Wacker Neuson CRT48-35V Manuel utilisateur

Operator’s Manual

Notice d'emploi

Ride-On Trowel

Truelles auto portées

CRT48-35V

CRT48-35L

CRT48-57K

Type CRT48-35V, CRT48-35L, CRT48-57K

Document 5100022505

Date

0616

Version

03

Language EN-FR

5100022505

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

CRT48 Foreword

wc_tx004191gb_FM10.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine

documentation

■ From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

■ Keep a copy of the Operator’s Manual with the machine at all times.

■ For spare parts information, please see your Wacker Neuson Dealer, or visit the

Wacker Neuson website at http://www.wackerneuson.com/.

■ When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Machine Item Number

CRT48-35V 5000620112, 5000620807

CRT48-35L 5000620113, 5000620806

CRT48-57K 5100018892

wc_gr013202

Serial Number:

Foreword CRT48

4 wc_tx004191gb_FM10.fm

Expectations

for

information in

this manual

■ This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

■ Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

■ The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change any

portion of this information without notice.

■ The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

■ Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

■ Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

■ Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

■ Serious injury hazards to the operator and persons in the work area

■ Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

2016-CE-CRT48MS-en_FM10.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

CRT48-35L, CRT48-35V

Trowel

To smooth and finish semi-cured concrete

5000620806, 5000620807

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2014/30/EU, EN12649

Authorized Person for Technical Documents

Leo Goeschka, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41,

80809 München

Menomonee Falls, WI, USA, 27.05.16

Original Declaration of Conformity

Keith Herr

Vice President and Managing Director

For Wacker Neuson

Scott Grahl

Manager, Product Engineering

For Wacker Neuson

Jeff Volden

Director, Product Engineering

For Wacker Neuson

6

Table of Contents

CRT48

wc_bo5100022491_03_FM10T

7

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 11

1.1 Signal Words Used in this Manual ..................................................... 11

1.2 Machine Description and Intended Use ............................................. 12

1.3 Safety Guidelines for Operating the Machine ..................................... 13

1.4 Service Safety .................................................................................... 15

1.5 Operator Safety while Using Internal Combustion Engines ............... 17

1.6 Safety Guidelines for Lifting the Machine ........................................... 18

2 Labels 20

2.1 Label Locations .................................................................................. 20

2.2 Label Meanings .................................................................................. 21

3 Lifting and Transporting 30

3.1 Lifting the Machine ............................................................................. 30

3.2 Preparing the Machine for Transport on a Truck or Trailer ................ 31

4 Operation 33

4.1 Preparing the Machine for First Use ................................................... 33

4.2 Position of the Operator ..................................................................... 33

4.3 Machine Components ........................................................................ 34

4.4 Machine Components Descriptions .................................................... 35

4.5 Recommended Fuel—Gasoline ......................................................... 36

4.6 Recommended Fuel—Diesel ............................................................. 36

4.7 Refueling the Machine ........................................................................ 37

4.8 Break-In Period .................................................................................. 38

4.9 Before Starting ................................................................................... 38

4.10 Starting, Steering, Operating,

and Stopping the Machine (Vanguard) ............................................... 39

4.11 Starting, Steering, Operating, and Stopping the Machine (Kohler) .... 41

4.12 Starting, Steering, Operating, and Stopping the Machine (Kubota) ... 43

4.13 Adjusting the Pitch .............................................................................. 45

4.14 Emergency Shutdown Procedure ....................................................... 46

Table of Contents

CRT48

8

5 General Maintenance 47

5.1 Maintaining the Emission Control System ...........................................47

5.2 Periodic Maintenance Schedule ..........................................................48

5.3 Maintaining the Gearboxes .................................................................49

5.4 Adjusting the Blade Arms ....................................................................51

5.5 Lubricate the Trowel Arms ..................................................................53

5.6 Mounting Float Pans ...........................................................................54

5.7 Replacing the Drive Belt ......................................................................56

5.8 Installing or Changing the Blades ........................................................58

5.9 Cleaning the Machine ..........................................................................60

5.10 Storage ................................................................................................61

5.11 Machine Disposal / Decommissioning .................................................62

6 Engine Maintenance: Kohler 63

7 Engine Maintenance: Vanguard 68

8 Engine Maintenance: Kubota 70

9 Troubleshooting 75

10 Technical Data 76

10.1 Engine .................................................................................................76

10.2 Trowel ..................................................................................................77

10.3 Sound Measurements .........................................................................78

10.4 Vibration Measurements .....................................................................78

10.5 Dimensions ..........................................................................................79

11 Emission Control Systems Information

and Warranty—Diesel 81

11.1 Emission Control System Background Information .............................81

11.2 Limited Defect Warranty for Wacker Neuson

Emission Control Systems ..................................................................82

wc_bo5100022491_03_FM10T

Table of Contents

CRT48

wc_bo5100022491_03_FM10T

9

12 Emission Control Systems Information

and Warranty—Gasoline 87

12.1 Emission Control System Background Information ............................ 87

12.2 Limited Defect Warranty for Wacker Neuson

Emission Control Systems ................................................................. 88

13 AEM Safety Manual 93

14 Schematics 107

14.1 Electrical Schematic—CRT48-35V .................................................. 108

14.2 Electrical Schematic Components—CRT48-35V ............................. 109

14.3 Electrical Schematic—CRT48-35L ................................................... 110

14.4 Electrical Schematic Components—CRT48-35L ............................. 111

14.5 Electrical Schematic—CRT48-57K .................................................. 112

14.6 Electrical Schematic Components—CRT48-57K ............................. 113

14.7 Fuse/Relay Box Layout .................................................................... 113

Table of Contents

CRT48

10

wc_si000969gb_FM10.fm

11

CRT48 Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

► Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

► To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

► To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

► To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000969gb_FM10.fm

12

Safety Information CRT48

1.2 Machine Description and Intended Use

This machine is a ride-on concrete finishing trowel. The Wacker Neuson Ride-On

Trowel consists of a frame onto which are mounted a gasoline or diesel engine, a fuel

tank, a water tank, two gearboxes joined by a drive shaft, and an operator’s platform

with controls and a seat. A set of metal blades is connected to each gearbox. A ring

guard surrounds the blades. The engine rotates the blades via the gearboxes and a

clutch mechanism. The rotating blades ride on the surface of curing concrete, creating

a smooth finish. The operator, who sits on the operator’s platform, uses the controls and

the throttle pedal to control speed and direction of the machine.

This machine is intended to be used for floating and burnishing curing concrete.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine damage

caused by misuse is not covered under warranty.

The following are some examples of misuse:

■ Using the machine as a ladder, support, or work surface

■ Using the machine to carry or transport passengers or equipment

■ Using the machine to finish inappropriate materials such as slurries, sealers, or

epoxy finishes

■ Operating the machine outside of factory specifications

■ Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global safety

standards. It has been carefully engineered to eliminate hazards as far as practicable

and to increase operator safety through protective guards and labeling. However, some

risks may remain even after protective measures have been taken. They are called

residual risks. On this machine, they may include exposure to:

■ Heat, noise, exhaust, and carbon monoxide from the engine

■ Chemical burns from the curing concrete

■ Fire hazards from improper refueling techniques

■ Fuel and its fumes, fuel spillage from improper lifting technique

■ Personal injury from improper lifting techniques

■ Cutting hazards from sharp or worn blades

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_si000969gb_FM10.fm

13

CRT48 Safety Information

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

■ Read and understand the operating instructions contained in all manuals

delivered with the machine.

■ Familiarize yourself with the location and proper use of all controls and safety

devices.

■ Contact Wacker Neuson for additional training if necessary.

When operating this machine:

■ Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

■ have received instruction on how to properly use the machine

■ are familiar with required safety devices

The machine must not be accessed or operated by:

■ children

■ people impaired by alcohol or drugs

Application

area

Be aware of the application area.

■ Keep unauthorized personnel, children, and pets away from the machine.

■ Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

■ Identify whether special hazards exist in the application area, such as toxic

gases or unstable ground conditions, and take appropriate action to eliminate

the special hazards before using the machine.

Be aware of the application area.

■ Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

■ All safety devices and guards are in place and in working order.

■ All controls operate correctly.

■ The machine is set up correctly according to the instructions in the Operator’s

Manual.

■ The machine is clean.

■ The machine’s labels are legible.

To ensure safe operation of the machine:

■ Do not operate the machine if any safety devices or guards are missing or

inoperative.

■ Do not modify or defeat the safety devices.

■ Only use accessories or attachments that are approved by Wacker Neuson.

wc_si000969gb_FM10.fm

14

Safety Information CRT48

Safe

operating

practices

When operating this machine:

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

When operating this machine:

■ Do not operate a machine in need of repair.

■ Do not consume the operating fluids used in this machine. Depending on your

machine model, these operating fluids may include water, wetting agents, fuel

(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic fluid,

heat transfer fluid (propylene glycol with additives), battery acid, or grease.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

After Use

■ Stop the engine when the machine is not being operated.

■ Close the fuel valve on engines equipped with one when machine is not being

operated.

■ Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

■ Store the machine properly when it is not being used. The machine should be

stored in a clean, dry location out of the reach of children.

wc_si000969gb_FM10.fm

15

CRT48 Safety Information

1.4 Service Safety

Service

training

Before servicing or maintaining the machine:

■ Read and understand the instructions contained in all manuals delivered with

the machine.

■ Familiarize yourself with the location and proper use of all controls and safety

devices.

■ Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

■ Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

■ Do not allow improperly trained people to service or maintain the machine.

Personnel servicing or maintaining the machine must be familiar with the

associated potential risks and hazards.

Precautions

When servicing or maintaining the machine:

■ Read and understand the service procedures before performing any service to

the machine.

■ All adjustments and repairs must be completed before operating the machine.

Do not operate the machine with a known problem or deficiency.

■ All repairs and adjustments shall be completed by a qualified technician.

■ Turn off the machine before performing maintenance or making repairs.

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

■ Re-install the safety devices and guards after repair and maintenance

procedures are complete.

Machine

modifications

When servicing or maintaining the machine:

■ Use only accessories/attachments that are approved by Wacker Neuson.

When servicing or maintaining the machine:

■ Do not defeat safety devices.

■ Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing

parts and

labels

■ Replace worn or damaged components.

■ Replace all missing and hard-to-read labels.

■ When replacing electrical components, use components that are identical in

rating and performance to the original components.

■ When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

wc_si000969gb_FM10.fm

16

Safety Information CRT48

Cleaning

When cleaning and servicing the machine:

■ Keep the machine clean and free of debris such as leaves, paper, cartons, etc.

■ Keep the labels legible.

When cleaning the machine:

■ Do not clean the machine while it is running.

■ Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

In addition, before servicing or maintaining the machine:

■ Tie back long hair.

■ Remove all jewelry (including rings).

wc_si000969gb_FM10.fm

17

CRT48 Safety Information

1.5 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

■ Keep the area around the exhaust pipe free of flammable materials.

■ Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

When running the engine:

■ Do not smoke while operating the machine.

■ Do not run the engine near sparks or open flames.

■ Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

■ Do not operate a machine when its fuel cap is loose or missing.

■ Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

■ Clean up any spilled fuel immediately.

■ Refill the fuel tank in a well-ventilated area.

■ Re-install the fuel tank cap after refueling.

■ Do not smoke.

■ Do not refuel a hot or running engine.

■ Do not refuel the engine near sparks or open flames.

■ Use suitable tools for refueling (for example, a fuel hose or a funnel).

■ Do not refuel if the machine is positioned in a truck fitted with a plastic bed liner.

Static electricity can ignite the fuel or fuel vapors.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

► Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

► NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

wc_si000969gb_FM10.fm

18

Safety Information CRT48

1.6 Safety Guidelines for Lifting the Machine

When lifting the machine:

■ Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any

other type of lifting device used is attached securely and has enough weight-

bearing capacity to lift or hold the machine safely. See section Technical Data

for machine weight.

■ Remain aware of the location of other people when lifting the machine.

■ Only use the lifting points and tie-downs described in the Operator’s Manual.

■ Make sure the transporting vehicle has sufficient load capacity and platform size

to safely transport the machine.

To reduce the possibility of injury:

■ Do not stand under the machine while it is being lifted or moved.

■ Do not get onto the machine while it is being lifted or moved.

wc_si000969gb_FM10.fm

19

CRT48 Safety Information

Notes

wc_si000970gb_FM10.fm

20

Labels CRT48

2 Labels

2.1 Label Locations

wc_gr013222

A

B

G

L

P

U

K

AA

H

EE

C

D

E

Q

R

S

T

M

F

Q

K

P

L

Z

X

G

FF

G

Z

N

L

F

Y

DD

W

J

CC

V

BB

La page charge ...

Wacker Neuson CRT48-35V Manuel utilisateur

Ce manuel convient également à

Wacker Neuson CRT48-35V Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents