VIZION FULHAM VJTUNV015LNxyyB11 12 Inch Wall Sconce Luminaire Manuel utilisateur

Taper
Manuel utilisateur
LED WALL SCONCE KIT
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 [email protected] www.fulham.com
Installation Instructions subject to change without notice. Page 1 of 7
INSTALLATION INSTRUCTIONS
12” WALL SCONCE LUMINAIRE
RETROFIT KIT INSTALLATION MANUAL
FOR 12” WALL SCONCE LUMINAIRES
VJTUNV015LNxyyB11
1/6/22 INS-AC-LN11-WS, Rev C
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 [email protected] www.fulham.com
Installation Instructions subject to change without notice. Page 2 of 7
1.0 INSTALLATION WARNINGS
1.0 AVERTISSEMENTS D'INSTALLATION
1.
2.
3.
4.
5.
6.
7.
8.
"THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND HAZARDS INVOLVED.”
“WARNING - Risk of fire or electric shock. LED Retrofit kit installation requires knowledge of luminaires
electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.”
“WARNING - Risk of fire or electric shock. Install this kit only in the luminaires that has the construction features
and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not
exceed the input rating of the luminaire.”
“WARNING - To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other
sharp objects.”
“WARNING –Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling
for installation of LED retrofit kit. Check for enclosed wiring and components."
"CAUTION – RISK OF FIRE. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTOR."
“THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY
OF THE COMBINATION SHALL BE DETERMINED BY THE AUTHORITIES HAVING JURISDICTION.”
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
1.
2.
3.
4.
5.
6.
7.
8.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION PERTINENT, PAR UNE
PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES
INHÉRENTS.
AVERTISSEMENT - Risque d’incendie ou de choc électrique. L’installation de ce nécessaire de modernisation
exige une personne familière avec la construction et le fonctionnement du système électrique du luminaire et
des risques associés. Toute personne qui n’est pas qualifiée ne doit faire aucune tentative d’installation et doit
contacter une personne qualifiée.
AVERTISSEMENT - Risque d’incendie ou de choc électrique. N’installer ce nécessaire que dans les luminaires
don't les caractéristiques de construction et les dimensions sont conforme à celles illustrées dans les photos
et/ou les dessins et dont la puissance d’entrée nominale du nécessaire de modernisation ne dépasse pas celle
du luminaire.
AVERTISSEMENT - Afin de prévenir l’endommagement ou l’abrasion des câbles, éviter tout contact entre ces
derniers et le bord d’un objet tranchant tel qu’une tôle.
“AVERTISSEMENT -Risk d'incendie ou de choc électrique. Le câblage du luminaire et les pièces électriques
peuvent être endommagés lors du forage pour l'installation d'un kit de reconditionnement LED. Vérifiez le
câblage et les composants inclus. "
ATTENTION – RISQUE D'INCENDIE, CONSULTER UN ÉLECTRICIEN QUALIFIÉ POUR VOUS
ASSURER QUE LES CONDUCTEURS DE LA DÉRIVATION SONT ADÉQUATS.
LE NÉCESSAIRE DE MODERNISATION EST ACCEPTÉ À TITRE DE COMPOSANT D’UN LUMINAIRE
LORSQUE LA PERTINENCE DE LA COMBINAISON DOIT ËTRE DÉTERMINÉE PAR PAR LES
AUTORITÉS COMPÉTENTES.
Ne faites pas ou ne modifiez aucun trou ouvert dans une enceinte de câblage ou de composants électriques
pendant l'installation du kit
LED WALL SCONCE KIT
RETROFIT KIT INSTALLATION MANUAL
FOR 12” WALL SCONCE LUMINAIRES
1/6/22 INS-AC-LN11-WS, Rev C
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 [email protected] www.fulham.com
Installation Instructions subject to change without notice. Page 3 of 7
Retrofit kit components will be provided as listed below:
4.0 RECOMMENDED TOOLS (Not Included)
3.0 RETROFIT KIT COMPONENTS
Power Drill W/ Phillips Bit
Original Luminaire Minimum Luminaire
Dimensions
(Minka-Lavery: 9812-166)
2.0 ORIGINAL LUMINAIRE DIMENSIONS
Remove all the original luminaire parts, hardware, lamp, and ballast in order to begin the retrofit.
Original luminaire diffuser and original ground wire will need to be kept for this retrofit.
This Kit can be retrofitted into any luminaire with a similar length/height width greater than or equal to the Minimum
Luminaire Dimensions described above or volume greater or equal to 201.4 cubic inches.
LED Engine Mounting Hardware Retrofit Label Input Connector
Retrofit kit components will be provided as listed below:
6.0”
12.0” 4.0”
Back Side
Front Side
Lens
LED WALL SCONCE KIT
RETROFIT KIT INSTALLATION MANUAL
FOR 12” WALL SCONCE LUMINAIRES
This luminaire has been modified and can no
longer operate the originally intended lamp.
Ce luminaire a été modifié et ne peut plus
utiliser la lampe prévue à l'origine.
1/6/22 INS-AC-LN11-WS, Rev C
NOTE: Wire on dedicated lighting branch circuit. Do not wire on same branch circuit as motors, heating elements,
inductive type loads or heavy machinery which may introduce spikes, noise and other abnormalities onto the Line.
Doing so may result in damage to the unit or abnormal lighting conditions.
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 [email protected] www.fulham.com
Installation Instructions subject to change without notice. Page 4 of 7
5.0 RETROFIT KIT DESCRIPTION
ITEM
DESCRIPTION
QTY
A.
LED AC Engine
1
B.
6-20 X 3/8” Self Drilling Screws
6
C.
Retrofit Label
1
D.
Input Connector (may vary from picture)
1
B
A
C
D
LED WALL SCONCE KIT
RETROFIT KIT INSTALLATION MANUAL
FOR 12” WALL SCONCE LUMINAIRES
This luminaire has been modified and can no
longer operate the originally intended lamp.
Ce luminaire a été modifié et ne peut plus
utiliser la lampe prévue à l'origine.
1/6/22 INS-AC-LN11-WS, Rev C
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 [email protected] www.fulham.com
Installation Instructions subject to change without notice. Page 5 of 7
Start by removing the Lens from the
luminaire. See Picture #1.
Remove the lamp and lamp socket from the
luminaire. See Picture #2.
The original luminaire ground wire will need
to be kept for this retrofit.
The luminaire back plate should look like
Picture #2 in order to begin the retrofit.
1.
2.
3.
6.0 ORIGINAL LUMINAIRE DISASSEMBLY
Picture #1
Picture #2 Back Side
Front Side
LED WALL SCONCE KIT
RETROFIT KIT INSTALLATION MANUAL
FOR 12” WALL SCONCE LUMINAIRES
1/6/22 INS-AC-LN11-WS, Rev C
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 [email protected] www.fulham.com
Installation Instructions subject to change without notice. Page 6 of 7
Start by inserting wires into the input
connectors on either side of the LED
Engine (A). See Figure 1.
1.
Figure 1
Figure 2
Secure the LED Engine to the luminaire
mounting plate using the provided 6-20 x3/8”
Self Drilling Screws (B). See Figure 3.
NOTE: All screws provided must be used to
ensure good thermal contact to surface.
3.
Figure 3
7.0 RETROFIT KIT ASSEMBLY
Insert input leads Into LED Engine
Route the input wires of LED Engine (A) into
the wire hole of the luminaire back plate and
place the LED Engine (A) onto the luminaire
back plate as shown on Figure 2.
NOTE: LED Engine must make direct contact
with the back plate when installed in order to
provide sufficient heat sinking to properly
manage thermals for safety and warranty
purposes. The insulation film on the back of
the engine should never be removed.
2.
LED WALL SCONCE KIT
RETROFIT KIT INSTALLATION MANUAL
FOR 12” WALL SCONCE LUMINAIRES
1/6/22 INS-AC-LN11-WS, Rev C
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 [email protected] www.fulham.com
Installation Instructions subject to change without notice. Page 7 of 7
Place the provided Retrofit Label (C) on the
luminaire back plate in a readily visible
location to anyone attempting to service the
luminaire. See Figure 4.
Completed retrofit should look like Figure 4.
4.
5.
Figure 4
8.0 WARRANTY
Connecting Power to the Retrofit Kit:
1)
2)
3)
Connect the Copper wire (Ground) from the luminaire to the Ground that is being fed by the power source.
Connect these two wires by using a wire connector with a minimum 18AWG rating.
Connect the white wire (Neutral) from the DirectAC Engine to the Neutral being fed by the power source. Connect
these two wires by using a wire connector with a minimum 18AWG rating.
Connect the Black wire (Line) from DirectAC Engine to the Line being fed by the power source. Connect these two
wires by using a wire connector with a minimum 18AWG rating.
Figure 5
Luminaire is now ready to be installed.
Please see below for instructions on
connecting line voltage to the luminaire.
Re-attach and secure the lens once
installation is completed, retrofit should
look like Figure 5.
6.
7.0 RETROFIT KIT ASSEMBLY
Please refer to Linear AC Engine kit spec sheet for warranty information
LED WALL SCONCE KIT
RETROFIT KIT INSTALLATION MANUAL
FOR 12” WALL SCONCE LUMINAIRES
This luminaire has been modified and can no
longer operate the originally intended lamp.
Ce luminaire a été modifié et ne peut plus
utiliser la lampe prévue à l'origine.
1/6/22 INS-AC-LN11-WS, Rev C
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

VIZION FULHAM VJTUNV015LNxyyB11 12 Inch Wall Sconce Luminaire Manuel utilisateur

Taper
Manuel utilisateur