Murray MS2560 Manuel utilisateur

Marque: Murray

Modèle: MS2560

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

769-08353 / 00 08/12

Operator’s Manual

2-Cycle Trimmer

TABLE OF CONTENTS

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Oil and Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Starting and Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

All information, illustrations, and specifications in this manual are based

on the latest product information available at the time of printing. We

reserve the right to make changes at any time without notice.

DO NOT RETURN THIS UNIT TO THE RETAILER. PROOF OF

PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE.

For assistance regarding the assembly, controls, operation or

maintenance of the unit, please call the Customer Support Department

at 1-800-800-7310 in the United States or 1-800-668-1238 in Canada.

Additional information about the unit can be found on our website:

www.mtdproducts.com (U.S.) or www.mtdproducts.ca (Canada).

For service, please call the Customer Support Department to obtain

a list of authorized service dealers near you. Service on this unit,

both within and after the warranty period, should only be performed

by an authorized and approved service dealer. When servicing, use

only identical replacement parts.

SAVE THESE INSTRUCTIONS

SERVICE

SAFETY

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the states of

California, Maine, Oregon and Washington. All U.S. Forest Land

and the state of California (Public Resources Codes 4442 and

4443), Oregon and Washington require, by law that certain internal

combustion engines operated on forest brush and/or grass-covered

areas be equipped with a spark arrestor, maintained in effective

working order, or the engine be constructed, equipped and

maintained for the prevention of fire. Check with your state or local

authorities for regulations pertaining to these requirements. Failure

to follow these requirements could subject you to liability or a fine.

This unit is factory equipped with a spark arrestor. If it requires

replacement, ask your LOCAL SERVICE DEALER to install the

Accessory Part #753-06418 Muffler Assembly.

Read the operator’s manual and follow all warnings and safety

instructions. Failure to do so can result in serious injury to the

operator and/or bystanders.

SYMBOL MEANING

WARNING:

Signals a SERIOUS hazard.

Failure to obey a safety WARNING signal CAN result in

serious injury to yourself or to others.

CAUTION:

Signals a MODERATE hazard.

Failure to obey a safety CAUTION signal MAY result in

property damage or injury to yourself or to others.

The purpose of safety symbols is to attract your attention to

possible dangers. The safety symbols, and their explanations,

deserve your careful attention and understanding. The safety

warnings do not by themselves eliminate any danger. The

instructions or warnings they give are not substitutes for proper

accident prevention measures.

NOTE: Advises you of information or instructions vital to the

operation or maintenance of the equipment.

DANGER:

Signals an EXTREME hazard.

Failure to obey a safety DANGER signal WILL result in

serious injury or death to yourself or to others.

CALIFORNIA PROPOSITION 65

WARNING:

Engine exhaust, some of its constituents and

certain finished components contain or emit chemicals known

to the State of California to cause cancer and birth defects or

other reproductive harm. Wash hands after handling.

READ ALL INSTRUCTIONS BEFORE OPERATING

• Read the instructions carefully. Be familiar with the controls and

proper use of the unit.

• Do not operate this unit when tired, ill or under the influence of

alcohol, drugs or medication.

• Children must not operate the unit. Teens must be accompanied

and guided by an adult.

• All guards and safety attachments must be installed properly

before operating the unit.

• Inspect the unit before use. Replace damaged parts. Check for

fuel leaks. Make sure all fasteners are in place and secure.

Replace parts that are cracked, chipped, or damaged in any

way. Do not operate the unit with loose or damaged parts.

• Only use the trimming line described in the Specifications section

of this manual. Never use metal-reinforced line, wire, chain or

rope. These can break off and become dangerous projectiles.

• Be aware of risk of injury to the head, hands and feet.

• Carefully inspect the area before starting the unit. Remove

rocks, broken glass, nails, wire, string and other objects that

may be thrown or become entangled with the unit.

• Clear the area of children, bystanders and pets; keep them

outside a 50-foot (15 m) radius, at a minimum. Even then, they are

still at risk from thrown objects. Encourage bystanders to wear

eye protection. If you are approached, stop the unit immediately.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments or

repairs before using the unit.

WHILE OPERATING

• Wear safety glasses or goggles that meet current ANSI Z87.1

standards and are marked as such. Wear ear/hearing protection

when operating this unit. Wear a face mask or dust mask if the

operation is dusty.

• Wear heavy long pants, boots, gloves and a long sleeve shirt. Do

not wear loose clothing, jewelry, short pants, sandals or go

barefoot. Secure hair above shoulder level.

• The cutting head shield must always be in place while operating

the unit. Do not operate the unit without both trimming lines

extended and the proper line installed. Do not extend the

trimming line beyond the length of the shield.

• This unit has a clutch. The cutting head remains stationary when

the engine is idling. If it does not, take the unit to an authorized

service dealer for an adjustment.

• Adjust the handle to provide the best grip.

• Make sure the cutting head is not in contact with anything

before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Be in the starting position whenever

pulling the starter rope. The operator and unit must be in a stable

position while starting. Refer to Starting and Stopping.

• Use the right tool. Only use this tool for its intended purpose.

• Always hold the unit with both hands when operating. Keep a

firm grip on both handles or grips.

• Do not overreach. Always keep proper footing and balance. Take

extra care when working on steep slopes or inclines.

• Keep hands, face, and feet away from all moving parts. Do not

touch or try to stop moving parts.

• Do not touch the engine, gear housing or muffler. These parts get

extremely hot from operation, even after the unit is turned off.

• Do not operate the unit faster than the speed needed to do the job.

Do not run the unit at high speed when not in use.

• Do not force the unit. It will do a better, safer job when used at

the intended rate.

• Always stop the unit when operation is delayed or when walking

from one location to another.

• If you strike or become entangled with a foreign object, stop the

unit immediately and check for damage. Do not operate the unit

before repairing damage. Do not operate the unit with loose or

damaged parts.

• Turn the engine to off and disconnect the spark plug for

maintenance or repair.

• Use only original equipment manufacturer (OEM) replacement

parts and accessories for this unit. These are available from your

authorized service dealer. Use of any other parts or accessories

could lead to serious injury to the user, or damage to the unit,

and void the warranty.

• Keep the unit clean. Carefully remove vegetation and other

debris that could block moving parts.

• To reduce fire hazard, replace a faulty muffler and spark arrestor.

Keep the engine and muffler free from grass, leaves, excessive

grease or carbon build up.

• If the unit starts to vibrate abnormally, stop the unit immediately.

Inspect the unit for the cause of the vibration. Vibration is

generally an indicator of trouble.

SAFETY WARNINGS FOR GAS UNITS

• Store fuel only in containers specifically designed and approved

for the storage of such materials.

• Always stop the engine and allow it to cool before filling the

tank. Never remove the fuel tank cap or add fuel when the

engine is hot. Always loosen the fuel tank cap slowly to relieve

any pressure in the tank before fueling.

• Always mix and add fuel in a clean, well-ventilated outdoor area

where there are no sparks or flames. DO NOT smoke.

• Never operate the unit without the fuel cap securely in place.

• Avoid creating a source of ignition for spilled fuel. Wipe up any

spilled fuel from the unit immediately, before starting the unit.

Move the unit at least 30 ft. (9.1 m) from the fueling source and

site before starting the engine. DO NOT smoke.

• Never start or run the unit inside a closed room or building.

Breathing exhaust fumes can kill. Operate this unit only in a well

ventilated outdoor area.

• IMPORTANT SAFETY INSTRUCTIONS •

WARNING:

When using the unit, all safety rules must be

followed. Please read these instructions before operating

the unit in order to ensure the safety of the operator and any

bystanders. Please keep these instructions for later use.

WARNING:

Gasoline is highly flammable and its vapors

can explode if ignited. Take the following precautions:

• SAFETY & INTERNATIONAL SYMBOLS •

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's

manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning or caution. May be used in

conjunction with other symbols or pictographs.

• READ OPERATOR'S MANUAL

WARNING: Read the operator’s manual(s) and

follow all warnings and safety instructions. Failure to

do so can result in serious injury to the operator

and/or bystanders.

• WEAR EYE AND HEARING PROTECTION

WARNING: Thrown objects and loud noise can

cause severe eye injury and hearing loss. Wear eye

protection meeting current ANSI Z87.1 standards and

ear protection when operating this unit. Use a full face

shield when needed.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

• OIL

Refer to operator’s manual for the proper type of oil.

• DO NOT USE E85 FUEL IN THIS UNIT

WARNING: It has been proven that fuel containing

greater than 10% ethanol will likely damage this

engine and void the warranty.

• ON/OFF STOP CONTROL

ON / START / RUN

• ON/OFF STOP CONTROL

OFF or STOP

• PRIMER BULB

Push primer bulb, fully and slowly, 10 times.

• THROWN OBJECTS AND ROTATING CUTTER CAN

CAUSE SEVERE INJURY

WARNING: Small objects can be propelled at high

speed, causing injury. Keep away from the rotating rotor.

• KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders, especially children

and pets, at least 50 feet (15 m) from the operating area.

• HOT SURFACE

WARNING: Do not touch a hot muffler or cylinder.

You may get burned. These parts get extremely hot

from operation. When turned off they remain hot for a

short time.

• SHARP BLADE

WARNING: Sharp blade on trimmer attachment

shield. To prevent serious injury, do not touch the line

cutting blade.

OTHER SAFETY WARNINGS

• All service, other than the maintenance procedures described in

this manual, should be performed by a qualified service dealer.

• Before inspecting, servicing, cleaning, storing, transporting or

replacing any parts on the unit:

1. Stop the unit.

2. Make sure all moving parts have stopped.

3. Allow the unit to cool.

4. Disconnect the spark plug wire.

• Secure the unit while transporting.

• Never store the unit with fuel in the tank, inside a building where

fumes may reach an open flame (pilot lights, etc.) or sparks

(switches, electrical motors, etc.).

• Store the unit in a dry place, secured or at a height to prevent

unauthorized use or damage. Keep the unit out of the reach of

children.

• Never douse or squirt the unit with water or any other liquid.

Keep handles dry, clean and free from debris. Clean the unit

after each use. Refer to Cleaning and Storage.

• Keep these instructions. Refer to them often and use them to

instruct other users. If you loan this unit to others, also loan

them these instructions.

SAVE THESE INSTRUCTIONS

Cutting Head

Shield

Fuel Cap

Handle

Cutting Head

Shaft Grip

Shaft Housing

Starter

Rope Grip

Throttle

Control

Spark Plug

Muffler

On/Off Switch

Line Cutting Blade

Air Filter

Cover

Coupler

Primer Bulb

Choke Lever

KNOW YOUR UNIT

APPLICATIONS

As a trimmer:

• Cutting grass and light weeds.

• Edging

• Decorative trimming around trees, fences, etc.

Other optional accessories may be used with this unit.

SPECIFICATIONS*

* All specifications are based on the latest product information available at the time of printing. We reserve the right to make changes at any

time without notice.

Engine Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled, 2-Cycle

Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 cc (1.52 cu. in.)

Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.025 in. (0.635 mm)

Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Champion® RDJ7J or equivalent plug

Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel/Oil Mixture

Fuel/Oil Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40:1

Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 oz. (296 ml)

Approximate Unit Weight (No fuel, with cutting head, cutting head shield and handle) . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 - 11 lbs. (4.5 - 5 kg)

Trimmer Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fixed-line cutting head

Trimming Line. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.095 inches (2.41 mm) pre-cut line

Cutting Path Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 in. (35.56 cm)

ASSEMBLY TOOLS REQUIRED:

• #2 Phillips screwdriver

• 3/8” Socket

ASSEMBLY

INSTALLING AND ADJUSTING THE HANDLE

Installing the Handle

1. Push the handle down onto the shaft housing (Fig. 2). The bolt

hole in the handle should be to the right.

2. Insert the bolt into the bolt hole and push it through (Fig. 2).

Tighten the bolt with a 3/ 8” socket, but do not tighten the bolt

completely .

3. While holding the unit in the operating position (Fig. 10), move

the handle to the location that provides the best grip. Place it a

minimum of 6 inches (15.24 cm) from the end of the shaft grip

(Fig. 2).

4. Tighten the bolt with a 3/ 8” socket until the handle is secure.

Adjusting the Handle

If the handle requires adjustment:

1. Loosen the bolt with a 3/ 8” socket (Fig. 2).

2. While holding the unit in the operating position (Fig. 10), move

the handle to the location that provides the best grip. Place it a

minimum of 6 inches (15.24 cm) from the end of the shaft grip

(Fig. 2).

3. Tighten the bolt with a 3/ 8” socket until the handle is secure.

INSTALLING THE CUTTING HEAD SHIELD

Use the following instructions if the cutting head shield is not

installed. Use only the instructions that apply to the type of shaft

and shield equipped with this unit.

1. Place the cutting head shield onto the mount bracket. Align the

holes in the cutting head shield with the holes in the mount

bracket. (Fig. 1)

2. Screw the 2 screws through the mount bracket and into the

cutting head shield until finger tight.

3. Using a #2 Phillips screwdriver, tighten the screws until the

cutting head shield is firmly in place. Tighten the screws equally.

The gap between the mount bracket and the cutting head shield

should be the same on each side.

Fig. 1

Mount Bracket

Cutting Head

Shield

Screws (2)

WARNING:

To prevent serious personal injury, never

operate the unit without the cutting head shield in place.

Fig. 2

Bolt

Shaft Grip

Minimum 6 in.

(15.24 cm)

Handle

Shaft

Housing

Fig. 4

Fig. 5

Fig. 3

Release Button

Guide Recess

90˚ Edging Hole

(Trimmer Only)

Knob

Primary Hole

Lower Shaft

Housing

Upper Shaft

Housing

OPERATING THE COUPLER

The coupler enables the use of various optional attachments.

NOTE: To make installing or removing the attachment easier, place

the unit on the ground or on a work bench.

Installing the Attachment

NOTE: Remove the protective cap and gray spacer from the upper

and lower shafts prior to assembling the attachment.

1. Turn the knob counterclockwise to loosen (Fig. 3).

2. While firmly holding the attachment, push it straight into the

coupler until the release button snaps firmly into the primary

hole (Fig. 5).

NOTE: Aligning the release button with the guide recess will help

installation (Fig. 4).

3. Turn the knob clockwise to tighten (Fig. 3).

For decorative edging with a string trimmer attachment, lock the

release button into the 90° edging hole (Fig. 3).

Removing the Attachment

1. Turn the knob counterclockwise to loosen (Fig. 3).

2. Press and hold the release button (Fig. 4).

3. While firmly holding the upper shaft housing, pull the attachment

straight out of the coupler (Fig. 5).

WARNING:

Before using any attachment, read and

understand the manual that came with the attachment.

Follow all safety information contained within.

CAUTION:

Before operating the unit, make sure the

release button is fully snapped into the primary hole (Fig. 5)

and the knob (Fig. 3) is securely tightened.

WARNING:

To avoid serious personal injury and

damage to the unit, shut the unit off before removing or

installing an attachment.

CAUTION:

The release button should be snapped into

the primary hole only. Using the wrong hole could lead to

personal injury or damage to the unit.

Coupler

OIL AND FUEL

FUELING THE UNIT

1. Position the unit with the fuel cap facing up.

2. Remove the fuel cap.

3. Place the fuel container spout into the fill hole on the fuel tank

and fill the tank.

NOTE: Do not overfill the tank.

4. Wipe up any fuel that may have spilled.

5. Reinstall the fuel cap.

6. Move the unit at least 30 ft. (9.1 m) from the fuel container and

the fueling site before starting the engine.

OIL AND FUEL MIXING INSTRUCTIONS

The use of old and/or improperly mixed fuel is the most common cause

of performance problems. Use only fresh, clean unleaded gasoline.

Follow the instructions carefully for the proper gasoline/oil mixture.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and oxygenates such as

ethanol, methanol or MTBE (ether). Alcohol-blended fuel absorbs

water. As little as 1% water in the fuel can make fuel and oil

separate, forming acids when stored. ALWAYS use fresh fuel (less

than 30 days old).

NOTE: Dispose of old fuel according to federal, state and local

regulations.

Using Blended Fuels

If using a blended fuel:

• Always use the fresh fuel mix explained in your operator's manual

• Use the fuel additive STA-BIL® or an equivalent

• Always agitate the fuel mix before fueling the unit

• Drain the tank and run the engine dry before storing the unit

Using Fuel Additives

The bottle of 2-cycle oil provided with this unit contains a fuel

additive to help inhibit corrosion and minimize gum deposits.

Always use the brand of 2-cycle oil that came with this unit. If this is

unavailable, use a 2-cycle oil designed for air-cooled engines and

mix it with a fuel additive, such as STA-BIL Fuel Stabilizer or an

equivalent. Add 0.8 oz. (23 ml) of fuel additive per gallon of fuel,

according to the instructions on the container. NEVER add fuel

additives directly to the unit's fuel tank.

Mixing the Fuel

NOTE: This unit comes with a 3.2 oz. bottle of 2-cycle oil. To obtain

the correct fuel mixture described below, pour the entire bottle

into one gallon of unleaded gasoline.

Thoroughly mix the proper ratio of unleaded gasoline with 2-cycle

engine oil. Do not mix them directly in the unit’s fuel tank. Use a

separate fuel can. Use a 40:1 gasoline/oil ratio. See the table below

for specific gasoline and oil mixing ratios.

Unleaded gasoline 2-cycle oil

1 gallon U.S.

(3.8 liters)

3.2 fl. oz.

(95 ml)

1 liter 25 ml

MIXING RATIO - 40:1

CAUTION:

For proper engine operation and maximum

reliability, pay strict attention to the gasoline and oil mixing

instructions on the 2-cycle oil bottle. Using improperly

mixed fuel can severely damage the engine.

WARNING:

Gasoline is extremely flammable. Ignited

vapors may explode. Always stop the engine and allow it

to cool before filling the fuel tank. Do not smoke while

filling the tank. Keep sparks and open flames at a distance

from the area.

WARNING:

Remove the fuel cap slowly to avoid injury

from fuel spray. Never operate the unit without the fuel cap

securely in place.

WARNING:

Add fuel in a clean, well ventilated outdoor

area. Wipe up any spilled fuel immediately. Avoid creating

a source of ignition for spilled fuel. Do not start the engine

until fuel vapors dissipate.

WARNING:

DO NOT USE E85 FUEL IN THIS UNIT. It

has been proven that fuel containing greater than 10%

ethanol will likely damage this engine and void the warranty.

STARTING AND STOPPING

WARNING:

Operate this unit only in a well-ventilated

outdoor area. Carbon monoxide exhaust fumes can be

lethal in a confined area.

WARNING:

Avoid accidentally starting the unit. To avoid

serious injury, the operator and the unit must be in a stable

position when pulling the starter rope (Fig. 9).

STARTING INSTRUCTIONS

1. Mix gasoline with oil. Refer to Oil and Fuel Mixing Instructions.

2. Fill the fuel tank. Refer to Fueling the Unit.

NOTE: There is no need to turn the unit on. The On/Off switch is in

the ON ( I ) position at all times (Fig. 6).

3. Slowly press and release the primer bulb 10 times (Fig. 7). If fuel

cannot be seen in the primer bulb, press and release the primer

bulb until fuel is visible.

4. Flip the choke lever clockwise until it clicks (Fig. 8).

5. Crouch in the starting position (Fig. 9).

6. DO NOT squeeze the throttle control (Fig. 6). Pull the starter

rope with a controlled and steady motion until the unit starts

(Fig. 9).

7. Idle the engine for 5 to 10 seconds. If the unit stops during this

time, squeeze the throttle control and pull the starter rope in a

controlled and steady motion until the unit starts.

8. Squeeze and hold the throttle control. Allow the engine to warm

up for 30 to 60 seconds.

NOTE: The engine is properly warmed up when it accelerates

without hesitation.

IF... the engine does not start, begin the starting procedure with

step 3.

IF... the unit is hot and fails to start within 3 pulls of the starter rope,

squeeze the throttle control and pull the starter rope with a

controlled and steady motion until the unit starts.

STOPPING INSTRUCTIONS

1. Release the throttle control and allow the engine to idle.

2. Press and hold the On/Off switch in the OFF (O) position until

the engine comes to a complete stop (Fig. 6).

Fig. 6

On ( I ) / Start

Off (O) / Stop

Throttle Control

Fig. 9

Starting

Position

Starter Rope Grip

Fig. 7

Primer Bulb

Fig. 8

Choke Lever

OPERATION

HOLDING THE UNIT

• Stand in the operating position (Fig. 10).

• Hold the shaft grip with the right hand. Keep the right arm

slightly bent.

• Hold the handle with the left hand. Keep the left arm straight.

• Hold the unit at waist level.

• Keep the cutting head parallel to the ground so that it easily

contacts the grass without the need for bending over.

WARNING:

Always wear eye, hearing, hand, foot and

body protection to reduce the risk of injury when operating

this unit.

TIPS FOR BEST RESULTS

• Keep the cutting head parallel to the ground.

• Cut from left to right whenever possible. This improves the unit's

cutting efficiency and throws clippings away from the operator.

• Do not trim wet grass or weeds.

NOTE: Some line breakage will occur from:

• Entanglement with foreign matter

• Normal line fatigue

• Attempting to cut thick vegetation

• Forcing the line into objects such as walls or fence posts

DECORATIVE TRIMMING

When trimming around trees, posts, fences, etc., rotate the whole

unit so that the cutting head is at a 30° angle to the ground (Fig. 11).

Fig. 10

Fig. 11

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the frequency

stated in the table. These procedures should also be a part of any

seasonal tune-up.

NOTE: Some maintenance procedures may require special tools or

skills. If you are unsure about these procedures, take the unit to

an MTD authorized service dealer.

NOTE: Maintenance, replacement, or repair of the emission control

devices and system may be performed by an MTD authorized

service dealer.

NOTE: Please read the California/EPA statement that came with the

unit for a complete listing of terms and coverage for the emissions

control devices, such as the spark arrestor, muffler, carburetor, etc.

WARNING:

To prevent serious injury, never perform

maintenance or repairs while the unit is running. Always

allow the unit to cool before servicing or repairing the unit.

Disconnect the spark plug wire to prevent the unit from

starting accidentally.

MAINTENANCE

FREQUENCY MAINTENANCE REQUIRED

Every 10 hours • Clean and re-oil the air filter. Refer to

Maintaining the Air Filter.

Every 25 hours • Check the spark plug condition and gap.

Refer to Maintaining the Spark Plug.

Fig. 12

Fig. 13

Fig. 14

Line

Holes

Cutting Head

Positioning

Tunnel

Positioning

Tunnel

Line

Fig. 15

Line

Cutting Head

REPLACING THE TRIMMING LINE

Only use the trimming line described in the Specifications section.

Other types of trimming line may cause the engine to overheat or fail.

1. Remove the old line from the cutting head.

2. Use a clean cloth to clean the surface of the cutting head.

3. Insert the ends of the line through the circular holes in the side

of the cutting head (Fig. 12). Push the line through the holes until

both ends protrude from the positioning tunnels (Fig. 13).

4. Pull the ends of the line until the line is tight against the cutting

head. Make sure the ends of the line are of equal length (Fig. 14).

If one end is longer than the other, push the longer end back

through the cutting head partway and pull the shorter end out. If

necessary, repeat this process until both ends are of equal length.

5. Press the exposed trimming line between the circular holes until

it lies flat against the cutting head (Fig. 15).

WARNING:

Never use metal-reinforced line, wire, chain or

rope. These can break off and become dangerous projectiles.

MAINTAINING THE AIR FILTER

Failure to maintain the air filter can result in poor performance or can

cause permanent damage to the engine. Engine failure due to

improper air filter maintenance is not covered by the product warranty.

Cleaning the Air Filter

1. Open the air filter cover: press in the lock tab and swing the air

filter cover to the right (Fig. 16).

2. Remove the air filter from inside the air filter cover (Fig. 16).

3. Wash the air filter in detergent and water. Rinse the air filter

thoroughly and allow it to dry.

4. Lightly coat the air filter with clean SAE 30 oil.

5. Squeeze the air filter to spread and remove excess oil.

6. Reinstall the air filter inside the air filter cover (Fig. 16).

NOTE: Operating the unit without the air filter and air filter cover will

VOID the warranty.

7. Close the air filter cover: swing the air filter cover to the left and

press it closed until the lock tab snaps into place (Fig. 16).

WARNING:

To avoid serious personal injury, always stop

the engine and allow it to cool before cleaning or maintaining

the unit.

Fig. 16

Air Filter

Air Filter Cover

Lock Tab

ADJUSTING THE IDLE SPEED

NOTE: Careless adjustments can seriously damage the unit. A qualified

service dealer should make carburetor adjustments.

If, after checking the fuel and cleaning the air filter, the engine still

will not idle, adjust the idle speed screw as follows:

1. Start the engine. Refer to Starting and Stopping.

2. Release the throttle control and let the engine idle. If the engine

stops, use a small Phillips screwdriver to turn the idle speed screw

clockwise, 1/8 of a turn at a time (as needed) until the engine idles

smoothly (Fig. 17).

3. If the engine is idling too quickly, turn the idle speed screw

counterclockwise, 1/8 of a turn at a time (as needed) to reduce the

idle speed (Fig. 17).

Checking the fuel, cleaning the air filter, and adjusting the idle speed

should solve most engine problems. If not, and any of the following

conditions are true, take the unit to a qualified service dealer:

• the engine will not idle

• the engine hesitates or stalls on acceleration

• there is a loss of engine power

WARNING:

The cutting head may spin during idle speed

adjustments. Wear protective clothing and observe all

safety instructions to prevent serious personal injury.

Fig. 17

Idle Speed Screw

Fig. 18

0.025 in.

(0.635 mm)

MAINTAINING THE SPARK PLUG

1. Stop the engine and allow it to cool. Grasp the spark plug boot

firmly and pull it from the spark plug.

2. Clean around the spark plug. Remove the spark plug from the

cylinder head with a 5/8-inch socket, turning counterclockwise.

3. Inspect the spark plug. If the spark plug is cracked, fouled or

dirty, replace it with a replacement part #753-06193, a

Champion RDJ7J or an equivalent spark plug.

4. Use a feeler gauge to set the air gap at 0.025 in. (0.635 mm)

(Fig. 18).

5. Install the spark plug in the cylinder head. Tighten the spark plug

with a 5/8-inch socket, turning it clockwise until snug.

NOTE: If using a torque wrench, torque to:

110-120 in.•lb. (12.3-13.5 N•m). Do not over tighten.

6. Reattach the spark plug boot.

WARNING:

Do not sand blast, scrape or clean spark plug

electrodes. Grit in the engine could damage the cylinder.

CLEANING AND STORAGE

CLEANING

Use a small brush to clean the outside of the unit. Do not use strong

detergents. Household cleaners that contain aromatic oils such as

pine and lemon, and solvents such as kerosene, can damage

plastic. Wipe off any moisture with a soft cloth.

STORAGE

• Never store a fueled unit where fumes may reach an open flame

or spark.

• Allow the engine to cool before storing.

• Lock up the unit to prevent unauthorized use or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

Short-term Storage (1-2 weeks)

1. Store the unit in a horizontal position. If this is not possible, store

the unit vertically with the engine at the top.

Long-term Storage

1. Remove the fuel cap, tip the unit and drain the fuel into an

approved container. Reinstall the fuel cap.

2. Start the engine and allow it to run until it stalls. This ensures

that all fuel has been drained from the carburetor.

3. Allow the engine to cool. Remove the spark plug and put 5

drops of any high quality motor oil or 2-cycle oil into the cylinder.

Pull the starter rope slowly to distribute the oil. Reinstall the

spark plug.

4. Thoroughly clean the unit and inspect it for any loose or

damaged parts. Repair or replace damaged parts and tighten

loose screws, nuts or bolts.

Preparing the Unit for Use after Long-term Storage

1. Remove the spark plug and drain all of the oil from the cylinder.

NOTE: Do not use fuel that has been stored for more than 30 days.

Dispose of old fuel according to federal, state and local regulations.

WARNING:

To avoid serious personal injury, always stop

the engine and allow it to cool before cleaning or maintaining

the unit.

If further assistance is required, contact an authorized service dealer.

The fuel tank is empty Fill the fuel tank with properly mixed fuel

The primer bulb was not pressed enough Press the primer bulb 10 times or until fuel is visible

The engine is flooded

Squeeze the throttle control and pull the starter rope until the engine

starts

The fuel is old (over 30 days) and/or improperly mixed Drain the fuel tank and add fresh, properly mixed fuel

The spark plug is fouled Replace the spark plug

TROUBLESHOOTING

The fuel is old (over 30 days) and/or improperly mixed Drain the fuel tank and add fresh, properly mixed fuel

The cutting head is bound with grass Stop the engine and clean the cutting head

The air filter is dirty Clean or replace the air filter

PROBLEM SOLUTION

The air filter is dirty Clean or replace the air filter

The fuel is old (over 30 days) and/or improperly mixed Drain the fuel tank and add fresh, properly mixed fuel

The idle speed is incorrect Adjust the idle speed

The fuel is old (over 30 days) and/or improperly mixed Drain the fuel tank and add fresh, properly mixed fuel

The air filter is dirty Clean or replace the air filter

The spark plug is fouled Replace the spark plug

THE ENGINE WILL NOT START

THE ENGINE WILL NOT IDLE

THE ENGINE WILL NOT ACCELERATE

THE ENGINE LACKS POWER OR STALLS

The limited warranty set forth below is given by MTD LLC (MTD) with respect to new merchandise purchased and used in the United States,

its possessions and territories.

MTD warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original

purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship. This limited

warranty shall only apply if this product has been operated and maintained in accordance with the Operator’s Manual furnished with the

product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft,

fire, water or damage because of other peril or natural disaster. Damage resulting from the installation or use of any accessory or attachment

not approved by MTD for use with the product(s) covered by this manual will void your warranty as to any resulting damage. This warranty is

limited to ninety (90) days from the date of original retail purchase for any MTD product that is used for rental or commercial purposes, or

any other income-producing purpose.

HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF PURCHASE THROUGH YOUR LOCAL AUTHORIZED SERVICE

DEALER. To locate the dealer in your area, visit our website at www.mtdproducts.com or www.mtdproducts.ca, check for a listing in the

Yellow Pages, call 1-800-800-7310 or 1-800-668-1238 in Canada, or write to P.O. Box 361131, Cleveland, OH 44136-0019. No product returned

directly to the factory will be accepted unless prior written permission has been extended by the Customer Service Department of MTD.

This limited warranty does not provide coverage in the following cases:

A. Tune-ups - Spark Plugs, Carburetor Adjustments, Filters

B. Wear items - Bump Knobs, Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts, Saw Chains, Guide Bars,

Cultivator Tines, Blades.

C. MTD does not extend any warranty for products sold or exported outside of the United States of America, its possessions and territories,

except those sold through MTD’s authorized channels of export distribution.

MTD reserves the right to change or improve the design of any MTD Product without assuming any obligation to modify any product

previously manufactured.

No implied warranty, including any implied warranty of merchantability or fitness for a particular purpose, applies after the

applicable period of express written warranty above as to the parts as identified. No other express warranty or guaranty, whether

written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any product

shall bind MTD. During the period of the Warranty, the exclusive remedy is repair or replacement of the product as set forth above.

(Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)

The provisions as set forth in this Warranty provide the sole and exclusive remedy arising from the sales. MTD shall not be liable for

incidental or consequential loss or damages including, without limitation, expenses incurred for substitute or replacement lawn

care services, for transportation or for related expenses, or for rental expenses to temporarily replace a warranted product. (Some

states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)

In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold. Alteration of the safety features

of the product shall void this Warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others

and their property arising out of the use or misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the original purchaser, original lessee or the person for whom it was purchased

as a gift.

How State Law Relates to this Warranty: This warranty gives you specific legal rights, and you may also have other rights which vary from

state to state.

To locate your nearest service dealer, dial 1-800-800-7310 in the United States or 1-800-668-1238 in Canada.

MTD LLC

P.O. Box 361131

Cleveland, OH 44136-0019

MANUFACTURER’S LIMITED WARRANTY FOR:

769-08353 / 00 08/12

Manuel de l’opérateur

Taille-bordure à 2 temps

TABLE DES MATIÈRES

Service technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Apprenez à connaître votre appareil . . . . . . . . . . . . . . . . . . . . . . .21

Caractéristiques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Assemblage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Huile et carburant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Mise en marche et arrêt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Utilisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Entretien . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Nettoyage et entreposage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Toutes les informations, illustrations et caractéristiques contenues

dans ce manuel reposent sur les dernières informations disponibles

sur ce produit à la date d’impression. Nous nous réservons le droit

d’apporter à tout instant des modifications, sans préavis.

NE RAMENEZ PAS CET APPAREIL CHEZ LE

REVENDEUR. UNE PREUVE D’ACHAT SERA EXIGÉE

POUR AVOIR RECOURS À LA GARANTIE.

Pour obtenir de l’aide concernant l’assemblage, les commandes,

l’utilisation ou l’entretien de cet appareil, veuillez contacter le service

à la clientèle au 1-800-800-7310 (États-Unis) ou au 1-800-668-1238

(Canada). Pour obtenir des informations supplémentaires sur cet

appareil, visitez le site Internet : www.mtdproducts.com (É.-U.) ou

www.mtdproducts.ca (Canada).

Pour profiter du service technique, veuillez appeler le service à la

clientèle pour obtenir une liste des centres de réparation agréés les

plus proches. Les réparations de cet appareil doivent être confiées

uniquement à un centre de réparation agréé, à la fois pendant et

après la période de garantie. Lors d’une réparation, utilisez

uniquement des pièces de rechange identiques.

CONSERVEZ CES INSTRUCTIONS

SERVICE TECHNIQUE

SÉCURITÉ

NOTE SUR LE PARE-ÉTINCELLES

REMARQUE : à l’intention des utilisateurs sur les terrains

forestiers américains et dans les États de Californie, du Maine,

de l’Oregon et de Washington. Tous les services des forêts

américains et les États de Californie (codes des ressources

publiques 4442 et 4443), de l’Oregon et de Washington exigent, au

titre de la loi, que certains moteurs à combustion interne utilisés

dans les broussailles de forêt et/ou les zones recouvertes d’herbe

soient équipés d’un pare-étincelles, soient maintenus en bon état

de marche, ou soient construits, équipés et entretenus en vue

d’éviter tout risque d’incendie. Veuillez contacter les autorités

nationales ou locales pour connaître les réglementations à cet

égard. Le non-respect de ces exigences pourrait impliquer votre

responsabilité ou entraîner une amende. Cet appareil est équipé

en usine d’un pare-étincelles. Si ce dernier doit être remplacé,

veuillez consulter votre CENTRE DE RÉPARATION LOCAL pour

installer le pot d’échappement réf. 753-06418.

Veuillez lire le manuel de l’opérateur et respecter tous les

avertissements et consignes de sécurité. Dans le cas contraire,

l’opérateur et/ou les passants peuvent subir des blessures graves.

SYMBOLE SIGNIFICATION

AVERTISSEMENT :

indique un danger GRAVE.

Le non-respect d’un symbole d’AVERTISSEMENT PEUT

provoquer des blessures graves de l’opérateur ou d’autres

personnes.

ATTENTION :

indique un danger MODÉRÉ.

Le non-respect d’un symbole ATTENTION POURRAIT

provoquer des blessures ou des dommages des biens de

l’opérateur ou d’autres personnes.

Les symboles de sécurité visent à attirer votre attention sur les

dangers éventuels. Vous devez accorder une attention particulière

aux symboles de sécurité afin de bien les comprendre. Les

avertissements de sécurité n’éliminent pas les dangers en eux-

mêmes. Les instructions ou mises en garde ne remplacent en rien

les mesures de prévention appropriées contre les accidents.

REMARQUE : vous donne des informations ou des consignes

essentielles pour l’utilisation ou l’entretien de l’équipement.

DANGER :

indique un danger EXTRÊME.

Le non-respect d’un symbole de DANGER ENTRAÎNERA

des blessures graves, voire un décès, de l’opérateur ou

d’autres personnes.

PROPOSITION 65 DE L’ÉTAT DE CALIFORNIE

AVERTISSEMENT :

les gaz d’échappement, certains

de leurs constituants et certains composants finis

contiennent ou émettent des produits chimiques reconnus

par l’État de Californie comme étant à l’origine de cancers

ou de malformations congénitales ou autres dangers pour

la reproduction. Lavez-vous les mains après avoir

manipulé l’appareil.

VEUILLEZ LIRE TOUTES LES INSTRUCTIONS AVANT

• Veuillez lire soigneusement ces instructions. Familiarisez-vous

avec les commandes et l’utilisation correcte de l’appareil.

• N’utilisez pas cet appareil quand vous êtes fatigué, malade ou sous

l’influence de boissons alcoolisées, de drogues ou de médicaments.

• Les enfants ne doivent pas utiliser cet appareil. Les adolescents

doivent être supervisés par des adultes.

• Tous les carters et dispositifs de sécurité doivent être

correctement installés avant l’utilisation de cet appareil.

• Inspectez l’appareil avant l’utilisation. Remplacez les pièces

endommagées. Détectez les fuites de carburant éventuelles.

Assurez-vous que toutes les fixations sont en place et bien

serrées. Remplacez les pièces fissurées, ébréchées ou

endommagées d’une manière ou d’une autre. N’utilisez pas

l’appareil quand des pièces sont desserrées ou endommagées.

• Utilisez uniquement le fil de coupe décrit dans la section

Caractéristiques de ce manuel. N’utilisez jamais de fils, de

câbles, de chaînes ou de cordons à renfort métallique. Ils

peuvent se casser et se transformer en projectiles dangereux.

• Vous devez être conscient des risques de blessures à la tête,

aux mains et aux pieds.

• Inspectez attentivement la zone de travail avant de démarrer

l’appareil. Retirez les pierres, le verre cassé, les clous, les fils, les

ficelles et autres objets qui peuvent être projetés ou s’enrouler

dans l’appareil.

• Éloignez les enfants, les passants et les animaux domestiques ;

ils doivent rester dans un rayon d’au moins 15 mètres (50 pieds).

Même à cette distance, il existe néanmoins un risque de

projectiles pour les personnes à proximité. Encouragez-les à

porter des lunettes de sécurité. Si quelqu’un s’approche de

vous, arrêtez immédiatement l’appareil.

• Appuyez sur la manette des gaz et vérifiez qu’elle revient

automatiquement à la position de ralenti. Effectuez tous les

réglages ou réparations avant d’utiliser l’appareil.

PENDANT L’UTILISATION

• Portez des lunettes de sécurité conformes aux normes ANSI Z87.1

en vigueur et marquées comme telles. Portez une protection

auditive pendant l’utilisation de cet appareil. Portez un écran facial

ou un masque antipoussières si la tâche est poussiéreuse.

• Portez un pantalon long et épais, des bottes, des gants et une

chemise à manches longues. Ne portez pas des vêtements

amples, des bijoux, un pantalon court, des sandales et ne travaillez

pas pieds nus. Attachez vos cheveux au-dessus des épaules.

• Le carter de la tête de coupe doit toujours être en place pendant

l’utilisation de l’appareil. N’utilisez pas l’appareil sans que les

deux fils de coupe soient tendus et que le fil correct soit installé.

Ne tirez pas le fil de coupe au-delà du carter de protection.

• Cet appareil est doté d'un embrayage. La tête de coupe reste

immobile quand le moteur tourne au ralenti. Si ce n'est pas le

cas, apporter l'appareil à un centre de réparation agréé pour

obtenir un ajustement.

• Réglez la poignée afin d’avoir la meilleure prise en main.

• Assurez-vous que la tête de coupe n’est pas en contact avec

tout autre élément avant de démarrer l’appareil.

• Utilisez l’appareil uniquement en plein jour ou avec un bon

éclairage artificiel.

• Évitez tout démarrage accidentel. Placez-vous dans la position de

démarrage dès que vous tirez sur le câble de démarreur. L’opérateur

et l’appareil doivent être dans une position stable pendant le

démarrage. Consultez les sections Mise en marche et Arrêt.

• Utilisez le bon outil. Utilisez uniquement cet outil pour l’usage prévu.

• Tenez toujours l’appareil à deux mains lorsqu’il est en marche.

Tenez fermement les deux anses ou poignées.

• Ne vous penchez pas trop en avant. Conservez toujours une

position stable et un bon équilibre. Montrez-vous très prudent

quand vous travaillez sur des pentes raides.

• Éloignez vos mains, votre visage et vos pieds des pièces

mobiles. Ne touchez pas ou n’essayez pas d’arrêter des pièces

en mouvement.

• Ne touchez pas le moteur, le carter d’engrenage ou le pot

d’échappement. Ces composants deviennent extrêmement

chauds pendant l’utilisation, même après l’arrêt de l’appareil.

• N’utilisez pas l’appareil à une vitesse supérieure à celle

nécessaire pour réaliser le travail. Ne faites pas fonctionner

l’appareil à haute vitesse quand vous ne l’utilisez pas.

• Ne forcez pas l’appareil. Il sera plus efficace et plus sûr si vous

l’utilisez à la vitesse pour laquelle il a été conçu.

• Arrêtez toujours l’appareil quand le travail est interrompu ou

quand vous vous déplacez d'un endroit à un autre.

• Si vous heurtez ou enroulez un objet étranger dans l’appareil,

arrêtez immédiatement l’appareil et vérifiez les dommages

éventuels. Ne redémarrez pas l’appareil avant de l’avoir réparé.

N’utilisez pas l’appareil quand des pièces sont desserrées ou

endommagées.

• Arrêtez le moteur et débranchez la bougie pour les tâches

d’entretien ou les réparations.

AVERTISSEMENTS DE SÉCURITÉ POUR LES APPAREILS

À GAZ

• Stockez le carburant uniquement dans des récipients

spécifiquement conçus à cet usage et approuvés pour le

stockage de telles substances.

• Arrêtez toujours le moteur et laissez-le refroidir avant de remplir

le réservoir d’essence. N’enlevez jamais le bouchon du réservoir

de carburant ou ne remplissez jamais ce dernier quand le

moteur est chaud. Dévissez toujours lentement le bouchon du

réservoir de carburant afin de relâcher toute pression présente

avant de le remplir.

• Mélangez et ajoutez toujours le carburant dans une zone

extérieure propre et bien aérée, en l’absence totale d’étincelles

ou de flammes. NE fumez PAS.

• N’utilisez jamais l’appareil quand le bouchon du réservoir de

carburant n’est pas correctement vissé.

• CONSIGNES DE SÉCURITÉ IMPORTANTES •

AVERTISSEMENT :

quand vous utilisez l’appareil,

vous devez respecter toutes les règles de sécurité. Veuillez

lire ces consignes avant d’utiliser l’appareil pour assurer la

sécurité de l’opérateur et de tous les passants. Veuillez

conserver ces instructions pour référence ultérieure.

AVERTISSEMENT : l’essence est extrêmement

inflammable et ses vapeurs peuvent exploser en présence

d’une source d’inflammation. Prenez les précautions

suivantes :

• Évitez de créer une source d’inflammation en présence d’un

déversement de carburant. Essuyez immédiatement tout carburant

échappé du réservoir avant de démarrer l’appareil. Éloignez

l’appareil à 9,1 mètres (30 pieds) au moins de la source de

ravitaillement et du site avant de démarrer le moteur. NE fumez PAS.

• Ne démarrez jamais ou n’utilisez jamais l’appareil à l’intérieur

d’un espace ou d’un bâtiment clos. L’inhalation des fumées

d’échappement peut tuer. Utilisez cet appareil uniquement dans

une zone extérieure bien aérée.

• SYMBOLES DE SÉCURITÉ ET INTERNATIONAUX •

Le présent manuel de l’opérateur décrit les symboles et pictogrammes de sécurité et internationaux, susceptibles d’apparaître sur ce

produit. Veuillez lire le manuel de l’opérateur pour connaître les informations complètes sur la sécurité, l’assemblage, l’utilisation, l’entretien

et la réparation.

SYMBOLE SIGNIFICATION SYMBOLE SIGNIFICATION

• SYMBOLE D’ALERTE DE SÉCURITÉ

Indique un danger, un avertissement ou une mise en

garde. Peut être utilisé conjointement avec d’autres

symboles ou pictogrammes.

• LISEZ LE MANUEL DE L’OPÉRATEUR

AVERTISSEMENT : veuillez lire le(s) manuel(s) de

l’opérateur et respecter tous les avertissements et

consignes de sécurité. Dans le cas contraire,

l’opérateur et/ou les passants peuvent subir des

blessures graves.

• PORTEZ DES PROTECTIONS AUDITIVES ET

OCULAIRES

AVERTISSEMENT : la projection d’objets et les

bruits forts peuvent provoquer des blessures oculaires

graves et une perte auditive. Portez une protection

oculaire conforme aux normes ANSI Z87.1 en vigueur,

ainsi qu’une protection auditive pendant l’utilisation

de cet appareil. Utilisez un écran facial complet dès

que nécessaire.

• ESSENCE SANS PLOMB

Utilisez toujours de l’essence sans plomb, propre et

neuve.

• HUILE

Consultez le manuel de l’opérateur pour connaître le

type d’huile à utiliser.

• N’UTILISEZ PAS UN CARBURANT E85 DANS CET

APPAREIL

AVERTISSEMENT : il a été prouvé qu’un carburant

contenant plus de 10 % d’éthanol est susceptible

d’endommager ce moteur et d’annuler la garantie.

• COMMANDE DE MARCHE/ARRÊT

ALLUMAGE / DÉMARRAGE / MARCHE

• COMMANDE DE MARCHE/ARRÊT

ARRÊT

• POIRE D’AMORÇAGE

Poussez complètement et lentement la poire

d’amorçage à 10 reprises.

• LES OBJETS PROJETÉS ET LA TÊTE ROTATIVE

PEUVENT PROVOQUER DES BLESSURES GRAVES

AVERTISSEMENT : les petits objets peuvent être

propulsés à des vitesses élevées, provoquant des

blessures. Tenez-les à l’écart du rotor en mouvement.

• ÉLOIGNEZ LES PASSANTS

AVERTISSEMENT : éloignez tous les passants,

en particulier les enfants et les animaux domestiques,

à 15 m (50 pieds) au moins de la zone de coupe.

• SURFACE CHAUDE

AVERTISSEMENT : ne touchez pas un pot

d’échappement ou un cylindre chaud. Vous pourriez

vous brûler. Ces éléments chauffent énormément

lorsque l’appareil est en marche. Ils restent chauds

pendant un court instant après l’arrêt.

• LAME TRANCHANTE

AVERTISSEMENT : lame tranchante sur le carter de

protection de l’accessoire de coupe. Pour éviter toute

blessure grave, ne touchez pas la lame du coupe-fil.

AUTRES AVERTISSEMENTS DE SÉCURITÉ

• Toutes les procédures d’entretien, autres que celles décrites

dans ce manuel, doivent être réalisées par un revendeur agréé.

• Avant une inspection, un entretien, un nettoyage, un entreposage,

un transport ou le remplacement d’une pièce de l’appareil :

1. Arrêtez l’appareil.

2. Assurez-vous que toutes les pièces mobiles se sont arrêtées.

3. Laissez l’appareil refroidir.

4. Débranchez le fil de la bougie.

• Assurez-vous que l’appareil est sécurisé pour les transports.

• Quand le réservoir contient du carburant, ne rangez jamais

l’appareil à l’intérieur d’un bâtiment où des vapeurs d’essence

pourraient atteindre une flamme nue (veilleuses, etc.) ou des

étincelles (interrupteurs, moteurs électriques, etc.).

• Rangez l’appareil dans un endroit sec et sûr ou en hauteur pour

éviter une utilisation non autorisée ou des dommages. Gardez

toujours l’appareil hors de portée des enfants.

• Ne mouillez pas ou n’éclaboussez pas l’appareil avec de l’eau ou

tout autre liquide. Les poignées doivent rester sèches, propres et

dépourvues de tout dépôt. Nettoyez l’appareil après chaque

utilisation. Consultez la section Nettoyage et entreposage.

• Conservez ces instructions. Consultez-les souvent et utilisez-les

pour former d’autres utilisateurs. Si vous prêtez cet appareil à

d’autres personnes, remettez-leur également ces instructions.

CONSERVEZ CES INSTRUCTIONS

• Utilisez uniquement des pièces et des accessoires de rechange

du fabricant d’origine pour cet appareil. Ils sont disponibles

auprès de votre centre de réparation agréé. L’utilisation d’autres

pièces ou accessoires pourrait entraîner de graves blessures de

l’utilisateur ou endommager l’appareil, et annuler la garantie.

• L’appareil doit rester propre. Retirez avec précaution la végétation

et autres débris qui pourraient bloquer les pièces mobiles.

• Pour réduire les risques d’incendie, remplacez un pot

d’échappement et un pare-étincelles défectueux. Nettoyez l’herbe,

les feuilles, les couches de graisse excessives ou les dépôts de

carbone présents sur le moteur et le pot d’échappement.

• Si l’appareil commence à vibrer de façon anormale, arrêtez-le

immédiatement. Inspectez l’appareil pour découvrir l’origine des

vibrations. Les vibrations indiquent en général un problème.

La page charge ...

Murray MS2560 Manuel utilisateur

Marque: Murray

Modèle: MS2560

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Murray MS2560 User manual
español: Murray MS2560 Manual de usuario

Murray MS2560 Manuel utilisateur

Murray MS2560 Manuel utilisateur

dans d''autres langues

Autres documents