INSTALLATION
INSTRUCTIONS
Indoor Hearth Oven
ZEP30FR
ENGLISH / FRANÇAIS./ ESPAÑOL.
MONOGRAM.COM
231-2001053 Rev. 1
Safety Information
READ AND SAVE THESE INSTRUCTIONS
FOR YOUR SAFETY
• Be sure your oven is installed properly by a qualified
installer or service technician.
• Be sure the oven is securely installed in a cabinet that
is firmly attached to the house structure. Never allow
anyone to climb, sit, stand or hang on the oven.
• Make sure the cabinets and wall coverings around
the oven can withstand the temperatures (up to
200°F [93.3°C]) generated by the oven.
WARNING The electrical power to the
oven supply line must be shut off while line
connections are being made. Failure to do so
could result in serious injury or death.
ELECTRICAL REQUIREMENTS
Rating plate is located on the top right of the front
panel.
We recommend you have the electrical wiring
and hookup of your oven connected by a qualified
electrician. After installation, have the electrician show
you how to disconnect power from the range.
ELECTRICAL REQUIREMENTS
This appliance must be supplied with the proper
voltage and frequency, and connected to an individual,
properly grounded branch circuit, protected by a circuit
breaker or fuse. See the rating plate located on the
bottom of the front panel to determine the rating of
the product. The chart below shows the minimum
recommended dedicated circuit protection.
KW Rating 240V KW Rating 208V Required Circuit
Size (Dedicated)
9.7 KW–12.0 KW 8.4 KW–10.4 KW 50 Amp
Rating Plate Location
Have a question or need assistance with your appliance? Try the Monogram website 24 hours a day, any day of the year!
You can also shop for more great Monogram products and take advantage of all our on-line support services designed for
your convenience. In the US: monogram.com or call 800.444.1845.
WARNING Installations with Aluminum House
Wiring require attention:
• Improper connection of Aluminum house wiring
to appliance copper leads can result in an
electrical hazard or fire. Use only connectors
designed for joining copper to aluminum
and follow the manufacturer’s recommend
procedure closely.
• Aluminum to Copper wiring connections must
conform with the National Electrical code, local
codes and industry-accepted wiring practices.
• If an anti-oxidant compound is added to the
wiring connectors, the compound should
be UL-Listed and suitable for the application
materials, voltage and temperature.
• Connectors for joining Aluminum and Copper
wiring may be larger in size than standard
connectors. It is recommended to use a
double-gang, or larger, electrical box to enclose
the connectors joining Aluminum and Copper
wiring.
ELECTRICAL REQUIREMENTS (Cont.)
Check with your local utilities for electrical codes
which apply in your area. Failure to wire your oven
according to governing codes could result in a
hazardous condition. If there are no local codes,
your oven must be wired and fused to meet the
requirements of the National Electrical Code, NFPA
No. 70–Latest Edition, available from the National Fire
Protection Association.
Effective January 1, 1996, the National Electrical
Code requires that new, but not existing, construction
utilize a four-conductor connection to an electric oven.
When installing an electric oven in new construction,
a mobile home, recreational vehicle or an area where
local codes prohibit grounding through the neutral
conductor, follow the instructions in the section on
NEW CONSTRUCTION AND FOUR-CONDUCTOR
BRANCH CIRCUIT CONNECTION.
You must use a single-phase 120/208 VAC or 120/240
VAC, 60 hertz electrical system. If you connect
to aluminum wiring, properly installed connectors
approved for use with aluminum wiring must be used.
31-2001053 Rev. 1 3
Contents
CONTENTS
Safety Information .......................................................2
Design Information
Product Dimensions (With Trim) ...................................4
Pre-Installation Checklist ...............................................5
Installation Information
Parts Included ...............................................................6
Materials Needed (not provided) ...................................6
Tools Needed ................................................................6
Installation
1A: Cutout for Hearth Oven - Standard Installation ......7
1B: Hearth Oven - Flush Inset Installation ....................8
1C: Hearth Oven Over Wall Oven –Standard Installation
With A Minimum Gap Between ..............................9
1D: Hearth Oven Over Wall Oven – Flush-Inset
Installation With A Minimum Gap Between ..........10
1E: Hearth Oven Over Wall Oven –Standard Installation
With A 2” Platform Between .................................11
1F: Hearth Oven Over Wall Oven – Flush Inset
Installation With A 2” Platform Between ...............12
1G: Hearth Oven Over French Door Wall Oven –
Standard Installation With A Minimum Gap
Between ...............................................................13
1H: Hearth Oven Over French Door Wall Oven –
Standard Installation With A 2” Platform
Between ................................................................14
1I: Hearth Oven Over Steam Oven –Standard
Installation With A Minimum Gap Between............15
1J: Hearth Oven Over Steam Oven – Flush-Inset
Installation With A Minimum Gap Between...........16
1K: Hearth Oven Over Steam Oven –Standard
Installation With A 2” Platform Between ...............17
1L: Hearth Oven Over Steam Oven – Flush-Inset
Installation With A 2” Platform Between ...............18
1M: Hearth Oven Over Warming Drawer –Standard
Installation With A Minimum Gap Between..........19
1N: Hearth Oven Over Warming Drawer – Flush-Inset
Installation With A Minimum Gap Between ..........20
1O: Hearth Oven Over Warming Drawer –Standard
Installation With A 2” Platform Between...............21
1P: Hearth Oven Over Warming Drawer – Flush-Inset
Installation With A 2” Platform Between ...............22
1Q: Hearth Oven Platform For Minimum Gap Between
Appliances: Dado & Mechanical Fastener
Concept ................................................................ 23
1R: Hearth Oven Platform For Minimum Gap Between
Appliances: Tenon & Mechanical Fastener
Concept ................................................................24
1S: Side-By-Side Combo Installation ..........................25
2. Electrical Connections .............................................26
3. Installing the Oven in the Cabinet ...........................28
PRE-TEST CHECKLIST ............................................. 29
OPERATION CHECKLIST .........................................29
431-2001053 Rev. 1
Design Information
PRODUCT DIMENSIONS (WITH TRIM)
29 3
4"
Overall At Front
1
8"
Trim Offset
Foot To
Bottom Trim
31
4"
Upper Trim
Height
19 5
16 "
Front Height
11
32 "
Foot to
Front Bottom
25 27
32 "
Outside Feet Overall
24 1
2"
Overall Front
To Back Spacer
1
8"
Trim Offset
1
8"
Trim Offset
23 9
16 "
Foot To Top Trim
11
8"
Offset To Spacer
11
16 "
Foot To Case Bottom
321
32 "
Case Top
To Spacer
28 3
8"
Case Width
At Side Spacers
1"
Front Depth
23 1
2"
Back Of Top Trim
To Back Spacer
31-2001053 Rev. 1 5
Design Information
PRE-INSTALLATION CHECKLIST
ALL INSTALLATION INFORMATION ON
THE FOLLOWING PAGES IS TO BE USED
FOR ELECTRIC INDOOR HEARTH OVEN
INSTALLATION!
Remove packaging materials and literature pack.
Remove Installation Instructions from literature pack
and read them carefully before you begin.
Be sure to place all literature, Owner’s Manual,
Installations, etc. in a safe place for future reference.
Place the oven on a table or platform even
with the cutout opening. Platform must support
200 lbs. (91 Kg).
The Hearth Oven may be installed in a cabinet
alone, above or next to approved models. See label
on top of the oven for approved models or go to
geappliances.com/combinations.
CAUTION
Installing the oven below the
minimum height of 45 inches creates a burn
hazard for children. Do not install below the
minimum height.
Literature Pack
Included Trim
Hearth Oven
Before you begin-R
ead thes
e ins
tructions completely and carefully.
IMPORTANT- Save thes
e ins
tructions
for loca l inspector's
use.
IMPORTANT- OB
SER
VE ALL GOVERNING CODES AND ORDIANCE
S.
Note to Installer- B
e sure to leave these instructions
with the consumer.
OWNER- Keep thes
e instructions for future reference.
Note- This appliance must be properly grounded (if applicable).
Before you begin-Read these
ins
tructions
completely and
carefully.
IMPORTANT- Save these
instructions
for local inspector's
use.
IMPORTANT- OBS
ERVE ALL
GOVE
RNING CODES AND OR
DIANCES.
Note to Installer- B
e s
ure to leave
these instructions with the consumer.
OWNER
- Keep thes
e instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
FOR YOUR
S
AFETY
Before you begin-Read thes
e ins
tructions completely and carefully.
IMPORTANT- Save these ins
tructions
for local insp ector's use.
IMPORTANT- OB
SER
VE ALL GOVE
RNING CODES AND OR
DIANC
E
S.
Note to Installer- B
e sure to leave these instructions
with the consumer.
OWNER- Keep these instructions for future reference.
Note- This
appliance must be properly grounded (if applicab le).
Before you begin-Read thes
e ins
tructions completely and carefully.
IMPORTANT- Save these instructions
for local ins
pector's
use.
IMPORTANT- OB
SERVE ALL GOVERNING CODES AND ORDIANCES.
Note to Inst al ler- B
e sure to leave these instructions
with the consumer.
OWNER- Keep thes
e instructions for future reference.
Note- This
appliance must be properly grounded (if applicable).
ELECTRICAL REQUIR
EMENTS
B
efore you begin-Read these
ins
tructions completely and
carefully.
IMPORTANT- S
ave these
instructions for local ins
pector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODE
S AND ORDIANCE
S.
Note to Installer- Be sure to leave
these instructions with the cons
umer.
OWNE
R- Keep thes
e instructions
for future reference.
Note- This appliance must be
properly grounded (if applica ble).
B
efore you begin-Read these
instructions completely and
carefully.
IMPOR
TANT- Save thes
e
instructions for local inspector's use.
IMPORTANT- OB
SERVE
ALL
GOVERNING CODES AND ORDIANCES.
Note to Inst aller- Be sure t o leave
these instructions
with the consumer.
OWNER
- K
eep thes
e ins
tructions
for future reference.
Note- This
appliance must be
properly grounded (if applicable).
B
efore you begin-Read thes
e
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's
use.
IMPORTANT- OBSERV E ALL
GOVERNING CODE
S AND OR
DIANCES.
Note to Ins
taller- B
e sure to leave
these instructions
with the consumer.
OWNER- K
eep thes
e ins
tructions
for future reference.
Note- This
appliance must be
properly grounded (if applicable).
Before you begin-Read thes
e instructions completely and carefully.
IMPORTANT- Save these instructions
for local ins
pector's
use.
IMPORTANT- OB
SERVE ALL GOVE
RNING CODES AND OR
DIANCES.
Note to Installer- B
e sure to leave these instructions
with the consumer.
OWNER- Keep thes
e instructions for future reference.
Note- This
appliance must be properly grounded (if applicable).
Before you begin-Read these
ins
tructions
completely and
carefully.
IMPORTANT- Save these
instructions
for local inspector's
use.
IMPORTANT- OBS
ERVE ALL
GOVE
RNING CODES AND OR
DIANCES.
Note to Installer- B
e s
ure to leave
these instructions with the consumer.
OWNER
- Keep thes
e instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
FOR YOUR
S
AFETY
Before you begin-Read thes
e ins
tructions completely and carefully.
IMPORTANT- Save these ins
tructions
for local insp ector's use.
IMPORTANT- OB
SER
VE ALL GOVE
RNING CODES AND OR
DIANC
E
S.
Note to Installer- B
e sure to leave these instructions
with the consumer.
OWNER- Keep these instructions for future reference.
Note- This
appliance must be properly grounded (if applicab le).
Before you begin-Read thes
e ins
tructions completely and carefully.
IMPORTANT- Save these instructions
for local ins
pector's
use.
IMPORTANT- OB
SERVE ALL GOVERNING CODES AND ORDIANCES.
Note to Inst al ler- B
e sure to leave these instructions
with the consumer.
OWNER- Keep thes
e instructions for future reference.
Note- This
appliance must be properly grounded (if applicable).
ELECTRICAL REQUIR
EMENTS
B
efore you begin-Read these
ins
tructions completely and
carefully.
IMPORTANT- S
ave these
instructions for local ins
pector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODE
S AND ORDIANCE
S.
Note to Installer- Be sure to leave
these instructions with the cons
umer.
OWNE
R- Keep thes
e instructions
for future reference.
Note- This appliance must be
properly grounded (if applica ble).
B
efore you begin-Read these
instructions completely and
carefully.
IMPOR
TANT- Save thes
e
instructions for local inspector's use.
IMPORTANT- OB
SERVE
ALL
GOVERNING CODES AND ORDIANCES.
Note to Inst aller- Be sure t o leave
these instructions
with the consumer.
OWNER
- K
eep thes
e ins
tructions
for future reference.
Note- This
appliance must be
properly grounded (if applicable).
B
efore you begin-Read thes
e
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's
use.
IMPORTANT- OBSERV E ALL
GOVERNING CODE
S AND OR
DIANCES.
Note to Ins
taller- B
e sure to leave
these instructions
with the consumer.
OWNER- K
eep thes
e ins
tructions
for future reference.
Note- This
appliance must be
properly grounded (if applicable).
Before you begin-Read thes
e instructions completely and carefully.
IMPORTANT- Save these instructions
for local ins
pector's
use.
IMPORTANT- OB
SERVE ALL GOVE
RNING CODES AND OR
DIANCES.
Note to Installer- B
e sure to leave these instructions
with the consumer.
OWNER- Keep thes
e instructions for future reference.
Note- This
appliance must be properly grounded (if applicable).
Before you begin-Read these
ins
tructions
completely and
carefully.
IMPORTANT- Save these
instructions
for local inspector's
use.
IMPORTANT- OBS
ERVE ALL
GOVE
RNING CODES AND OR
DIANCES.
Note to Installer- B
e s
ure to leave
these instructions with the consumer.
OWNER
- Keep thes
e instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
FOR YOUR
S
AFETY
Before you begin-Read thes
e ins
tructions completely and carefully.
IMPORTANT- Save these ins
tructions
for local insp ector's use.
IMPORTANT- OB
SER
VE ALL GOVE
RNING CODES AND OR
DIANC
E
S.
Note to Installer- B
e sure to leave these instructions
with the consumer.
OWNER- Keep these instructions for future reference.
Note- This
appliance must be properly grounded (if applicab le).
Before you begin-Read thes
e ins
tructions completely and carefully.
IMPORTANT- Save these instructions
for local ins
pector's
use.
IMPORTANT- OB
SERVE ALL GOVERNING CODES AND ORDIANCES.
Note to Inst al ler- B
e sure to leave these instructions
with the consumer.
OWNER- Keep thes
e instructions for future reference.
Note- This
appliance must be properly grounded (if applicable).
ELECTRICAL REQUIR
EMENTS
B
efore you begin-Read these
ins
tructions completely and
carefully.
IMPORTANT- S
ave these
instructions for local ins
pector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODE
S AND ORDIANCE
S.
Note to Installer- Be sure to leave
these instructions with the cons
umer.
OWNE
R- Keep thes
e instructions
for future reference.
Note- This appliance must be
properly grounded (if applica ble).
B
efore you begin-Read these
instructions completely and
carefully.
IMPOR
TANT- Save thes
e
instructions for local inspector's use.
IMPORTANT- OB
SERVE
ALL
GOVERNING CODES AND ORDIANCES.
Note to Inst aller- Be sure t o leave
these instructions
with the consumer.
OWNER
- K
eep thes
e ins
tructions
for future reference.
Note- This
appliance must be
properly grounded (if applicable).
B
efore you begin-Read thes
e
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's
use.
IMPORTANT- OBSERV E ALL
GOVERNING CODE
S AND OR
DIANCES.
Note to Ins
taller- B
e sure to leave
these instructions
with the consumer.
OWNER- K
eep thes
e ins
tructions
for future reference.
Note- This
appliance must be
properly grounded (if applicable).
Before you begin-R
ead thes
e ins
tructions completely and carefully.
IMPORTANT- Save thes
e ins
tructions
for loca l inspector's
use.
IMPORTANT- OB
SER
VE ALL GOVERNING CODES AND ORDIANCE
S.
Note to Installer- B
e sure to leave these instructions
with the consumer.
OWNER- Keep thes
e instructions for future reference.
Note- This appliance must be properly grounded (if applicable).
Before you begin-Read these
ins
tructions
completely and
carefully.
IMPORTANT- Save these
instructions
for local inspector's
use.
IMPORTANT- OBS
ERVE ALL
GOVE
RNING CODES AND OR
DIANCES.
Note to Installer- B
e s
ure to leave
these instructions with the consumer.
OWNER
- Keep thes
e instructions
for future reference.
Note- This appliance must be
properly grounded (if applicable).
FOR YOUR
S
AFETY
Before you begin-Read thes
e ins
tructions completely and carefully.
IMPORTANT- Save these ins
tructions
for local insp ector's use.
IMPORTANT- OB
SER
VE ALL GOVE
RNING CODES AND OR
DIANC
E
S.
Note to Installer- B
e sure to leave these instructions
with the consumer.
OWNER- Keep these instructions for future reference.
Note- This
appliance must be properly grounded (if applicab le).
Before you begin-Read thes
e ins
tructions completely and carefully.
IMPORTANT- Save these instructions
for local ins
pector's
use.
IMPORTANT- OB
SERVE ALL GOVERNING CODES AND ORDIANCES.
Note to Inst al ler- B
e sure to leave these instructions
with the consumer.
OWNER- Keep thes
e instructions for future reference.
Note- This
appliance must be properly grounded (if applicable).
ELECTRICAL REQUIR
EMENTS
B
efore you begin-Read these
ins
tructions completely and
carefully.
IMPORTANT- S
ave these
instructions for local ins
pector's use.
IMPORTANT- OBSERVE ALL
GOVERNING CODE
S AND ORDIANCE
S.
Note to Installer- Be sure to leave
these instructions with the cons
umer.
OWNE
R- Keep thes
e instructions
for future reference.
Note- This appliance must be
properly grounded (if applica ble).
B
efore you begin-Read these
instructions completely and
carefully.
IMPOR
TANT- Save thes
e
instructions for local inspector's use.
IMPORTANT- OB
SERVE
ALL
GOVERNING CODES AND ORDIANCES.
Note to Inst aller- Be sure t o leave
these instructions
with the consumer.
OWNER
- K
eep thes
e ins
tructions
for future reference.
Note- This
appliance must be
properly grounded (if applicable).
B
efore you begin-Read thes
e
instructions completely and
carefully.
IMPORTANT- Save these
instructions for local inspector's
use.
IMPORTANT- OBSERV E ALL
GOVERNING CODE
S AND OR
DIANCES.
Note to Ins
taller- B
e sure to leave
these instructions
with the consumer.
OWNER- K
eep thes
e ins
tructions
for future reference.
Note- This
appliance must be
properly grounded (if applicable).
Installation
Instructions
BEFORE YOU BEGIN
Read these instructions carefully and completely.
•
IMPORTANT — Save these instructions
for local inspector’s use.
• IMPORTANT — Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the consumer.
• Note to Consumer – Keep these instructions for
future reference.
• Proper installation is the responsibility of the
installer and product failure due to improper
installation is NOT covered under warranty.
• Note – This appliance must be properly grounded.
• ATTENTION INSTALLER
All electric wall ovens must be hard wired (direct
wired) into an approved junction box. A plug and
receptacle is NOT permitted on these products.
Indoor Hearth Oven
ZEP30
MATERIALS NEEDED
TOOLS NEEDED
TRIM KIT PARTS
(Included with ZEP30F)
PARTS INCLUDED
(Appearance will vary)
If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737)
or visit our website at: GEAppliances.com.
31-11062 Rev. 3 03-19 GEA
Strain Relief Clamp
for 1/2” conduit
Plaster Ring
(Option 1)
Wire Strippers
3/4” Phillips
Screws (4)
Side Trim
Junction Box
(1 1/2 Depth Max.)
Phillips #2
Screwdriver
Flathead
Screwdriver
Drill and 3/32” drill bit
Wire Nuts
Brush
Option 1
Option 2
Metal Peel
Wooden Peel
1” Drywall Screw
5/8” Phillips
Case Screw
Tether
Top Grille
Bottom Grille
631-2001053 Rev. 1
Installation Information
BEFORE YOU BEGIN
Read these instructions carefully and completely.
• IMPORTANT — Save these instructions
for local inspector’s use.
• IMPORTANT — Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the consumer.
• Note to Consumer – Keep these instructions for
future reference.
• Proper installation is the responsibility of the installer
and product failure due to improper installation is
NOT covered under warranty.
• Note – This appliance must be properly grounded.
• ATTENTION INSTALLER
All electric wall ovens must be hard wired (direct
wired) into an approved junction box. A plug and
receptacle is NOT permitted on these products.
PARTS INCLUDED
(Appearance will vary)
Brush
Metal Peel
Top Grille
Assembly
Bottom
Grille
Wooden Peel
Upper &
Lower Grille
1/2” T20 Torx
(8)
3/4” Phillips
Screws (2)
MATERIALS NEEDED
TOOLS NEEDED
Strain Relief Clamp
for 1/2” conduit
Plaster Ring and Cover
(Option 1)
Wire Strippers
Junction Box
(1 1/2 Depth Max.)
Phillips #2
Screwdriver
Flathead
Screwdriver
T20 Torx Screwdriver Drill and 3/32” drill bit
Wire Nuts
Option 1 Option 2
31-2001053 Rev. 1 7
Installations
1 A HEARTH OVEN - STANDARD INSTALLATION
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Platform must be able to support 200 lbs (91 kg).
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 23-1/2” cabinet
depth. Junction box may also be located in an
adjacent cabinet.
E A flush appearance my be achieved relative to
surrounding cabinet door and drawer fronts. A
minimum 1/8” reveal BEYOND the OVERLAP
dimensions is recommended.
ELEC
10"
41
2"
11
16 "
OVERLAP
11
16 "
OVERLAP
11
16 "
OVERLAP
45"
MINIMUM FLOOR
TO OVEN PLATFORM
A
ASECTION A-A
28 1
2"
CUTOUT WIDTH
NO BOTTOM
OVEN OVERLAP
22 9
16 "23 1
2"
CABINET DEPTH
SEE NOTE D
831-2001053 Rev. 1
Installations
1 B HEARTH OVEN - FLUSH INSET INSTALLATION
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Platform must be able to support 200 lbs (91 kg).
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 24-15/16”
cabinet depth. Junction box may also be located in
an adjacent cabinet.
ELEC
B
BSECTION B-B
10"
41
2"
45"
MINIMUM FLOOR
TO OVEN PLATFORM
30"
CUT OUT WIDTH
11
8"
CLEAT
3
4"
CLEAT
3
4"
CLEAT 23 11
16 "
CUT OUT HEIGHT
24 15
16 "
CABINET DEPTH
7
8"
CLEAT SETBACK
21
2"
CLEAT DEPTH
SEE NOTE D
31-2001053 Rev. 1 9
Installations
1 C HEARTH OVEN OVER WALL OVEN –STANDARD INSTALLATION WITH A
MINIMUM GAP BETWEEN
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Hearth Oven Platform must be able to support
200 lbs. (91kg). For this installation, it is highly
recommended to lock the platform into the side
walls using wood joinery such as a Dado Joint.
Fasteners and wood glue are also encouraged to
further reinforce the locking wood joinery. The wood
grain of the platform shall be oriented left to right.
The front nose of the platform shall be a finished
appearance surface. See illustrations 1Q & 1R for
joinery concepts.
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 23-1/2”cabinet
depth. Junction box may also be located in an
adjacent cabinet.
E A minimum 1/8” reveal BEYOND the OVERLAP
dimensions is recommended for proper drawer and
door operating clearance.
F Exterior cleats may be added to the sides and top
of the Hearth Oven opening in order to bring the
front surface of the Hearth Oven into alignment with
the front surface of the wall oven below. Finish per
customer requirements. A flat black finish may better
match the side appearance of the oven below.
G For the LOWER WALL OVEN, an extruded
aluminum LOWER VENT TRIM is encouraged. Wall
oven models beginning with “ZTSX” already include
the aluminum vent trim. For models beginning
with “ZTS”, the vent trim kit ZX30VT1 must be
ordered which includes the aluminum vent trim and
mounting hardware. Alternatively, the stainless-steel
trim supplied with all models may be used in this
cabinet configuration. Be sure to adjust the “overlap”
dimension associated with the stainless-steel trim.
Please call 1-800-626-2000 with any questions.
H The opening center line dimension is taken at the
FRONT OPENING of each enclosure.
ELEC
ELEC
HEARTH OVEN PLATFORM
SEE NOTE B
10"
41
2"
91
2"
51
4"
11
16 "
OVERLAP
11
16 "
OVERLAP
11
16 "
OVERLAP
3
16 "
OVERLAP
SEE NOTE G
A
ASECTION A-A
25 13/16" MIN.
C
LTO C
L
SEE NOTE H
28 1
2"
CUTOUT WIDTH
28 1
2"
CUTOUT WIDTH
45" MIN.
7
8"
SEE NOTE F
1
2"
SEE NOTE F
1
2"
SEE NOTE F
22 9
16 "
27 5
8"
23 1
2"
CABINET DEPTH
23
32 "MIN.
"3/4 PLYWOOD"
7
16 "
SEE NOTE F
10 31-2001053 Rev. 1
Installations
1 D HEARTH OVEN OVER WALL OVEN – FLUSH-INSET INSTALLATION WITH A
MINIMUM GAP BETWEEN
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Hearth Oven Platform must be able to support
200 lbs. (91kg). For this installation, it is highly
recommended to lock the platform into the side
walls using wood joinery such as a Dado Joint.
Fasteners and wood glue are also encouraged to
further reinforce the locking wood joinery. The wood
grain of the platform shall be oriented left to right.
The front nose of the platform shall be a finished
appearance surface. See illustrations 1Q & 1R for
joinery concepts.
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 24-15/16”
cabinet depth. Junction box may also be located in
an adjacent cabinet.
E The front surface of the interior cleats shall be a
finished appearance surface.
F The Wall Oven REQUIRES an extruded aluminum
LOWER VENT TRIM. Wall oven models beginning
with “ZTSX” already include the aluminum vent
trim. For models beginning with “ZTS”, the vent trim
kit ZX30VT1 must be ordered which includes the
aluminum vent trim and mounting hardware.
Please call 1-800-626-2000 with any questions.
G The opening center line dimension is taken at the
FRONT OPENING of each enclosure.
H Wall Oven bottom surface cleat is to be ¼” thick
MDF fiber board or equivalent.
26 1
2"MIN.
C
LTO C
L
SEE NOTE G
ELEC.
SEE NOTE D
ELEC.
SEE NOTE D
HEARTH OVEN PLATFORM
SEE NOTE B
10"
41
2"
91
2"
51
4"
11
8"
CLEAT
3
4"
CLEAT
3
4"
CLEAT
30"
CUTOUT WIDTH
30"
CUTOUT WIDTH 45"
MIN
24 15
16 "
CABINET DEPTH
7
8"
HEARTH OVEN
CLEAT SETBACK
21
2"
CLEAT
DEPTH
17
16 "
WALL OVEN
CLEAT SETBACK
23
32 " Min.
"3/4 PLYWOOD"
1
4"
MDF
SEE NOTE H
23 11
16 "
27 7
8"
SECTION A-A
A
A
31-2001053 Rev. 1 11
Installations
1 E HEARTH OVEN OVER WALL OVEN –STANDARD INSTALLATION WITH A 2”
PLATFORM BETWEEN
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Hearth Oven Platform must be able to support
200 lbs. (91kg).
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 23-1/2” cabinet
depth. Junction box may also be located in an
adjacent cabinet.
E A minimum 1/8” reveal BEYOND the OVERLAP
dimensions is recommended for proper drawer and
door operating clearance.
F Exterior cleats may be added to the sides and top
of the Hearth Oven opening in order to bring the
front surface of the Hearth Oven into alignment with
the front surface of the wall oven below. Finish per
customer requirements. A flat black finish may better
match the side appearance of the oven below.
G For the LOWER WALL OVEN, an extruded
aluminum LOWER VENT TRIM is encouraged. Wall
oven models beginning with “ZTSX” already include
the aluminum vent trim. For models beginning
with “ZTS”, the vent trim kit ZX30VT1 must be
ordered which includes the aluminum vent trim and
mounting hardware. Alternatively, the stainless-steel
trim supplied with all models may be used in this
cabinet configuration. Be sure to adjust the “overlap”
dimension associated with the stainless-steel trim.
Please call 1-800-626-2000 with any questions.
H The opening center line dimension is taken at the
FRONT OPENING of each enclosure.
ELEC.
SEE NOTE D
ELEC.
SEE NOTE D
HEARTH OVEN PLATFORM
SEE NOTE B
41
2"10"
51
4"91
2"
11
16 "
OVERLAP
11
16 "
OVERLAP
3
16 "
OVERLAP
SEE NOTE G
11
16 "
OVERLAP
1"
OVERLAP
A
ASECTION A-A
27 3
32 "
C
LTO C
L
SEE NOTE H
7
8"
SEE NOTE F
28 1
2"
CUTOUT WIDTH
1
2"
SEE NOTE F
1
2"
SEE NOTE F
28 1
2"
CUTOUT WIDTH 45" MIN
22 9
16 "
7
16 "
SEE NOTE F
2"
BETWEEN
CUTOUTS
27 5
8"
23 1
2"
CABINET DEPTH
12 31-2001053 Rev. 1
Installations
1 F HEARTH OVEN OVER WALL OVEN – FLUSH-INSET INSTALLATION WITH A
2” PLATFORM BETWEEN
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Hearth Oven Platform must be able to support
200 lbs. (91kg).
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 24-15/16”
cabinet depth. Junction box may also be located in
an adjacent cabinet.
E The front surface of the interior cleats shall be a
finished appearance surface.
F The Wall Oven REQUIRES an extruded aluminum
LOWER VENT TRIM. Wall oven models beginning
with “ZTSX” already include the aluminum vent
trim. For models beginning with “ZTS”, the vent trim
kit ZX30VT1 must be ordered which includes the
aluminum vent trim and mounting hardware.
Please call 1-800-626-2000 with any questions.
G The opening center line dimension is taken at the
FRONT OPENING of each enclosure.
H Wall Oven bottom surface cleat is to be 1/4” thick
MDF fiber board or equivalent.
ELEC.
SEE NOTE D
ELEC.
SEE NOTE D
HEARTH OVEN PLATFORM
SEE NOTE B
41
2"10"
51
4"91
2"
A
A
28 5
32 "
C
LTO C
L
SEE NOTE G
24 15
16 "
CABINET DEPTH
SECTION A-A
3
4"
CLEAT
3
4"
CLEAT
3
4"
CLEAT
3
4"
CLEAT
11
8"
CLEAT
11
8"
CLEAT
45" MIN.
30"
CUTOUT WIDTH
30"
CUTOUT WIDTH
23 11
16 "7
8"
HEARTH OVEN
CLEAT SETBACK
28 5
8"
17
16 "
WALL OVEN
CLEAT SETBACK
1
4"
MDF CLEAT
SEE NOTE H
21
2"
CLEAT
DEPTH
2"
BETWEEN
CUTOUTS
31-2001053 Rev. 1 13
Installations
1 G HEARTH OVEN OVER FRENCH DOOR WALL OVEN –STANDARD
INSTALLATION WITH A MINIMUM GAP BETWEEN
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Hearth Oven Platform must be able to support
200 lbs. (91kg).
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 23-1/2” cabinet
depth. Junction box may also be located in an
adjacent cabinet.
E A minimum 1/8” reveal BEYOND the OVERLAP
dimensions is recommended for proper drawer and
door operating clearance. For the Lower FRENCH
DOOR WALL OVEN, please carefully refer to the
door opening restrictions associated with nearby
countertops, walls and cabinet fronts to adjust the
overlap value accordingly.
F Exterior cleats may be added to the sides and top
of the Hearth Oven opening in order to bring the
front surface of the Hearth Oven into alignment with
the front surface of the wall oven below. Finish per
customer requirements. A flat black finish may better
match the side appearance of the oven below.
G For the FRENCH DOOR WALL OVEN, the
stainless-steel LOWER TRIM supplied with the unit
is the only option.
H The opening center line dimension is taken at the
FRONT OPENING of each enclosure.
ELEC
ELEC
HEARTH OVEN PLATFORM
SEE NOTE B
10"
41
2"
91
2"
51
4"
11
16 "
OVERLAP
SEE NOTE E
11
16 "
OVERLAP
SEE NOTE E
11
16 "
OVERLAP
11
4"
OVERLAP
A
ASECTION A-A
25 13/16" MIN.
C
LTO C
L
SEE NOTE H
28 1
2"
CUTOUT WIDTH
28 1
2"
CUTOUT WIDTH
45" MIN.
7
8"
SEE NOTE F
1
2"
SEE NOTE F
1
2"
SEE NOTE F
23
32 "MIN
3/4" PLYWOOD
23 1
2"
CABINET DEPTH
27 5
8"
22 9
16 "
7
8"
SEE NOTE F
14 31-2001053 Rev. 1
Installations
1 H HEARTH OVEN OVER FRENCH DOOR WALL OVEN –STANDARD
INSTALLATION WITH A 2” PLATFORM BETWEEN
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Hearth Oven Platform must be able to support
200 lbs. (91kg).
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 23-1/2” cabinet
depth. Junction box may also be located in an
adjacent cabinet.
E A minimum 1/8” reveal BEYOND the OVERLAP
dimensions is recommended for proper drawer and
door operating clearance. For the Lower FRENCH
DOOR WALL OVEN, please carefully refer to the
door opening restrictions associated with nearby
countertops, walls and cabinet fronts to adjust the
overlap value accordingly.
F Exterior cleats may be added to the sides and top
of the Hearth Oven opening in order to bring the
front surface of the Hearth Oven into alignment with
the front surface of the wall oven below. Finish per
customer requirements. A flat black finish may better
match the side appearance of the oven below.
G For the FRENCH DOOR WALL OVEN, the
stainless-steel LOWER TRIM supplied with the unit
is the only option.
H The opening center line dimension is taken at the
FRONT OPENING of each enclosure.
ELEC.
SEE NOTE D
ELEC.
SEE NOTE D
HEARTH OVEN PLATFORM
SEE NOTE B
41
2"10"
51
4" 9 1
2"
11
16 "
OVERLAP
11
16 "
OVERLAP
SEE NOTE E
11
4"
OVERLAP
11
16 "
OVERLAP
SEE NOTE E
1"
OVERLAP
A
ASECTION A-A
27 3
32 "
C
LTO C
L
SEE NOTE H
7
8"
SEE NOTE F
28 1
2"
CUTOUT WIDTH
1
2"
SEE NOTE F
1
2"
SEE NOTE F
28 1
2"
CUTOUT WIDTH 45" MIN
23 1
2"
CABINET DEPTH
27 5
8"
22 9
16 "
7
8"
SEE NOTE F
2"
BETWEEN
CUTOUTS
31-2001053 Rev. 1 15
Installations
1 I HEARTH OVEN OVER STEAM OVEN –STANDARD INSTALLATION WITH A
MINIMUM GAP BETWEEN
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Hearth Oven Platform must be able to support
200 lbs. (91kg). For this installation, it is highly
recommended to lock the platform into the side
walls using wood joinery such as a Dado Joint.
Fasteners and wood glue are also encouraged to
further reinforce the locking wood joinery. The wood
grain of the platform shall be oriented left to right.
The front nose of the platform shall be a finished
appearance surface. See illustrations 1Q & 1R for
joinery concepts.
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 23-1/2” cabinet
depth. Junction box may also be located in an
adjacent cabinet.
E A minimum 1/8” reveal BEYOND the OVERLAP
dimensions is recommended for proper drawer and
door operating clearance.
F Exterior cleats may be added to the sides and top
of the Hearth Oven opening in order to bring the
front surface of the Hearth Oven into alignment with
the front surface of the wall oven below. Finish per
customer requirements. A flat black finish may better
match the side appearance of the oven below.
G A LOWER VENT TRIM option is NOT available for
this cabinet configuration.
H The opening center line dimension is taken at the
FRONT OPENING of each enclosure.
ELEC
SEE NOTE D
HEARTH OVEN PLATFORM
SEE NOTE B
ELEC
41
2"
10"
11
16 "
OVERLAP
3
4"
OVERLAP
11
16 "
OVERLAP
11
16 "
OVERLAP
91
2"
51
4"
A
A
21 3/64" MIN
C
LTO C
L
SEE NOTE H
SECTION A-A
7
8"
SEE NOTE F
1
2"
SEE NOTE F
1
2"
SEE NOTE F
28 1
2"
CUTOUT WIDTH
15
8"
CLEAT
15
8"
CLEAT
45" MIN
28 1
2"
CUTOUT WIDTH
1
2"
SEE NOTE F
22 9
16 "
23 1
2"
CABINET DEPTH
18 3
32 "
21
2"
CLEAT DEPTH
23
32 "MIN
3/4" PLYWOOD
16 31-2001053 Rev. 1
Installations
1 J HEARTH OVEN OVER STEAM OVEN – FLUSH-INSET INSTALLATION WITH A
MINIMUM GAP BETWEEN
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Hearth Oven Platform must be able to support
200 lbs. (91kg). For this installation, it is highly
recommended to lock the platform into the side
walls using wood joinery such as a Dado Joint.
Fasteners and wood glue are also encouraged to
further reinforce the locking wood joinery. The wood
grain of the platform shall be oriented left to right.
The front nose of the platform shall be a finished
appearance surface. See illustrations 1Q & 1R for
joinery concepts.
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 24-15/16”
cabinet depth. Junction box may also be located in
an adjacent cabinet.
E The front surface of the interior cleats shall be a
finished appearance surface.
F An optional LOWER TRIM KIT may be installed with
a CUT OUT OPENING & BOTTOM CLEAT height
changes. Trim kit ZXSTEAM1 can be used with
a CUT OUT OPENING height of 19-25/32” and a
BOTTOM CLEAT height of 1-5/8”.
Please call 1-800-626-2000 with any questions.
G The opening center line dimension is taken at the
FRONT OPENING of each enclosure.
H Steam Oven bottom surface cleat is to be 5/8” thick
MDF fiber board or equivalent.
ELEC.
SEE NOTE D
ELEC.
HEARTH OVEN PLATFORM
SEE NOTE B
STEAM OVEN PLATFORM
SEE NOTE H
10"
41
2"
91
2"
51
4"
A
A
SECTION A-A
11
8"
CLEAT
3
4"
CLEAT
3
4"
CLEAT
23
8"
CLEAT
23
8"
CLEAT
30"
CUTOUT WIDTH
30"
CUTOUT WIDTH
45" MIN
21 61/64" MIN
C
LTO C
L
SEE NOTE G
21
2"
CLEAT DEPTH
7
8"
HEARTH OVEN
CLEAT SETBACK
23 11
16 "
5
8"
MDF
SEE NOTE H
18 25
32 "
24 15
16 "
CABINET DEPTH
11
2"
STEAM OVEN
CLEAT SETBACK
23
32 " MIN
"3/4 PLYWOOD"
31-2001053 Rev. 1 17
Installations
1 K HEARTH OVEN OVER STEAM OVEN –STANDARD INSTALLATION WITH A
2” PLATFORM BETWEEN
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Hearth Oven Platform must be able to support
200 lbs. (91kg).
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 23-1/2” cabinet
depth. Junction box may also be located in an
adjacent cabinet.
E A minimum 1/8” reveal BEYOND the OVERLAP
dimensions is recommended for proper drawer and
door operating clearance.
F Exterior cleats may be added to the sides and top
of the Hearth Oven opening in order to bring the
front surface of the Hearth Oven into alignment with
the front surface of the wall oven below. Finish per
customer requirements. A flat black finish may better
match the side appearance of the oven below.
G A LOWER VENT TRIM option is NOT available for
this cabinet configuration.
H The opening center line dimension is taken at the
FRONT OPENING of each enclosure.
ELEC.
SEE NOTE D
ELEC.
SEE NOTE D
HEARTH OVEN PLATFORM
SEE NOTE B
41
2"10"
51
4"
91
2"
3
4"
OVERLAP
1"
OVERLAP
11
16 "
OVERLAP
11
16 "
OVERLAP
11
16 "
OVERLAP
7
8"
SEE NOTE F
1
2"
SEE NOTE F
1
2"
SEE NOTE F
28 1
2"
CUTOUT WIDTH
28 1
2"
CUTOUT WIDTH
15
8"
CLEAT
15
8"
CLEAT
1
2"
SEE NOTE F
22 9
16 "
17 3
4"
2"
BETWEEN
CUTOUTS
23 1
2"
CABINET DEPTH
21
2"
CLEAT DEPTH
SECTION A-A
22 5/32"
C
LTO C
L
SEE NOTE H
11
16 "
OVERLAP
11
16 "
OVERLAP
A
A
18 31-2001053 Rev. 1
Installations
1 L HEARTH OVEN OVER STEAM OVEN – FLUSH-INSET INSTALLATION WITH A
2” PLATFORM BETWEEN
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Hearth Oven Platform must be able to support
200 lbs. (91kg).
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 24-15/16”
cabinet depth. Junction box may also be located in
an adjacent cabinet.
E The front surface of the interior cleats shall be a
finished appearance surface.
F An optional LOWER TRIM KIT may be installed
with a CUT OUT OPENING & BOTTOM CLEAT
height changes. Trim kit ZXSTEAM1 can be used
with a CUT OUT OPENING height of 20-3/8” and a
BOTTOM CLEAT height of 1-5/8”.
Please call 1-800-626-2000 with any questions.
G The opening center line dimension is taken at the
FRONT OPENING of each enclosure.
H Steam Oven bottom surface cleat is to be 5/8” thick
MDF fiber board or equivalent.
ELEC.
SEE NOTE D
ELEC.
HEARTH OVEN PLATFORM
SEE NOTE B
STEAM OVEN PLATFORM
SEE NOTE H
41
2"10"
51
4"
91
2"
45" MIN
30"
CUTOUT WIDTH
30"
CUTOUT WIDTH
11
8"
CLEAT
3
4"
CLEAT
3
4"
CLEAT
23
8"
CLEAT 23
8"
CLEAT
1"
CLEAT
23 17/32"
C
LTO C
L
SEE NOTE G
7
8"
HEARTH OVEN
CLEAT SETBACK
11
2"
STEAM OVEN
CLEAT SETBACK
24 15
16 "
CABINET DEPTH
2"
BETWEEN
CUTOUTS
5
8"
MDF
SEE NOTE H
19 3
8"
23 11
16 "
2
1
2"
CLEAT
DEPTH
SECTION A-A
A
A
31-2001053 Rev. 1 19
Installations
1 M HEARTH OVEN OVER WARMING DRAWER –STANDARD INSTALLATION
WITH A MINIMUM GAP BETWEEN
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Hearth Oven Platform must be able to support
200 lbs. (91kg). For this installation, it is highly
recommended to lock the platform into the side
walls using wood joinery such as a Dado Joint.
Fasteners and wood glue are also encouraged to
further reinforce the locking wood joinery. The wood
grain of the platform shall be oriented left to right.
The front nose of the platform shall be a finished
appearance surface. See illustrations 1Q & 1R for
joinery concepts.
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 23-1/2” cabinet
depth. Junction box may also be located in an
adjacent cabinet.
E A minimum 1/8” reveal BEYOND the OVERLAP
dimensions is recommended for proper drawer and
door operating clearance.
F Exterior cleats may be added to the sides and top
of the Hearth Oven opening in order to bring the
front surface of the Hearth Oven into alignment with
the front surface of the wall oven below. Finish per
customer requirements. A flat black finish may better
match the side appearance of the oven below.
G The opening center line dimension is taken at the
FRONT OPENING of each enclosure.
ELEC
SEE NOTE D
HEARTH OVEN PLATFORM
SEE NOTE B
11
16 "
OVERLAP
11
16 "
OVERLAP
11
16 "
OVERLAP 11
16 "
OVERLAP
41
2"
10"
7
8"
SEE NOTE F
1
2"
SEE NOTE F
1
2"
SEE NOTE F
28 1
2"
CUTOUT WIDTH
28 1
2"
CUTOUT WIDTH 16 31/64"
C
LTO C
L
SEE NOTE G
3
8"
SEE NOTE F
22 9
16 "
831
32 "23 1
2"
CABINET DEPTH
23
32 "MIN
"3/4 PLYWOOD"
SECTION A-A
A
A
20 31-2001053 Rev. 1
Installations
1 N HEARTH OVEN OVER WARMING DRAWER – FLUSH-INSET INSTALLATION
WITH A MINIMUM GAP BETWEEN
A 45” is the required minimum installation height. Oven
may be installed higher based on owner preference.
B Hearth Oven Platform must be able to support
200 lbs. (91kg). For this installation, it is highly
recommended to lock the platform into the side
walls using wood joinery such as a Dado Joint.
Fasteners and wood glue are also encouraged to
further reinforce the locking wood joinery. The wood
grain of the platform shall be oriented left to right.
The front nose of the platform shall be a finished
appearance surface. See illustrations 1Q & 1R for
joinery concepts.
C Solid enclosure required on the top, bottom, left
side, right side and back. The back surface may
be drywall. Advanced fabrication and assembly
techniques are strongly encouraged to ensure
precise cabinet squareness and parallelism.
D Junction box location: Must be flush with back
surface so as not to extend into the 24-15/16”
cabinet depth. Junction box may also be located in
an adjacent cabinet.
E The front surface of the interior cleats shall be a
finished appearance surface.
F The opening center line dimension is taken at the
FRONT OPENING of each enclosure.
ELEC.
SEE NOTE D
HEARTH OVEN PLATFORM
SEE NOTE B
10"
41
2"
11
8"
CLEAT
3
4"
CLEAT
3
4"
CLEAT
45" MIN
30"
CUTOUT WIDTH
30"
CUTOUT WIDTH
3
4"
CLEAT
3
4"
CLEAT
17 39/64" MIN
C
LTO C
L
SEE NOTE F
21
2"
CLEAT
DEPTH
7
8"
HEARTH OVEN
CLEAT SETBACK
23 11
16 "
11
8"
CLEAT
10 3
32 "13
8"
WARMING DRAWER
CLEAT SETBACK
24 15
16 "
CABINET DEPTH 23
32 "MIN
"3/4 PLYWOOD"
SECTION A-A
A
A
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
dans d''autres langues
- English: Monogram ZEP30FRSS User manual
- español: Monogram ZEP30FRSS Manual de usuario