Simplicity MANUAL, OPS, ESPV21675 Manuel utilisateur

Operator's Manual

Manual No. 7104268 (Rev. ‘-’, 2/4/2010)

WALK BEHIND MOWER

EUROPEAN MODEL

ESPV21675

Model No

7800253

7800688

Not for

Reproduction

Thank You for purchasing this quality-built Snapper mower. We’re pleased that you placed your

confidence in the Snapper brand. When operated and maintained according to the instructions in this

manual, your Snapper mower will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with the

machine and how to avoid them. This machine is designed and intended only for finish cutting of

established lawns and is not intended for any other purpose. It is important that you read and understand

these instructions thoroughly before attempting to start or operate this equipment. Save these original

instructions for future reference.

PRODUCT REGISTRATION

IMPORTANT: KEEP THIS INFORMATION FOR YOUR PERSONAL RECORDS

(Complete the following information on your Snapper purchase)

Date of Purchase__________________________________________________________________

Retailer_________________________________________________________________________

Retailer's Phone Number___________________________________________________________

Equipment

Model Number______________________________________________________________

Serial Number ______________________________________________________________

Engine

Model_________________________Type__________________Trim___________________

Briggs & Stratton Yard Power Products Group

SNAPPER is a trademark of

Briggs & Stratton Power Products Group, LLC

Jefferson, WI, USA.

Not for

Reproduction

3

Operator Safety Features and Controls Operation Maintenance Troubleshooting Warranty

Table of Contents

Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Important Operator Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Decal Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Pre-Start Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Starting & Stopping Engine & Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Propelling Mower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Handle Height Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Cutting Height Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Recycling Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Installing the Discharge Deflector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Removing the Recycling Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Installing the Grass Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Change Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Check Mower Blade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Check Engine Drive Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Service - Periodic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Wheel Drive Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Storage Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Mower Blade Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Blade Sharpening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Wheel Drive Control Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Service Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Slope Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Not for

Reproduction

www.snapper.com4

Operator Safety

! !

IMPORTANT OPERATOR SAFETY INSTRUCTIONS

WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects

that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in

serious injury or death to the operator or other persons. The owner of the machine must understand these

instructions and must allow only persons who understand these instructions to operate machine. Each

person operating the machine must be of sound mind and body and must not be under the influence of any

substance, which might impair vision, dexterity or judgment. If you have any questions pertaining to your

machine which your dealer cannot answer to your satisfaction, call or write the Customer Service

Department at SNAPPER, McDonough, Georgia 30253. Phone: (1-800-935-2967).

PROTECTION FOR CHILDREN

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

machine and the mowing activity. Never assume that

children will remain where you last saw them.

1. KEEP children out of the mowing area and under the

watchful care of a responsible adult other than the operator.

2. DO NOT allow children in yard when machine is operated

and turn machine OFF if anyone enters the area.

3. DO NOT allow pre-teenage children to operate machine.

4. ALLOW only responsible adults & teenagers with mature

judgment under close adult supervision to operate machine.

5. DO NOT pull mower backwards unless absolutely

necessary. LOOK and SEE behind and down for children,

pets and hazards before and while backing.

6. USE EXTRA CARE when approaching blind corners,

shrubs, trees, or other objects that may obscure vision.

SLOPE OPERATION

1. Slopes are a major factor related to slip and fall

accidents, which can result in severe injury. All slopes

require extra caution. If you feel uneasy on a slope, DO NOT

mow it.

2. Mow across slopes, never up-and-down. Exercise

extreme CAUTION when changing directions on slopes. DO

NOT mow steep slopes or other areas where stability or

traction is in doubt. Refer to the Slope Guide at the back of

this manual.

3. Use extra care with grass catchers or other attachments;

these affect the handling and the stability of the machine.

PREPARATION

1. Read, understand, and follow instructions and warnings

in this manual and on the mower, engine and attachments.

Know the controls and the proper use of the mower before

starting.

2. Only mature, responsible persons shall operate the

machine and only after proper instruction.

3. Data indicates that operators age 60 and above, are

involved in a large percentage of mower-related injuries.

These operators should evaluate their ability to operate the

mower safely enough to protect themselves and others

from serious injury.

4. Handle fuel with extra care. Fuels are flammable and

vapors are explosive. Use only an approved fuel container.

DO NOT remove fuel cap or add fuel with engine running.

PREPARATION

(Continued From Previous Column)

Add fuel outdoors only with engine stopped and cool. Clean

spilled fuel and oil from machine. DO NOT smoke.

5. Check the area to be mowed and remove all objects such

as toys, wire, rocks, limbs and other objects that could

cause injury if thrown by blade or interfere with mowing.

Also note the location of holes, stumps, and other possible

hazards.

6. Keep people and pets out of the mowing area.

Immediately, STOP Blade, Stop engine and Stop mower if

anyone enters the area.

7. Check shields, deflectors, switches, blade controls and

other safety devices frequently for proper operation and

location.

8. Make sure all safety decals are clearly legible. Replace if

damaged.

9. Protect yourself when mowing and wear safety glasses,

long pants and substantial footwear. DO NOT mow

barefooted or with sandals.

10. Know how to STOP blade and engine quickly in

preparation for emergencies.

11. Use extra care when loading or unloading the machine

into a trailer or truck.

12. Check grass catcher components frequently for signs of

wear or deterioration and replace as needed to prevent

injury from thrown objects going through weak or torn

spots.

SAFE HANDLING OF GASOLINE

To avoid personal injury or property damage, use extreme

care in handling gasoline. Gasoline is extremely flammable

and the vapors are explosive.

1. Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

2. Use only an approved fuel container.

3. DO NOT remove fuel cap or add fuel with the engine

running. Allow the engine to cool before refueling.

4. DO NOT refuel the machine indoors.

5. DO NOT store the machine or fuel container inside where

there is an open flame, spark or pilot light such as on a

water heater or other appliances.

6. DO NOT fill fuel containers inside a vehicle or on a

truck or trailer bed with a plastic liner. Always place the

containers on the ground away from the vehicle before

filling.

Not for

Reproduction

5

Operator Safety

! !

IMPORTANT OPERATOR SAFETY INSTRUCTIONS (Continued)

SAFE HANDLING OF GASOLINE

(Continued From Previous Page)

7. Remove gas-powered equipment from the vehicle or

trailer and refuel it on the ground. If this is not possible,

then refuel equipment using a portable container, rather

than a gasoline dispenser nozzle.

8. DO NOT start gas powered equipment in enclosed

vehicles or trailers.

9. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. DO

NOT use a nozzle lock-open device

10. If fuel is spilled on clothing, change clothing

immediately.

11. DO NOT overfill a fuel tank. Replace fuel cap and tighten

securely.

OPERATION

1. DO NOT put hands or feet near or under rotating parts.

Keep clear of discharge area while engine is running.

2. STOP engine when crossing gravel drives, walks, or

roads, and under any conditions where thrown objects

might be a hazard.

3. Mow only in daylight or good artificial light.

4. DO NOT operate mower while under the influence of

alcohol or drugs.

5. After striking a foreign object or if mower vibrates

abnormally, STOP the engine, disconnect and secure spark

plug wire. Inspect the mower for any damage and repair the

damage before starting.

6. DO NOT mow near drop offs, ditches or embankments.

Operator could lose footing or balance.

7. STAY ALERT for holes and other hidden hazards. Tall

grass can hide obstacles. Keep away from ditches,

washouts, culverts, fences and protruding objects.

8. DO NOT mow on wet grass. Always be sure of your

footing. Keep a firm hold on the handle and walk, never run.

Slipping could cause injury.

9. ALWAYS stay behind handle when engine (motor) is

running.

10. DO NOT leave the machine with the engine running.

STOP BLADE and STOP ENGINE before leaving the

operators position for any reason.

11. Before cleaning, repairing or inspecting make certain

engine, blade and all moving parts have STOPPED.

Disconnect and secure spark plug wire away from plug to

prevent accidental starting.

12. STOP engine and wait until the blade comes to

complete STOP before removing grass bag and/or clearing

grass.

13. DO NOT operate mower without the entire grass

catcher, or guards in place discharge guard, rear guard or

other safety devices in place and working. DO NOT point

discharge at people, passing cars, windows or doors.

OPERATION

(Continued From Previous Column)

14. DO NOT discharge material against a wall or

obstruction. Material may ricochet back towards the

operator.

15. Slow down before turning.

16. Watch out for traffic when near or crossing roadways.

17. DO NOT operate engine in enclosed areas. Engine

exhaust gases contain carbon monoxide, a deadly poison.

18. Only use accessories approved by the manufacturer.

See manufacturer’s instructions for proper operation and

installation of accessories.

MAINTENANCE AND STORAGE

1. DO NOT store mower or fuel container inside where

fumes may reach an open flame, spark or pilot light such as

in a water heater, furnace, clothes dryer or other gas

appliance. Allow engine to cool before storing machine in

an enclosure. Store fuel container out of reach of children

in a well ventilated, unoccupied building.

2. Keep mower and engine free of grass, leaves or excess

grease to reduce fire hazard and engine overheating.

3. When draining fuel tank, drain fuel into an approved

container outdoors and away from open flame.

4. Keep all bolts, especially blade bolts, nuts and screws

properly tight. Check that all cotter pins are in proper

position.

5. Always provide adequate ventilation when running

engine. Engine exhaust gases contain carbon monoxide, a

deadly poison.

6. Service engine and make adjustments only when engine

is stopped. Removed spark plug wire from spark plug and

secure wire away from spark plug to prevent accidental

starting.

7. DO NOT change engine governor speed settings or

overspeed engine.

8. Check grass bag assembly frequently for wear or

deterioration to avoid thrown objects and exposure to

moving parts. Replace with new bag if loose seams or tears

are evident. Replace slider or bag adapter if broken or

cracked.

9. Mower blades are sharp and can cut. Wrap the blades or

wear heavy leather gloves and use CAUTION when handling

them.

10. DO NOT test for spark by grounding spark plug next to

spark plug hole; spark plug could ignite gas exiting engine.

11. Have machine serviced by an authorized SNAPPER

dealer at least once a year and have the dealer install any

new safety devices.

12. Use only genuine SNAPPER replacement parts to

assure that original standards are maintained.

Not for

Reproduction

www.snapper.com6

Operator Safety

DECAL IDENTIFICATION

(3) Warning Instructions:

A. Read, understand and follow instructions and warnings in

the operator’s manual, as well as on the mower, engine and

attachments before operating.

B. Indicates possible severe injury from rotating cutting blades.

C. Do not operate without entire grass catcher or guard in

place.

D. Keep children and others out of mowing area.

CA

DB

dB

Mfg. No. XXXXXXX

WALK BEHIND LAWN MOWER

S/N XXXXXXXXXX

SIMPLICITY MFG - SNAPPER

MCDONOUGH, GA 30253 USA

XX

2007

kg: XX

kW: X.XX

XXXX max

(1) Serial Tag:

A. Manufacturing (Part) Number

B. Description/Model Number

C. Serial Number

D. Manufacturer Information

E. Sound Power

F. Unit Mass

G. Kilowatts

H. Max RPM’s

I. Year of Manufacture

J. European Certification

E

A

F

D

B

C

G

H

JI

(2) Control Head Decal:

A. Engage/Fast

B. Slow/Disengage

B

A

(4) Height of Cut:

A. Low

B. High

B

A

Not for

Reproduction

7

Features and Controls

IMPORTANT

The figures and illustrations in this manual are provided

for reference only and may differ from your specific model.

Contact your Snapper dealer if you have questions.

Features and Controls

A. Oil Fill Cap and Dipstick

B. Fuel Filler Cap

C. Recycling Cover

D. Height Adjustment Lever

E. Blade Control

F. Rope Start Handle

G. Drive Wheel Control

H. Rear Discharge Door

I. Grass Bag

D

G

E

F

A

B

I

H

C

Not for

Reproduction

www.snapper.com8

Operation

Pre-Start Check List

Make the following checks and perform the service required

before each start-up.

1. Check the guards, deflectors, grass bag, and covers to

make sure all are in place and securely tightened.

2. Check the blade control (A, Figure 1) and wheel drive

control (B) to insure they work freely.

3. Check the cutting height. Adjust to the desired height.

Refer to the Section ‘Cutting Height Adjustment’.

4. Check the engine oil and add oil as needed to bring the

level up to the full mark (A, Figure 2). Refer to the

Engine Owner’s Manual for oil specifications.

5. Add fuel to the tank after pushing the mower outside

where fumes can safely dissipate. Fill the tank to 1-1/2

inches below the top of the filler neck (to allow for fuel

expansion). Make sure the cap is tightened after fueling.

Refer to the Engine Owners Manual for fuel

specifications.

6. Clean the exterior surfaces of the cutting deck and

engine of any accumulation of spilled fuel, dirt, grass,

oil, etc. Keep the engine air intake screen and cooling

fins clear at all times.

Starting and Operation

Engine and Blade

1. Pull the blade control (A, Figure 3) against the handle.

2. Start the mower: Pull the rope start handle (B) to crank

the engine.

3. After the engine starts, allow a brief warm-up until the

engine runs smooth before beginning mower operation.

NOTE:

To stop the engine (and blade), release the blade

control.

Figure 2: Checking engine oil

B

A

Figure 1: Mower controls

A

B

A

Figure 3: Starting the mower

Not for

Reproduction

9

Operation

Starting and Operation (Continued)

Propelling the Mower

1. Start the engine. Refer to the Section entitled “Starting

and Operation – Engine and Blade”.

2. Begin squeezing the wheel drive control (A, Figure 4)

back toward the handle to engage the wheel drive and

propel the mower forward. Forward speed can be

increased by squeezing the wheel drive control further

back toward the handle.

Stopping

1. Stop forward motion of the mower by releasing the

wheel drive control.

2. Stop the engine and blade by releasing the blade

control.

Handle Height Adjustment

The height of the mower handle can be adjusted as follows:

1. Turn the two locking cams (A, Figure 5) a quarter-turn to

unlock the handle assembly (B).

2. Align the handle assembly with one of the three handle

height adjustment holes (C) in the mounting brackets.

3. Return the locking cams to their original position to lock

the handle.

Figure 5: Adjusting the handle height

Figure 4: Wheel drive control

A

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

!!

(Components removed for clarity)

B

C

Not for

Reproduction

www.snapper.com10

Operation

Cutting Height Adjustment

1. Pull the height adjusting lever (A, Figure 6) outward, and

move to the desired cutting height. The highest cutting

position is Notch 9 (B; also see Figure 7). The lowest

cutting position is Notch 1 (C).

Note: The lever will set all wheels to the same cutting height.

Recycling Operation

Note:

For best recycling results, cut up to a maximum of 1/3

of grass blade length and recycle ONLY when grass is dry.

1. Set the height adjustment lever in the highest cutting

position (Notch 9). Refer to the Section entitled “Cutting

Height Adjustment”.

2. Proceed mowing slowly. If the grass is very dense,

lower the height adjustment lever one notch lower to

improve recycling performance.

Installing the Discharge Deflector

1. Raise the recycling cover (A, Figure 8).

Important:

The recycling cover should remain on the

machine at all times. Do not remove.

2. Install the deflector (B) to the deck under the recycling

cover, making sure that:

• The tabs (C) hook under the pivot rod (D).

• The locking tab on the deck (A, Figure 9) goes

through the slot in the deflector (B).

3. Lower the recycling cover against the deflector.

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

!!

WARNING

Stop engine and mower blade by releasing the blade

control before adjusting cutting height.

!!

Figure 6: Adjusting cutting height

4.00 in1.50 in

Figure 7: Cutting height settings (approximate)

B

C

Figure 8: Installing the discharge deflector

A

B

D

C

A

Not for

Reproduction

11

Operation

Removing the Recycling Plug

1. Raise the rear discharge door (A, Figure 10).

2. Remove the recycling plug (B) from the rear discharge

chute.

Note:

The recycling plug should be removed only when

bagging is desired, and should be replaced as soon as

bagging operations are completed.

Installing the Grass Bag

1. Raise the rear discharge door (A, Figure 11).

2. Remove the recycling plug. Refer to the section entitled

“Removing the Recycling Plug”.

3. Holding the grass bag handle (B), install the grass bag

onto the back of the mower, making sure that the grass

bag hooks (A, Figure 12) are hooked onto the rear door

pivot rod (B).

WARNING

Grass Catcher bags used on SNAPPER products are made

of woven fabric, and are subject to deterioration and wear

during normal usage. Check condition of bag before each

use. Immediately replace worn or damaged catcher bags

with only bags recommended by SNAPPER. The grass

catcher is optional equipment on some models.

!!

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

!!

Figure 10: Removing the recycling plug

Figure 11: Installing the grass bag

B

A

Figure 9: Deflector locking tab

A

B

A

B

Figure 12: Grass bag hooks

A

B

Not for

Reproduction

www.snapper.com12

Maintenance

Maintenance - Introduction

To retain the quality of the mower, use genuine SNAPPER

replacement parts only. Contact a local SNAPPER dealer for

parts and service assistance. For the correct part or

information for a particular mower, always mention the

model and serial number.

Service - After First 5 Hours

Change Engine Oil

1. Refer to the Engine Manual for proper oil specifications,

procedures and proper service intervals.

2. For the simplest/cleanest oil change, simply turn the

mower on its side to drain the oil, as shown. Drain the

oil through the dipstick tube (A, Figure 13) into a con-

tainer. Allow sufficient time for all the oil to drain.

Important: Drain the fuel tank before tipping the machine.

DO NOT tip the machine with the carburetor or spark plug

down. Oil from the crankcase will saturate the air filter and

cause the engine to be hard to start or not start at all. If

contamination does occur, the air filter will have to be

replaced.

3. Dispose of drain oil properly.

4. Fill the engine with oil as specified in the Engine Manual.

Do Not overfill.

Check Mower Blade

1. Disconnect the spark plug wire and secure the end away

from the plug.

2. Tilt the mower up on its rear wheels for access to the

blade cap screw (A, Figure 14). Do not tilt the mower

with the spark plug or carburetor down.

Important: Drain the fuel tank before tipping the mower. DO

NOT tip the machine with the carburetor or spark plug down.

Oil from the crankcase will saturate the air filter and cause

the engine to be hard to start or not start at all. If

contamination does occur, the air filter will have to be

replaced.

3. Check the torque of the blade cap screw. Recommended

torque should be 40 ft. lbs.

4. Check the blade for sharpness, wear and damage. Refer

to the Section entitled “Blade Wear Limits”.

Check Engine Drive Belt

1. Visually check the engine drive belt for cracking, fraying,

severed or exposed belt strands. If worn or damaged,

contact an authorized Snapper dealer for service before

operating the mower.

Service - Periodic

Perform all maintenance as described in the “Service

Schedule” section of this manual.

Engine

Service the engine according to the engine owner’s manual.

Air Filter

Refer to the engine owner’s manual for service instructions.

Engine Oil

Refer to the engine owner’s manual for service instructions.

Figure 13: Draining the engine oil

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

Wear heavy leather gloves when handling or working

around cutting blades. Blades are extremely sharp and can

cause severe injury.

!!

A

Figure 14: Tightening the blade cap screw

A

Not for

Reproduction

13

Maintenance

Wheel Drive Components

Clean any debris buildup on or around the transmission,

axles, idler, pulleys, belt, etc. Check components for wear or

damage. Replace worn or damaged components

immediately.

Storage Procedure

Refer to the Engine Owner’s Manual for directions regarding

engine storage preparations. Prepare the mower for “end of

season” storage as follows:

1. Drain the fuel from the fuel tank and let the engine run

until all fuel is out of the carburetor.

2. Disconnect and remove the spark plug wire away from

the spark plug before any other preparations are made!

3. Tape all openings closed to prevent spraying water into

the exhaust or air intakes during washing.

4. Tilt the mower up on its rear wheels and thoroughly

clean the underside of the deck. Do not tilt the mower

with the spark plug or carburetor down. Scrape away

any accumulation of grass with a putty knife and/or

wire brush.

5. Lubricate all exposed metal with a light coating of oil to

prevent corrosion.

6. Carefully fold the handles, “flexing” the control cables to

prevent cable damage.

7. Store the mower in a shed or other dry area, protected

from weather.

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

Wear heavy leather gloves when handling or working

around cutting blades. Blades are extremely sharp and can

cause severe injury.

!!

Not for

Reproduction

www.snapper.com14

Maintenance

Mower Blade Replacement

Standard Blade Wear Limit

1. Inspect the blade (Figure 15) frequently for signs of

excessive wear or damage:

(A) New blade

(B) Wear limit (notch starts)

(C) Dangerous condition! Do not use on the mower!

Replace with a new blade.

Blade Sharpening

1. Disconnect the spark plug wire and secure the end away

from the plug.

2. Tilt the mower up on its rear wheels. Do not tilt the

mower with the spark plug or carburetor down.

Important: Drain the fuel tank before tipping the mower. DO

NOT tip the machine with the carburetor or spark plug down.

Oil from the crankcase will saturate the air filter and cause

the engine to be hard to start or not start at all. If

contamination does occur, the air filter will have to be

replaced.

3. Remove the blade (B, Figure 16).

4. Sharpen the blade on a grinding wheel at an angle of 22

to 28 degrees (B, Figure 17). DO NOT sharpen the blade

beyond the original cutting edge (A).

5. Check blade for balance. If necessary, correct balance by

grinding heavy end of blade.

6. Reinstall blade (B, Figure 16). Note the correct

assembly order:

(A) Blade hub

(B) Blade

(C) Blade flange (facing up)

(D) Cone washer (concave side up)

(E) Capscrew

7. Check torque of blade retaining cap screw.

Recommended torque should be 40 ft. lbs.

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

Wear heavy leather gloves when handling or working

around cutting blades. Blades are extremely sharp and can

cause severe injury.

!!

Figure 15: Mower blade wear limits

A

B

C

WARNING

DO NOT use a cutting blade that shows signs of excessive

wear or damage. Refer to the Section entitled “MOWER

BLADE REPLACEMENT” for proper blade inspection and

service procedures.

!!

Make sure that

blade hub is seated

between flanges

Figure 16: Removing the mower blade

Do not sharpen

beyond original

cutting edge

End view of

blade assembly

22-280

Figure 17: Sharpening the mower blade

A

B

C

A

B

D

E

Not for

Reproduction

15

Maintenance

Wheel Drive Control Adjustment

The wheel drive control lever (A, Figure 18) should engage

the transmission when the lever is squeezed back toward the

handlebar, and should disengage the transmission when the

lever is released.

If the transmission does not engage or disengage, contact

your authorized Snapper dealer for service before operating

the mower.

WARNING

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

Disconnect spark plug wire and secure away from spark

plug. Engine and components are HOT. Avoid serious

burns, allow sufficient time for all components to cool.

! !

Figure 18: Wheel drive controls

A

(Components removed for clarity)

Not for

Reproduction

www.snapper.com16

Maintenance

ITEMSERVICE

PERFORMED

REF. EACH

USE

5

HRS

25

HRS

50

HRS

100

HRS

EACH

SEASON

Engine Oil Check Oil Level Page 8 X

Initial Oil Change Page 12 X

Periodic Oil Change Page 12 X*

Air Pre-Cleaner Clean Sponge Element Engine Manual X**

Air Cleaner Clean or Replace Engine Manual X**

Spark Plug Replace Engine Manual X

Engine Cooling

System

Clean Shroud & Fins Engine Manual X**

Drive Belt Check for Wear and

Tension

Page 12 X

Mower Blade Check for wear, Damage

& Replacement

Page 12, 14 X

Mower Deck Clean Debris

Accumulation

Page 8 X

Wheel Drive

Components

Clean Debris

Accumulation; Check for

Wear or Damage

Page 13 X

Transmission Cable

Spring Adjustment

Check & Adjust Page 15 X X X

Service Schedule

Not for

Reproduction

17

Troubleshooting

PROBLEM PROBABLE CAUSE CORRECTIVE ACTION

Engine Will Not Start

Using Recoil Starter

1. Fuel tank empty. 1. Fill fuel tank with fresh fuel.

2. Engine needs priming. 2. Prime. Check Engine Manual for Instructions.

3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug.

Engine Will Not Start

(Electric Start Models)

1. Fuel tank empty. 1. Fill fuel tank with fresh fuel.

2. Engine needs priming. 2. Prime. Check Engine Manual for Instructions.

3. Spark plug wire disconnected. 3. Place spark plug wire onto spark plug.

4. Wiring harness disconnected. 4. Connect wiring harness.

5. Battery dead. 5. Charge or replace battery.

Engine Stalls or Stops

After Running

1. Blade control is released or is not being held

securely against handle.

1. Blade control should be held securely against

handle at all times during operation of mower.

2. Fuel tank empty. 2. Fill with fuel to proper level.

3. Engine air pre-cleaner and or air cleaner dirty. 3. Clean free of all debris.

4. Spark plug defective or gap set improperly. 4. Service spark plug.

5. Water, debris or stale fuel in fuel system. 5. Drain and clean fuel system.

Engine Loses Power 1. Engine air pre-cleaner or air cleaner dirty. 1. Clean or replace filters.

2. Spark plug faulty. 2. Service spark plug.

3. Water, debris or stale fuel in fuel system. 3. Drain and clean fuel system.

Excessive Vibration 1. Damaged, out of balance or bent mower blade. 1. Service mower blade.

2. Loose blade components. 2. Service and tighten loose parts.

3. Loose or missing air lift (if equipped). 3. Replace air lifts. Tighten to proper torque.

4. Lumpy or frayed belt. 4. Replace belt.

Mower Will Not Move

Loss Of Traction

1. Build-up of debris on or around wheel drive

components.

1. Clean debris.

2. Transmission cable adjustment required. 2. Contact authorized SNAPPER dealer.

3. Drive belt requires replacement. 3. Contact authorized SNAPPER dealer.

4. Damaged transmission. 4. Contact authorized SNAPPER dealer.

Transmission Noise 1. Transmission cable adjustment required. 1. Contact authorized SNAPPER dealer.

2. Damaged transmission. 2. Contact authorized SNAPPER dealer.

Ground Speed

Too Fast / Too Slow;

Unable to Adjust

Ground Speed

1. Build-up of debris on or around wheel drive

control components.

1. Clean debris.

2. Transmission cable adjustment required. 2. Contact authorized SNAPPER dealer.

3. Drive belt requires replacement. 3. Contact authorized SNAPPER dealer.

4. Damaged transmission. 4. Contact authorized SNAPPER dealer.

Cutting Grass Improperly1. Cutting height too low or high. 1. Adjust cutting height.

2. Forward speed too fast. 2. Adjust to a slower speed.

3. Cutting blade dull or damaged. 3. Sharpen cutting edges or replace blade.

Poor Grass Discharge 1. Forward speed too fast. 1. Adjust to a slower speed.

2. Grass is wet. 2. Mow when grass is dry.

3. Excessively worn or damaged blade. 3. Service mower blade.

4. Build up of grass clippings and debris under

deck.

4. Clean deck.

5. Improper blade installed on deck. 5. Install proper SNAPPER blade.

6. Blade installed improperly on deck. 6. Install blade properly.

Oil Leaking 1. Leaking engine case. 1. Contact authorized SNAPPER dealer.

2. Check and tighten drain plug.

3. Make sure dip stick or oil filler cap is securely in

place.

Troubleshooting

Not for

Reproduction

www.snapper.com18

Warranties

BRIGGS & STRATTON POWER PRODUCTS GROUP, L.L.C. OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair and/or replace, free of charge, any part(s) of the equipment that is

defective in material or workmanship or both. Briggs & Stratton Corporation will repair and/or replace, free of charge, any

part(s) of the Briggs and Stratton engine* (if equipped) that is defective in material or workmanship or both. Transportation

charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is

effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized

Service Dealer using our dealer locator at www.BriggsandStratton.com or www.Snapper.com.

There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular

purpose, are limited to one year from purchase or to the extent permitted by law. Liability for incidental or consequential

damages are excluded to the extent exclusion is permitted by law.

Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do

not allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not

apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state

or country to country.

WARRANTY PERIOD

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the

period of time stated above. “Consumer use” means personal residential household use by a retail consumer. “Commercial

use” means all other uses, including use for commercial, income producing or rental purposes. Once product has experienced

commercial use, it shall thereafter be considered as commercial use for purposes of this warranty.

No warranty registration is necessary to obtain warranty on Briggs & Stratton products. Save your proof of purchase receipt. If you

do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the product will

be used to determine warranty eligibility.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Warranty service is available only through servicing

dealers authorized by Briggs & Stratton or BSPPG, LLC.

Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. This warranty

only covers defects in materials or workmanship. It does not cover damage caused by improper use or abuse, improper

maintenance or repair, normal wear and tear, or stale or unapproved fuel.

Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in

a way not described in the Operator’s Manual or using the product after it has been damaged will void your warranty. Warranty is

not allowed if the serial number on the product has been removed or the product has been altered or modified in any way, or if the

product has evidence of abuse such as impact damage, or water/chemical corrosion damage.

Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the

Operator’s Manual, and serviced or repaired using genuine Briggs & Stratton parts. Damage caused by lack of maintenance or use

of non-original parts is not covered by warranty.

Normal Wear - Like all mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not

cover repairs when normal use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters,

belts, cutting blades, and brake pads (engine brake pads are covered) are not covered by warranty due to wear characteristics

alone, unless the cause is due to defects in material or workmanship.

Stale Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s

Manual. Damage caused by stale fuel (carburetor leaks, clogged fuel tubes, sticking valves, etc) is not covered by warranty.

* Applies to Briggs and Stratton engines only. Warranty coverage of non-Briggs and Stratton engines is provided by the engine manufacturer.

Item Consumer Use Commercial Use:

Equipment 2 Years 90 Days

Engine* 2 Years 90 Days

Battery 1 Year 1 Year

Not for

Reproduction

19

Not for

Reproduction

www.snapper.com

Snapper Products

535 Macon Street

McDonough, GA 30253

WALK BEHIND MOWER

EUROPEAN MODEL

ESPV21675

1-800-935-2967

Engine Power Rating Information: The gross power rating for individual gas engine models is labeled in accordance with SAE

(Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has

been obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060 RPM;

horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among other things,

ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are

placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the

rated gross power when used in a given piece of power equipment (actual "on-site" or net horsepower). This difference is due

to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump,

etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability.

Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this

Series engine.

20

Common Service Parts Part Number

Blade Control Cable 7101399

Wheel Drive Control Cable 7101398

Cutter Blade (Double Wave) 7100242

Drive Belt 7100883

Parts Manual 7006259

Product Specifications

Deck Size (in) 21

Height of Cut (in) 1.25 - 4

Transmission Type Variable Speed/Gear

Ground Speed (mph) 0 - 4

Engine Power (ft-lbs) 6.75

Engine Displacement (cc) 190

Fuel Tank Capacity (qt) 1.0

Not for

Reproduction

La page est en cours de chargement...

Simplicity MANUAL, OPS, ESPV21675 Manuel utilisateur

Simplicity MANUAL, OPS, ESPV21675 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents