Danby DAC150BBUWDB Le manuel du propriétaire

Marque: Danby

Modèle: DAC150BBUWDB

Catégorie: Climatiseurs split-system

Taper: Le manuel du propriétaire

Ce manuel convient également à

DAC150BBCWDB

OWNER’S USE AND CARE GUIDE

GUIDE D’UTILISATION ET D'ENTRETIEN

02'(/02'Ê/(

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

AIR CONDITIONER

CLIMATISEUR

DAC150BBCWDB / DAC150BBUWDB

2017.01.12

This product is factory equipped with a power supply cord that has a three-pronged grounded plug. It must

be plugged into a mating grounding type receptacle in accordance with the National Electrical Code and

applicable local codes and ordinances. If the circuit does not have a grounding type receptacle, it is the

responsibility and obligation of the customer to exchange the existing receptacle in accordance with the

National Electrical Code and applicable local codes and ordinances. The third ground prong should not,

under any circumstances, be cut or removed. Never use the cord, the plug or the appliance when they show

any sign of damage. Do not use your appliance with an extension cord unless it has been checked and test-

ed by a qualiﬁ ed electrician or electrical supplier.

IMPORTANT - GROUNDING METHOD

Ce produit arrive d’origine avec un cordon d’alimentation équipé d’une prise à trois ﬁ ches. Il doit être

branché dans une prise avec une ﬁ che de mise à la terre en conformité avec le Code national de l’électricité

et les codes et règles locaux applicables. Si la prise murale n’a pas de mise à la terre, il est de la

responsabilité et l’obligation du client de changer la prise existante pour la rendre conforme au Code

national de l’électricité et aux codes et règles locaux applicables. La ﬁ che de mise à la terre ne doit pas, en

aucune circonstance, être coupée ou retirée. Si vous apercevez des signes de dommage, n’utilisez jamais le

cordon d’alimentation, la prise ou l’appareil. N’utilisez jamais l’appareil avec une rallonge sauf si elle a été

vériﬁ ée et testée par un électricien qualiﬁ é ou un fournisseur de matériel électrique.

IMPORTANT - MÉTHODE POUR LA MISE À LA TERRE

AIR CONDITIONER

Owner’s Use and Care Guide ................................ 1-20

• Welcome

• Important Safety Information

• Features

• Installation Instructions

• Operation Instructions

• Care and Maintenance

• Troubleshooting

• Warranty

CLIMATISEUR

Guide d’utilisation et d’entretien..............................21-41

• Bienvenue

• Consignes de sécurité importantes

• Caractéristiques

• Consignes d’installation

• Consignes d’utilisation

• Soins et entretien

• Dépannage

• Garantie

CONTENTS

Model • Modèle

CAUTION:

Read and follow all safety rules and operating

instructions before ﬁ rst use of this product.

AVERTISSEMENT :

Veuillez lire attentivement les consignes de

sécurité et les instructions d’utilisation avant

l’utilisation initiale de ce produit.

TABLE DES MATIÈRES

DAC150BBCWDB / DAC150BBUWDB

WELCOME

Welcome to the Danby family. We are proud of our quality products, and we believe in dependable service, like you will

ﬁ nd in this Owner’s Use and Care Guide, and like you will receive from our friendly customer service department. Best of

all, you will experience these values each and every time you use your Danby appliance. That is important, because your

new appliance will be a part of your family for a long time.

For easy reference, we suggest you attach a copy of your sales slip/receipt to this page, along with the following

information, located on the manufacturer’s nameplate on the right side of the unit above the powercord.

Note the information below; you will need this information to obtain service under warranty.

To receive service, you must provide the original receipt.

NOTE: THIS UNIT IS NOT DESIGNED FOR “THROUGH-THE-WALL” INSTALLATION.

Model No:

Serial No:

Date Purchased:

NEED HELP?

Before you call for service, here are a few things you can do to

help us serve you better:

Read this Owner’s Use and Care Guide:

It contains instructions to help you use and maintain your

appliance properly.

If you received a damaged appliance:

Immediately contact the retailer (or builder) that sold you the

appliance.

Save time and money:

Check the Troubleshooting section at the end of the guide

before calling. This section helps you solve common problems

that may occur.

If you do need service, you can relax, knowing help is only a

phone call away.

WARNING

Improper connection of the grounding plug can result in risk of

ﬁ re, electric shock and/or injury to persons associated with the

appliance. Check with a qualiﬁ ed service representative if in doubt

that the appliance is properly grounded.

1-800-26-

(1-800-263-2629)

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

FOR YOUR SAFETY: Read these instructions carefully before operating the unit.

ELECTRICAL SPECIFICATIONS

1. All wiring must comply with local and national electrical codes and must be installed by a qualiﬁ ed electrician. If you

have any questions regarding the following instructions, contact a qualiﬁ ed electrician.

2. Check available power supply and resolve any wiring problems BEFORE installing and operating this unit.

3. This 115V or 230/208V air conditioner uses 11.5 or less nameplate amps and may be used in any properly wired,

general purpose household receptacle. See Table 1 for speciﬁ cations for individual branch circuit.

4. For your safety and protection, this unit is grounded through the powercord plug when plugged into a matching wall

outlet. If you are not sure whether your wall outlet is properly grounded, please consult a qualiﬁ ed electrician.

5. The wall outlet must match the 3-prong plug on the service cord supplied with the unit. DO NOT use plug adapters.

See Table 2 for receptacle and fuse information.

6. The rating plate on the unit contains electrical and other technical data. The rating plate is located on the right side of

the unit, above the powercord.

TABLE 1

Suggested Individual Branch Circuit

Nameplate Amps *AWG Wire Size

11.5 14

AWG- American Wire Guage

*Based on copper wire at 105°C (221°F) temperature

rating.

TABLE 2

Recept and Fuse Types

Model DAC150BBCWDB / DAC150BBUWDB

Rated Volts 125 240

250

Amps 15 15

Wall Outlet

Fuse Size 15 15

Time Delay Fuse Plug Type

(or Circuit Breaker)

Do not, under any

circumstances, cut,

remove, or bypass

the grounding prong.

Your appliance is designed to be highly efﬁ cient in energy savings. Follow these recommendations for greater efﬁ -

ciency.

1. Select a thermostat setting that suits your comfort needs and leave at that chosen setting.

2. The air ﬁ lter is very efﬁ cient in removing airborne particles. Keep the air ﬁ lter clean at all times (usually cleaned every

2 weeks depending on indoor air quality).

3. Use drapes, curtains or shades to keep direct sunlight from penetrating and heating the room, but do not allow drapes

or curtains to obstruct the air ﬂ ow around the unit.

4. Start your air conditioner before the outdoor air becomes hot, to avoid an initial period of discomfort while the unit is

cooling the room.

5. When outdoor temperatures are cool enough, use the FAN MODE only, on HIGH, MEDIUM, or LOW setting. This

circulates indoor air, providing some cooling comfort, and utilizes less electricity than when operating on a cooling

setting.

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

FOR YOUR SAFETY: Read these instructions carefully before operating the unit.

ENERGY SAVING TIPS

The power cord supplied with this air conditioner contains a device that senses damage to the power cord. To test if your

power cord is working properly, you must do the following:

1. Connect the power supply cord to an electrical outlet.

2. The power supply cord has two buttons located on the head of the plug. One button is marked “TEST”, and the other

is marked “RESET”. Press the “TEST” button; you will hear a click as the “RESET” button pops out.

3. Press the “RESET” button; you will hear a click as the button engages.

4. The power supply cord is now energized and supplying electricity to the air conditioner (on some products this is also

indicated by a light on the plug head).

NOTE: The power cord supplied with this air conditioner contains a current leakage detection device designed to reduce

the risk of ﬁ re. In the event the power supply cord is damaged, it cannot be repaired and must be replaced with a new

cord from the product manufacturer.

• Under no circumstances should this device be used to turn the unit on or off.

• The “RESET” button must always be pushed in (engaged) for correct operation.

• The power supply cord must be replaced if it fails to reset when the “TEST” button is pushed in.

NOTE: Some plugs have buttons on the top.

POWER SUPPLY CORD

Plug in and press

RESET

TEST

RESET

FEATURES

Control Panel

Interior Air

Inlet

Cabinet

UNIT CONTROL PANEL

1. ON/OFF Button: Press to turn the unit on/off. NOTE: The unit will automatically launch the Energy Saver function

when it is in Cool, Dry and Auto modes.

2. Temperature UP/DOWN Buttons: To change the temperature setting, press or hold either the UP ( ) or DOWN

( ) button, until the desired temperature is seen on the display. This temperature will be automatically maintained

anywhere between 17°C (62°F) and 30°C (86°F). In Cooling mode, the display reads the set temperature, while in

Fan mode, the current room temperature is displayed.

3. Fan Speed Button: Select from four different fan settings: Auto, Low, Med or High. Each time the button is pressed,

the fan speed is shifted.

4. Mode Button: Allows you to scroll through and select the desired operating mode: Auto, Cool, Dry and Fan. The se-

lected mode will be denoted by the adjacent indicator light.

Operation in Auto Mode:

• Auto is a pre-set factory program that automatically deﬁ nes the mode and fan speed, based on the set temperature

you have chosen. An example of Auto operation is as follows:

• If you would like to cool down your room, your desired / set temperature will be below the room temperature, and your

air conditioner will go into cooling mode. Once the room has reached your desired temperature, the air conditioner will

switch to Fan mode, and circulate the cooled air around the room. When the temperature in the room goes up, the

unit will switch back to cooling mode, and the Auto cycle will start again.

Operation in Dry Mode:

• Please note that in this mode you cannot set the desired humidity level, it is automatically pre-set. The fan speed in

this setting is defaulted to “low”. Since the compressor is operating in order to remove moisture from the air, you will

experience a degree of cooling as a by-product.

Operation in Fan Only Mode:

• Use this function, when cooling is not desired, such as for room air circulation, or to exhaust stale air. Remember

to open the vent during this function, but keep it closed during cooling, for maximum cooling efﬁ ciency. In this mode

you can choose any fan speed you prefer. In Fan mode, the temperature cannot be set, and the display will read the

current room temperature.

5. Energy Saver: This is the default setting on this model. The unit will automatically cycle the fan on and off while

the compressor is not in use. The fan will continue to run for 3 minutes after the compressor shuts off. The fan then

cycles on for 2 minutes at 10 minute intervals, until the room temperature is above the set temperature. At this point,

the compressor turns back on and cooling re-starts. When the unit is in Energy Saver mode, the indicator light above

the Energy Saver button will be illuminated. You can take the unit out of Energy Saver mode by pressing the Energy

Saver button - the indicator light about the button will turn off. If you choose the non-Energy Saver option, the fan will

run continuously when the compressor is not in use.

UNIT CONTROL PANEL

6. Sleep Button: Press the Sleep button to initiate the Sleep mode. In this mode, the selected temperature will

increase (when in cooling mode) by 1°C (2°F) one half-hour after Sleep mode has been selected. The temperature

will then increase by another 1°C (2°F) after an additional half-hour. This new temperature will be maintained for 6

hours before returning to the originally selected temperature. This ends the Sleep mode and the unit will continue to

operate as originally programmed. The Sleep mode program can be cancelled at any time during operation by

pressing the Sleep button again.

7. Timer (Auto Start / Stop Feature) Button: Pressing the Timer button will illuminate the indicator beside the word

“On”. This indicates that the Auto Start program has been initiated. Press or hold the Up ( ) or Down ( ) buttons

to change the Auto time by 0.5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The

control will count down the time remaining until the start of the program. The selected time will register in 5 seconds

and the system will automatically revert back to displaying the previous temperature setting. Turning the unit ON or

OFF at any time will cancel the Auto Start/Stop function.

8. Check Filter Button: This feature is a reminder to clean the air ﬁ lter for more efﬁ cient operation. The LED (light)

illuminates after 250 hours of operation. To reset after cleaning the ﬁ lter, press the check ﬁ lter button and the light

will go off.

ADDITIONAL FEATURES:

• The Cool circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This prevents

overheating of the compressor and possible circuit breaker tripping. The fan will continue to run during this time.

• The control will maintain any set temperature within 2°, between 15°C-32°C (60°F - 90°F).

• The control is capable of displaying temperature in Celsius (°C) or Fahrenheit (°F). To convert from one to the other,

press and hold the UP and DOWN Temp./Timer buttons at the same time for 3 seconds.

FEATURES

ADJUSTING AIR FLOW

The 4-way air directional louvers allow you to direct the air ﬂ ow up or down and left or right throughout the room as needed.

RECOMMENDATION: When cooling, adjust blades to face upward. If you orient the air ﬂ ow blades downward and the unit

operates in cool mode for long periods of time, dew may form and drip from the surface of the blades.

Up or Down

Left or Right

OPERATING INSTRUCTIONS

USING THE REMOTE CONTROL

Location of the remote controller

• Use the remote controller within a distance of 8 meters from the appliance, point-

ing it towards the receiver. Reception is conﬁ rmed by a beep.

• The air conditioner will not operate if curtains, doors or other materials block

the signals from the remote controller to the indoor unit.

• Prevent any liquid from falling into the remote controller. Do not expose the

remote controller to direct sunlight or heat.

• If the infrared signal receiver on the indoor unit is exposed to direct sunlight,

the air conditioner may not function properly. Use curtains to prevent the

sunlight from falling on the receiver.

• If other electrical appliances react to the remote controller, either move these

appliances or call the service depot.

CAUTION

REMOTE CONTROLLER SPECIFICATIONS

Model R15B

Rated Voltage 3.0V

Battery Type Button cell: CR2025

Battery Quantity 1pcs

Lowest Voltage of CPU Emitting Signal 2.0V

Signal Receiving Range 8m

Environment -8°C to 60°C (18°F to 140°F)

Model / Modèle :

R15B

ON/OFF BUTTON

Operation starts when this button

is pressed and stops when the

button is pressed again. NOTE:

The unit will automatically launch

the Energy Saver function when

it is in Cool, Dry, and Auto modes

(Only Auto-Cool and Auto-Fan

modes.)

TEMP UP BUTTON

Push this button to increase the

temperature setting in 1°C (1°F)

increments to 30°C (86°F) .

FAN BUTTON

Used to select the fan speed in

four steps:

LOW MED HIGH AUTO

ENERGY SAVER BUTTON

Press this button to activate the

energy saving mode. Press it

again to stop the function. This

function is available in COOL,

DRY, and AUTO modes (only

Auto-cool and Auto-fan modes).

MODE BUTTON

Each time you press this button,

a mode is selected in a sequence

that consists of AUTO, COOL,

DRY, FAN, and back to AUTO.

TEMP DOWN BUTTON

Push this button to decrease the

indoor temperature setting in 1°C

(1°F) increments to 17°C (62°F).

TIMER BUTTON

Push this button to activate the

“Auto Start” or “Auto Stop” pro-

gram from 0-24 hours (0.5/1 hour

increments).

SLEEP BUTTON

Press this button to activate the

SLEEP mode. This function is

available in COOL, and AUTO

modes only, and maintains the

most comfortable temperature for

you.

OPERATING INSTRUCTIONS

USING THE REMOTE CONTROLLER BUTTONS

Model / Modèle :

R15B

AUTO OPERATION

Ensure the unit is plugged in and power is available.

1. Press the ON/OFF button to start the air conditioner.

2. Press the mode button and select AUTO.

3. Press the TEMP + / - button to set the desired temperature. The temperature can be set

within a range of 17°C (62°F) to 30°C (86°F) in 1°C (1°F) increments.

NOTE:

1. In the auto mode, the air conditioner can logically choose the mode of Cool, Fan, Dehu-

midifying by sensing the difference between the actual ambient room temperature and

the set temperature on the remote controller.

2. In Auto mode, you cannot change the fan speed. It has already been automatically

controlled.

3. If the Auto mode is not comfortable for you, the desired mode can be selected manually.

-----------------------------------------------------------------------------------------------------------------------

Model / Modèle :

R15B

COOLING / FAN OPERATION

Ensure the unit is plugged in and power is available.

1. Press the ON/OFF button to start the air conditioner.

2. Press the MODE button to select Cool mode.

3. Press the TEMP +/- button to set the desired temperature. The temperature can be set

within a range of 17°C (62°F) to 30°C (86°F) in 1°C (1°F) increments.

4. Press the FAN button to select the fan speed in four-steps, LOW, MED, HIGH or AUTO.

NOTE:

In the FAN mode, the setting temperature is not displayed in the remote controller and you

are not able to control the room temperature either. In this case, only step 1, 2 and 4 may be

performed.

-----------------------------------------------------------------------------------------------------------------------

Model / Modèle :

R15B

DEHUMIDIFYING OPERATION

Ensure the unit is plugged in and power is available.

1. Press the ON/OFF button to start the air conditioner.

2. Press the MODE button to select Dehumidifying mode.

NOTE:

In the Dehumidifying mode, you cannot change the fan speed. It has already been automat-

ically controlled.

-----------------------------------------------------------------------------------------------------------------------

OPERATING INSTRUCTIONS

USING THE REMOTE CONTROLLER BUTTONS

Model / Modèle :

R15B

SLEEP OPERATION

• In this mode, the selected temperature will increase (when in cooling mode) by 1°C (2°F)

one half-hour after sleep mode has been selected.

• The temperature will increase by another 1°C (2°F) after an additional half-hour.

• This new temperature will be maintained for 6 hours before returning to the originally

selected temperature. This ends the Sleep mode and the unit will continue to operate as

originally programmed.

• The Sleep mode program can be cancelled at any time during operation by pressing the

Sleep button again.

-----------------------------------------------------------------------------------------------------------------------

Model / Modèle :

R15B

TIMER OPERATION

Pressing the TIMER button can set the Auto-start and Auto-stop time of the unit.

NOTE:

• To set Auto-start time, the unit must be in the OFF position.

• To set Auto-stop time, the unit must be in the ON position.

To set the Auto-start time

1. Push the TIMER button when the unit is off; only the Auto-start feature can be set.

2. Keep pressing the TIMER button. Each time pressed, will increase the selected time

by 0.5 hour increments. When the selected time has added up to 10 hours, each time

pressed will increase the selected time by 1 hour increments, up to 24 hours.

3. The time can be set in the range of 0-24 hours.

4. After the desired time has been selected, wait for about 10 seconds, until the setting

temperature reappears in the display window of the air conditioner. This indicates that

the program has been set.

-----------------------------------------------------------------------------------------------------------------------

Model / Modèle :

R15B

TIMER OPERATION

To set the Auto-stop time

1. Push the TIMER button when the unit is operational; only the Auto-stop feature can be

set.

2. Keep pressing the TIMER button. Each time pressed will increase the selected time by 1

hour increments, up to 24 hours.

3. The time can be set in a range of 0-24 hours.

4. After the desired time has been selected, wait for about 10 seconds, until the setting

temperature reappears in the display window of the air conditioner. This indicates that

the program has been set.

NOTE:

To cancel the TIMER setting, push the TIMER button until “0 hours” is displayed on the LCD

window of the air conditioner.

-----------------------------------------------------------------------------------------------------------------------

OPERATING INSTRUCTIONS

USING THE REMOTE CONTROLLER BUTTONS

Model / Modèle :

R15B

ENERGY SAVER OPERATION

This function is available in Cool, Dry, and Auto modes (only Auto-Cool and Auto-Fan

modes). The fan will continue to run for 3 minutes after the compressor has shut off. The

fan then cycles on for 2 minutes at 10 minute intervals, until the room temperature is

above the set temperature. At this point, the compressor turns back on and cooling starts.

-----------------------------------------------------------------------------------------------------------------------

• Protect the remote control from high temperatures, and keep it away from radiation exposure.

• Keep the control panel receiver out of direct sunlight.

• If the remote control will not be used for extended periods of time (vacations etc.), the battery should be removed.

• This Class B digital apparatus complies with the Canadian ICES-003 standard.

• The remote operates within a range of 8 meters (26 ft.) from the receiver located inside the main unit. Any obstruction

between the receiver and remote may cause signal interference, limiting the ability to program the main unit.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residen-

tial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaran-

tee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help. Changes or modiﬁ cations not approved by the

party responsible for FCC compliance could void the user’s authority to operate the equipment.

This appliance complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

OPERATING INSTRUCTIONS

CHANGING THE BATTERY ON THE REMOTE

The remote controller is powered by one button cell housed in the

rear part and protected by a cover. Remove the button cell accord-

ing to the arrow marked at the back of the remote controller.

1. Slightly press “A” position according to the number 1 arrow

direction by your foreﬁ nger.

2. Press “B” position and pull it according to the number 2 arrow

direction by your thumb.

3. The above step 1 and 2 should be done simultaneously to

slide the button cell out.

INSTALLATION INSTRUCTIONS

TOOLS NEEDED FOR INSTALLATION:

• Screwdrivers: Phillips and ﬂ at head.

• Power Drill: 1/8in. (3.2mm) diameter drill bit

• Pencil

• Measuring Tape

• Scissors

• Carpenter’s Level

ELECTRIC SHOCK HAZARD

To avoid the possibility of personal injury, disconnect power to the unit before installing or servicing.

NOTE: Your Room Air Conditioner is designed for easy installation in a single or double-hung window.

This unit is NOT designed for vertical (slider type) windows and/or through-the-wall applications.

INSTALLATION INSTRUCTIONS

BEFORE INSTALLING

• Check window opening size against dimensions of your unit.

• Check condition of window; all wood parts of the window must be in good shape and able to ﬁ rmly hold the needed

screws. If not, make repairs before installing unit.

• Check for anything that could block airﬂ ow; check area outside window for things such as shrubs, trees, or awnings.

Inside, be sure furniture, drapes or blinds will not stop proper air ﬂ ow.

• Carefully unpack air conditioner. Remove all packing material, and check for all included installation hardware.

Model type: DAC150BBCWDB

DAC150BBUWDB

Unit height: 17.91

Unit width: 23.62

Min. window opening: 18 1/2”

Min. window width: 27 3/4”

Max. window width: 40 1/2”

7/16” locking screw

& flat washer for

window panels

1/2in.(13mm)

long Hex-head

screw

Safety Lock

1/2in.(12.7mm)

long screw and

locknut

3/4” long flat head

bolt and locknut

Sill Angle Bracket

5/16in. long Hex-head

locking screw for top

angle side retainer.

13/16in. (20mm)

screw

Frame lock

2 each

4 each

2 each

Fig. 1 INSTALLATION HARDWARE

Foam insert

Windowsash

seal foam

Weather-Stripping

Foam Insert

1. This room air conditioner is designed to ﬁ t easily into a single or double hung window. However, since window designs

vary, it may be necessary to make some modiﬁ cations for safe, proper installation.

2. Make sure window and frame are structurally sound and free from dry and rotted wood.

3. For maximum efﬁ ciency, install the air conditioner on a side of the house or building which favours more shade than

sunlight. If the unit is in direct sunlight, it is advisable to provide an awning over the unit.

4. Provide sufﬁ cient clearance around the cabinet to allow for ample air circulation through the unit (See Fig. 2). The

rear of the unit should be outdoors. It should not be in a garage, or inside a building. Keep unit as far away as possi-

ble from obstacles/obstructions and at least 30 in. (76 cm) above the ﬂ oor or ground. Curtains and other objects within

the room should be prevented from blocking the air ﬂ ow.

5. Be certain that the proper electrical outlet is within reach of the installation. Use only a single outlet circuit rated at 15

amps. All wiring should be in accordance with local and national electrical codes.

6. DO NOT install unit where leakage of combustible gas is suspected. Your air conditioner may fail to operate in air

containing oils (including machine oils), sulﬁ de gas, near hot springs, etc.

NOTE: Your unit is designed to evaporate condensation under normal conditions. However, under extreme humidity con-

ditions, excess condensation may cause basepan to overﬂ ow to the outside. The unit should be installed where conden-

sation run-off cannot drip on pedestrians or neighbouring properties.

NOTE: It is normal for your unit to drip a small amount of water, especially on excessively humid days.

INSTALLATION INSTRUCTIONS

LOCATION

Awning

Fence,

wall, or

other

obstacle

Ground

Side

Obstruction

20 in.

(50.8 cm)

Min

30 in. (76.2 cm)

Min

12 in. (30.5 cm) Min

20 in.

(50.8 cm)

Fig. 2

NOTE: Save the shipping carton and packing materials for future storage or transportation. From the carton, remove the

plastic bag containing the installation hardware kit necessary for the installation of your air conditioner. Please check the

contents of the hardware kit against the corresponding model check list, prior to installation.

NOTE: Your Room Air Condtioner is designed for easy installation in a single or double-hung window. This unit is NOT

designed for vertical (slider type) windows and/or through-the-wall applications.

CAUTION

Because the compressor is located on the controls

side of the unit (left side), this side will be heavier and

more awkward to manipulate. Inadequate support on the

control side of the unit can cause injury and damage to

the appliance and other property. Therefore, it is recom-

mended that you have someone assist you during the

installation of this unit.

INSTALLATION INSTRUCTIONS

WINDOW MOUNTING

Remove Chassis:

1. Pull down front panel and remove ﬁ lter (See Fig. A).

2. Lift front panel upwards and place to one side.

3. Locate the four (4) front screws and remove (Fig. B). These screws will be needed to re-install the front later.

4. Pry away the front panel from the cabinet sides as shown in Fig. C.

Fig. B

Fig. A

Fig. C

5. Gently lift front off unit and place to one side (See ﬁ g. D)

6. Remove shipping screw from top of unit and also on the side by the base if installed.

7. Hold the cabinet while pulling on the base handle, and carefully remove the chassis from the cabinet.

8. Add two foam inserts to holes in top of cabinet where shipping screws were removed from (See ﬁ g. E).

9. Your unit may come with internal packaging. This packaging must be removed prior to installing the air

conditioner back into the cabinet.

Fig. D

Fig. E

Foam inserts

INSTALLATION INSTRUCTIONS

Install Top Angle and Side Bracket:

1. Attach foam gasket to top angle above holes as shown in Fig. F.

2. Install top angle and side retainers to cabinet as shown in Fig. F.

5/16in. (8mm)

long hex-head

Fig. F

Assemble Window Filler Panels (see Fig. G):

1. Place cabinet on ﬂ oor, a bench, or table.

2. Slide the window ﬁ ller panel frame into the top (L

shaped) and bottom (U shaped) channels. The shut-

ters are identiﬁ ed (on the frame) as left and right.

3. Insert washer head locking screws (2) into holes in

top leg of ﬁ ller panel frame. Do not totally tighten. Al-

low left to slide freely. Screws will be tightened later.

Plastic

Frame

“U”Shaped Channel

Window Filler Panel

“L” Shaped Mounting

Bracket

Install Top Angle and Side Bracket:

1. Open window and mark center of window sill.

2. Place cabinet in window with lower “U” channel of

cabinet ﬁ rmly seated over window sill. Bring window

down temporarily behind top “L” bracket to hold

cabinet in place.

3. Shift cabinet left or right as needed to line up center

of cabinet on centre line marked on window sill.

4. Fasten cabinet to window sill with 2 screws (you

may want to pre-drill holes).

5. Add bottom rail seal over screws to window sill. See

Fig. H.

Fig. H

Bottom

Rail Seal

3/4in.(19mm) Long

Hex-head Screw

INSTALLATION INSTRUCTIONS

Install Support Bracket:

1. Hold each support bracket ﬂ ush against outside of sill, and tighten to bottom of cabinet as shown. in Fig. J

¹.

Mark brackets at top level of sill, and remove.

2. Assemble sill anchor bracket to outside support legs at the market position, as seen in Fig. J

Hand tighten,

but allow for any changes later. NOTE: Check that air conditioner is tilted downwards to the outside, about

3 ° to 4°, as shown in Fig. I. After installation, condensed water should not drain from the overﬂ ow drain hole

during normal use. If you notice water leaking out, check the angle of tilt, and make any necessary adjust-

ments. However, on a very humid day, water leakage can occur- this is normal. Measure the tilt angle from

the cabinet’s edge . The distance H should be approximately 1 1/4” to 1 5/8”.

3. Install support brackets (with sill anchor brackets attached) to correct hole in bottom of cabinet as shown in

Fig. K.

4. Tighten all 6 bolts securely.

Mark

Fig. J1

Left

Locknut

Sill Anchor

Bracket

Flat Head

Bolt

2 Each Required For

Each Support Bracket

Right

1/2in.(12.7mm) Long

Left Screws And

Locknuts

Fig. J2

Fig. K

Window Sill

Window Sash

$ERXWóWRǫ

Sill Angle Bracket

Side Louvers

Fig. I

Measure

the tilt

angle from

the cabinet’s

edge.

Extend Window FIller Panels

1. Carefully raise the window to expose the ﬁ ller panel locking screws. Loosen the screws do the ﬁ ller panels slide

easily.

2. Extend panels to ﬁ ll the widow completely. Using two 7/16 in (12mm) locking screws and a ﬂ at washer to tighten

the locking screws on top (Fig. L1).

3. Close the window behind the top angle.

4. Attach the top angle to the window frame using a 3/32 drill bit to drill one hole through the hole in the middle of

the top angle into the window frame, and drive one ½ HEX-HEAD locking screw through the hole in the middle

of the top angle into the window frame, see Fig. L2.

5. Extend the window ﬁ ller panels out against the window frame.

6. Use a 1/8” drill bit to drill a starter hole through the hole in the top leg of each window ﬁ ller panel and into the

window sash (Fig. L3). Connect with one ½” long hex head screw.

7. Attach the frame lock to the window sill using one 13/16” (20mm) screw on each side as shown in Fig. L3.

Locking Screw

7/16"Locking

Screw

and Washer

Fig.L2

1/ 2 long

HEX-HEAD

SCREW

Fig.15B

1/2in. (13mm) long

Hex-head screw

13/16in. (20mm) Screw & Frame Lock (2)

Fig. L3

)

Fig.L1

Install Window Lock and Sash Seal

1. Trim sash seal to ﬁ t window width. Insert into space between upper and lower sashes (Fig. M).

2. Attach right angle safety lock as shown in Fig. M.

INSTALLATION INSTRUCTIONS

Install Chassis into Cabinet and Install:

1. Lift chassis and carefully slide into cabinet, leaving 6 inches protruding.

2. DO NOT push on controls or coils.

3. Be sure the chassis is ﬁ rmly seated towards rear of cabinet.

4. Installation of front is the reverse of removal, outlined in section 1 (“Remove Chassis”)

Safety Lock

1/2” screw

Window

Sash Seal

Fig.M

Installing the Energy Efﬁ cient Foam Insert

• After the unit is installed in the window, measure the width of the side curtain.

• If necessary, cut the foam insert down to the width of the side curtain.

• Slide the foam insert into the side curtain.

• Repeat for the other side. (See below)

NOTE: Apply the supplied weather-stripping where needed (cracks and spaces between the foam insert, window

kit and window frame).





12345678910 1

1121314151617

Step 1 Step 3Step 2

CLEANING THE CABINET

• Be sure to unplug the air conditioner to prevent shock or ﬁ re hazard. The cabinet and front may be dusted with an

oil-free cloth or washed with a soft cloth dampened in a solution of warm water and mild liquid dishwashing detergent.

Rinse thoroughly and wipe dry.

• Be sure to wring excess water from the cloth before wiping around the controls. Excess water in or around the con-

trols may cause damage to the air conditioner.

WINTER STORAGE

If you plan to store the air conditioner during the winter, remove it carefully from the window according to the installation

instructions. Cover it with plastic or return it to the original carton. Always store the unit in the upright position.

DISPOSAL

Check for local regulatory compliance regarding the approved and safe disposal of this appliance.

CARE AND MAINTENANCE

CLEANING THE AIR FILTER

CAUTION

Before cleaning or servicing this unit, disconnect from any electrical supply outlets to prevent

possible shock or ﬁ re hazard.

• DO NOT use gasoline, benzene, thinner, or any other chemicals to clean this unit, as these substances may cause

damage to the ﬁ nish and deformation of plastic parts.

• Never use harsh cleaners, wax or polish on the cabinet front.

The air ﬁ lter should be checked at least once a month to see if cleaning is

necessary. Trapped particles in the ﬁ lter can build up and cause accumulation

of frost on the cooling coils.

• Push the vent handle to the vent closed position.

• Open the front panel.

• Grasp the ﬁ lter, pull up and out.

• Wash the ﬁ lter using liquid dishwashing detergent and warm water. Rinse

ﬁ lter thoroughly.

• Gently shake excess water from the ﬁ lter. Be sure the ﬁ lter is thoroughly

dry before replacing.

• You may vacuum the ﬁ lter to clean.

Note: Never use hot water over 40°C (104°F) to clean the air ﬁ lter.

CAUTION

Never operate this unit without the air ﬁ lter in place, as this may

result in damage to the unit.

La page charge ...

Danby DAC150BBUWDB Le manuel du propriétaire

Marque: Danby

Modèle: DAC150BBUWDB

Catégorie: Climatiseurs split-system

Taper: Le manuel du propriétaire

Ce manuel convient également à

DAC150BBCWDB

Télécharger le PDF

rapport

dans d''autres langues

English: Danby DAC150BBUWDB Owner's manual

Danby DAC150BBUWDB Le manuel du propriétaire

Ce manuel convient également à

Danby DAC150BBUWDB Le manuel du propriétaire

dans d''autres langues

Documents connexes