VTech VM4263 Guide de démarrage rapide

Catégorie
Moniteurs vidéo bébé
Taper
Guide de démarrage rapide
VM4263
VM4263-2
3.5” Video Baby Monitor
with Night Light
Go to www.vtechphones.com
to register your product for enhanced
warranty support and the latest VTech
product news.
1 Connect the baby monitor
2
Power on or off the baby monitor
What’s in the box
4
Status check
Once you power on both
your baby unit and parent
unit, your parent unit
displays image from the
baby unit, and the LINK
LED light turns on.
3 Positioning the baby monitor
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
Strangulation
Hazard
Keep this cord out of reach of children.
The cord needs to be at least three feet
away from the child at all times. Do not
use with an extension cord. Do not
remove this tag.
Éloignez ce cordon des enfants. Le
cordon doit se trouver à au moins trois
pieds d’un enfant et ce, en tout temps.
N’utilisez pas de rallonge. Ne retirez pas
cette étiquette.
Mantenga este cable fuera de la alcance
de los niños. Este cable debe estar por
lo menos tres pies fuera de la alcance
del niño en todo momento. No lo use
con una extensión inalámbrica. No quite
esta etiqueta.
Risque
d’étranglement
Riesgo de
estrangulación
Quick start guide
Talk to your baby unit
Press and hold TALK and speak to your
parent unit. Your voice is transmitted
to the baby unit. Release TALK when
finished talking and hear your baby again.
Basic operation - Parent unit
Overview - Parent unit
The applied nameplate is located at the bottom of the baby unit’s
base.
When using your equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and
injury, including the following:
1. Follow all warnings and instructions marked on the product.
2. Adult setup is required.
3. CAUTION: Do not install the baby unit at a height above 6.5
feet (2 meters).
4. This product is intended as an aid. It is not a substitute for
responsible and proper adult supervision and should not be
used as such.
5. This product is not intended for use as a medical monitor.
6. Do not use this product near water, for example, near to a
bath, sink, swimming pool or shower.
7. CAUTION: Use only the battery provided (if applicable). There
may be a risk of explosion if a wrong type of battery is used
for the parent unit. The battery cannot be subjected to high or
low extreme temperature and low air pressure at high altitude
during use, storage or transportation. Disposal of battery in
fire or a hot oven, mechanically crushing or cutting the battery
can result in an explosion. Leaving the battery in an extremely
high temperature surrounding environment can result in an
explosion or the leakage of flammable liquid of gas. Battery
subjected to extremely low air pressure may result in an ex-
plosion or the leakage of flammable liquid or gas. Dispose of
used battery according to the information in The RBRC seal.
8. Use only the power adapters included with this product.
Incorrect power adapter polarity or voltage can seriously
damage the product.
Power adapter information:
Output: 5V DC 1A
VTech Telecommunications Ltd.
Model: VT05EUS05100
-OR-
Jiangxi Jian Aohai Technology Co., Ltd.
Model: A318-050100W-US2
Rechargeable battery information:
Zhuhai Great Power Energy Co., Ltd.
Li-ion battery, 3.6V, 2600mAh, 9.36Wh;
Model: ICR18650-2.6Ah-3.6V-1S1P
9. The power adapter is intended to be correctly oriented in a
vertical or floor mount position. The prongs are not designed
to hold the plug in place if it is plugged into a ceiling, un-
der-the-table or cabinet outlet.
10. For pluggable equipment, the socket-outlet (power adapter)
should be installed near the equipment and should be easily
accessible.
11. Unplug this product from the wall outlet before cleaning.
Do not use liquid or aerosol cleaners. Use a damp cloth for
cleaning.
12. Do not modify the power adapters or replace with other
adapters, as this causes a hazardous situation.
13. Do not allow anything to rest on the power cords. Do not
install this product where the cords may be walked on or
crimped.
14. This product should be operated only from the type of
power source indicated on the marking label. If you are not
sure of the type of power supply in your home, consult your
dealer or electricity supply provider.
15. Do not overload wall outlets or use an extension cord.
16. Do not place this product on an unstable table, shelf, stand or
other unstable surfaces.
17. This product should not be placed in any area where proper
ventilation is not provided. Slots and openings in the back
or bottom of this product are provided for ventilation. To
protect them from overheating, these openings must not be
blocked by placing the product on a soft surface such as a
bed, sofa or rug. This product should never be placed near
or over a radiator or heat source.
18. Never push objects of any kind into this product through the
slots because they may touch dangerous voltage points or cre-
ate a short circuit. Never spill liquid of any kind on the product.
19. To reduce the risk of electric shock, do not disassemble this
product, but take it to an authorized service facility. Disas-
sembling or removing parts of the product other than via the
battery door (if applicable) may expose you to dangerous
voltages or other risks. Incorrect reassembling can cause
electric shock when the product is subsequently used.
20. You should test the sound reception every time you turn on
the units or move one of the components.
21. Periodically examine all components for damage.
22. There is a very low risk of privacy loss when using certain
electronic devices, such as baby monitors, cordless tele-
phones, etc. To protect your privacy, make sure the product
has never been used before purchase, reset the baby
monitor periodically by powering off and then powering
on the units, and power off the baby monitor if you are not
intending to use it for some time.
23. Children should be supervised to ensure that they do not
play with the product.
24. The small parts of this monitor can be swallowed by babies or
small children. Keep these parts out of reach of children.
25. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental capabili-
ties, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
Use and store the product at a temperature between 32oF
(0oC) and 104oF (40oC).
Mishandling batteries can cause burn, fire or explosion
hazards.
Batteries should not be exposed to excessive heat such as
bright sunshine or fire.
Do not expose the product to extreme cold, heat or direct
sunlight. Do not put the product close to a heating source.
Warning—Strangulation Hazard—Chil-
dren have STRANGLED in cords. Keep this cord
out of the reach of children (more than 3 ft
(0.9m) away). Do not remove warning label on
the adapter cord.
Never place the camera unit(s) inside the baby’s crib or
playpen. Never cover the camera unit(s) or parent unit with
anything such as a towel or a blanket.
Other electronic products may cause interference with your
camera unit. Try installing your camera unit as far away from
these electronic devices as possible: wireless routers, radios,
cellular telephones, intercoms, room monitors, televisions,
personal computers, kitchen appliances and cordless tele-
phones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and implanted
cardiac pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
Should keep wireless devices at least six inches from the
pacemaker.
Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless devices.
Electromagnetic elds (EMF)
This VTech product complies with all standards regarding
electromagnetic fields (EMF). If handled properly and according
to the instructions in this user’s manual, the product is safe to be
used based on scientific evidence available today.
Important safety instructions
1 set for VM4263
2 sets for VM4263-2
Connect the baby unit to a power
supply to turn it on. Disconnect the
baby unit to turn it off.
Press and hold POWER to power on or off
your parent unit.
Caution
The default volume of your parent unit
is level 3, and the maximum volume
is level 5. If you experience feedback
noise from your baby monitor while
positioning:
- Make sure your baby unit and parent unit
are more than 3 feet (1 meter) apart, OR
- Turn down the volume of your parent unit.
NOTESNOTE
Note
To avoid interference from other electronic
devices, place your baby monitor at least 3 feet
(1 meter) away from devices such as wireless
routers, microwaves, mobile phones and
computers.
Turn off the screen
Press POWER/LCD OFF to switch off the
screen. You can still hear sound from the
selected baby unit.
Tip
Press any key on the parent unit to turn on
the screen again.
Use the menu
Press MENU to enter the menu, or save a setting. You can use the parent unit for advanced
settings or operations, such as to play or stop the baby unit’s lullaby, or to adjust the baby
unit’s sound sensitivity.
While in the menu:
Press or to scroll among the
menu options.
Press or to select an item.
Press SELECT to confirm your
selection.
Press TALK/EXIT to exit the
menu and return to live view.
Quick start guide VM4263 VM4263-2
For more support information
S
m
NOTESNOTE
The rechargeable battery in the parent unit is built-in.
Use only the power adapters supplied with this product.
Make sure the parent unit and the baby unit are not connected to the switch controlled electric power
outlets.
Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not designed
to hold the weight of a baby monitor, so do not connect them to any ceiling, under-the-table, or cabinet
outlets. Otherwise, the adapters may not properly connect to the outlets.
Make sure the parent unit, the baby units and the power adapter cords are out of reach of children.
Parent unit icons
Caution
Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the
baby’s crib or playpen.
Overview - Baby unit
For operations and guides to help you using your video monitor, and for
latest information and supports, go and check the online help topics and
online FAQs.
Use your smartphone or mobile device to access our online
help.
Go to https://help.vtechphones.com/VM4263 or
https://help.vtechphones.com/VM4263-2; OR
Scan the QR code on the right. Launch the camera app or
QR code scanner app on your smartphone or tablet. Hold
the device’s camera up to the QR code and frame it. Tap the
notification to trigger the redirection of the online help.
- If the QR code is not clearly displayed, adjust your
camera’s focus by moving your device closer or further
away until it is clear.
You can also call our Customer Support at 1 (800) 595-9511 [in US] or
1 (800) 267-7377 [in Canada] for help.
Need help?
S
m
VM4263
VM4263-2
Main menu icons
Zoom
1. Press MENU when in idle mode.
2. Choose , and select .
3. Press or to choose (Zoom in)
or (Zoom out), then press SELECT to
confirm your selection.
Status icons
Connection status
or displays when strong signal strength is detected between the
baby unit and the parent unit.
or displays when moderate or low signal strength is detected between
the baby unit and the parent unit.
Patrol mode
Displays when the parent unit is in PATROL mode (For VM4263-2 only).
or Current view status
Displays the baby unit number that is being viewed.
Zoom
Displays when the current image on the parent unit has zoomed in.
Night vision
Displays when the baby unit being viewed has activated the night vision
feature.
Talkback
Displays when talking back to the baby units from parent unit.
Lullaby
Displays when a lullaby is playing.
Night light
Displays when the baby unit’s night light is turned on.
Displays when the night light Auto-on feature is activated, but not yet
triggered by sound.
Displays when the baby unit’s night light has been triggered to turn on
automatically by sound.
Mute alert
Displays when the parent unit speaker volume is set to zero.
Displays when the parent unit is talking to the baby unit.
or
Real-time temperature
Displays the real-time temperature detected by the baby unit in Fahrenheit
(oF) or Celsius (oC) (e.g. 57
oF or 14
oC).
Battery status
animates when the battery is charging.
displays solid when the battery is fully charged.
displays when the battery is low and needs charging.
1 Connect the baby monitor (cont’d)
Charge the parent unit battery
When you have connected and turned on the parent unit, the battery will be charged
automatically.
NOTESNOTE
Notes
Before using the baby monitor for the first time, charge the parent unit battery for 12 hours. When
the parent unit battery is fully charged, the battery icon segments are solid .
It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time,
turn the parent unit off while charging.
The standby time varies depending on the sensitivity level you set, your actual use and the age of
the battery.
The battery icon indicates the battery status (see the following table).
Battery indicators Battery status Action
The screen displays .
The light flashes.
The battery has very little
charge and may be used for
only a short time.
Charge
without interruption
(about
30 minutes).
The battery icon segments
are solid .
The battery is fully charged. To keep the battery charged, connect
it to AC power when in use.
Specifications are subject to change without notice.
© 2023 VTech Communications, Inc. All rights reserved.
08/23. VM4263-X_QSG_US_V1.
Technical specications
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Baby unit: 2405 - 2475 MHz
Parent unit: 2405 - 2475 MHz
Channels 32
LCD 3.5” Color LCD
(QVGA 320x240 pixel)
Nominal effective range Maximum power allowed by FCC and IC. Actual operating range
may vary according to environmental conditions at the time of use.
Power requirements Parent unit: 3.6V, 2600mAh Li-ion, 9.36Wh Li-ion battery
Power adapter: Output: 5V DC @ 1A
UL STD.
62368-1
CERTIFIED TO
CSA STD.
CONFORMS TO
Main
menu Sub-menu
Volume
Volume
Adjust the Parent unit’s
speaker volume.
Settings
Screen off timer
The parent unit screen will
turn off after the selected
time to save energy. You can
still hear your baby while the
screen is turned off.
VOX (Voice Activated Alert)
Sensitivity
When VOX is selected,
the parent unit screen will
automatically turn on when
detected sounds exceed
a set level. You can adjust
the baby unit microphone
sensitivity level so that the
higher the sensitivity level,
the more sensitive the baby
unit is in detecting sounds
for transmitting to the parent
unit. For details, see the
Sound sensitivity and sound
activation section.
• The parent unit will then turn
off again after 50 seconds if
the sound detected is lower
than the set level.
NOTESNOTE
Note
When the parent unit screen
is off, if alerts are received, for
example, no signal received
between the parent unit and
baby unit, or a low battery, the
parent unit screen will turn on.
Main
menu Sub-menu
Settings
Brightness
Adjust the parent unit’s LCD
screen brightness level.
Zoom
Zoom in and out of the video
displayed from the baby unit.
Temperature
• Turn on/off temperature alert
tone.
• Set the parent unit to
beep whenever the room
temperature detected by the
baby unit falls outside of the set
temperature range.
Set the minimum/maximum
temperature.
• Set temperature display in
Fahrenheit (oF) or Celsius (oC).
Lullaby
Lullaby volume
• Adjusts the baby unit
speaker volume when
playing a lullaby.
Select between two lullabies or
two sounds to play or stop.
1
2
8
6
7
9
10
11
4
5
3
1
2
8
6
7
9
10
11
4
5
3
1
2
8
6
7
9
10
11
4
5
3
1 Night light key
2Light Sensor
3Camera lens
4Infrared LEDs
5Microphone
6Night light
7PAIR key
The parent unit and baby unit provid-
ed are already paired.
8Speaker
9Temperature sensor
10 Power jack
11 Slots for wall mounting
Press and hold
<1m
1m
Press and hold
Pan and Tilt the Baby Unit
Press Arrow keys | | | to pan and
tilt the Baby Unit.
1Antenna
2LINK LED light
On when the parent unit is linked to the
baby unit.
Flashes when the link to the baby unit has lost.
3 Battery LED light
43-level sound indicator light
5TALK/EXIT
Press and hold to talk to the baby unit.
While in a submenu, press to exit.
6POWER/LCD OFF
7 | | | Arrow keys
8MENU/SELECT
9/10 VOL+ / VOL-
11 Microphone
12 Power jack
13 RESET
Force reboot the parent unit.
14 Speaker
1
2
4
5
6
8
9
7
3
10
11
12
13
14
>3ft (1m) >3ft (1m)
<3ft (1m)
3ft (1m)
<3ft (1m)
Submenu
Main menu
Product Recycling
Recycle this product when you are done with it.
For more information, scan the QR code
or visit vtechphones.com/recycle.
Night vision
Mount the baby unit on dry wall (optional)
For VM4263-2 only
Sound sensitivity and sound activation
The RBRC seal on the Li-ion battery indicates that VTech Communications, Inc. is voluntarily participating in
an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of
service within the United States and Canada.
The program provides a convenient alternative to placing used Li-ion batteries into the trash or municipal
waste, which may be illegal in your area.
VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or
at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and
disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our
environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.
This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor
is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge
the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby
units, the CEC battery charging testing mode is activated while it is powered off and charging.
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the
Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed
by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with
the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of
approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your
face.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause
interference. (2) This device must accept any interference, including interference that may cause undesired operation of the
device.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were
met.
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
RF radiation exposure statement
The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should
be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect
to Canada’s Health Code 6 for Exposure of Humans to RF Fields.
The RBRC seal
California Energy Commission battery
charging testing mode
FCC and IC regulations
Dim mode
Parent unit icons (cont’d)
The baby unit has infrared LEDs that
allow you to see your baby clearly at
night or in a dark room. When the baby
unit detects low light levels, the infrared
LEDs are switched on automatically.
The images from the baby unit are in
black and white, and appears on the
screen.
Notes
It is normal to see a short white glare on
your parent unit screen when the baby
unit adapts to the dark environment.
When the infrared LEDs are on, the
images are in black and white. This is
normal.
Tip
Depending on the surroundings and other
interfering factors, for example, lighting,
objects, colours and backgrounds, the
image quality may vary. Adjust the baby
unit angle or place the baby unit at a
higher location to prevent glare and a
blurred display.
Dim mode helps you save parent unit power. Your parent unit display will automatically
dim after 10 minutes of inactivity, when no keys are pressed or alerts are received from the
baby unit.
10 min inactivity
Press any button
NOTESNOTE
Note
When the screen is dimmed, any keypress or alert message will trigger the screen to return to the
preset brightness level. After 10 minutes of inactivity, it will resume back to dim mode.
1. Press MENU when the parent unit is idle.
2. Press or to choose .
3. Press or to choose , then press SELECT to confirm your selection.
Change different views - Patrol
10s
1. Press MENU when the parent unit is idle.
2. Press or to choose .
3. Press or to choose between and , then press SELECT to confirm the baby unit
you would like to view.
Change different views - Single-cam
Frequently asked questions Disclaimer and Limitation of Liability
VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the
use of this user’s manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or
claims by third parties that may arise through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada
Warning icons and messages
Battery low at
Parent Unit
The battery is empty and
needs to be recharged.
Operation is in progress.
Temperature
too high
The temperature detected
by the baby unit is higher
than the maximum
temperature alert setting.
Temperature
too low
The temperature detected
by the baby unit is
lower than the minimum
temperature alert setting.
No Link to
Camera
The parent unit is searching
for baby units or the link
between the baby unit and
the parent unit has lost.
The parent unit is
connected to AC power.
LINK On when the parent unit is
linked to the baby unit.
Flashes when the link to the
baby unit being viewed has
lost.
On when the parent unit is
connected to AC power, or
the battery is charging.
Flashes when the parent unit
battery is low and needs
charging.
Off when the parent unit
is disconnected from AC
power.
Parent Unit Indication Lights
Mesures de sécurité importantes
La plaque signatique appliqe est située au bas du socle de
l’unité du bé.
Lorsque vous utilisez votre appareil, vous devriez toujours suivre
certaines mesures de précaution de base afin de réduire les
risques d’incendie, d’électrocution et de blessures corporelles,
dont ceux qui suivent :
1. Observez toutes les instructions et mises en garde inscrites sur
l’appareil.
2. L’installation par un adulte est requise.
3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur
supérieure à 2 mètres.
4. Ce produit ne remplace pas la surveillance adulte du nourrisson.
La supervision du nourrisson est la responsabilité du parent ou
de la personne qui s’occupe de l’enfant. Ce produit pourrait
cesser de fonctionner et, par conséquent, vous ne devriez
pas présumer qu’il continuera de fonctionner correctement
pendant une période de temps donnée. De plus, il ne s’agit pas
d’un instrument médical et ne devrait pas être utilisé comme tel.
Ce produit est destiné à vous aider à superviser votre bébé.
5. N’utilisez pas cet appareil près de l’eau ni de toute autre
source d’humidité, par exemple, près d’une baignoire, cuve
à lessive, évier de cuisine, dans un sous-sol humide ni près
d’une piscine, dans un soussol humide ou une douche.
6. MISE EN GARDE: N’utilisez que la pile fournie. Il peut y avoir
un risque d’explosion si un mauvais type de pile est utilisé
pour le dispositif apaisant. La pile ne peut pas être soumise
a des températures extrêmes élevées ou basses et a une
faible pression atmosphérique a haute altitude pendant
son utilisation, son entreposage ou son transport. Le fait de
jeter la pile dans au feu ou dans un four chaud, ou d’écraser
ou de couper mécaniquement la pile peut entrainer une
explosion. Le fait de laisser la pile dans un environnement
a température extrêmement élevée peut entrainer une
explosion ou une fuite de liquide ou de gaz inflammable. Une
pile soumise a une pression d’air extrêmement basse peut
provoquer une explosion ou une fuite de liquide ou de gaz
inflammable. Mettez au rebut la pile usagée conformément
aux informations figurant dans la section Le sceau RBRC.
7. N’utilisez que les adaptateurs inclus avec ce produit.
L’utilisation d’un adaptateur dont la polarité ou la tension serait
inadéquate risque d’endommager sérieusement le produit et
mettre votre sécurité en péril.
Informations sur les adaptateurs électriques :
Sortie : 5V DC 1A
VTech Telecommunications Ltd.
Modèle : VT05EUS05100
-OU-
Jiangxi Jian Aohai Technology Co., Ltd.
Modèle : A318-050100W-US2
Informations sur les piles rechargeables :
Zhuhai Great Power Energy Co., Ltd.
Li-ion battery, 3,6V, 2600mAh, 9,36Wh;
Model: ICR18650-2.6Ah-3.6V-1S1P
8. Lorsqu’ils sont branchés dans une prise de courant, les
adaptateurs secteur ont été conçus pour être orientés
correctement, soit à la verticale ou au plancher. Les broches
n’ont pas été conçues pour supporter le poids du bloc
d’alimentation et le maintenir en place si celuici est branché
dans une prise au plafond, sous une table ou dans un meuble.
9. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT,
la prise de courant doit être installée près du produit, afin
d’assurer une accessibilité sécuritaire à la prise de courant.
10. Débranchez ce produit de la prise de courant avant de
procéder au nettoyage. N’utilisez pas de nettoyants en
aérosols. Utilisez un chiffon humide pour le nettoyer.
11. Ne coupez pas les cordons d’alimentation pour remplacer les
fiches, car ceci peut présenter un danger potentiel.
12. Ne laissez aucun objet reposer ni appuyer sur le cordon
d’alimentation. N’installez pas cet appareil dans un endroit
où l’on risque d’écraser le cordon d’alimentation ou de le
piétiner.
13. Ne faites fonctionner cet appareil qu’avec le type
d’alimentation indiqué sur l’étiquette. Si vous ne connaissez
pas le type d’alimentation que vous possédez à votre
domicile, consultez votre marchand ou votre compagnie
locale d’électricité.
14. Ne surchargez pas les prises de courant murales ni les
rallonges électriques.
15. Ne placez pas cet appareil sur un chariot, meuble, trépied,
support de montage ni table chancelants.
16. Les trous et ouvertures du boîtier, situés à l’arrière de
l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour
l’empêcher de surchauffer, ne bloquez sous aucun prétexte
ces ouvertures et n’empêchez pas l’aération adéquate de
l’appareil en le plaçant sur un lit, divan, tapis ou toute autre
surface similaire. De même, ne le positionnez pas à proximité
ni au-dessus d’une source de chaleur ou d’un calorifère. De
plus, ne placez pas l’appareil dans un endroit avant de vous
assurer qu’il y ait une bonne circulation d’air.
17. N’enfoncez jamais d’objets à travers les ouvertures de
cet appareil, car ils pourraient entrer en contact avec
des points de tension dangereux ou causer des courts-
circuits qui peuvent dégénérer en incendies ou en risques
d’électrocution. Ne renversez jamais de liquide dans ce
produit.
18. Afin de réduire les risques d’électrocution, ne démontez
pas cet appareil, mais apportez-le dans un centre de service
autorisé. L’ouverture du boîtier ou le retrait de toutes pièces
que contient cet appareil, à l’exception de l’accès autorisé
à certaines portes ou ouvertures, risque de vous exposer à
des points de tension dangereux ou d’autres dangers. Un
remontage incorrect peut par la suite présenter des risques
d’électrocution.
19. Vous devriez tester la réception chaque fois que vous mettez
l’appareil en fonction.
20. Examinez les composantes afin de vérifier si celles-ci ne sont
pas endommagées.
21. Il existe un très faible risque de perte de confidentialité
avec certains appareils électroniques (autres écoute-bébés,
téléphones sans fils etc.). Pour l’éviter, s’assurer que le
produit n’a jamais été utilisé avant l’achat, réinitialiser l’unité
de façon périodique, éteindre l’écoute-bébé quand il n’est
pas en cours d’utilisation.
22. Les enfants devraient être supervisés afin de vous assurer
qu’ils ne jouent pas avec l’appareil.
23. Le produit n’est pas conçu pour être utilisé par des
personnes (incluant des enfants) aux capacités physiques,
sensorielles ou mentales réduites ou qui manquent
d’expérience et de connaissances, à moins qu’on leur
ait donné suffisamment de supervision ou d’instructions
relativement à l’utilisation de l’appareil par une personne
responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
1. Utilisez et entreposez le produit à une température entre
0 oC (32 oF) et 40 oC (104 oF).
2. N’exposez pas cet appareil à des froids ou des chaleurs
extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez
pas près d’une source de chauffage.
3. Le bloc-piles ne doit pas être exposé à la chaleur excessive
telle que la lumière du soleil ou au feu.
4. Avertissement - Risque de strangulation
- Les enfants se sont ÉTRANGLÉS dans des
cordons. Gardez ce cordon hors de portée des
enfants (à plus de 0,9 m). N’enlevez pas cette
étiquette.
5. Ne jamais placer le moniteur à l’intérieur du
berceau ou du parc de bébé. Ne jamais couvrir le moniteur
ou l’unité (s) portative avec un article tel une serviette ou une
couverture.
6. D’autres équipements électroniques peuvent produire des
interférences sur votre moniteur vidéo et audio. Tentez
d’installer votre moniteur vidéo ou audio à l’écart des appareils
électroniques tels que des routeurs sans fil, radios, téléphones
cellulaires, interphones, moniteurs, téléphones, ordinateurs
personnels, électroménagers et téléphones sans fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs
numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une
firme de recherche indépendante, a mené une évaluation
pluridisciplinaire des interférences entre les téléphones sans fil
portatifs et les stimulateurs cardiaques implantés dans l’organisme.
Appuyée par l’Administration des aliments et drogues (FDA) des
États-Unis, la firme WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
Vous devriez maintenir les dispositifs sans fil à au moins six
pouces du simulateur cardiaque.
Ils ne doivent PAS placer le téléphone sans fil directement sur
le stimulateur cardiaque, tel que dans une poche de chemise,
lorsque celui-ci est en marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque
pour les détenteurs de simulateurs cardiaques causés par les gens
qui utilisent dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes les normes se
rapportant aux champs électromagnétiques (EMF) standard. Si
vous le manipulez correctement en suivant les instructions de ce
guide, son utilisation sera sécuritaire pendant de nombreuses
années, selon les meilleures évidences scientifiques dont nous
disposons aujourd’hui.
For cETL compliance only
Main
menu Sub-menu
Night Light
Adaptive night light
• Turn on/off the night light’s
ability to automatically adjust its
brightness based on surrounding
lighting conditions.
Night light timer
• Set the timer to turn the night light
off.
When set to AUTO, the night
light turns on upon detecting
sound from the baby unit. It will
turn off after 15 minutes of no
sound detection. You can set VOX
sensitivity level to detect sounds
that exceed the set sensitivity
level. See Sound sensitivity and
sound activation section.
Night light color
• Select one of the seven colors or
choose number 8, the rainbow
color.
Night light On/Off
Turn on/off the night light.
Monitoring Mode (For VM4263-2 only)
Patrol mode
• Monitor your baby in PATROL
mode, where the screen will cycle
through display videos streamed
from all the linked baby units (For
VM4263-2 only).
• View the video from your
selected baby unit’s camera
(For VM4263-2 only).
Main menu icons
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the
holder of a valid proof of purchase (“Consumer” or “you”)
that the Product and all accessories provided in the sales
package (“Product”) are free from defects in material
and workmanship, pursuant to the following terms and
conditions, when installed and used normally and in
accordance with the Product operating instructions. This
limited warranty extends only to the Consumer for Products
purchased and used in the United States of America and
Canada.
What will VTech do if the Product is not free from defects
in materials and workmanship during the limited warranty
period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service
representative will replace at VTech’s option, without charge,
a Materially Defective Product. If we choose to replace
the Product, we may replace it with a new or refurbished
Product of the same or similar design. We will retain
defective parts, modules, or equipment. Replacement of the
Product, at VTech’s option, is your exclusive remedy. VTech
will return the replacement Products to you in working
condition. You should expect the replacement to take
approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE
(1) YEAR from the date of purchase (90 days on products
purchased as Refurbished*). This limited warranty also
applies to the replacement Product for a period of either (a)
90 days from the date the replacement Product is shipped
to you or (b) the time remaining on the original one-year
warranty (90-day limited warranty on products that are
purchased as Refurbished*); whichever is longer.
*Refurbished products purchased from our online store
carry a 90-day replacement warranty.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident,
shipping or other physical damage, improper installation,
abnormal operation or handling, neglect, inundation,
fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration
or modification by anyone other than an authorized
service representative of VTech; or
3. Product to the extent that the problem experienced is
caused by signal conditions, network reliability, or cable or
antenna systems; or
4. Product to the extent that the problem is caused by use
with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial
number plates or electronic serial numbers have been
removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair
from outside the United States of America or Canada, or
used for commercial or institutional purposes (including
but not limited to Products used for rental purposes); or
7. Product returned without a valid proof of purchase (see
item 2 below); or
8. Charges for installation or set up, adjustment of customer
controls, and installation or repair of systems outside the
unit.
How do you get warranty service?
To obtain warranty service in the USA, please visit our
website at www.vtechphones.com or call 1 (800) 595-9511.
In Canada, go to www.vtechcanada.com or call
1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s
manual - a check of the Product’s controls and features may
save you a service call.
Except as provided by applicable law, you assume the risk
of loss or damage during transit and transportation and are
responsible for delivery or handling charges incurred in the
transport of the Product(s) to the service location. VTech
will return replaced Product under this limited warranty.
Transportation, delivery or handling charges are prepaid.
VTech assumes no risk for damage or loss of the Product in
transit.
What must you return with the Product to get warranty
service?
1. Return the entire original package and contents including
the Product to the VTech service location along with a
description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt)
identifying the Product purchased (Product model) and
the date of purchase or receipt; and
3. Provide your name, complete and correct mailing
address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement
between you and VTech. It supersedes all other written or
oral communications related to this Product. VTech provides
no other warranties for this Product. The warranty exclusively
describes all of VTech’s responsibilities regarding the
Product. There are no other express warranties. No one is
authorized to make modifications to this limited warranty and
you should not rely on any such modification. State/Provincial
Law Rights: This warranty gives you specific legal rights, and
you may also have other rights, which vary from state to state
or province to province.
Limitations: Implied warranties, including those of fitness
for a particular purpose and merchantability (an unwritten
warranty that the Product is fit for ordinary use) are limited
to one year from the date of purchase. Some states/
provinces do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
In no event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages (including,
but not limited to lost profits or revenue, inability to use
the Product or other associated equipment, the cost of
substitute equipment, and claims by third parties) resulting
from the use of this Product. Some states/provinces
do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion
may not apply to you.
Please retain your original sales receipt as proof
of purchase.
Limited warranty
When VOX is selected, the parent unit screen stays off to save power when the baby unit detects
sounds that are lower than the set sensitivity level. Once the baby unit detects sounds that are
louder than the set sensitivity level, the parent unit screen turns on automatically. It will then turn
off again after 50 seconds if the sounds detected are lower than the set sensitivity level.
Adjust the sound sensitivity of the baby unit
The parent unit screen will turn on only when the detected
sounds exceed a set level.
Use the parent unit to adjust the microphone sensitivity of
your baby unit. The higher the sensitivity level, the more
sensitive the baby unit is in detecting sounds that transmit
to the parent unit. The VOX sensitivity level is preset to the
highest level.
VOX
Sensitivity
level Highest High Medium Low Lowest
Description The parent
unit screen
turns on
for quiet
sounds,
(including
background
noises) from
your baby’s
room.
The parent
unit screen
turns on
for soft
babbling
and louder
sounds from
your baby. It
remains off
when your
baby sleeps
soundly.
The parent
unit screen
turns on
for loud
babbling
and louder
sounds from
your baby. It
remains off
when your
baby makes
soft sounds.
The parent
unit screen
turns on
for crying
and louder
sounds from
your baby. It
remains off
when your
baby makes
soft sounds.
The parent
unit screen
turns on
for loud
crying or
screeching
sounds from
your baby. It
remains off
when your
baby makes
soft sounds.
Below are the questions most frequently asked about the baby monitor.
Why does the
baby monitor
not respond
normally?
Try the following (in the order listed) for common cure:
1. Disconnect the power to the baby units and the parent unit.
2. Wait a few seconds before connecting power back to the baby units and the parent unit.
3. Turn on the baby units and the parent unit.
4. Wait for the parent unit to synchronize with the baby units. Allow up to one minute
for this to take place.
Why doesn’t the
baby unit and parent
unit power-on light
illuminate when the units
are switched on?
Perhaps the parent unit is not connected to the power. Insert the adapter plug into
the parent unit and insert the adapter in a wall socket. Then, press and hold POWER to
switch on the parent unit to establish connection with the baby unit.
Perhaps the baby unit is not connected to the power. Insert the adapter plug into the
baby unit and insert the adapter in a wall socket. Then, establish a connection with the
parent unit.
Why doesn’t my parent
unit charge while
connected to AC power?
Make sure the power is not controlled by electronic wall switch.
The battery may de degraded through extended use or defective. See Warranty for
repair/replacement.
Why is my screen in
black and white?
The screen is in black and white during night-time or in a dark room when the night
vision feature is activated. This is normal.
Why do I get glare or
blurry display on my
screen when viewing my
baby at night?
During night-time or in a dark room, the surroundings and other interfering factors,
like lighting, objects, colors and backgrounds may affect the image quality on your
parent unit screen. Adjust the baby unit angle or place the baby unit at a higher level to
prevent glare and a blurry display.
Why does the baby
monitor produce a
feedback noise?
The parent unit and baby units may be too close to each other.
Move the parent unit away from the baby units until the noise stops; OR
Turn down the volume of your parent unit.
Why does the parent
unit beep?
The baby units may be out of range. Move the parent unit closer to the baby units (but
not less than 3 feet (1 meter)).
The parent unit may not have enough charge for the parent unit to perform normally.
Charge the battery in the parent unit until the battery icon segments are solid .
The temperature of your baby’s room may be too high or too low.
Why does the parent
unit react too quickly to
other sounds?
The baby unit also picks up other sounds than those of your baby. Adjust the VOX
sensitivity level to a lower level or lower the parent unit speaker volume.
Why don’t I hear a
sound/Why can’t I hear
my baby cry?
The parent unit speaker volume may be too low. See Adjust parent unit speaker
volume to increase the volume.
Why can’t I establish a
connection? Why is the
connection lost every now
and then? Why are there
sound interruptions?
The baby units may be out of range. Move the parent unit closer to the baby units (but
not less than 3 feet (1 meter)).
Other electronic products and wireless products may cause interference with your
baby monitor. Try installing your baby monitor as far away from these devices as
possible.
If you power on only one baby unit, your parent unit may display , and the LINK
LED light will flash.
CABLE MANAGEMENT
1 2 3
Use a pencil to mark two holes in parallel.
Make sure they are the same distance apart
as the wall mount holes on the baby unit.
NOTESNOTE
Note
Check for reception strength and camera
angle before drilling the holes.
Not Included
You will need to purchase the following
items separately to mount your baby unit:
2 screws 2 anchors
Adjust the camera angle.
Drill two holes in the wall ( 5.5 mm drill bit ). If
you drill the holes into a stud, go to step 3.
-OR-
If you drill the holes into an object other than
a stud, insert the anchors into the holes. Tap
gently on the ends with a hammer until the
anchors are flush with the wall.
Insert the screws into the holes and
tighten the screws until only 6.5 mm of
the screws are exposed.
Align the wall mount holes on the
baby unit with the screws on the wall.
Slide the baby unit down until it locks
into place.
NOTESNOTE
Note
The types of screws and anchors you need
depend on the composition of the wall.
  • Page 1 1
  • Page 2 2

VTech VM4263 Guide de démarrage rapide

Catégorie
Moniteurs vidéo bébé
Taper
Guide de démarrage rapide

dans d''autres langues