LSTU Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, and its affiliated corporations and
subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® and Thinstall™ are registered trademarks of Milestone
AV Technologies. All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the LSTU up to (and
including) the display does not exceed 125 lbs (56.7 kg).
•The weight capacity of the LSTU may be LIMITED to
the lowest weight capacity of any other component or
accessory used within the mounting system.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: The depth of the display cannot exceed
5 inches (127 mm).
WARNING: The LSTU fits all hole patterns between 200 x
200 mm and 800 x 500 mm.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! : The LSTU mount is designed to be mounted
to: • 2" x 4" wood studs that are 16" on center (for triple-stud
mounting) covered with drywall of 5/8" maximum
thickness, or
•2" x 4" wood studs that are 16", 20" or 24" on center (for
double-stud mounting) covered with drywall of 5/8"
maximum thickness, or
•a bare concrete wall with a minimum thickness of 8", or
•a bare 8" x 8" x 16" concrete block wall.
--SAVE THESE INSTRUCTIONS--
Installation Instructions LSTU
3
DIMENSIONS
16.0 0
406
20.0 0
508
24.0 0
610
32.0 0
813
ACCESS
ANGLE
7°
CABLE
83
3.28
RELEASE STRAPS
CABLE STAND
INTERFACE
LOCKING
SWITCH
4.44
628
24.71
35.6 9
113
MAX 31.50 [800]
MIN 7.87 [200]
906
4X
79
3.09
7
.29
37
1.44
40
500
19.6 9
1.58
33
1.29
.39
10
DIMENSIONS: [MILLIMETERS]
INCHES
LSTU Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Measure
Medir
Messen
Medir
Misurare
Meten
Mesurer
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Hammer
Martillo
Hammer
Martelo
Martello
Hamer
Marteau
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Installation Instructions LSTU
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
3/16" (4.8mm) M2.5 (included)
M3 (included)
M4 (included)
M5 (included)
5/16" (7.9mm) M4 (included)
M6 screws]
S (4)
B (2)
C (1)
M4
D (6) E (4) F (4) G (4) H (4) J (4)
K (4) L (4) Q (4)
R (4) T (4) U (4) V (4)
W (1)
X (1) Y (1) Z (1)
M7 x 70 M4 x 12 M5 x 12 M6 x 12 M4 x 25
M6 x 25 M8 x 40
.5"
M5 M4 M3 M2.5
[Shoulder washer for M4 [Shoulder washer for
AA (6)
and M5 screws]
M (4) N (4)
M8 x 16
A (1)
M8 x 25
.25"
M8 x 20
M5 x 25
#10
[Wall plate] [Upright]
P (4)
M8 x 10
[Anchor]
LSTU Installation Instructions
6
Assembly And Installation
Wall Plate Installation Using Wood Studs
1. Determine location for mount keeping in mind display size
and safety requirements.
2. Use stud finder to locate studs. Wall plate can be mounted
on 2" x 4" wood studs either 16", 20" or 24" apart for double-
stud mounting. For triple-stud mounting, studs must be 16"
apart.
3. Remove and discard two plastic shipping parts from the wall
plate (one from each end). (See Figure 1)
Figure 1
4. Using wall plate as template, mark and then drill four or six
(for triple-stud mounting) 3/16" diameter pilot holes through
mounting surface, making sure the holes are centered in the
middle of each stud. Holes must be drilled at least 2-1/4"
deep. (See Figure 2)
5. Install four or six connector screws (D) through wall plate
and into pilot holes using M4 Allen Head bit (C). (See
Figure 2)
Wall Plate Installation into Concrete or Concrete
Block
1. Determine location for mount keeping in mind display size
and safety requirements.
2. Using wall plate as a template, mark and then drill six 5/16"
diameter pilot holes through mounting surface. Use level to
make sure wall plate is perfectly horizontal. Holes must be
drilled at least 2-1/4" deep. (See Figure 3)
3. Install six anchors (AA) into pilot holes drilled in Step 2. Use
a hammer to lightly tap anchors into holes. (See Figure 3)
4. Install six connector screws (D) through wall plate holes and
into anchors. (See Figure 3)
Display Installation
1. Lay display face side down on a level, non-abrasive
surface. Lay down a cloth if necessary to avoid scratching
the screen.
2. Position two interface brackets (B) over holes in back of
display to determine which holes will be used for
installation.
NOTE: Interface brackets should be positioned so that the
diamond hole in the bracket is located halfway between
the installation holes in order to ensure proper weight
distribution.
NOTE: Spacers may not be required depending on the type of
display being mounted. They will typically only be used
with recessed or bump-out back screens.
NOTE: Cable management pull straps should be easily
accessible underneath the display. Length of straps
can be adjusted if necessary.
Figure 2
Figure 3
Front of
wall plate
3
Shipping
part
(Double-stud mounting with studs 20" apart shown)
x 4
4
x 4
5
(D) x 4
holes for 16" studs
holes for 24" studs
(Triple-stud mounting)
x 6
4
x 6
5
(D) x 6
2
4
(D) x 6
3
(AA) x 6
x 6
x 6
Installation Instructions LSTU
7
Figure 4
(B) x 2
5
(E-Q) x 4
(R) x 4 (if necessary)
(S or T) x 4 (if necessary)
(U or V) x 4 (if necessary)
Flag in open position
Display
3. Determine which screws to use to connect interface
brackets to display. Use the screws that fit into the holes on
the back of the display. Make sure screws can make at least
three full turns into mounting holes. If not, select longer
screw from hardware kit.
4. Determine which washers and shoulder washers to use with
the corresponding screw. Refer to table below for details.
5. Install four button head cap screws (E - Q) through required
washers (R) and shoulder washers (S or T), interface
brackets (B), spacers (U or V) and into holes on back of
display. (See Figure 4)
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Displays can weigh in
excess of 40 lbs (18.1 kg). ALWAYS use two people and
proper lifting techniques when installing display.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the LSTU up to (and
including) the display does not exceed 125 lbs (56.7 kg).
NOTE: Make sure locking flags are in the open position before
attaching display to wall plate. Flags are shown in the
open position in Figure 4.
NOTE: Display can be adjusted horizontally as long as guide
hooks are securely attached to wall plate.
IMPORTANT ! : If spacers are required, be sure to use
screws that are longer than the spacers but of the same
diameter!
6. While supporting both sides of display, lift display up to the
wall plate on the wall.
Screw Size Washers Shoulder Washers
M4 use R use S
M5 use R use S
M6 none use T
M8 none none
LSTU Installation Instructions
8
7. Slowly guide hooks on top of interface brackets on top of
wall plate in desired mounting location. (See Figure 5)
8. Slowly swing display toward wall. (See Figure 5)
Figure 5
9. Slowly pull bottom of display away from wall until kickstand
fully reaches its down position. (See Figure 6)
10. Slowly release display until kickstand locks against bottom
of mount.
11. Rotate flags on each interface bracket to the closed position
in order to lock brackets to wall plate. (See Figure 6)
Figure 6
NOTE: Flags should stay in locked position unless removing
display from wall bracket.
WALL
7
8
Kickstand in
down position
Locking flag
11
9
Installation Instructions LSTU
9
Cable Management
NOTE: For attaching and adjusting cables, the LSTU mount
features a kickstand to allow access without having to
remove display from the wall.
1. Ensure kickstand is firmly in down position.
2. Attach or adjust cables as necessary on back of display.
3. To disengage kickstand, slightly pull display away from wall
and pull down on cable management straps to release
kickstand. Slowly allow display to return to the wall. (See
Figure 7)
Figure 7
NOTE: Due to the low-profile design of the Thinstall Series,
displays with cable connections coming straight out of
the back may require 90-degree cable connectors.
Chief offers in-wall accessories that can assist with
recessing cables and connections.
NOTE: Certain displays may have limited space available for
cable management.
WALL
Cable
management
Cables (typical)
straps
Kickstand in down
position
1
3
Installation Instructions LSTU
11
LSTU Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002507 Rev00
2014 Milestone AV Technologies
www.chiefmfg.com
03/14
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
dans d''autres langues
- English: Chief LSTU Installation guide
Documents connexes
-
Chief FMSITL Guide d'installation
-
-
Chief ICMPFM3B02 Guide d'installation
-
-
-
Chief iCXPTM3B02 Guide d'installation
-
Chief ICXPTM3B03 Guide d'installation
-
-
-