has very little
charge and may be used
for only a short time.
Charge
without interruption
(about
30 minutes).
The battery icon becomes
solid . The battery is fully charged. To keep the battery charged, connect
it to AC power when not in use.
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
THIS SIDE UP
1
2
3
Press down
on the battery
compartment
cover to pull
it out.
Make sure the
label THIS SIDE
UP is facing up
while inserting
the battery.
Credits:
The Background Noise sound file was created by Caroline Ford, and is used under the Creative
Commons license.
The Stream Noise sound file was created by Caroline Ford, and is used under the Creative
Commons license.
The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative
Commons license.
The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons
license.
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
VM5261
VM5261-2
Full Color Video Monitor
with Wide-angle Lens
63ē
> 3ft (1m)
63ē
>
< 3ft (1m)
3ft (1m)
63ē
63ē
63ē
63ē
>
< 3ft (1m)
3ft (1m)
> 3ft (1m)
< 3ft (1m)
63ē
≥
< 3ft (1m)
3ft (1m)
63ē
63ē
≥
< 3ft (1m)
3ft (1m)
63ē
63ē
63ē
63ē
>
< 3ft (1m)
3ft (1m)
> 3ft (1m)
1
2
Status icons
Connection status
• displays when strong signal strength is detected between the baby unit
and the parent unit.
• or displays when moderate or low signal strength is detected between
the baby unit and the parent unit.
• displays when the link between the baby unit and the parent unit is lost.
Lullaby
• Displays when the baby unit being viewed is playing lullaby.
or
or
or
Current view status
• Displays the number of the baby unit that is being viewed when in Single CAM
and Patrol mode.
• Displays the baby unit number of the selected baby unit when in Split mode.
Patrol mode
• Displays when the parent unit is in Patrol mode.
• For VM5261-2 only.
Split mode
• Displays when the parent unit is in Split mode.
• For VM5261-2 only
Night vision
• Displays when the baby unit being viewed has activated the night vision feature.
Zoom
• Displays when the current image on the parent unit has zoomed in.
Temperature alert tone
• Displays when the temperature alert tone is set on.
oF or
oCReal-time temperature
• Displays the real-time temperature detected by the baby unit in Fahrenheit (oF)
or Celsius (oC) (e.g. 57
oF or 14
oC).
Mute alert
• Displays when the parent unit speaker unit volume is set to off.
• Displays when the parent unit is talking to the baby unit.
• Displays when Split mode is turned on.
9-level sound indicator
• (1 to 3 bars) indicates low sound level detected by the baby unit.
• (4 to 6 bars) indicates moderate sound level detected by the baby unit.
• (7 to 9 bars) indicates high sound level detected by the baby unit.
Speaker volume
• Displays the parent unit speaker volume level while adjusting.
Battery status
• animates when the battery is charging.
• displays solid when the battery is fully charged.
• displays when the battery is low and needs charging.
AC power without battery
• Displays when the parent unit is connected to AC power without the battery.
When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock
and injury, including the following:
1. Follow all warnings and instructions marked on the product.
2. Adult setup is required.
3. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parent’s or caregiver’s
responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for
any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist
you in supervising your baby.
4. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
5. CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion if a wrong type of battery is used for the
parent unit. Use only the supplied rechargeable battery or replacement battery pack (BT198555/BT298555) for the parent unit. Do
not dispose of batteries in a fire. They may explode. Dispose of used battery according to the information in The RBRC® seal.
6. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.
Baby unit power adapter: Output: 5V DC 800mA; Parent unit power adapter: Output: 5V DC 1A.
7. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.
8. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.
9. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
10. Unplug the power cords before replacing batteries.
11. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.
12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped.
13. This product should be operated only from the type of power source indicated on the marking label. If you are not sure
of the type of power supply in your home, consult your dealer or local power company.
14. Do not overload wall outlets or use an extension cord.
15. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
16. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back
or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be
blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or
over a radiator or heat register.
17. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or
create a short circuit. Never spill liquid of any kind on the product.
18. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility.
Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages
or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
19. You should test the sound reception every time you turn on the units or move one of the components.
20. Periodically examine all components for damage.
21. Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery
monitors, cordless phones, scanners, etc.
22. Children should be supervised to ensure that they do not play with the product.
23. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance
by a person responsible for their safety. SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between 32oF and 104oF.
2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.
3. Batteries should not be exposed to excessive heat such as bright sunshine or fire.
4. Make sure the baby unit(s) and the adapter cord(s) are always out of reach of the baby, at least 3 feet away from the
baby or crib, to avoid a possible strangulation hazard.
5. Never place the baby unit(s) inside the baby’s crib or playpen. Never cover the baby unit(s) or parent unit with anything
such as a towel or a blanket.
6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as
far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room
monitors, televisions, personal computers, kitchen appliances and cordless telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
The RBRC® seal on the lithium-ion battery indicates that VTech Communications, Inc. is voluntarily
participating in an industry program to collect and recycle these batteries at the end of their useful lives,
when taken out of service within the United States and Canada.
The RBRC® program provides a convenient alternative to placing used lithium-ion batteries into the trash
or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers
participating in the RBRC® program or at authorized VTech product service centers. Please call
1 (800) 8 BATTERY® for information on Li-ion battery recycling and disposal bans/restrictions in your area. VTech’s
involvement in this program is part of its commitment to protecting our environment and conserving natural resources.
RBRC® and 1 (800) 8 BATTERY® are registered trademarks of the Rechargeable Battery Recycling Corporation.
Mesures de sécurité importantes
Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de précaution de base afin de réduire les risques d’incendie,
d’électrocution et de blessures corporelles, dont ceux qui suivent :
1. Observez toutes les instructions et mises en garde inscrites sur l’appareil.
2. L’installation par un adulte est requise.
3. Ce produit ne remplace pas la surveillance adulte du nourrisson. La supervision du nourrisson est la responsabilité du parent ou de la
personne qui s’occupe de l’enfant. Ce produit pourrait cesser de fonctionner et, par conséquent, vous ne devriez pas présumer qu’il
continuera de fonctionner correctement pendant une période de temps donnée. De plus, il ne s’agit pas d’un instrument médical et ne
devrait pas être utilisé comme tel. Ce produit est destiné à vous aider à superviser votre bébé.
4. N’utilisez pas cet appareil près de l’eau ni de toute autre source d’humidité, par exemple, près d’une baignoire, cuve à lessive, évier de
cuisine, dans un sous-sol humide ni près d’une piscine, dans un soussol humide ou une douche.
5. MISE EN GARDE: Utilisez uniquement les piles fournies. Il existe un risque d’explosion si un autre type de batterie est utilisé pour l’unité
Parents. N’utilisez que le bloc-piles rechargeable inclus ou le bloc-piles de rechange (BT198555/BT298555). N’incinérez pas les piles. Celles-ci
risqueraient d’exploser. Jetez les piles usées selon les renseignements suivant le sceau du RBRC®.
6. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur dont la polarité ou la tension serait inadéquate risque
d’endommager sérieusement le produit et mettre votre sécurité en péril.
Adaptateur de l’unité du bébé : Sortie : 5V CC 800mA
Adaptateur de l’unité du parent : Sortie : 5V CC 1A
7. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs secteur ont été conçus pour être orientés correctement, soit à la verticale
ou au plancher. Les broches n’ont pas été conçues pour supporter le poids du bloc d’alimentation et le maintenir en place si celuici est branché
dans une prise au plafond, sous une table ou dans un meuble.
8. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise de courant doit être installée près du produit, afin d’assurer une
accessibilité sécuritaire à la prise de courant.
9. Débranchez ce produit de la prise de courant avant de procéder au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un chiffon
humide pour le nettoyer.
10. Débranchez les cordons d’alimentation avant de remplacer le bloc-piles.
11. Ne coupez pas les cordons d’alimentation pour remplacer les fiches, car ceci peut présenter un danger potentiel.
12. Ne laissez aucun objet reposer ni appuyer sur le cordon d’alimentation. N’installez pas cet appareil dans un endroit où l’on risque d’écraser
le cordon d’alimentation ou de le piétiner.
13. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur l’étiquette. Si vous ne connaissez pas le type d’alimentation que
vous possédez à votre domicile, consultez votre marchand ou votre compagnie locale d’électricité.
14. Ne surchargez pas les prises de courant murales ni les rallonges électriques.
15. Ne placez pas cet appareil sur un chariot, meuble, trépied, support de montage ni table chancelants.
16. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de surchauffer,
ne bloquez sous aucun prétexte ces ouvertures et n’empêchez pas l’aération adéquate de l’appareil en le plaçant sur un lit, divan, tapis ou
toute autre surface similaire. De même, ne le positionnez pas à proximité ni au-dessus d’une source de chaleur ou d’un calorifère. De plus,
ne placez pas l’appareil dans un endroit avant de vous assurer qu’il y ait une bonne circulation d’air.
17. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou
causer des courts-circuits qui peuvent dégénérer en incendies ou en risques d’électrocution. Ne renversez jamais de liquide dans ce produit.
18. Afin de réduire les risques d’électrocution, ne démontez pas cet appareil, mais apportez-le dans un centre de service autorisé. L’ouverture du
boîtier ou le retrait de toutes pièces que contient cet appareil, à l’exception de l’accès autorisé à certaines portes ou ouvertures, risque de vous
exposer à des points de tension dangereux ou d’autres dangers. Un remontage incorrect peut par la suite présenter des risques d’électrocution.
19. Vous devriez tester la réception chaque fois que vous mettez l’appareil en fonction.
20. Examinez les composantes afin de vérifier si celles-ci ne sont pas endommagées.
21. Soyez avisé de la perte de la confidentialité lorsque vous utilisez les ondes publiques. Les conversations peuvent être entendues par
d’autres moniteurs de bébé, des téléphones sans fil, des scanneurs, etc.
22. Les enfants devraient être supervisés afin de vous assurer qu’ils ne jouent pas avec l’appareil.
23. Le produit n’est pas conçu pour être utilisé par des personnes (incluant des enfants) aux capacités physiques, sensorielles ou mentales
réduites ou qui manquent d’expérience et de connaissances, à moins qu’on leur ait donné suffisamment de supervision ou d’instructions
relativement à l’utilisation de l’appareil par une personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
1. Utilisez et entreposez le produit à une température entre 0˚ C (32˚F) et 40˚C (104˚ F).
2. N’exposez pas cet appareil à des froids ou des chaleurs extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une source de chauffage.
3. Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que la lumière du soleil ou au feu.
4. Assurez-vous que le moniteur et le cordon de l’adaptateur sont toujours hors de portée des enfants, àau moins 1 mètre (3 pieds) de l’enfant ou
du berceau, pour éviter tout risque de strangulation.
5. Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec un article
tel une serviette ou une couverture.
6. D’autres équipements électroniques peuvent produire des interférences sur votre moniteur vidéo et audio. Tentez d’installer votre moniteur
vidéo ou audio à l’écart des appareils électroniques tels que des routeurs sans fil, radios, téléphones cellulaires, interphones, moniteurs,
téléphones, ordinateurs personnels, électroménagers et téléphones sans fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené une évaluation pluridisciplinaire des
interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des
aliments et drogues (FDA) des États-Unis, la firme WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
• Vous devriez maintenir les dispositifs sans fil à au moins six pouces du simulateur cardiaque.
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the
Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship,
pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product
operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United
States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period
(“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without
charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we
choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will
retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive
remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or
replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces
a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or
replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you
or (b) the time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal
operation or handling, neglect, inundation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service
representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna
systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed,
altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for
commercial or institutional purposes (including but not limited to Products used for rental purposes); or
7. Product returned without a valid proof of purchase (see item 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In
Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save
you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are
responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return
repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech
assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or
proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the
cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of
Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location along with a
description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of
purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral
communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes
all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one is authorized to make
modifications to this limited warranty and you should not rely on any such modification. State/Provincial Law Rights: This warranty
gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty
that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech
be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or
revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third
parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor
is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge
the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby
units, the CEC battery charging testing mode is activated while it is powered off and charging.
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the
Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a
user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC
criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 8
in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications
were met.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
RF radiation exposure statement
The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should
be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect
to Canada’s Health Code 6 for Exposure of Humans to RF Fields.
The RBRC® seal
For cETL compliance only Limited warranty
California Energy Commission battery
charging testing mode
The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room.
When the baby unit being viewed detects low light levels, the infrared LEDs are switched on
automatically. The images from the baby unit are in black and white, and appears on the screen.
Notes
• It is normal if you see a short white glare on your parent unit screen as the baby unit is adapting to
the dark environment.
• When the infrared LEDs are on, the images are in black and white. This is normal.
Tip
• Depending on the surroundings and other interfering factors, like lightings, objects, colors and
backgrounds, the video quality may vary. Adjust the baby unit’s angle or place the baby unit at a
higher level to prevent glare and blurry display.
Night vision
Your baby monitor comes ready for tabletop use. You can also choose to mount your baby
monitor on the wall. See Mount the baby unit (optional) in the Quick Start Guide for the wall
mounting instructions.
Mount the baby unit (optional)
FCC and IC regulations
Below are the questions most frequently asked about the baby monitor. If you cannot find the answer to your question,
visit our website at www.vtechphones.com, or contact 1 (800) 595-9511 for customer service.
Why does the
baby monitor
not respond
normally?
Try the following (in the order listed) for common cure:
1. Disconnect the power to the baby units and the parent unit.
2. Remove the batteries in the parent unit. Then, install the batteries again.
3. Wait a few seconds before connecting power back to the baby units and the parent unit.
4. Turn on the baby units and the parent unit.
5. Wait for the parent unit to synchronize with the baby units. Allow up to one minute for
this to take place.
Why don’t the
power-on light of the
baby unit and parent
unit go on when I switch
on the units?
Perhaps the parent unit is not connected to the power. Insert the appliance plug into the
parent unit and put the adapter in a wall socket. Then, press and hold POWER to switch on
the parent unit and to establish connection with the baby unit.
Perhaps the baby unit is not connected to the power. Insert the appliance plug into the
baby unit and put the adapter in a wall socket. Then, slide the ON/OFF switch to ON to
switch on the baby unit and to establish connection with the parent unit.
Why doesn’t my parent
unit charge while
connected to AC power?
Make sure the power is not controlled by a wall switch.
Make sure the battery is correctly installed in your parent unit.
You may have used the battery for a long time. Replace a new battery.
Why is my screen in black
and white? The screen is in black and white during night-time or in a dark room when the night vision
feature is activated. This is normal.
Why do I get glare or
blurry display on my
screen when viewing my
baby at night?
During night-time or in a dark room, the surroundings and other interfering factors, like
lightings, objects, colors and backgrounds may affect the image quality on your parent unit
screen. Adjust the baby unit’s angle or place the baby unit at a higher level to prevent glare
and blurry display.
Why does the baby
monitor produce a
high-pitched noise?
The parent unit and baby units may be too close to each other.
• Move the parent unit away from the baby units until the noise stops; OR
• Turn down the volume of your parent unit.
Why does the parent unit
beep? The baby units may be out of range. Move the parent unit closer to the baby units (but not
less than 3 feet).
The parent unit may not have enough charge for the parent unit to perform normally.
Charge the battery in the parent unit for up to 3 hours.
If your parent unit is in Split mode, some of your baby units may detect sounds.
The temperature of your baby’s room may be too high or too low.
Why does the parent unit
beep/vibrate frequently
in Split mode?
You may have set the VOX sensitivity level to Highest when the sound alert (and vibration)
feature is turned on. The parent unit notifies you of all sounds including background noise
with beeps (and vibration). Adjust the VOX sensitivity to a lower level.
Why does the parent unit
react too quickly to other
sounds?
The baby unit also picks up other sounds than those of your baby. Adjust the VOX sensitivity
level to a lower level or lower the parent unit speaker volume.
Why don’t I hear a sound/
Why can’t I hear my baby
cry?
The parent unit speaker volume may be too low. Press to increase the volume.
You may have set a low VOX sensitivity level. See Adjust the sound sensitivity of the baby
unit to set to a higher level.
Frequently asked questions
When you are not going to use the baby monitor for some time, remove the rechargeable battery from the
parent unit. Store the parent unit, the baby unit and the adapters in a cool and dry place.
Storage
Parent unit icons
Important safety instructions
1Antenna
2Temperature sensor
3 ON/OFF switch
• Slide to turn on or off the baby unit.
4ON/OFF LED light
• On when the baby unit is turned on
and is paired to the parent unit.
• Flashes when the baby unit is not
being viewed; or when the link to
the parent unit is lost.
5Light sensor
6Camera
7Infrared LEDs
8Microphone
9Speaker
10 Power jack
11 Threaded socket
• For wall mount installation use.
12 PAIR
• Your baby units and parent unit
provided are already paired.
Baby unit overview
Main menu icons
Monitoring mode
• If you have two baby units, you can select a monitoring mode (Single CAM, Patrol or Split).
• For VM5261-2 only.
Tone
You can set the parent unit to beep
• when the parent unit operates in low battery condition;
• when the link between the parent unit and the baby unit is lost; or
• when the baby unit detects sounds while in Split mode.
• with each key press.
Language
• You can select a language (English, French or Spanish) to be used in all screen displays.
LCD
• You can change the brightness of the parent unit screen, or turn on the Dim Mode
to save power.
Rename
• You can choose a specific name for the baby unit from a pre-defined name list.
VOX Sensitivity
• With this feature, you can choose to hear sounds from the baby unit all the time, or
to hear sounds that exceed a certain level. You can use the parent unit to adjust the
microphone sensitivity of your baby unit. The higher the sensitivity level, the more
sensitive the baby unit is in detecting sounds for transmitting to the parent unit.
Sound-activated Screen
• When the baby unit detects no sound, the parent unit screen stays off to save
power. Once a sound is detected, the parent unit screen turns on automatically. It
will then turn off again after 50 seconds of no sound detection.
Temperature
• You can choose to set the maximum/ minimum temperature and turn on the
Temperature alert tone, so that the parent unit beeps whenever the room
temperature detected by the baby unit falls outside of the desired temperature range.
• You can choose to display the temperature in Fahrenheit (oF) or Celsius (oC) on your
parent unit.
Lullaby on CAM
• You can choose a lullaby or soothing sound to comfort your baby.
Volume on CAM
• You can adjust the volume of baby units which determines the lullaby volume and
talkback volume transmitted from parent unit.
Vibration
• You can turn on the vibration alert so that the parent unit vibrates when it receives
No link alert, Sound alert in split-view or Temperature alert tone after turning on
the respective alert tones.
Warning icons and messages
No link to CAM # *The selected baby unit is out of range or is turned off.
Battery low at
Parent Unit The battery level of the parent unit is very low and needs to be
recharged.
Battery empty.
Powering off ... The battery is empty and needs to be recharged.
Sound detected at
CAM # The sound level exceeds the threshold at CAM # in Split mode.
Temperature
too high at CAM #
or
Temperature
too low at CAM #
The temperature detected by the baby unit is higher/lower than
the desired temperature alert range.
Powering on... The parent unit is turning on.
The parent unit is searching for baby units.
Auto Timer of lullaby is
reset
The timer that determines the remaining play time for the lullabies
is restarted.
The parent unit has just been connected to AC power.
* # represents the baby unit number.
To keep this product working well and looking good, follow these guidelines:
• Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or
fluorescent lamps).
General product care
Your baby monitor comes with a wide-angle lens. You can install the lens to view more of your
baby’s room from the parent unit screen. See Install the lens (optional) in the Quick Start Guide
for the lens installation instructions.
Install the lens (optional)
• Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en
marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques causés par les gens qui utilisent
dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes les normes se rapportant aux champs électromagnétiques (EMF) standard. Si vous le manipulez
correctement en suivant les instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années, selon les meilleures
évidences scientifiques dont nous disposons aujourd’hui.
Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless devices at least six inches from the pacemaker.
• Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to
the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today.
Why can’t I establish a
connection? Why is the
connection lost every now
and then? Why are there
sound interruptions?
The baby units may be out of range. Move the parent unit closer to the baby units (but not
less than 3 feet).
Other electronic and wireless products may cause interference with your baby monitor. Try
installing your baby monitor as far away from these devices as possible.
If you power on only one baby unit, your parent unit may display and No link to CAM #,
and the LINK LED light flashes. Press VIEW to switch to the baby unit you have powered on.
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry before you connect them to the mains again.
1
2
3
4
5
6
8
9
9
10
11
12
13
7
11
12
1
2
3
4
5
6
7
8
10
11
12
Parent unit overview (Con’t)
1 LED lights
Indicate the different statuses of the
parent unit. For details, refer to Parent
unit lights.
2LCD display
3VOL
4 VOL
5 Zoom
• Press to zoom in or out.
Parent unit overview
6VIEW / LCD ON/OFF
7Microphone
8POWER
9TALK
• Press and hold to talk to the
selected baby unit.
10
• While in a menu, press to return to
the main menu or idle screen.
• While viewing images in Single
CAM or Patrol mode, press and
hold to pan the baby unit camera
leftward.
• While viewing zoomed image,
press and hold to move the
zoomed image leftward.
• While in Split mode, press to move
the selection box leftward.
11
• While in a menu, press to scroll up.
• While viewing images in Single
CAM or Patrol mode, press and
hold to tilt the baby unit camera
upward.
• While viewing zoomed image,
press and hold to move the
zoomed image upward.
12
• While in a menu, press to choose
an item.
• While viewing images in Single CAM
or Patrol mode, press and hold to
pan the baby unit camera rightward.
• While viewing zoomed image,
press and hold to move the
zoomed image rightward.
• While in Split mode, press to move
the selection box rightward.
13 MENU/SELECT
• Press to enter the menu.
• While in a menu, press to choose an
item, or save a setting.
14
• While in a menu, press to scroll down.
• While viewing images in Single CAM
or Patrol mode, press and hold to tilt
the baby unit camera downward.
• While viewing zoomed image,
press and hold to move the
zoomed image downward.
15 Antenna
16 Stand
17 Speaker
18 Power jack
19 Battery compartment cover
Parent unit lights
LINK • On when the parent unit is linked to the baby unit.
• Flashes when the link to the baby unit being viewed in Single CAM or Patrol mode
is lost; or when the link to at least one baby unit being viewed in Split mode is lost.
• On when the parent unit is connected to AC power, or the battery is charging.
• Flashes when the parent unit battery is low and needs charging.
• Off when the parent unit is disconnected from AC power.
• On when the speaker volume of the parent unit is turned off; or when the parent
unit is talking to the baby unit; or when the parent unit is in Split mode.
TALK • On when the parent unit is talking to the baby unit.
-
1
-
2
VTech VM5261-2 Manuel utilisateur
- Catégorie
- Moniteurs vidéo bébé
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: VTech VM5261-2 User manual
Documents connexes
-
VTech VM4263 Guide de démarrage rapide
-
-
-
-
-
-
VTech VM5463 Mode d'emploi
-
-
VTech VM320 Manuel utilisateur
-