DT041
WOS3-PC
Product Overview
The Daintree® Wireless Battery-Powered Ceiling Mounted Occupancy and Daylight Sensor may be deployed in a Daintree
EZ Connect or Daintree Networked application. The WOS3-PC device is designed for ceiling installation on suspended
ceiling tiles, or to drywall. This device is designed for energy savings based on space occupancy status and ambient light
level. The communication with the Daintree system utilizes a secure and reliable wireless connection which helps minimize
installation costs and complexity.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Save these instructions for future use.
IMPORTANT
To ensure the product warranty is valid, please ensure
all installation instructions and environmental conditions
for storage and operation are complied with.
Installation to be performed by factory trained or qualified
personnel.
Save These Instructions
Use only in the manner intneded by the manufacturer.
If you have any questions, contact the manufacturer.
Daintree® Wireless Controls
Wireless Battery-Powered Ceiling
Mounted Occupancy and Daylight Sensor
Installation of Back Plate onto Wall
Installation Guide
2
123
45
Counterclockwise rotation
to separate the back plate
from the device.
Remove the insulation sheet.emove
(This step is for installing on
wood or cement, if installing
on drywall, jump this step.)
Insert the expansion bolt
into the hole.
For installing on drywall, pass
the screws through the installing
holes on the back plate. For
installing on wood or cement,
screw should pass the screws
and align with the hole drilled
in step3.
(This step is for installing on
wood or cement, if installing
on drywall, jump this step.)
Drill a hole vertically on the
wall. The hole diameter equal
to the size of the expansion bolt.
Daintree® Wireless Controls Wireless Battery-Powered
Ceiling Mounted Occupancy and Daylight Sensor
(WOS3-PC)
6For installing on drywall, lock
the screw vertically on the wall.
For installing on wood or cement,
lock the screw into expansion
bolts.
Installation Guide
3
Installation of Device onto Back Plate
Install new battery. then reverse previous
steps to finish the battery replacement.
(Only use CR14505 for WOS3-PC)
Clockwise rotation to install
the device onto back plate.
12
Unscrew the screw
4
Align the device with back
plate by positioning hole.
Daintree® Wireless Controls Wireless Battery-Powered
Ceiling Mounted Occupancy and Daylight Sensor
(WOS3-PC)
Remove the cover of battery
5Remove the elder battery
6
Battery Replacement
Mask Replacement
Installation Guide
4
Product Dimensions
12
12
Put the ring into track, the
Lock icon should be 10
degree to the triangle.
Then clockwise rotate the ring.
When triangle is pointed to
the lock icon on the ring
Put the mask into track, the
triangle icon on mask is pointed
to the triangle icon on body. Then
clockwise or counter-clockwise
rotate the ring.
When the triangle icon on
mask is 90 degree to the
triangle icon on body, mask
is locked.
Daintree® Wireless Controls Wireless Battery-Powered
Ceiling Mounted Occupancy and Daylight Sensor
(WOS3-PC)
Daintree® Wireless Controls Wireless Battery-Powered
Ceiling Mounted Occupancy and Daylight Sensor
(WOS3-PC)
www.gecurrent.com
© 2021 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the
General Electric Company and are used under license. Information provided is subject to change without
notice. All values are design or typical values when measured under laboratory conditions.
DT041-Daintree-WWD2-2IW-Wall-Dimmer-Installation-Guide
Installation Guide
Product Name: Wireless Battery-Powered Ceiling Mounted Occupancy and Daylight Sensor
Model No: WOS3-PC
Supplier's Name: Current Lighting Solutions, LLC
Supplier’s Website: www.gecurrent.com
Supplier’s Address (USA): Cleveland, Ohio
Supplier’s Phone: 1-866-855-8629
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences
et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
ISED RF Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part
of your body.
Pour se conformer aux exigences de conformité CNR 102 RF exposition, une distance de séparation d'au moins 20 cm
doit être maintenue entre l'antenne de cet appareil ettoutes les personnes.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Daintree® Wireless Controls Wireless Battery-Powered
Ceiling Mounted Occupancy and Daylight Sensor
(WOS3-PC)
Installation Guide
5
Product Operation
Button Functionality
LED Indicator in Red
Rapid flash (12 times per second)
for up to 30 seconds
Solid ON for 10 seconds
Flashes once (100ms duration)
Flashes ON 2 seconds every
30 seconds
Device is trying to join a ZigBee network
Device successfully joined a ZigBee network
Device has been activated while in the network
Batteries need to be replaced
LED Indicator in Green
Flashes once(100ms duration)
Occupancy has been detected
Reset Button
Installation Test Mode ON
Enable/Disable LED Indicator
Reset to Factory default
Short Press
Double Short Press
Hold 5 Seconds
Daintree® Wireless Controls Wireless Battery-Powered
Ceiling Mounted Occupancy and Daylight Sensor
(WOS3-PC)
Installation Guide
6
Technical Data
SKU DESCRIPTION ARTICLE NO
93149829 Daintree Wireless Controls Wall Dimmer, In Wall, 2 Button, Battery WWD2-2IW
Product Specifications
Product Certifications
Product Availablity
Dimensions
Weight
Power Supply
Battery Life
Operating Environment
Status Indicator
Mounting
Warranty
Purpose of Control
Construction of Control
Type 1 Action
Pollution Degree 2
89mm D x 30mm H
81g (without battery)
(2) AA 3V battery
10 years (normal operation)
-10°C to 40°C (Indoor Use Only)
Network join status, Occupancy detected
Screw Mounted
5 years
Sensor Control
Independently Mounted
The alkaline batteries supplied with your wireless switch are prone to leak over their lifetime, particularly when the battery is mostly
depleted. In the event that your battery leaks alkaline into the battery compartment, the chemicals can damage the metal terminals.
The chances of this happening can be reduced by changing the batteries in the switch promptly when the batteries are nearing their
end of their useful life. If a battery leak should occur, however, it should be cleaned up to prevent damage to the wireless switch.
WARNING: THE CHEMICALS LEAKED FROM ALKALINE BATTERIES ARE CORROSIVE. WHEN HANDLING LEAKING BATTERIES, PROPER
PERSONAL SAFETY EQUIPMENT SHOULD BE USED, INCLUDING RUBBER GLOVES AND EYE PROTECTION.
If it is discovered that the batteries have leaked, wearing rubber gloves and using eye protection, remove all of the batteries from the
battery compartment and seal them in a plastic bag. The bag should be discarded in a manner in accordance with local laws and
regulations. Then, using a small cloth lightly moistened with vinegar or other mild acid, carefully wipe all of the leaked battery
chemicals from inside the battery compartment and allow it to dry. Once dry, the batteries may be replaced and the switch may be
reinstalled.
FCC ID: 2AS3F-WOS3PC
IC: 25008-WOS3PC
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
-
1
-
2
dans d''autres langues
Documents connexes
Autres documents
-
Daintree Networked WMZ10 People Counting Sensor Guide d'installation
-
Daintree WWD2-4IW Guide d'installation
-
Ring Smart Lighting Bridge App Mode d'emploi
-
Daintree WIT100 Manuel utilisateur
-
Daintree GE Lumination LSA Series Guide d'installation
-
Lumination RPL Series Controls Accessory Controller Bracket Guide d'installation
-
Daintree WANSI Wireless Area Controller Guide d'installation
-
Develco Humidity Guide d'installation
-
-
