Honeywell AlarmNet CELL-ANTST Guide d'installation
- Catégorie
- Antennes réseau
- Taper
- Guide d'installation
AlarmNet CELL-ANTST
Indoor Fixed Length Antenna
Installation and Setup Guide
General
The Communication Module uses an internal dual band cellular antenna. In most cases, this antenna will provide
sufficient signal strength for a successful installation.
The Honeywell Home Indoor Fixed Length Antenna should be used in installations where moving the antenna to a
higher point within the building will provide a better signal strength.
Installation Note: For best signal strength, maintain at least 12 inches of clearance between the communication
module and steel I-beams, HVAC ducts, metal studs, steel roofs or roofs, exterior walls with
metalized insulation or aluminum siding and other large metal objects.
Kit Includes: Antenna with cable
Antenna accessory pack
Hardware
Compatible Modules: Lyric-3G, Lyric-CDMA and Lyric-3GC.
Indoor Antenna
The antenna is not weatherproof, and must be installed indoors and mounted vertically while maintaining 12 inches
of clearance from large metal objects. Install the antenna as follows:
1. Find a suitable location that will allow the antenna to be mounted vertically.
2. Remove power; refer to the radio communication module installation guide for Replacing the Module.
3. Connect the short adapter cable to the antenna cable.
4. Using wire cutters, remove the knock-out area as shown below.
5. Plug the end of the adapter cable into the module’s external antenna port and route the cable as shown.
6. Refer to the Cellular Information screen on the Lyric controller to make sure the displayed signal strength is
adequate. See the radio communication module installation guide for specific ranges.
7. Permanently mount the antenna vertically using the included hardware.
Lyric-3G / Lyric-CDMA / Lyric-3GC Communication Module
PUSH
DOWN
ANTENNA PORT
cell-antst-001-V0
ANTENNA
CABLE
EXTERNAL
ANTENNA
BRACKET
CABLE
CLAMP
ADAPTER CABLE
NUT
LOCK
WASHER
Indoor, Fixed Length Antenna Installation
Specifications
Antenna Adapter Cable
Type
Dual band,
dipole, PCB
VSWR
<2:1
SMA female
to
TS9 straight SMA
Bands
824-896 MHz
1850-1990 MHz
Dimensions
143 x 27 mm
Polarization Linear Cover Polyolefin, black
Gain
(Average)
1dBi Cable Type RG-174
Impedance 50 Ohms Cable Length 3m
Input Power
(Max.)
10W
Connector
Type
SMA male
RF Exposure
Warning – The internal or external antenna(s) used with this product must be installed to provide a separation distance of at
least 7.8 in. (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna or
transmitter except in accordance with FCC multi-transmitter product procedures.
Mise en Garde
Exposition aux Fréquences Radio: L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de
séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.
IMPORTANT NOTE ABOUT EXTERNAL ANTENNAS
If an external cellular radio antenna is used, the antenna may be installed or replaced ONLY by a professional installer.
TO THE INSTALLER
For the communication module, the external antenna must not exceed a maximum directional gain (including cable loss) of
3.2 dBi at 850 MHz and 2.3 dBi at 1900 MHz.
The Honeywell Home Trademark is used under license from Honeywell International Inc.
This product is manufactured by Resideo Technologies, Inc. and its affiliates.
Ê800-20802V1C~Š
800-20802V1C 11/15 Rev. C
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
2020 Resideo Technologies, Inc.
www.resideo.com
-
1
-
2
Honeywell AlarmNet CELL-ANTST Guide d'installation
- Catégorie
- Antennes réseau
- Taper
- Guide d'installation