Vizio TJTUNV010ACxxxB Manuel utilisateur

Vizio
Marque
Vizio
Modèle
TJTUNV010ACxxxB
Taper
Manuel utilisateur
INSTALLATION INSTRUCTIONS
DirectAC Universal Voltage (120-277V) Engine Refrofit Kit
LED LIGHT ENGINE APPLICATION PROGRAM
MANUAL FOR LED LIGHT ENGINE KIT INSTALLATION
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 [email protected] www.fulham.com
Installation Instructions subject to change without notice.
TJTUNV010ACxxxB
Page 1 of 5
Reference spec sheet for full part numbers
UNV Direct AC Kit, Rev B
1/6/22
1.0 INSTALLATION WARNINGS
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 [email protected] www.fulham.com
Installation Instructions subject to change without notice.
1.0 AVERTISSEMENTS D'INSTALLATION
1.
2.
3.
4.
5.
6.
7.
8.
"THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND HAZARDS INVOLVED.”
“WARNING - Risk of fire or electric shock. LED Retrofit kit installation requires knowledge of luminaires
electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.”
“WARNING - Risk of fire or electric shock. Install this kit only in the luminaires that has the construction features
and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not
exceed the input rating of the luminaire.”
“WARNING - To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other
sharp objects.”
“WARNING –Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling
for installation of LED retrofit kit. Check for enclosed wiring and components."
"CAUTION – RISK OF FIRE. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTOR."
“THE RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY
OF THE COMBINATION SHALL BE DETERMINED BY THE AUTHORITIES HAVING JURISDICTION.”
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
1.
2.
3.
4.
5.
6.
7.
8.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION PERTINENT, PAR UNE
PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES
INHÉRENTS.
AVERTISSEMENT - Risque d’incendie ou de choc électrique. L’installation de ce nécessaire de modernisation
exige une personne familière avec la construction et le fonctionnement du système électrique du luminaire et
des risques associés. Toute personne qui n’est pas qualifiée ne doit faire aucune tentative d’installation et doit
contacter une personne qualifiée.
AVERTISSEMENT - Risque d’incendie ou de choc électrique. N’installer ce nécessaire que dans les luminaires
don't les caractéristiques de construction et les dimensions sont conforme à celles illustrées dans les photos
et/ou les dessins et dont la puissance d’entrée nominale du nécessaire de modernisation ne dépasse pas celle
du luminaire.
AVERTISSEMENT - Afin de prévenir l’endommagement ou l’abrasion des câbles, éviter tout contact entre ces
derniers et le bord d’un objet tranchant tel qu’une tôle.
“AVERTISSEMENT -Risk d'incendie ou de choc électrique. Le câblage du luminaire et les pièces électriques
peuvent être endommagés lors du forage pour l'installation d'un kit de reconditionnement LED. Vérifiez le
câblage et les composants inclus. "
ATTENTION – RISQUE D'INCENDIE, CONSULTER UN ÉLECTRICIEN QUALIFIÉ POUR VOUS
ASSURER QUE LES CONDUCTEURS DE LA DÉRIVATION SONT ADÉQUATS.
LE NÉCESSAIRE DE MODERNISATION EST ACCEPTÉ À TITRE DE COMPOSANT D’UN LUMINAIRE
LORSQUE LA PERTINENCE DE LA COMBINAISON DOIT ËTRE DÉTERMINÉE PAR PAR LES
AUTORITÉS COMPÉTENTES.
Ne faites pas ou ne modifiez aucun trou ouvert dans une enceinte de câblage ou de composants électriques
pendant l'installation du kit
LED LIGHT ENGINE APPLICATION PROGRAM
MANUAL FOR LED LIGHT ENGINE KIT INSTALLATION
Page 2 of 5
UNV Direct AC Kit, Rev B
1/6/22
Retrofit kit components will be provided as listed below:
Remove all the original luminaire parts, hardware, lamp, ballast and socket in order to begin the retrofit.
Original luminaire diffuser and original ground wire will need to be kept for this retrofit.
This Universal Voltage DirectAC Engine Kit can be retrofitted into any surface wall or ceiling luminaire with a similar
shape and diameter/height greater or equal to the minimum dimensions described above, or volume greater or equal
to 73.87 cubic inches.
4.0 RECOMMENDED TOOLS (Not Included)
3.0 RETROFIT KIT COMPONENTS
2.0 ORIGINAL LUMINAIRE DIMENSIONS
Original Luminaire Minimum Luminaire
Dimensions
Power Drill W/ Philips Bit
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 [email protected] www.fulham.com
Installation Instructions subject to change without notice.
1.25”
7.69”
7.69”
Direct AC LED Engine Mounting Hardware Input Power Connector Retrofit Label
LED LIGHT ENGINE APPLICATION PROGRAM
MANUAL FOR LED LIGHT ENGINE KIT INSTALLATION
Page 3 of 5
This luminaire has been modified to
operate LED lamps. Do not attempt
to install or operate incandescent /
fluorescent lamps in this luminaire.
Mfr: RLR Industries - Model: Picture Frame Sconce
UNV Direct AC Kit, Rev B
1/6/22
5.0 RETROFIT KIT DESCRIPTION
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 [email protected] www.fulham.com
Installation Instructions subject to change without notice.
B
A
CThis luminaire has been modified to
operate LED lamps. Do not attempt
to install or operate incandescent /
fluorescent lamps in this luminaire.
D
TJTUNV010ACxxxB
LED LIGHT ENGINE APPLICATION PROGRAM
MANUAL FOR LED LIGHT ENGINE KIT INSTALLATION
Page 4 of 5
ITEM
DESCRIPTION
QTY
A.
Direct AC LED Engine
1
B.
6-20 X 5/8” Flat Head Self Drilling Screws
4
C.
Input Power Connector
1
D.
Retrofit Label
1
UNV Direct AC Kit, Rev B
1/6/22
6.0 RETROFIT KIT ASSEMBLY
7.0 WARRANTY
Please refer to DirectAC Engine kit spec sheet for warranty information
Figure 4
Figure 1
Figure 3
Figure 2
Figure 6
Connecting Power to the DirectAC Engine:
1)
2)
3)
Connect the green wire (Ground) from the luminaire to the Ground that is being fed by the power source. Connect
these two wires by using a wire connector with a minimum 18AWG rating.
Connect the white wire (Neutral) from the DirectAC Engine to the Neutral being fed by the power source. Connect
these two wires by using a wire connector with a minimum 18AWG rating.
Connect the Black wire (Line) from DirectAC Engine to the Line being fed by the power source. Connect these two
wires by using a wire connector with a minimum 18AWG rating.
Fulham Co. Inc.: 12705 South Van Ness Ave., Hawthorne, CA 90250 · Telephone: 1-323-779-2980 · Fax: 1-323-754-9060 [email protected] www.fulham.com
Installation Instructions subject to change without notice.
Figure 5
Start by removing the original lamp, ballast
and socket from the luminaire see figure 1.
NOTE: The original luminare ground wire
will need to be kept for this retrofit.
Center the DirectAC Engine (A) in the
luminaire so that the line voltage cables
are aligned with one of the holes found in
the luminaire plate. See figure 2.
NOTE: LED Engine must make direct
contact with the back plate when installed
in order to provide sufficient heat sinking to
properly manage thermals for safety and
warranty purposes. The insulation film on
the back of the engine should never be
removed.
Use the supplied self-drilling screws (B)
to attach the DirectAC Engine (A) to the
luminaire plate. See figure 3.
Feed line voltage cables from the DirectAC
Engine (A) through one of the holes found
in the luminaire. See figure 4.
Place the provided Retrofit Label (E) on
the outer areas of the luminaire where
DirectAC Engine (A) was just installed.
Labels must be clearly visible and should
not be obscured by line voltage cables.
See figure 5.
Completed assembly should look like
figure 5.
Luminaire is now ready to be installed.
Please see below for instructions on
connecting line voltage to the luminaire.
Re-attach and secure the lens once
installation is completed, retrofit should
look like figure 6.
1.
2.
3.
4.
5.
6.
7.
8. This luminaire has been modified to
operate LED lamps. Do not attempt
to install or operate incandescent /
fluorescent lamps in this luminaire.
LED LIGHT ENGINE APPLICATION PROGRAM
MANUAL FOR LED LIGHT ENGINE KIT INSTALLATION
Page 5 of 5
UNV Direct AC Kit, Rev B
1/6/22
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Vizio TJTUNV010ACxxxB Manuel utilisateur

Vizio
Marque
Vizio
Modèle
TJTUNV010ACxxxB
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents