Access Lighting 62585LEDDLP Manuel utilisateur

Access Lighting
Marque
Access Lighting
Modèle
62585LEDDLP
Taper
Manuel utilisateur

Ce manuel convient également à

WHAT YOU NEED
• Screwdriver
• Wire Cutters
• Wiring Supplies as Specified
by Electrical Code
INSTALLATION INSTRUCTIONS
WHAT WE PROVIDE
• Mounting Hardware
• Mounting bracket
• 1 x Glass shade
• 1 x 6”, 16”, 22” rod
• 1 x A19 E26 LED bulb
COLLECTION
1
CERTIFICATION: cULus DRY
NO. 62585LEDDLP
62585LEDDLP
APPLICATION MODEL NO.
Pendant
IMPORTANT SAFETY INSTRUCTIONS
MESURES DE SECURITE A RESPECTURE
Before assembling your ACCESS LIGHTING fixture, please make sure that
you carefully read through this instruction sheet. Save this instruction sheet
and refer to it when additions to or changes in the fixture
configuration are made.
Lisez attentivement ce manuel d’instructions. Enregistrer cette feuille
d'instructions et de s'y référer lorsque les ajouts ou changements dans
la configuration de montage sont faites.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTOR.
CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES
CONDUCTEURS DE LA DERIVATION SONT ADEQUATS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION
AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT,
PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT
AINSI QUE LES RISQUES INHERENTS
NOTE: The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations
that may occur. It must be understood that common sense, caution and
care, are factors that can’t be built into any product. These factors must
be supplied by the person(s) caring for and operating the fixture.
Read all instructions
Do not install this fixture in hazardous locations.
N'installez pas cet appareil dans des emplacements dangereux.
Do not install any fixture assembly closer than 6 inches from any
curtain or similar combustible material.
Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute
surface combustible.
"WARNING Risk of Fire and Electric Shock."
“CAUTION: Risque d’ Incendie et de Choc Electriques.”
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances,
Local and the U.S. National Electrical Codes (NEC). These fixtures are
intended for mounting to a standard 4” metal octagon outlet box.
The box must be directly supported by the building structure and U.L.
Recognized.
STEP BY STEP INSTRUCTIONS
Before starting your installation disconnect the Power by turning off the
Circuit Breaker or by removing the fuse at the fuse box. Just turning the
light off at the light switch is not sufficient to prevent electrical shock.
Recommended Dimmers for Supplied LED bulb
(TRIAC) LEVITON Decora Sureslide 6672
(TRIAC) LEVITON Decora Sureslide 6674
(TRIAC) LUTRON Toggler TGCL-153P
(TRIAC) LUTRON Diva DVCL-153P
(TRIAC) LUTRON Skylark CL SCL-153 or SCL-153P
Oslo
1
WHAT YOU NEED
• Screwdriver
• Wire Cutters
• Wiring Supplies as Specified
by Electrical Code
2
4
2
CERTIFICATION: cULus DRY NO.
62585EDDLP
3
RESTORE THE ELECTRICITY AND
CHECK THE OPERATION OF YOUR
NEW ACCESS LIGHTING FIXTURE
VER: 21.11.1
Please ensure that the fitting is cool and
switched off before replacing the bulb.
DO NOT use bulbs that exceed the
maximum wattage, stated on caution label.
CAUTION
PREPARE THE FIXTURE
If there is an existing fixture remove it.
Determine the desired hanging height and secure the
included rods to the canopy and fixture.
Carefully pass the fixture wires through the rods to the canopy.
Expose the supply wires from the outlet box.
MOUNT THE MOUNTING BRACKET AND
MAKE WIRE CONNECTION
Attach the mounting bracket to the J-Box with the supplied
screws. Connect the black supply wire to the black fixture
wire. Secure with the supplied wire nuts. Connect the white
supply wire to the white fixture wire. Secure with the supplied
wire nuts. Attach the green J-Box wire around green
hexagonal head screw or connect it to the green supply
grounding wire of the fixture. Secure all wires with electrical
tape (not supplied). Tuck all wires carefully into the J-Box.
Align the canopy to the mounting bracket and secure with
the supplied screws.
INSERT THE GLASS SHADE AND THE BULB
Place the glass shade over the socket. Secure with the supplied
socket ring.
Insert the bulb.
DO NOT EXCEED THE MAXIMUM WATTAGE AS
STATED ON THE WARNING LABEL
  • Page 1 1
  • Page 2 2

Access Lighting 62585LEDDLP Manuel utilisateur

Access Lighting
Marque
Access Lighting
Modèle
62585LEDDLP
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents