YoLink YS7104-UC Outdoor Alarm Controller Mode d'emploi

Marque
YoLink
Modèle
YS7104-UC Outdoor Alarm Controller
Taper
Mode d'emploi
LED Behaviors
Get to Know Your Outdoor
Alarm Controller, Cont.
E
Blinking Red Once, Then Green
Once
Device Start-Up
Blinking Red And Green
Alternately
Restoring to Factory Defaults
Blinking Green Once
Siren (or Output) Activated
Blinking Green
Connecting to Cloud
Slow Blinking Green
Updating
Fast Blinking Green
Control-D2D Pairing in Progress
Blinking Red Once
Siren (or Output) Deactivated
Fast Blinking Red
Control-D2D Unpairing in
Progress
Fast Blinking Red Every 30
Seconds
Low Battery; Replace Batteries
Soon
Add Your Outdoor Alarm
Controller to the App
H
1. Tap Add Device (if shown) or tap the
scanner icon:
Scanner icon
2. Approve access to your phone’s
camera, if requested. A viewfinder will be
shown on the app.
Wall Anchors
Drill with Drill Bits Medium Phillips
Screwdriver
Mounting Holes (3)
Tilt Adjustment
Mounting Base
Required Items
The following items will be required:
The following items may be required:
D
Get to Know Your Siren
F
Get to Know Your Outdoor
Alarm Controller
E
Wall-Mounting Slot
Enclosure Clamp
Latches
Combination SET
Button & Status
LED
Cable Connector
Before You Begin
B
Installation & User
Guide
Product Support
Support produit
Soporte de producto
Your Outdoor Alarm Controller connects
to the internet via a YoLink hub (Speak-
erHub or the original YoLink Hub), and it
does not connect directly to your WiFi or
local network. In order for remote
access to the device from the app, and
for full functionality, a hub is required.
This guide assumes the YoLink app has
been installed on your smartphone, and
a YoLink hub is installed and online (or
your location, apartment, condo,
etcetera, is already served by a YoLink
wireless network).
The Outdoor Alarm Controller is capable
of supplying 12VDC power to devices for
limited periods of time. The device must
have a current draw, including momen-
tary inrush current, less than 400 mA.
You can also find all current guides and
additional resources, such as videos and
troubleshooting instructions, on the
Outdoor Alarm Controller and Siren
Product Support Page by scanning the
QR code below or by visiting:
https://shop.yosmart.com/pages/
outdoor-alarm-controller-product-
support
Please note: this is a quick start guide,
intended to get you started on the
installation of your Outdoor Alarm
Controller and Siren. Download the full
Installation & User Guide by scanning
this QR code:
In the Kit
C
Power Up
G
4 x AA Batteries
3. Hold the phone over the QR code so
that the code appears in the viewfinder.
If successful, the Add Device screen will
be displayed.
You can change the device name and
assign it to a room later. Tap Bind
device.
If successful, the message “You have
successfully added this product!” will be
displayed. Tap Done.
4. Confirm the Outdoor Alarm Controller
is noted as being online before proceed-
ing to the next section. If not,
double-check the steps in the Power Up
section.
1. Install batteries in the Outdoor Alarm
Controller. This is done by releasing the
two clamp latches on the side of the
controller, then opening the cover. Then,
install four new AA batteries.
2. Close the cover, snapping the clamp
latches tightly into locked position.
3. Press the SET button briefly, long
enough for the LED to illuminate, blinking
red then green.
Power Up, Cont.
G
The Outdoor Alarm Controller is
optimized for standard alkaline batteries.
Lithium batteries may be used, but the
battery level may not be correctly
indicated in the app. False low-battery
indications may occur.
Do NOT use rechargeable batteries!
Outdoor Alarm
Controller
Siren Horn
ES-626
Quick Start Guide
Quick Start Guide
YS7104-UC & Siren Horn ES-626
Outdoor Alarm
Controller
Revision Jan. 06, 2023
Welcome!
A
Thank you for purchasing YoLink
products! We appreciate you trusting
YoLink for your smart home & automa-
tion needs. Your 100% satisfaction is our
goal. If you experience any problems
with your installation, with our products
or if you have any questions that this
manual does not answer, please contact
us right away. See the Contact Us
section for more info.
Thank you!
Eric Vanzo
Customer Experience Manager
The following icons are used in this guide to
convey specific types of information:
Very important information
(can save you time!)
Good to know info but may not apply
to you
Pour des instructions en
français, scannez les codes
QR dans la section suivante.
Para obtener instrucciones en
español, escanee los códigos
QR en la siguiente sección.
Fr
Es
Final Connections &
Testing
JContact Us
K
We are here for you, if you ever need any
assistance installing, setting up or using
a YoLink app or product!
Need help? For fastest service, please
email us 24/7 at [email protected]
Or call us at 831-292-4831 (US phone
support hours: Monday - Friday, 9AM to
5PM Pacific)
You can also find additional support and
ways to contact us at:
www.yosmart.com/support-and-service
Or scan the QR code:
Finally, if you have any feedback or
suggestions for us, please email us at
[email protected]
Thank you for trusting YoLink!
Eric Vanzo
Customer Experience Manager
Support
Home Page
15375 Barranca Parkway
Ste. J-107 | Irvine, California 92618
© 2022 YOSMART, INC IRVINE,
CALIFORNIA
Preparing for Installation
Determine where you will install your
Outdoor Alarm Controller and Siren.
Typically, they will be mounted together,
no farther apart from each other than the
cables allow. (Extension cables are
available, allowing for locating the siren
remotely from the controller)
Determine how you will mount the
controller and siren, and have appropri-
ate mounting hardware (screws,
anchors, etc.) and a means of installing
them in the wall or mounting surface on
hand.
It is important to securely mount the
Outdoor Alarm Controller and the Siren
to the wall or mounting surface, to
ensure they do not later fall down.
Physical damage to the device is not
covered by the warranty.
Consider if the controller or siren will be
subjected to tampering or vandalism.
Mounting them higher on the wall may
deter tampering.
Also, consider minimum mounting
heights. As the siren is very loud, you
should avoid locating it near head
height or at locations where people may
be present when it activates. Hearing
can be damaged by high decibel sounds,
such as the siren produces.
While the controller and siren are
designed for outdoor use, as with any
electronic or similar device, protecting it
from direct intense sunlight and from
rain or snow with overhead cover, can
extend its life and protect it from issues
like fading colors or dry and brittle
cables or plastic. Just under the eaves of
a roof or under an overhanging structure
is an ideal location for this product.
Pro tip: like the professional installers
may do, you can consider installing your
siren in the attic, if applicable. A location
in the attic may allow for sound to be
carried both inside the home as well as
outside (depending on siren proximity to
eaves or gable vents and the construc-
tion characteristics of your home).
You may consider testing the siren at the
proposed location before permanently
installing it, checking that the sound
carries as far as desired.
Additional Alarm Controllers and Sirens
can be added to your system, and may
be required for larger homes or buildings,
and larger yards or locations with sound
obstructions and/or high ambient sound
levels.
Installation
I
Protect your ears and those of others
that may be close to the siren during
testing. Consider warning your neighbors
you will be testing your siren, to avoid a
surprise visit from the police department!
Refer to the full installation and user
guide to complete the setup of your
Outdoor Alarm Controller and Siren.
1. Connect the cable of the controller to
the cable of the siren. Ensure the arrow
of the cable connector aligns with the
arrow of the other cable connector. Twist
the collar of the connector tight.
2. Test the siren by pressing the SET
button on the controller. The siren
should activate. Press the SET button
again to silence the siren.
2. If you are using wall anchors, install
them per the manufacturer instructions
(this may require a drill and appropriate
drill bit).
3. Secure the siren base to the wall or
mounting surface, with three screws.
Check that it is securely-mounted, by
gently tugging on it.
4. You can adjust the desired up/down
tilt of the siren at this time or during
testing.
Install the Siren
1. Holding the siren at the desired
location, transfer the location of the
three mounting holes to the wall or
mounting surface, using a marker or
similar means.
Install the Outdoor Alarm Controller
1. At the desired location for the
controller, confirm the cables of the two
devices will reach each other. Holding
the controller at the desired location,
mark the location of the mounting holes
to the wall or mounting surface, using a
marker or similar means.
2. If you are using wall anchors, install it
per the manufacturer instructions.
3. Secure the Alarm Controller to the wall
or mounting surface with a screw, as
shown.
If you are using the Outdoor Alarm
Controller with a 12V DC device other
than the included siren, such as a strobe
or relay, please note the following:
The device must be 12V DC, not AC,
not less or more than 12 volts.
The device current draw and inrush
current must be under 400
milliamps.
Correct polarity must be observed.
Do not attempt to power the device
for extended periods, as this will
quickly drain the battery.
Consider using the controller to
power a low-current 12VDC relay or
mechanically-latching relay, with the
load being powered by a separate
power source.
If splicing the cable to another cable
or device, use care to not damage
the antenna wire, which is attached
to the controller cable!
  • Page 1 1
  • Page 2 2

YoLink YS7104-UC Outdoor Alarm Controller Mode d'emploi

Marque
YoLink
Modèle
YS7104-UC Outdoor Alarm Controller
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents