Hotpoint HDA3600R00CC Guide d'installation

Marque: Hotpoint

Modèle: HDA3600R00CC

Catégorie: Lave-vaisselle

Taper: Guide d'installation

(]_[Z" F" - . . o' I_,,.......i! _,. °_,, i

,;......... ,,y o_<,. I (_;_ C');( If I{.]t.l,<::;_>.(_

Appliances

Installation Instructions

Built-In Dishwasher

Ifyou havequestions,call800.GE.CARES(800.432.2737)or visitourwebsiteat:GEAppliances.com

In Canada,call 1.800.561.3344orvisitwww.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completelg and

carefullg.

lMPORTANT- Observe all governing codes

and ordinances.

• Note to Installer- Be sure to leave these

instructions for the consumer and local inspector's

use.

• Note to Consumer - Keep these instructions with

your Owner's Manual for future reference.

• Skill Level - Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills.

Proper installation is the responsibility of

the installer. Product failure due to improper

installation is not covered under the GE

Appliance Warranty. See warranty information.

• Completion Time - 1 to 3 Hours. New installations

require more time than replacement installations.

IMPORTANT-The dishwasher MUST be

installed to allow for future removal from the

enclosure if service is required.

If gou received a damaged dishwasher, gou should

immediatelg contact gout dealer or builder.

Optional Accessories - Seethe Owner's Manual for

available custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS

shown throughout these instructions. While

performing installations described in this booklet,

gloves and safetg glasses should be worn.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

206C1559P195 31-30255 07-09 .JR

PARTS SUPPLIED IN INSTALLATION

PACKAGE:

[] Two 8-18 x 5/8" Phillips-head wood screws

[] Junction box cover and #10 hex head

screw

[] Drain hose (78" long)and hose clamp

[] Cord protector (Power Cord Models Only)

[] Conversion leads (Power Cord Models Only)

[] Literature, product samples and/or

coupons

Screw Kit

Phillips-Head

Wood Screws

5/8" long

#10

He× Head

Junction Box Screw

1/2" long

Junction Box Cover

78" Drain Hose

Hose Clamp

Cord Protector

{Power Cord Models Only)

Conversion Leads

{Power Cord Models Onlg)

MATERIALS YOU WILL NEED:

[] WX09X70910 power cord if applicable to

your installation

[] UL-Listed wire nuts (3)

[] Thread seal tape

[] 90° elbow, ferrule and compression nut-

(3/8" NPT external thread on one end and

opposite end sized to fit water supply)

[] GPF65 Side-mount bracket kit for use with

granite countertops

FOR NEW INSTALLATIONS:

[] Electrical cable

[] Water line-S/8" minimum copper tubing

[] Strain relief for electrical connection

[] Hand shut-off valve (recommended)

[] Air gap for drain hose, if required

[] Waste tee for house plumbing, if

applicable

[] GPF10S drain hose (10' long), if needed

[] Screw-type hose clamps

TOOLS YOU WILL NEED:

[] Safety glasses

[] 1/4" and 5/16" nutdrivers

[] Flashlight

[] Gloves

[] Adjustable wrench (6")

[] Phillips-head screwdriver

[] Measuring tape

[] Level

[] Carpenter's square

[] Bucket to catch water when flushing

water line

[] Tubing cutter

[] 15/16" socket wrench

FOR NEW INSTALLATIONS:

[] Hole saw set

[] Drill and appropriate bits

Electrical Cable

or WR09×70910

Power Cord

3 Wire Nuts

Thread

Strain Relief Seal Tape

Shut-Off

Valve

GPF65 Side-Mount

Bracket Kit Air

Gap

Optional 10'

Drain Hose

Waste Tee

GPFIOS

Safety Glasses

1/4" and 5/16" Nutdrivers

Flashlight

Adjustab e _ Phillips-Head

Wrench Screwdriver

Level

TUbing

utter

Measuring Tape

Hot Water Line-3/8"

Minimum Copper

Tubing

90° Elbow, Ferrule and

Compression Nut

Screw-Type

Hose Clamps

Bucket

Hole Saw Set

Carpenter's

Square

1S/16"

Socket Wrench

installation Preparation - Enclosure

PREPARE DISHWASHER ENCLOSURE

To reduce the risk of shock, fire, or injurg

to persons, the installer must ensure that

the dishwasher is completelg enclosed at

the time of installation.

Para redudr el riesgo de choque, incendio

o lesi6na personas, el instalador se

debe cerdorar de que la lavadora est_

completamente cerrada en el momento

de la instalad6n.

, The rough cabinet opening must have a minimum

width and depth of 24" and height of 34-1/2" _+1/4"

from the floor to the underside of the countertop.

, The back wall should be free of pipes or wires.

, Adjacent cabinets should be square and plumb to

ensure a good fit. Refer to Figure A.

, For a corner installation, allow 2" minimum

clearance between the dishwasher and the

adjacent wall.

, Provide at least 27" in front of the dishwasher to

allow the dishwasher door to open fullg. Refer to

Figure B.

34-1/2"_+ 1/4"

Underside of

Countertop

to Floor

This Wall Area

must be Free of

Pipes or wires

, The dishwasher must be installed no more than

10 feet from sink for proper drainage.

, The dishwasher must be fullg enclosed on the top,

sides and back.

, The dishwasher must not support any part of the

enclosu re.

1' Countertop

DishwosheI

Clearances:

In a corner installation, provide

at least 2" clearance between

[_ the dishwasher and the adjacent

i cabinet, wall or other appliance.

Provide at least 27" of clearance

in front of the dishwasher.

27"Minimum

Figure 8

Squore

and

Plumb

Figure A

Floor MUST

be Even with

Room Floor

Plumbing and Electric Service

Must Enter Shaded Area

• Make sure the floor is level inside the opening and

even with the finished floor of the kitchen. This will

facilitate removal of the dishwasher at a later date

for service, if needed.

Installation Preparation - Drain

PREPARE DRAIN PLUMBING

Drain Requirements

• Follow local codes and ordinances.

• Drain hose must not exceed 10 feet in length.

, A high drain loop or air gap is required. See below.

Drain Method

The type of drain installation depends on the

following:

• Do local codes or ordinances require an air gap?

• Is waste tee less than 18" above the floor?

If the answer to either question is YES,an air gap

(Method 1) must be used. If both answers are NO,

either an air gap or a high drain loop (Method 2)

may be used.

Special consideration for a dishwasher installed

on a pedestal

If the dishwasher is installed on an elevated

platform, a high drain loop of at least 32" above the

platform must be provided in addition to the air gap

requirement determined above. This is necessary for

proper drain performance.

CAUTION

An air gap MUST BE USED if the drain hose is connected to

waste tee or disposer lower than 18" above the floor level.

Failure to provide the proper drain connection height with

an air gap or 32" minimum, high drain loop will result in

improper draining of the dishwasher, which mag cause

damage.

PRECAUCION

SE DEBE USAR un espado de aire si la manguera

de drenaje se conecta a la T de desechos o al triturador

menos de 18" por endma del nivel del piso. No disponer

la altura correcta de la conexi6n del drenaje con

un espacio de aire o 32" de minima, una curva alta

de drenaje resultar_ en un drenaje incorrecto

de la lavadora, Io que pude causar da_os.

METHOD 1 - Air Gap with Waste Tee or Disposer

__ ra

Waste Tee Installation

Figure C

Disposer Installation

METHOD 2- High Drain Loop with Waste Tee

or Disposer

Provide a method to attach the drain hose to the

underside of countertop. Attachment will be made in

a later step.

Waste Tee Installation

Figure D

Disposer Installation

Install waste tee or disposer and the air gap

according to the manufacturer's instructions.

Cabinet Preparation

Drill a 1-1/2" diameter hole in the cabinet wall within

the shaded area shown in Figure A for the drain

hose. Make sure there are no sharp edges. The drain

hose will be passed through this hole and connected

to the drain in a later step.

IMPORTANT- When

f===y

connecting the drain line to a

disposer, check to be sure that

L:f

drain plug has been removed.

Dishwasher will not drain if

plug is left in place.

4 Remove

Drain

Plug

Installation Preparation - Electrical Supply

PREPARE ELECTRICAL WIRING

FOR PERSONAL SAFETY: Remove house fuse

or open circuit breaker before beginning

installation. Do not use an extension cord or

adapter plug with this appliance.

PARA SEGURIDAD PERSONAL: Retire el

fusible de la casa o abra el interruptor de

circuitos antes de empezar la instolaci6n.

No use un cable de extensi6n o enchufe

adaptador con este aparato.

Electrical Requirements

• This appliance must be supplied with 120V, 60 Hz.,

and connected to an individual properlg grounded

branch circuit, protected bg a 15- or 20-ampere

circuit breaker or time-delag fuse.

• Wiring must be 2 wire with ground.

• If the electrical supplg does not meet the above

requirements, call a licensed electrician before

proceeding.

Grounding Instructions - Permanent Connection

This appliance must be connected to a grounded-

metal, permanent wiring sgstem, or an equipment-

grounding conductor must be run with the circuit

conductors and be connected to the equipment-

grounding terminal or lead on the appliance.

Grounding Instructions - Power Cord Models

This appliance must be grounded. In the event of a

malfunction or breakdown, grounding will reduce

the risk of electric shock bg providing a path of

least resistance for electric current. This appliance

is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug

must be plugged into an appropriate outlet that is

installed and grounded in accordance with all local

codes and ordinances.

The improper connection of the equipment-

grounding conductor can result in electric

shock. Check with a qualified electrician or

service representative if gou are in doubt that

the appliance is properlg grounded,

Do not modifg the plug provided with the

appliance; if it will not fit the outlet° have

a proper outlet installed bg a qualified

technician.

_La conexi6n incorrecta del conductor

de conexi6n a tierra del equipo puede

resuitar en choque el_ctrico. Consulte con

un electricista calificado o representante

de servicio si tiene dudas de la conexi6n

a tierra del aparato. No modifique el

enchufe qua se suministra con el aparato;

si no colza en el tomacorrientes0 haga

qua un t_cnico calificado le instale un

tomacorrientes adecuado.

,,f- Alternate ]'\

// I

I Receptacle ij \\

_,, " Location

Cabinet

Figure E

White

Cabinet Preparation and Wire Routing

, The wiring mag enter the opening from either side,

rear or floor within the shaded area illustrated

above in Figure Eand defined in Figure A.

• Cut a 2-1/2" maximum diameter hole to insert the

electrical cable. Permanent wiring connections

mag pass through the same hole as the drain

hose and hot water line, if convenient. Hole edges

must be smooth and rounded, if the cabinet wall is

metal, the hole edge must be covered with a cord

protector.

NOTE: Power cords with plug must pass through a

separate hole.

Protector

(Provided

with Power

Cord Hodels Onlg)

Hole Diameter

1-1/2" Haximum

Electrical Connection to Dishwasher

Electrical connection is on the right front of

dishwasher.

, For permanent connections, the cable must be

routed as shown in Figure E.The cable must extend

a minimum of 24" from the rear wall.

, For power cord connections, install a 3-prong

grounding-tgpe receptacle in the adjacent cabinet

rear wall, between 6" and 18" from the opening, 6"

to 18" above the floor as shown in Figure E.

Installation Preparation - Hot Water Supply

PREPARE HOT WATER SUPPLY

Hot Water Line

,, The line may enter from either side, rear or floor

within the shaded area shown in Figure F.

,,The line may pass through the same hole as the

electrical cable and drain hose, or cut an additional

1-1/2" diameter hole to accommodate the water

line. If a power cord with plug is used, the water line

must not pass through the power cord hole.

Figure F

CAUTION

The hot water supply line pressure must be at least 20 PSI.

Lower pressures could cause the water valve to leak and

cause water damage.

PRECAUCI6N

La Jineade presi6n del suministro de ague caliente debe

ser al menos 20 PSL Presiones inferiores podrian causer

que la v6lvula del ague gotee y causer da6os por ague.

Water Line Connection

• Turn off the water supplg.

,, Install a hand shut-off valve in an accessible

location, such as under the sink. (Optional, but

stronglg recommended and mag be required bg

local codes.)

,,The water connection is on the left side of the

dishwasher. Install the hot water inlet line, using

3/8" or larger copper tubing. Route the line as

shown in Figure Fand extend forward at least 19"

from rear wall.

,, Adjust the water heater to deliver water between

120% and 150°R

• Flush water line to clean out debris. Use a bucket

to catch water and debris.

• The hot water supplg line pressure must be

between 20 and 120 PSI.

Dishwasher Installation

CAUTION

Do not remove the wood base until you are ready to

install the dishwasher. The dishwasher will tip over

when the door is opened if the base is removed.

PRECAUCION

No retire la base de madera hasta que est_ listo para

instalar la lavadora de platos. Cuando la puerta seabra,

la lavadora de platos se inclinar6 si la base se retira.

STEP 1:PREPARATION

Locate the items in the installation package and set

them aside for use in the listed steps.

, Screw kit- Steps 5 or 16 and 13

, Junction box cover- Steps 5 or 16

, Drain hose and drain hose clamp- Step 7

, Owners' Manual- Steps 18 and 21

, Product Samples and/or coupons- Step 21

, Conversion leads (Factorg-equipped power cord

models onlg) - Appendix

STEP 2:CHECK DOOR BALANCE

• With the dishwasher on the wood base, check the

door balance bg opening and closing the door.

, The door is properlg balanced if it gentlg drops

from a 1/2 open position and does not rise from

the full open position.

, If necessarg, increase or decrease tension as

shown. Latch the door and adjust springs to

correct ba la nce.

Link fullg seated

in hinge arm

Insert Hook Throu,

Hole from Inside of Frame

Figure G

Tip: Avoid service calls for door balance problems.

Make sure the spring end is fullg engaged in a

frame hole and the spring link is fullg seated in the

hinge arm.

STEP 3: REMOVE WOOD BASE

IMPORTANT- Donotkick offwood base!

Damage will occur.

• Move the dishwasher close to the installation

location and lag it on its back.

, Remove the four leveling

legs from the underside of

the wood base

with a 15/16"

socket wrench.

, Remove and

discard wood

base.

Figure H

• Screw leveling legs back into the dishwasher

frame, approximatelg 3/4" from the frame, as

shown.

STEP 4: REMOVE ACCESS PANEL

AND TOEKICK

The top mounting holes in the access panel are

slotted.

, Remove the lower two 10-16 x 3/8" sheet metal

screws. Do not remove the two top 8-32 x 1/4"

machine thread screws.

, Slide the access panel to the left as far as it will go.

, Gentlg pull the access panel forward to remove

it from the top screws.

Set access panel, toekick and screws aside for use

in Step 20.

Tip: Prevent

tub damage.

Remove onlg

the 3/8" sheet

metal screws

in this step.

This will help

prevent a mix-

up with the

1/4" machine

thread screws

in Step 20.

Do not remove 1//4"

machine-thread screws

in this step

Remove two

3/8" Sheet Metal

Thread Screws

Figure I

Dishwasher Installation

STEP 5: INSTALL POWER CORD

Skip this step if the dishwasher will be

permanentlg connected to the house electrical

sgstem or has a factorg-installed power cord.

In this step you will need the junction box cover and

the #10 x Z/2" hex-head screw from the screw kit set

aside in Step Z.

The power cord and connections must complg

with the National Electrical Code, Section/422 and/

or local codes and ordinances. Maximum power

cord length is 6 feet. Power Cord Kit wxogx70910,

available for purchase from an authorized GE

appliance dealer, meets these requirements.

STEP 6: INSTALL 90° ELBOW

• Wrap a 90° elbow with thread seal tape.

• Thead the 90° elbow into the water valve.

, Do not overtighten the elbow; water valve bracket

could bend or the valve fitting could break.

, Position the end of the elbow to face the rear

of the dishwasher.

90°

Tape

Valve

Bracket

Figure J

Junction Ground

Box Bracket

/ ......!,

White

• Install strain relief in the junction box bracket.

, Insert the power cord through the strain relief and

tighten.

, Make sure black, white and green dishwasher

wires are threaded through the small hole in the

junction box bracket.

, Connect power cord white (or ribbed)to

dishwasher white, black (or smooth) to dishwasher

black and ground to dishwasher green wire. Use

UL-listed wire nuts of appropriate size.

, Install junction box cover using the #10 hex-head

screw. Be sure wires are not pinched under the

cover.

Figure K

STEP 7: INSTALL DRAIN HOSE TO

DISHWASHER DRAIN PORT

Skip this step if drain hose has been preinstalled.

In this step you will need the drain hose and clamp

set aside in Step 1.

IMPORTANT- Prevent drain hose damage

and possible leaks. Be careful not to nick or cut

the drain hose.

, Route the small end of the drain hose from the left

side of the dishwasher through the strain relief

attached to the dishwasher frame and toward

the center of the dishwasher as shown in Figures

Land M.

, Place the hose clamp over the small end of the

drain hose.

, Push the small end of the drain hose over the drain

port on the collection chamber, making sure it is

fully seated against the hose stop.

, Tighten the hose clamp to at least 15 inch-pounds

of torque.

Dishwasher Installation

Figure L

Note: The drain hose supplied with the dishwasher

is approximately 78" long. If u longer hose is needed,

a 10-foot-long hose may be purchased from an

authorized GEappliance dealer. The 10-foot-long

hose is part number GPFIOS.

\\ _ / ,Strain

Hose Stop

Do not use

this port if

present

STEP 9: INSERT DRAIN HOSE AND POWER

CORD, IF USED, THROUGH CABINET

• Upright the dishwasher and position it n front of

the cabinet opening.

, Insert the drain hose into the hole previously drilled

in the cabinet wall.

, If a power cord is used, guide the end of the cord

through a separate hole cut for the power cord.

The power cord should be routed directly to the rear

of the junction box, avoiding contact with the door

spring and other dishwasher components.

Figure 0

VVater

Figure M

Drain Hose Collection Chamber

Drain Port

Tip: Avoid unnecessarg service charges for drain

issues.

Make sure the drain hose connection is leak-free

and the hose is routed through the strain relief so

it will not kink when the dishwasher is installed into

the cabinet.

STEP 8: POSITION WATER LINE AND

POWER SUPPLY

, Position the water supply line and house wiring on

the floor of the opening to avoid interference with

the base of the dishwasher and components under

the dishwasher.

Line SupplU

Tip: Avoid unnecessarg service charges for no fill,

drain or noise concerns.

Position utility lines so they do not interfere with

anything under or behind the dishwasher.

STEP I0: INSTALL OPTIONAL GPF65 SIDE

MOUNT BRACKETS

Skip this step if the underside of countertop is

wood or woodlike material.

, Purchase and install the GPF65 side-mount

bracket kit if the underside of counter is granite

or a similar material that will not accept wood

screws. The GPF65 kit is available from authorized

GE appliance dealers.

, Refer to Figure P and follow the instructions

included in Side-

the kit.

Tub Frame

Bracket

Attachment

_ Optional Screws

Side-Mount (2 Each

Bracket Kit Figure P Side)Figure N

Dishwasher Installation

STEP 11:SLIDE DISHWASHER INTO CABINET

IM PORTANT - Do not push againstthe front

panel with knees. Damage will occur.

• Grasp the sides of the front panel and slide the

dishwasher into the opening a few inches at

a time. Pull the drain hose and power cord, if

equipped, through the holes in the adjacent

cabinet while sliding the dishwasher into position.

Figure Q

Do not push against

front door panel with

knee. Damage to the

door panel will occur.

STEP 12: POSITION AND LEVEL

DISHWASHER

IMPORTANT- Dishwasher must be level for

proper dish rack operation, wash performance

and door operation. The dishwasher must be

leveled left to right and front to back. This ensures

that the dish racks will not roll in or out on their

own, circulation water will flow to the pump inlet,

and the door will close without hitting the side of

the tub.

, Remove the lower dish rack and place a level on

the door and lower rack track as shown in Figure R.

Check Level

Front to

, Check the tub insulation blanket, if equipped, to

be sure it is smoothly wrapped around the tub.

It should not be "bunched up" and it must not

interfere with the door springs. If the insulation

is "bunched up" or interfering with the springs,

straighten and re-center the blanket prior to sliding

the dishwasher into its final position.

• Make sure the drain hose is not kinked under or

behind the dishwasher.

• Make certain the house wiring, drain line and

water line do not interfere with components under

the dishwasher.

, The dishwasher tub flange should be

approximately 3/4" behind the face of the adjacent

cabinet. Refer to Figure R.

Tip: Avoid unnecessar£1 service charges for panel

damage.

Do not press on the center of panel with hands or

knees when sliding dishwasher into position.

Figure R Side to Side

• Adjust the level of the dishwasher bU individuallLI

turning the four legs on the bottom of the

dishwasher as illustrated in Figure S.

° .

\'L _

Turn Lec /

to Adjust _ FigureS

• The dishwasher is properly leveled when the level

indicator is centered left to right and front to back.

The dishwasher door should close without hitting

the sides of the tub.

• Replace the lower rack.

Tip: Avoid unnecessarg service charges for poor

wash performance and rack operation.

Pull the dish racks half wa Uout. The Ushould remain

stationary. Open and close the door. The door should

fit in the tub opening without hitting the side of the

tub. If the racks roll on their own, or the door hits the

side of the tub, relevel the dishwasher.

Dishwasher Installation

STEP 13: FASTEN DISHWASHER TO

UNDERSIDE OF COUNTERTOP OR SIDES

OF CABINET

In this step gou will need the two 5/8" Phillips-head

wood screws set aside in Step 1.

IMPORTANT - Dishwasher must be centered

in cabinet opening. Interference with cabinets or

countertop will cause leaks and damage to the

door panel and/or control panel.

, If countertop is wood or woodlike material, fasten

the dishwasher to the countertop bg driving the

Phillips head screws through the countertop

brackets and into the countertop.

, If the countertop is granite or similar material,

drive Phillips screws through side mount brackets

and into the adjacent cabinets.

, Make sure screws are driven straight and flush

to prevent interference with door operation and

damage to the control panel. See Figure T.

Countertop

Bracket

Side-Haunt

Brackets (optional)

STEP 14: CONNECT WATER SUPPLY

Connect the water supplg line to the 90° elbow

installed in Step 6.

, Slide the compression nut and then the ferrule over

the end of the water line.

, Insert the water line into the 90° elbow.

, Slide the ferrule against the elbow and secure

with the compression nut.

Figure U

90° Elbow

Hot Water

Supplg Line

Figure T

Tip: Avoid unnecessary service charges for leaks

or control panel damage.

Make sure the dishwasher is centered in the cabinet

and the door opens and closes freely without hitting

the adjacent cabinets. Drive mounting screws

straight and flush.

IMPORTANT - Check to be sure the door

spring does not rub or contact the fill hose or

water supplg line. Test bg opening and closing the

door. Reroute the water supplg lines or slightlg

bend the water valve bracket if a rubbing noise or

interference occurs.

Tip: Avoid unnecessarg service charges for noise

or leaks.

Make sure the door spring does not rub against the

fill hose or water supplg line.

Dishwasher Installation

STEP 15: CONNECT DRAIN LINE

The molded end of the drain hose will fit 5/8"

through l" diameter inlet ports on the air gap, waste

tee or disposer.

, Determine the size of the inlet port

, Cut the drain hose connector on the marked line, if

required, to fit the inlet port.

Figure V

Cutting Line

,n Zs3

IMPORTANT: Do not cut corrugated

portion of hose

. If a longer drain hose is required, and LlOUdid not

purchase the GPF10S drain hose, add up to 42"

length, for a total of 120" (10 feet), to the factorg-

installed hose. Use 5/8" or 7/8" inside diameter

hose and a coupler to connect

the two hose ends.

Secure the

connection

with hose

clamps.

Hose Clamp

Coupler

Figure W

IMPORTANT -Total drain hose length must

not exceed 10 feet for proper drain operation.

• Connect drain line to air gap, waste tee, or disposer

using the previouslg determined method. Secure

the hose with a screw-tLIpe clamp.

Method 1 - Air gap with waste tee or disposer

__-- _ _/___ A

Waste TeeInstallation Disposer Installation

Figure X

Method 2 - "High drain loop" with waste tee

or disposer

Fasten the drain hose to the underside of the

countertop with a hanger.

Waste Tee Installation Disposer Installation

Figure Y

IMPORTANT - When connecting the drain

line to a disposer, check to be sure that the drain

plug has been removed. Dishwasher will not drain

if plug is left in place.

4 Remove

Drain

Plug

Tip: Avoid unnecessary service call charges

for a "no drain" complaint.

Make sure ang excess drain hose has been pulled

through the cabinet opening. This will prevent

excess hose in the dishwasher cavitg from

becoming kinked or crushed bg the dishwasher.

Make sure the disposer plug has been removed if

the drain hose is connected to a disposer.

Dishwasher Installation

STEP 16: CONNECT POWER SUPPLY

If a power cord with plug is already installed,

proceed to Step 17.

If the dishwasher came with a factory-installed

power cord and you want to convert it to a

permanent connection, refer to the instructions on

page 16.

If house wiring is not 2-wire with a ground

wire, a ground must be provided by the

installer.

When house wiring is aluminum, be sure

to use U.L. listed anti-oxidant compound

and aluminum-to-copper connectors.

Siel cableado de la casa no es de 2 cables

con un cable de conexi6n a tierra, el

instalador debe suministrar una conexi6n

a tierra.

Cuando el cableado de la casa es en

aluminio, cerci6rese de usar un compuesto

anti-oxidante aprobado par U.L y un

compuesto de aluminio a cobre.

• Secure house wiring to the back of the junction

box bracket with o strain relief.

. Locate the three dishwasher wires (white, black

and green) with stripped ends. Insert dishwasher

wires through the small hole in the junction box

bracket. Use UL-listed wire nuts of appropriate size

to connect incoming ground to green, white

to white and black to black.

Note: Check that harness leads ore

threaded through small hole in bracket

White

Junction Ground

Box Bracket

Figure Z

STEP 17: INSTALL JUNCTION BOX COVER

If junction box cover is already installed, skip to

Step 18.

In this step you will need the junction box cover and

the #10 hex-head screw from the screw kit set aside

in Step 1.

, Install the junction box cover using the #10 hex-

head screw. Check to be sure that wires ore not

pinched under the cover.

STEP 18: PRETEST CHECKLIST

[] Verify that power is turned off at the source.

[] Open the dishwasher door and remove all foam

and cardboard packaging.

[] Read the Owner's Manual to familiarize yourself

with the operation of the dishwasher.

[] Check to be sure that the wiring is secure under

the dishwasher and not pinched or in contact

with door springs or other dishwasher

components.

[] Check that the door spring does not contact the

water line, fill hose, or adjacent cabinets. See

Steps 13 and 14.

[] Pull lower rack about halfway out. Check to be

sure it does not roll back into dishwasher or

further out. If it does, relevel the dishwasher.

See Step 12.

[] Check to be sure control panel does not touch

adjacent cabinets. If it does, reposition the

dishwasher. See Step 13.

[] Turn on the hot water faucet at the sink to verify

that the water temperature is at least 120°F

and not more than 150°R Adjust water heater

if necessary.

[] Add two quarts of water to the bottom of the

dishwasher to lubricate the pump seal.

[] Turn on water supply.

[] Check for water leaks. Tighten connections

if necessary. See Step 14.

[] Remove the protective film, if present, from

the control panel, access panel and door panel.

Dishwasher Installation

STEP 19: DISHWASHER WET TEST

CHECKLIST

[] Turn on power supplg or if power cord is used,

plug it into the wall outlet

[] Latch dishwasher door

[] For electronic dishwashers, select the NORMAL

WASH cgcle and press the STARTpad one time

C_J_s Options c_,,_

U ii@

IS(.........................................

[] For dial models, press the NORMAL and HOT

START pads, if model has them, and then turn the

control dial just enough to start the dishwasher

Be careful not to turn the dial past the first water

fill Dial should point to "Hot Start Option" or "Hot

Prewash Option" depending on model

- Check the electrical connection to the water

valve The red electrical connector should be

plugged into the dishwasher water valve If it

is not plugged in, turn off electrical power to

the dishwasher Plug the red connector into the

dishwasher water valve and then restore power

RedConnector

Hot Start

Option Start

Cucles Options 4. "

StartDelau%q, ....

Cycle (MRS)

• Off o Light Wash

Pots Hear u Hi-Temp Heated Reset (Heated DruOn)

Po_ os os oru

Ri_seOnlL

(Heated Dru _ffl

Appearance varies by model. Not all models have push buttons.

[] Check to be sure that water enters the

dishwasher This could take up to/4 minutes

If water does not enter the dishwasher:

- Check to be sure that the water is turned on

- Lightly tap the flood float cover to dislodge

a stuck flood float

Cover

[] Check for leaks under the dishwasher Ifa leak is

found, turn off power, tighten connections and

restore power

[] Check for leaks around the door A leak around

the door could be caused bUthe dishwasher door

rubbing or hitting adjacent cabinets Reposition

the dishwasher if necessar U See Steps 11, 12

and 13.

[] Host dishwasher models will drain about

3 minutes after the first fill Check the drain line

for leaks when dishwasher drains If leaks are

found, turn off power, correct as necessar U

and then restore power

[] Open the dishwasher door and make sure most

of the water has drained If the water does not

drain, check to be sure disposer plug has been

removed and/or air gap is free of debris

[] Let the dishwasher run through another fill and

drain cycle Check again to be sure there are no

leaks

[]

At the end of the second drain, push the reset pad

on electronic models For dial models, unlatch the

door and rotate the dial to the "Off" position

Dishwasher Installation

STEP 20: REPLACE ACCESS PANEL AND

TOEKICK

In this step you will need the panels and the two

screws set aside in Step 4.

There are two tgpes of screws used. The 8-32 x 1/4"

screws are used at the top of the access panel and

should still be in place. The 10-16 x :3/8" screws are

used at the bottom of the access panel and secure

both the access panel and toekick.

STEP 21: LITERATURE

[] Leavethe Owners' Manual, Installation

Instructions, samples and/or coupons with

consumer.

IMPORTANT - screws are not

interchangeable. To prevent damage to your

dishwasher, use the proper screw in the proper

location. Do not mix screw tgpes or lengths.

• Place the toekick against the legs of the

dishwasher.

, Remove the two 8-32 x 1//4" machine-thread

screws.

• Align the access panel to the dishwasher.

• Select the two 8-52 x 1//4" machine-thread screws

just removed and insert them through the top

holes in the access panel and into the dishwasher

frame.

• Tighten these screws.

• Align the toekick and make sure the bottom edge

is against the floor.

• Insert and tighten the two 10-16 x 5/8" sheet metal

thread screws, making sure the bottom edge of

the toekick stags in contact with the floor.

Remove, Then Reinstall and Tighten

8-32 x !/4"

Machine-Thread Screws

..........

Instatl end Tighten .....

10-16 × 3/8"

Sheet tVletaI-ThreadScrews

Figure AA

Tip: Prevent tub damage and reduce sound from

under the dishwasher.

Use the machine-thread screws in the top holes and

the sheet metal-thread screws in the bottom holes.

Make sure the toekick is against the floor.

Appendix

CONVERTING DISHWASHER WITH FACTORY-

EQUIPPED POWER CORD TO A PERMANENT

CONNECTION

This procedure requires the conversion leads set

aside in Step 1.

. Make sure the power cord for the dishwasher is

unplugged from the wall outlet.

. Remove screw from junction box cover and

remove cover if present.

. Disconnect the three power cord conductors from

the dishwasher harness. See Figure BB.

. Remove and discard the power cord.

. Connect the conversion harness (included with

dishwasher) to the dishwasher harness by

connecting like-colored wires. See Figure CC.

. Return to Step 16 in these instructions to complete

the conversion.

Remove

Stroin Relief

Figure BB

Disconnect \

Power Cord --_

Figure CC

Conversion Harness

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

GEConsumer & Industrial

General Electric Company

Louisville, Kentucky 40225

GEAppliances.com

206C!559P!95 3!-30255

07-09 JR

Appareils m_nagers GE

Consumer and Industrial

Instructions d'installotion

L(]ve-v(]isselle enc(]str

Pour toute question, composez le 1.800.561.3344 ou visitez notre site Web"

www.electromenagersge.ca

AVANT DE COMMENCER

Veuillez lire attentivement toutes les

directives qui suivent.

IMPORTANT-Observeztous les codes

et ordonnances en vigueur.

• Note 6 I'installateur - Veuillez laisser les pr_sentes

directives au consommateur pour I'inspecteur local.

• Note au consommateur - Veuillez conserver les

pr_sentes directives avec votre Manuel d'utilisation

pour consultation ult_rieure.

• Comp6tences requises - L'installation de ce

lave-vaisselle exige des comp_tences de base

en m_canique, en _lectricit_ et en plombede.

L'installateur est responsable de la qualit6

de I'instailation. Toute d6faillance du produit

attribuable 6 une installation inad6quate n'est

pas couverte par la garantie de GE. Reportez-

vous 6 la garantie du produit.

• Dur6e de I'installation - Entre 1 et 3 heures.

L'installation d'un nouveau lave-vaisselle exige

plus de temps que le remplacement d'un ancien

module.

IMPORTANT- Le luve-vuisselle DOIT atre

install6 de mani_re 8 ce qu'il puisse 6tre sorti

de son emplacement si des r6purutions sont

n_cessuires.

Si le lave-vaisselle que vous avez request

endommag6, communiquez imm6diatement avec

votre d6taillant ou I'entrepreneur en construction.

Accessoires facultatifs - Reportez-vous au Manuel

d'utilisation pour connaTtre les ensembles pour

panneau d_coratif personnalis_ offerts.

POUR VOTRE SECURITE

Veuillez lire et observer toutes les mises en gurde

{ATTENTION et AVERTISSEMENT} donn6es duns les

pr6sentes directives. Pour effectuer I'instullution

d6crite duns les pr6sentes directives, il fuut porter

des gunts et des lunettes de s6curit6.

VEUILLEZ LIRE ATTENTIVEMENT ET

CONSERVER CES DIRECTIVES.

............ J

206C1559P195 31-30255 07-09 JR

PII_CES FOURNIES •

[] Deuxvis 6 bois Phillips n° 8-18 x 15,8 mm

(5/8 pal

[] Couvercle de la boTte dejonction et vis 6 t_te

hexagonale n° 10

[] Bogau de vidange (198 cm [78 pal de long)

et collier

[] Protege-cordon d'alimentation (modUles dot6s

d'un cordon d'alimentation seulement)

[] Fils pour la conversion (modUles dot6s d'un

cordon d'alimentation seulement)

[] Documentation, 6chantillons et(ou) bans

MATI]RIEL NI]CESSAIRE •

[] Cordon d'alimentation WX09X70910,

si n6cessaire pour votre installation

[] Connecteurs vissables homologu_s UL (:3)

[] Ruban pour joints filet6s

[] Coude de 90°, bague et 6crou 6 compression

(filetage externe NPT de 9,5 mm [3/8 pal

6 une extr6mit6 et I'autre extr6mit6 conque

pour le raccordement 6 la conduite

d'alimentation en eau)

[] Ensemble de supports de montage lat@aux

GPF65 si le comptoir est en granite

POUR UNE NOUVELLE INSTALLATION :

[] COble 61ectrique

[] Conduite d'alimentation en eau-tugau

en cuivre d'au mains 9,5 mm (:3/8 po)

[] Bague anti-traction pour le raccordement

61ectrique

[] Robinet d'arr_t (recommand6)

[] Coupure anti-refoulement pour le bogau

de vidange, si n6cessaire

[] Raccord en T pour la plomberie de la r6sidence,

s'il g a lieu

[] Bogau de vidange GPF10S (:3m / 10 pi de long),

si n6cessaire

[] Colliers 6 vis sans fin

OUTILS NI_CESSAIRES •

[] Lunettes de s6curit6

[] Tourne-6crous de 6,3 mm (1/4 po) et de 7,9 mm

(5/16 po)

[] Lampe de poche

[] Gants

[] CI6 6 molette (15,2 cm [6 po])

[] Tournevis Phillips

[] Ruban 6 mesurer

[] Niveau

[] Equerre de charpentier

[] Seau pour recueillir I'eau Iors du rin_age

de la conduite d'eau

[] Coupe-tubes

[] CI6 6 douille de 2:3,8 mm (15/16 po)

POUR UNE NOUVELLE INSTALLATION"

[] Jeu de scies-clochet

[] Perceuse et forets appropri6s

Ensemble de Vis

Vis 6 bois Phillips _ Vis 6 t_te hexagonale n° 10

n° 8 de 15,8 mm _ de 12,7 mm {I12 po) de long

15/8 po) de long pour bo?te dejonction

Bogau de vidange

de 198 cm {78 po)

Collier

Protege-cordon

d'alimentation

{modUles dot_s d'un

cordon d'alimentation

seulement)

Fils pour la

conversion lmod_les

dot_s d'un cordon

d'alimentation

seulement}

Couvercle

de la baste

de jonction

COble _lectrique ou

cordon d'alimentation

WRO9×70910

3 connecteurs vissables

Conduite d'eau chaude-

tugau en cuivre d'au

moins 9,5 mm 13/8 po)

Bague

anti-traction

Ensemble

de supports

de montage

lat_rau× GPF65

Ruban pour

joints filet_s

Robinet

d'arr_t

Coupure

anti-refoulement

Bogau de vidange

facultatif GPFIOS

de 3 m 110 pi)

Coude de 90°, bague

et _crou 6 compression

Colliers 6 vis sans fin

Raccord en T

Lunettes de s_curit_

Gants Cl_ 6 molette

Ruban 6 mesurer

_ Lampe de poche

Tourne-_crous

de 6,3 mm 11/4 po)

et de 7,9 mm {5/16 po)

Seau

Coupe-tubes

Niveau

Tournevis

Perceuse

et forets

Cl_ 6douille de 23,8mm

115116po)

Jeu de

scies-cloche

Equerre de

charpentier

Preparation pour I'installation - Ouverture dans les armoires

PRI_PARATION DE L'OUVERTURE DANS

LES ARMOIRES

Pour r_duire les nsques de choc

_lectrique, d'incendie ou de blessures,

Hnstalleteur doit s'essurer que le lave-

vaisselle est compl_tement encastr_

au moment de I'installation.

• L'ouverture duns les armoires doit mesurer au

moins 61,0 cm (2/4 po) de largeur et de profondeur,

et 87,6 cm _+6,3 mm (3/4 1/2 po _+1//4 po) de

hauteur 5 partir du plancherjusqu'au-dessous

du comptoir.

, Lemur du fond dolt _tre exempt de tuyaux

ou de ills.

, Les armoires udjocentes doivent _tre 5 1'6querre

et d'oplomb pour une installation appropri6e.

Reportez-vous 5 lu Figure A.

, Duns le cas d'une installation dons un coin,

pr6vogez unjeu d'au moins 5,1cm (2 po)entre

le luve-vaisselle et lemur adjacent.

, Pr6vogez ou moins 69 cm (27 po) a I'ovant

du lave-vaisselle pour ouvrir la porte

compl_tement. Reportez-vous 5 Io Figure B.

• Le Iove-vuisselle doit _tre installs ou maximum

5 3 m_tres (10 pieds) de 1'6vier pour assurer une

vidange ad6quate.

, Le dessus, les c6t6s et I'urri_re du Iove-voisselle

doivent _tre compl_tement dissimul6s 5 I'int6rieur

de I'ouverture.

, Le Iove-vaisselle ne dolt soutenir aucune portie

de la structure des armoires.

J Comptoir

°v°-v°iss°lli1 169cm/27no/

minimum

5,1 cm (2 po) minimum

D_gegements :

Dans le cas d'une installation

dans un coin, veuillez pr6voir

un d6gagement d'au moins

5,1 cm {2 po) entre le lave-

vaisselle et les armoires,

le mur ou un 61ectrom6nager

adjacent.

Veuillez pr6voir un

d6gagement d'au moins

69 cm (27 po) _ I'avant

du lave-vaisselle.

Figure B

87,6 cm +_6,3 mm

(34 1/2 po _+1/4 po) min.

du dessous

du comptoir !10,1cm

au plancher (4po)

Armoires

1'6querre

_lomb

Le plancher DOlT

6tre au m6me niveau La partie ombr_e est r_serv_e

que le plancher 8 Io plomberie et 8 I'_lectricit_

de la piece

Figure A

• Assurez-vous que le ploncher est de niveou

a I'int6rieur de I'ouverture et ou m_me niveou

que le plancher fini de la cuisine urin de fuciliter le

retrait du lave-vaisselle sijamais il faut ler6parer

dans le futur.

Preparation pour l'installation - Vidange

PREPARATION DE LA PLOMBERIE POUR

LAVIDANGE

Exigences relatives au syst_me de vidange

• Veuillez observer les ordonnances etles codes

Iocaux en vigueur.

• Le bogau de vidange doit avoir une Iongueur

maximale de 3 m_tres (10 pieds).

• IIfaut pr_voir une boucle de vidange _lev_e

ou I'installation d'une coupure anti-refoulement.

Voir ci-dessous.

H_thode de vidange

Le tupe d'installation de vidange d@pend des

conditions suivantes :

• Les ordonnances ou codes Iocaux en vigueur

exigent-ils une coupure anti-refoulement?

Le raccord en T se trouve-t-il 0 mains de/46 cm

(28 po)du plancher?

Sivous r@pondez OUI 5 I'une ou I'autre de ces

questions, vous devez installer une coupure anti-

refoulement (m_thode n° 1). Si vous r@pondez

NON aux deux questions, vous pouvez installer

une coupure anti-refoulement ou am@nager

une boucle de vidange @lev@e(m_thode n° 2).

Considerations sp_ciales dans le cas d'un

lave-vaisselle install(_ sur une plateforme

Si le lave-vaisselle est install_ sur une plateforme,

il faut am_nager une boucle de vidange 5 une

hauteur d'au moins 82 cm (:32po) au-dessus de

la plateforme, en plus d'installer la coupure anti-

refoulement indiqu_e ci-dessus, afin d'assurer une

vidange adequate.

ATTENTION

II FAUT installer une coupure anti-refoulementsi le bogau

de vidange est reli_ a un raccord en T ou 8 un broyeur

(_d_chets situ_ _ mains de 46 cm (18 po) du plancher.

Si le boyau de vidange avec la coupure anti-refoulement

ne setrouve pas (_une hauteur minimale de 82 cm (32 po)

au-dessus du plancher, la boucle de vidange _lev_e

ne pourra pas assurer une vidange appropri_e du

lave-vaisselle, ce qui pourrait causer des dommages

(_l'appareil.

HI_THODE N° 1 - Coupure anti-refoulement avec

raccord en T ou broyeur 6 d_chets

Installation avec raccord en T Installation avec broyeur d d@chets

HI_THODE N° 2 - Boucle de vidange (_lev(_eavec

raccord en T ou brogeur 6 d_chets

Pr_vouez une faqon de fixer le bouau de vidange

au-dessous du comptoir. La fixation du bouau de

vidange sera effectu@e 0 une @tape ult@rieure.

Installation avec raccord en T

Figure D _F

Installation avec broyeur _ d_chets

Installez le raccord en T ou le broueur 5 d@chets

et la coupure anti-refoulement en conformit@ avec

les directives du fabricant.

Preparation des armoires

Percez un trou de 3,8 cm (1 1/2 po)de diam@tre

dans la paroi de I'armoire qui se trouve dans

la partie ombr@e de la Figure A pour le bouau

de vidange. Assurez-vous que I'orifice ne pr@sente

pas d'ar@tes vives. Le bouau de vidange sera ins@r@

dans ce trou et raccord@ au renvoi au cours d'une

@tape ult@rieure.

IMPORTANT- Lorsque vous

branchez le bogau de vidange

6 un brogeur 6 d(_chets, assurez-

vous d'enlever le bouchon

de vidange. Le lave-vaisselle

ne pourra pas se vider si vous

laissez le bouchon en place.

4 nlevezle

bouchon

de vidange

La page est en cours de chargement...

Hotpoint HDA3600R00CC Guide d'installation

Marque: Hotpoint

Modèle: HDA3600R00CC

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Hotpoint HDA3600R00CC Installation guide

Hotpoint HDA3600R00CC Guide d'installation

Hotpoint HDA3600R00CC Guide d'installation

dans d''autres langues

Documents connexes

Autres documents