RAB Lighting PLC-9-V-827-BYP Mode d'emploi

RAB Lighting
Marque
RAB Lighting
Modèle
PLC-9-V-827-BYP
Taper
Mode d'emploi
PLC-9-V-8XX-BYP
READ CAREFULLY BEFORE INSTALLING LED tube. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB LED tube must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is
required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNINGS:
WARNING - Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical
systems. If not qualified, do not attempt installation. Contact a qualified electrician.
AVERTISSEMENT - Risque d'incendie ou de choc électrique. Installation du kit de Retrofit LED exige une
connaissance des systèmes électriques luminaires. Si vous n'êtes pas qualifié, ne tentez pas de l'installation. Contactez
un électricien qualifié.
WARNING - Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and
dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the
input rating of the luminaire.
AVERTISSEMENT - Risque d'incendie ou de choc électrique. Installez ce kit dans les luminaires qui ont les
caractéristiques de construction et les dimensions indiquées dans les photographies et / ou dessins et où la cote d'entrée
du kit de modification ne dépasse pas la capacité d'entrée du luminaire.
WARNING -To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
AVERTISSEMENT - Pour éviter d'endommager le câblage ou à l'abrasion, ne pas exposer le câblage aux bords de tôle
ou d'autres objets pointus.
Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation or maintenance.
COMPACT LED TUBES
COMPACT LED TUBES
P LC-9-V-827-BYP
P LC-9-V-830-BYP
P LC-9-V-835-BYP
P LC-9-V-840-BYP
P LC-9-V-850-BYP
155x185 1
Model
Name
Installers should not disconnect existing wires from
lampholder terminals to make new connections at
lampholder terminals. Instead installers should cut
existing lampholder leads away from the lampholder and
make new electrical connections to lampholder lead wires
by employing applicable connectors.
Do not make or alter any open holes in an enclosure of
wiring or electrical components during kit installation.
THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT
OF A LUMINAIRE WHERE THE SUITABILITY OF THE
COMBINATION SHALL BE DETERMINED BY
AUTHORITIES HAVING JURISDICTION.
maximum one tubular lamp. The minimum lamp compartment dimensions
are tabulated below:
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two
conditions:(1)this device may not cause harmful interference,and (2)this device must accept any
interference received, including interference that may cause undesired operation.
WARRANTY
This product is warranted for 5 years from the date of purchase.If this product does not
perform t
kage, send an email or write to the
address below for product return and replacement. This replacement is the sole remedy
available. Liability for incidental or con- sequential damage is expressly excluded.
PLC-9-V-8XX-BYP
[Diameter x Height] [mm]
  • Page 1 1
  • Page 2 2

RAB Lighting PLC-9-V-827-BYP Mode d'emploi

RAB Lighting
Marque
RAB Lighting
Modèle
PLC-9-V-827-BYP
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents