Samsung HT-H6500WM Manuel utilisateur

Catégorie
Lecteurs Blu-Ray
Taper
Manuel utilisateur
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
5.1CH Blu-ray™
Home Entertainment System
user manual
HT-H6500WM
HT-H6530WM
HT-H6500WM_30WM_ZC-0514.indd 1HT-H6500WM_30WM_ZC-0514.indd 1 2014-05-15  11:52:292014-05-15  11:52:29
2 - English
Safety Information
The slots and openings in the cabinet and in the back
or bottom are provided for necessary ventilation. To
ensure reliable operation of this apparatus, and to
protect it from overheating, these slots and openings
must never be blocked or covered.
- Do not place this apparatus in a confined space,
such as a bookcase, or built-in cabinet, unless
proper ventilation is provided.
- Do not place this apparatus near or over a radiator
or heat register, or where it is exposed to direct
sunlight.
- Do not place vessels (vases etc.) containing water
on this apparatus. A water spill can cause a fire or
electric shock.
Do not expose this apparatus to rain or place it near
water (near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming
pool, etc.). If this apparatus accidentally gets wet,
unplug it and contact an authorized dealer immediately.
This apparatus uses batteries. In your community,
there might be environmental regulations that require
you to dispose of these batteries properly. Please
contact your local authorities for disposal or recycling
information.
Do not overload wall outlets, extension cords or
adaptors beyond their capacity, since this can result in
fire or electric shock.
Route power-supply cords so that they are not likely to
be walked on or pinched by items placed on or against
them. Pay particular attention to cords at the plug end,
at wall outlets, and the point where they exit from the
apparatus.
To protect this apparatus from a lightning storm, or
when it is left unattended and unused for long periods
of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage
to the set due to lightning and power line surges.
Before connecting the AC power cord to the DC
adaptor outlet, make sure the voltage designation of
the DC adaptor corresponds to the local electrical
supply.
Never insert anything metallic into the open parts
of this apparatus. Doing so may create a danger of
electric shock.
To avoid electric shock, never touch the inside of this
apparatus. Only a qualified technician should open this
apparatus.
Make sure to plug the power cord in until it is firmly
seated. When unplugging the power cord from a wall
outlet, always pull on the power cord's plug. Never
unplug by pulling on the power cord. Do not touch the
power cord with wet hands.
If this apparatus does not operate normally - in
particular, if there are any unusual sounds or smells
coming from it - unplug it immediately and contact an
authorized dealer or service center.
Maintenance of Cabinet.
- Before connecting other components to this
product, be sure to turn them off.
- If you move your product suddenly from a cold place
to a warm place, condensation may occur on the
operating parts and lens and cause abnormal disc
playback. If this occurs, unplug the product, wait for
two hours, and then connect the plug to the power
outlet. Then, insert the disc, and try to play back
again.
Be sure to pull the power plug out of the outlet if the
product is to remain unused or if you are leaving the
house for an extended period of time (especially when
children, elderly, or disabled people will be left alone in
the house).
- Accumulated dust can cause an electric shock, an
electric leakage, or a fire by causing the power cord
to generate sparks and heat or the insulation to
deteriorate.
Contact an authorized service center for information
if you intend to install your product in a location with
heavy dust, high or low temperatures, high humidity,
chemical substances, or where it will operate 24 hours
a day such as in an airport, a train station, etc. Failing
to do so may lead to serious damage of your product.
Use only a properly grounded plug and wall outlet.
- An improper ground may cause electric shock or
equipment damage. (Class l Equipment only.)
To turn this apparatus off completely, you must
disconnect it from the wall outlet. Consequently, the
wall outlet and power plug must be readily accessible
at all times.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE THE COVER (OR BACK). THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO
QUALIFIED PERSONNEL.
This symbol indicates that high voltage is
present inside. It is dangerous to make
any kind of contact with any internal part
of this product.
This symbol indicates that important
literature concerning operation and
maintenance has been included with this
product.
HT-H6500WM_30WM_ZC-0514.indd 2HT-H6500WM_30WM_ZC-0514.indd 2 2014-05-15  11:52:332014-05-15  11:52:33
3 - English
Safety Information
Do not allow children to hang on the product.
Store the accessories (battery, etc.) in a location safely
out of the reach of children.
Do not install the product in an unstable location such
as a shaky self, a slanted floor, or a location exposed
to vibration.
Do not drop or strike the product. If the product is
damaged, disconnect the power cord and contact a
service center.
To clean this apparatus, unplug the power cord from
the wall outlet and wipe the product using a soft,
dry cloth. Do not use any chemicals such as wax,
benzene, alcohol, thinners, insecticide, air fresheners,
lubricants, or detergent. These chemicals can damage
the appearance of the product or erase the printing on
the product.
Do not expose this apparatus to dripping or splashing.
Do not put objects filled with liquids, such as vases on
the apparatus.
Do not dispose of batteries in a fire.
Do not plug multiple electric devices into the same wall
socket. Overloading a socket can cause it to overheat,
resulting in a fire.
There is danger of an explosion if you replace the
batteries used in the remote with the wrong type of
battery. Replace only with the same or equivalent type.
WARNING :
TO PREVENT THE SPREAD OF FIRE,
KEEP CANDLES AND OTHER ITEMS
WITH OPEN FLAMES AWAY FROM THIS
PRODUCT AT ALL TIMES.
NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Section 820~40 of the NEC which
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.
CLASS 1 LASER PRODUCT
This product is classified as a CLASS 1 LASER product.
Use of controls, adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
DANGER :
VISIBLE AND INVISIBLE LASER RADIATION WHEN
OPEN. AVOID DIRECT EXPOSURE TO BEAM.
(FDA 21 CFR)
CAUTION :
CLASS 3B VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. AVOID EXPOSURE TO THE
BEAM (IEC 60825-1)
THIS PRODUCT UTILIZES A LASER. USE OF
CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN THE COVER. DO
NOT REPAIR THE PRODUCT YOURSELF. REFER
SERVICING TO QUALIFIED PERSONNEL.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LÁSER CLASE 1
Important Safety Instructions
Read these operating instructions carefully before using
the unit. Follow all the safety instructions listed below.
Keep these operating instructions handy for future
reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including AV receivers) that produce heat.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where it exits the
apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
HT-H6500WM_30WM_ZC-0514.indd 3HT-H6500WM_30WM_ZC-0514.indd 3 2014-05-15  11:52:332014-05-15  11:52:33
4 - English
Safety Information
12. Use only with the cart, stand,
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use
caution when moving the cart/
apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as when the power-
supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
3D Precautions
IMPORTANT HEALTH AND SAFETY INFORMATION FOR
3D PICTURES.
Read and understand the following safety information
before using the 3D function.
Some viewers may experience discomfort while viewing
3D TV such as dizziness, nausea, and headaches.
If you experience any such symptom, stop viewing 3D
TV, remove the 3D Active Glasses, and rest.
Watching 3D images for an extended period of time
may cause eye strain. If you feel eye strain, stop
viewing 3D TV, remove your 3D Active Glasses, and
rest.
A responsible adult should frequently check on children
who are using the 3D function.
If there are any reports of tired eyes, headaches,
dizziness, or nausea, have the child stop viewing 3D
TV and rest.
Do not use the 3D Active Glasses for other purposes
(such as general eyeglasses, sunglasses, protective
goggles, etc.)
Do not use the 3D function or 3D Active Glasses while
walking or moving around. Using the 3D function or 3D
Active Glasses while moving around may cause you to
bump into objects, trip, and/or fall, and cause serious
injury.
If you want to enjoy 3D content, connect a 3D device
(3D compliant AV receiver or TV) to the product’s HDMI
OUT port using a high-speed HDMI cable. Put on 3D
glasses before playing the 3D content.
The product outputs 3D signals only through an HDMI
cable connected to the HDMI OUT port.
The video resolution in 3D play mode is fixed to the
resolution of the original 3D video. You can not change
the resolution.
Some functions such as BD Wise, screen size
adjustment, and resolution adjustment may not operate
properly in 3D play mode.
You must use a high-speed HDMI cable for proper
output of the 3D signal.
Stay at least three times the width of the screen from
the TV when watching 3D images. For example, if you
have a 46 inch screen, stay 138 inches (11.5 feet) from
the screen.
Place the 3D video screen at eye level for the best 3D
picture.
When the product is connected to some 3D devices,
the 3D effect may not function properly.
This product does not convert 2D content into 3D.
“Blu-ray 3D” and “Blu-ray 3D” logo are trademarks of
the Blu-ray Disc Association.
HT-H6500WM_30WM_ZC-0514.indd 4HT-H6500WM_30WM_ZC-0514.indd 4 2014-05-15  11:52:342014-05-15  11:52:34
5 - English
Contents
Contents
GETTING STARTED
6 Accessories
6 Speaker Components
7 Front Panel
7 Rear Panel
8 Remote Control
CONNECTIONS
9 Connecting the Speakers
11 Attaching the Toroidal Ferrite Core to the Power
Cord of the Wireless Receiver Module (SWA-
6000)
12 Connecting to a TV and External Devices
13 Connecting to a Network Router
SETTINGS
14 The Initial Settings Procedure
14 The Home Screen at a Glance
15 Accessing the Settings Screen
15 Settings Menu Functions
20 Network Setup
23 Wi-Fi Direct
24 Upgrading Software
PLAYING CONTENT
26 Playing Commercial Discs
26 Playing Multimedia Files
28 Controlling Video Playback
31 Controlling Music Playback
36 Using Bluetooth
38 Playing Photo Contents
39 Listening to the Radio
40 Using the Special Effects Remote Control
Buttons
NETWORK SERVICES
41 Logging In to Your Samsung Account
41 Adding a Credit Card
41 Before Using MOVIES & TV SHOWS or
SAMSUNG APPS
42 Using MOVIES & TV SHOWS
43 Using SAMSUNG APPS
45 Screen Mirroring
45 Using the Web Browser
48 Linking your Internet Service Accounts to the
Product
48 BD-LIVE™
APPENDIX
49 Additional Information
50 Disk and Format Compatibility
57 Troubleshooting
60 Specifications
62 Licenses
Figures and illustrations in this User Manual
are provided for reference only and may differ
from actual product appearance.
An administration fee may be charged if either
a. an engineer is called out at your request
and there is no defect in the product (i.e.
where you have failed to read this user
manual)
b. you bring the unit to a repair center and
there is no defect in the product (i.e. where
you have failed to read this user manual).
The amount of such administration charge will
be advised to you before any work or home
visit is carried out.
HT-H6500WM_30WM_ZC-0514.indd 5HT-H6500WM_30WM_ZC-0514.indd 5 2014-05-15  11:52:342014-05-15  11:52:34
6 - English
Getting Started
Check the box for the accessories and speaker components listed or shown below.
Accessories
Remote Control Lithium Battery User Manual
(For Power cord)
Power Cable FM Antenna
Toroidal Ferrite Core
Soft Cloth
WARNING, DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD,
[The remote control supplied with] This product contains a coin/button cell battery.
If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death. Keep new and used batteries away from children. If the battery compartment does not
close securely, stop using the product and keep it away from children. If you think batteries might have been
swallowed or placed inside any part of the body, seek immediate medical attention.
Speaker Components
HT-H6500WM
Center
Front x 2 Surround x 2
Speaker Cable
x 6 Subwoofer
Wireless Receiver
Module (SWA-6000)
HT-H6530WM
Speaker Cable
x 4
Screw (5x20) x 8
Stand Base x 2 Center
Front x 2 Stand x 2 Surround x 2 Subwoofer
Wireless Receiver
Module (SWA-6000)
HT-H6500WM_30WM_ZC-0514.indd 6HT-H6500WM_30WM_ZC-0514.indd 6 2014-05-15  11:52:352014-05-15  11:52:35
7 - English
Getting Started
Front Panel
DISPLAY ICONS
FUNCTION STOP PLAY/PAUSE
OPEN/
CLOSE
VOLUME
CONTROL
POWER
5V 0.5A
USBREMOTE CONTROL SENSOR
DISPLAY
DISC TRAY
When the product is on, do not let children touch the product's surface. It will be hot.
To upgrade the product's software through the USB jack, you must use a USB flash drive.
When the product displays a Blu-ray Disc menu, you cannot start the movie by pressing the /
p
button
on the product or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and
then press the
OK
button.
If you are using the Internet or are playing content from a USB device on your TV through the home theater,
you cannot select the BD/DVD mode with the
SOURCE button. To select the BD/DVD mode, exit the
Internet or stop the content you are playing on the TV, and then select the BD/DVD mode.
Rear Panel
HDMI OUT
LAN
POWER
AUX IN FM ANT
OPTICAL
DIGITAL
AUDIO IN
L
R
HDMI IN
SPEAKERS OUT
CENTER
SUBWOOFER
FRONT
L
FRONT
R
IMPEDANCE : 3
COOLING FAN
* FM ANTENNAAUX IN
HDMI OUT
SPEAKER OUTPUT
CONNECTORS
POWER CORD
LAN TERMINAL
HDMI INEXTERNAL DIGITAL
AUDIO IN (OPTICAL)
* Connecting the FM Antenna
1. Connect the supplied FM antenna to the FM ANT Jack.
2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a
wall or other rigid surface.
Maintain a minimum of 4 inches of clear space on all sides of the home theater to ensure adequate
ventilation.
Do not obstruct the cooling fan or ventilation holes.
This product does not receive AM broadcasts.
HT-H6500WM_30WM_ZC-0514.indd 7HT-H6500WM_30WM_ZC-0514.indd 7 2014-05-15  11:52:392014-05-15  11:52:39
8 - English
Getting Started
Remote Control
Tour of the Remote Control
Installing batteries in the Remote Control
1
Use a coin to turn the remote
control cover anti-clockwise to
remove it as shown in the figure
above.
2
Insert a 3V lithium battery. Keep
the positive (+) pole upward
when inserting the battery. Put
the battery cover on and align
the '●' marks side by side as
shown in the figure above.
3
Use a coin to turn the cover
clockwise as far as it will go to
fix it in place.
Turn the product on and off.
Adjust the volume.
Press to move to the Home screen.
Press to skip backwards(
[
) or
forwards(
]
)
or
Press and hold to search
backwards(
(
) or forwards(
)
).
Select on-screen menu items and
change menu values.
,.
:
Search for active FM stations
and to change channels.
Return to the previous menu.
Use to enter the Popup menu/Title
menu.
Press to apply sound effects.
Press to apply the DTS Neo:Fusion II
or 3D sound effect.
These buttons are used both for
menus on the product and also several
Blu-ray Disc functions.
Press to select MANUAL/PRESET in
the Tuner function.
Cut off the sound temporarily.
Press to play disc or files.
or
Press to pause playing.
Press to select the Home Theater's
mode (HDMI, AUX, BD/DVD, etc.).
Press to use the Tools menu.
or
To display the number keypad (may
include function keys when applicable)
on the screen, press and hold the
button.
Press to stop the disc playing or to exist
the menu.
Use to display the playback information
when playing a Blu-ray/DVD disc or files.
Use to set a preset radio frequency.
Press to view the disc menu.
Set a Sleep time to shut off the product.
Press to open and close the disc tray.
Select STEREO or MONO for radio
broadcasts.
While playing multimedia content in SAMSUNG APPS, press and hold
5
button on the remote to pause
playback. To stop playback, press and hold
e
(
EXIT) button on the remote.
HT-H6500WM_30WM_ZC-0514.indd 8HT-H6500WM_30WM_ZC-0514.indd 8 2014-05-15  11:52:402014-05-15  11:52:40
9 - English
Connections
This section describes various methods of connecting the product to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Connecting the Speakers
Surround (L)
Surround (R)
Product
Center
Subwoofer
Wireless
Receiver Module
Front (L)
Front (R)
Position of the product
Place it on a stand or cabinet shelf, or
under the TV stand.
Selecting the Listening Position
The listening position should be
located about 2.5 to 3 times the TV's
screen size away from the TV. For
example, if you have a 46 inch screen,
locate the listening position 115 to
138 inches (9.6 to 11.5 feet) from the
screen.
Front Speakers
Place these speakers in front of your listening position, facing inwards (about
45°) toward you. Place the front speakers so that their tweeters will be at the
same height as your ear. Align the front face of the front speakers with the front
face of the center speaker or place them slightly in front of the center speakers.
Center Speaker
It is best to install the Center Speaker at the same height as the front speakers.
You can also install it directly over or under the TV.
Surround Speakers
Place these speakers to the side of your listening position. If there isn't enough
room, place these speakers so they face each other. Position them about 2 to 3
feet (60 to 90cm) above your ear, facing slightly downward.
* Unlike the front and center speakers, the surround speakers are used mainly
for sound effects. Sound will not come from them all the time.
Subwoofer
The position of the subwoofer is not so critical. Place it anywhere you like.
* Surround speakers must be connected to the wireless receiver module.
* The appearance of your speakers may differ from the illustrations in this manual.
* Each speaker has a colored label on its back or underside. Each cable has a single colored band near
its end. Match the band on each cable to the speaker label by color, and then connect the cable to the
speaker. See page 10 for exact instructions.
Connections
HT-H6500WM_30WM_ZC-0514.indd 9HT-H6500WM_30WM_ZC-0514.indd 9 2014-05-15  11:52:412014-05-15  11:52:41
10 - English
Connections
Installing the Speakers on the Tallboy Stands
* HT-H6530WM only - Front Speakers
1. Find the speaker cable that is attached to the Stand. Turn
the Stand and Stand Base upside-down, unravel the
speaker cable, and then draw it through the hole in the
Stand Base.
Handle the Stand carefully. It is heavy.
2. Connect the Stand Base to the bottom of the Stand.
3. Insert three 5x20 screws into the marked holes in the
Stand Base, and then tighten them with a screwdriver as
shown in the illustration.
4. Place the speaker cable into the slot on the bottom of the
stand base.
5. Connect the assembled stand and a speaker together by
matching the labels on the stand and speaker with each
other as shown in the picture.
6. Insert a screw (5x20) into the hole on the rear of the
speaker and tighten by turning it clockwise with a
screwdriver.
7. Repeat steps 1 through 6 with the other speaker and
stand.
Speaker Cable Connections
1. Match each speaker cable bundle to the correct speaker by matching the color coded plug on each bundle
to the colored sticker on the bottom or back of each speaker.
2. Connect the speaker wire plugs from each speaker to the back of the product by matching the colors of
the speaker plugs to the colors of the speaker jacks.
In case of HT-H6500WM
HDM
AUX IN FM ANT
OPTICAL
DIGITAL
AUDIO IN
L
R
SPEAKERS OUT
CENTER
SUBWOOFER
FRONT
L
FRONT
R
IMPEDANCE : 3
SPEAKERS OUT
CENTER
SUBWOOFER
FRONT
L
FRONT
R
IMPEDANCE : 3
Front Speaker (R)
Subwoofer
Center Speaker
Wireless Receiver Module
Surround
Speaker (L)
Front Speaker (L)
Surround
Speaker (R)
* Refer to page 6 for the speakers of HT-H6530WM.
* This product should be connected with the SWA-6000 only.
1
3
5 6
4
Speaker
Stand
Stand Base
Stand
2
HT-H6500WM_30WM_ZC-0514.indd 10HT-H6500WM_30WM_ZC-0514.indd 10 2014-05-15  11:52:422014-05-15  11:52:42
11 - English
Connections
If you place a speaker near your TV set, the screen color may be distorted because of the magnetic field.
Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too
close to the product, sound from the speakers may be disrupted because of interference.
If you use a device such as a microwave oven, wireless LAN Card, Bluetooth device, or any other device
that uses the 2.4/5.8GHz frequencies near the product, sound from the speakers may be disrupted because
of interference.
The maximum transmission distance from the product to the wireless receiver module is about 33 feet (10m),
but may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between
the product and the wireless receiver module, the system may not operate at all, because the radio waves
cannot penetrate metal.
If the product doesn't make a wireless connection, you need to run an ID Set between the product and
wireless receiver module. With the product turned off, press and hold
(mute) button on the remote control
for 5 seconds. Turn on the wireless receiver module. Then, press and hold the "ID SET" button on the back
of the wireless receiver module for 5 seconds, and then turn the product on.
| CAUTION |
If you want to install the speakers on the wall, fasten screws or nails (not provided) firmly to the wall wherever
you want to hang a speaker, and then, using the hole in the rear of each speaker, carefully hang each
speaker on a screw or nail.
Do not let children play with or near the speakers. They could get hurt if a speaker falls.
When connecting the speaker wires to the speakers, make sure that the polarity (+/ –) is correct.
Keep the subwoofer speaker out of reach of children to prevent children from inserting their hands or alien
substances into the duct (hole) of the subwoofer speaker.
Do not hang the subwoofer on the wall using the duct (hole).
The wireless receiving antenna is built into the wireless receiver module. Keep it away from water and
moisture.
For optimal listening performance, make sure that the area around the wireless receiver module location is
clear of any obstructions.
In 2-CH mode, you will hear no sound from the wireless surround speakers.
Attaching the Toroidal Ferrite Core to the Power Cord of the Wireless
Receiver Module (SWA-6000)
If you attach a Toroidal ferrite core to the power cord of the wireless
receiver module, it will help prevent RF interference from radio signals.
1. Pull the fixing tab of the Toroidal ferrite core to open it.
2. Make two loops in the wireless receiver module power cord.
3. Attach the Toroidal ferrite core to the wireless receiver module's
power cord as shown in the figure on the right, and then close it
by pressing it until it clicks.
Attach the ferrite core as close to the Wireless Receiver Module
as possible.
HT-H6500WM_30WM_ZC-0514.indd 11HT-H6500WM_30WM_ZC-0514.indd 11 2014-05-15  11:52:452014-05-15  11:52:45
12 - English
Connections
Connecting to a TV and External Devices
HDMI OUT
LAN
AUX IN FM ANT
OPTICAL
DIGITAL
AUDIO IN
L
R
HDMI IN
HDMI OUT HDMI IN
AUDIO OUT
OPTICAL OUT
HDMI OUT
LAN
POWER
AUX IN FM ANT
OPTICAL
DIGITAL
AUDIO IN
L
R
HDMI IN
SPEAKERS OUT
CENTER
SUBWOOFER
FRONT
L
FRONT
R
IMPEDANCE : 3
Method 1 Method 2 Method 3
R
Red
W
White
External Devices
Connecting to a TV
Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI IN jack
on your TV. If the TV supports ARC, you can hear the audio from your TV through the home theater with only
this cable connected. See page 17 in this manual and the section on ARC in your TV's user's manual for details.
Connecting to External Devices
Method 1 AUX IN : Connecting an External Analog Component
Using an RCA audio cable (not supplied), connect the AUDIO In jack on the product to the AUDIO Out jack on
the external analog component.
Select the AUX mode.
Be sure to match the colors on the cable plugs to the colors on the input and output jacks.
Method 2 OPTICAL : Connecting an External Digital Audio Component
Use to connect the digital audio output of digital signal components such as Cable Boxes and Satellite
Receivers (Set-Top-Boxes) to the home theater. Using a digital optical cable (not supplied), connect the Optical
Digital Audio In jack on the product to the Digital Optical Out jack of the external digital device using a digital
optical cable.
Select the D. IN mode.
Method 3 HDMI IN : Connecting to an External Component with an HDMI Cable
Connect an HDMI cable (not supplied) from the HDMI IN jack on the back of the product to the HDMI OUT jack
on your digital device.
Select the HDMI mode.
To see video from your Cable Box/Satellite receiver, you must connect its video output directly to your TV.
This system supports Digital sampling frequencies of 32 kHz or higher from external digital components.
This system supports only DTS and Dolby Digital audio. MPEG audio, a bitstream format, is not supported.
Selecting an External Device to Use
To select an external device after you have connected it, press the SOURCE button. Each time you press the
button, the mode changes in this order :
BD/DVD
D. IN
AUX
HDMI
FM
BT
HT-H6500WM_30WM_ZC-0514.indd 12HT-H6500WM_30WM_ZC-0514.indd 12 2014-05-15  11:52:452014-05-15  11:52:45
13 - English
Connections
Connecting to a Network Router
You can connect your product to your network router
using one of the methods illustrated below.
Wired Network
Broadband
service
Broadband
service
Broadband modem
(with integrated router)
Broadband
modem
Router
Or
HDMI OUT
LAN
POWER
AUX IN FM ANT
OPTICAL
DIGITAL
AUDIO IN
L
R
HDMI IN
SPEAKERS OUT
CENTER
SUBWOOFER
FRONT
L
FRONT
R
IMPEDANCE : 3
Your router or your Internet Service Provider's
policies may prevent the product from accessing
Samsung's software update server. If this occurs,
contact your Internet Service Provider (ISP) for
more information.
DSL users, please use a router to make a network
connection.
To use the DLNA function, you must connect your
PC to your network as shown in the illustrations
above.
The connection can be wired or wireless.
Wireless Network
Broadband
service
Wireless IP sharer
If your wireless IP router supports DHCP, this
product can use a DHCP or static IP address to
connect to the wireless network.
Set your wireless IP router to Infrastructure mode.
Ad-hoc mode is not supported.
The product supports only the following wireless
security key protocols:
- WEP (OPEN/SHARED), WPA-PSK (TKIP/AES),
WPA2-PSK (TKIP/AES)
Select a channel on the wireless IP router that is
not currently being used. If the channel set for
the wireless IP router is currently being used by
another device nearby, it will result in interference
and communication failure.
In compliance with the newest Wi-Fi certification
specifications, Samsung home theaters do not
support WEP, TKIP, or TKIP-AES (WPS2 Mixed)
security encryption in networks running in the
802.11n mode.
Wireless LAN, by its nature, may cause
interference, depending on the operating
conditions (AP performance, distance, obstacles,
interference by other radio devices, etc).
HT-H6500WM_30WM_ZC-0514.indd 13HT-H6500WM_30WM_ZC-0514.indd 13 2014-05-15  11:52:462014-05-15  11:52:46
14 - English
Settings
The Initial Settings Procedure
The Home menu will not appear if you do not
configure the initial settings.
The OSD (On Screen Display) may change in
this product after you upgrade the software
version.
The access steps may differ depending on the
menu you selected.
After you have finished connecting the home theater
to your TV, turn on the TV, and then turn on the
home theater. The first initial setup screen appears.
The setup screens appear in this order: Language,
Network Configuration, Terms and Conditions, Screen
Resolution (Aspect Ratio), and Speaker Layout.
Depending on the software version installed on your
home theater, you may also see the Software Update
screen. Follow the instructions displayed on each
screen, which will guide you through the easy setup
procedure.
If you are not ready to set up the network
configuration or it is problematic, you can select Skip
and set it up later.
(See page 20)
To edit your settings after the initial setup, select
Settings > System > Setup in the Home screen
or select the Reset option. (See page 20)
The Home Screen at a Glance
PLAY DISC
App 1 App 2 App 3 App 4 App 5 App 6
Screen Mirroring
Function Settings
MOVIES & TV SHOWS
MULTIMEDIA
SAMSUNG APPS
No Disc
1234
56 897
RECOMMENDED MY APPS
1
PLAY DISC
Displays information about the disc currently in the
disc tray. Press OK to start playing the disc.
2
MOVIES & TV SHOWS
Download movies and TV Shows from the Internet.
Depending on your country, this menu function
may not be supported.
3
MULTIMEDIA
Play photos, videos, or music content from
Discs, USB devices, PCs, mobile devices, or
cloud services.
4
SAMSUNG APPS
Download/Access various for pay or free-of-
charge applications.
5
RECOMMENDED
A list of useful and popular apps we recommend
you download.
6
MY APPS
Displays downloaded and installed apps. You
can change the display order. (See page 42)
7
Screen Mirroring
Set up the wireless mirroring function between
the home theater and a smart phone or tablet.
Depending on your country, this menu function
may not be supported.
8
Function
Use to switch between external devices connected
to Digital In, AUX, or HDMI IN, to switch to the
Tuner, or to switch to a connected Bluetooth
device. You can also use the remote's SOURCE
button or the main unit's button.
9
Settings
Set various functions to suit your personal preferences.
Selecting an Option on the Home Screen
1. To select an option on the Home screen, move
the cursor using the
,.
buttons until it
highlights the option of your choice, and then
press the OK button.
If you leave the product in the stop mode for more
than 5 minutes without using it, a screen saver
will appear on your TV. If the product is left in the
screen saver mode for more than 20 minutes, the
power will automatically turn off.
HT-H6500WM_30WM_ZC-0514.indd 14HT-H6500WM_30WM_ZC-0514.indd 14 2014-05-15  11:52:472014-05-15  11:52:47
15 - English
Settings
Accessing the Settings Screen
1. Select Settings on the Home screen, and then
press
OK. The Settings screen appears.
Picture
3D Settings
TV Aspect Ratio
16:9 Original
BD Wise Off
Resolution Auto
Movie Frame (24Fs) Auto
DVD 24Fs Conversion Off
Fit Screen Size Size 3
Picture
Sound
Network
Smart Hub
System
Support
Settings
2. To access the menus, sub-menus, and options
on the Settings screen, please refer to the
remote control illustration below.
Buttons on the Remote Control Used
for the Settings Menu
2
4
1
3
1
HOME Button : Press to move to the Home
screen.
2
'
(RETURN) Button : Press to return to the
previous menu.
3
OK / DIRECTION Button :
Press
,.
to move the cursor or
select an item.
Press the
OK button to activate the
currently selected item or confirm a
setting.
4
e
(
EXIT) Button : Press to exit the current
menu.
Detailed Function Information
Each Settings function, menu item, and individual
option is explained in detail on-screen. To view an
explanation, use the
,.
buttons to select the
function, menu item, or option. The explanation will
usually appear on the right of the screen.
A short description of each Settings function
starts below. Additional information on some of the
functions is also in the Appendix of this manual.
Settings Menu Functions
Picture
3D Settings
Set up the 3D related functions.
3D Blu-ray Playback Mode: Select whether to
play a Blu-ray Disc with 3D contents in 3D Mode. If
you move to the Home or Smart Hub Home menu
while in 3D mode, the product will switch to 2D
automatically.
Screen Size: Enter the size of the TV attached to
the product. The product will automatically adjust
the 3D output to the screen size of the TV.
Carefully read the health and safety information
before viewing
3D content. (See page 4)
TV Aspect Ratio
Lets you adjust the output of the product to the
screen size of your TV. (See page 49)
BD Wise
BD Wise is Samsung’s latest inter-connectivity
feature.
When you connect a Samsung product and a
Samsung TV with BD Wise to each other via
HDMI, and BD Wise is on in both the product
and TV, the product outputs video at the video
resolution and frame rate of the Blu-ray/DVD Disc.
Resolution
Lets you set the output resolution of the HDMI
video signal to BD Wise, Auto, 1080p, 1080i,
720p, 480p. The number indicates the number
of lines of video per frame. The i and p indicate
interlaced and progressive scan, respectively.
The more lines, the higher quality.
HT-H6500WM_30WM_ZC-0514.indd 15HT-H6500WM_30WM_ZC-0514.indd 15 2014-05-15  11:52:492014-05-15  11:52:49
16 - English
Settings
Movie Frame (24Fs)
Setting the Movie Frame (24Fs) feature to Auto
lets the product adjust its HDMI output to 24
frames per second automatically for improved
picture quality if attached to a 24Fs compatible TV.
You can enjoy the Movie Frame (24Fs) feature
only on a TV supporting this frame rate.
Movie Frame is only available when the product
is in the HDMI 1080p output resolution modes.
DVD 24Fs Conversion
Converts DVD playback to 24 frames per second
and outputs it via HDMI. This option is only
available when Movie Frame (24Fs) is set to on.
Fit Screen Size
Lets you select the optimal size for the Smart Hub
or Screen Mirroring screen.
HDMI Color Format
Lets you set the color space format for the HDMI
output to match the capabilities of the connected
device (TV, monitor, etc).
HDMI Deep Color
Lets you set the product to output video from
the HDMI OUT jack with Deep Color. Deep Color
provides more accurate color reproduction with
greater color depth.
Progressive Mode
Lets you improve picture quality when viewing
DVDs.
Sound
Simple Speaker Setup
Lets you configure the settings of the speakers you
have connected to obtain the best possible surround
sound.
Normal Mode: Select if you have set up your
speakers in the recommended speaker layout
with the surround speakers next to or behind the
listening positions.
Simple Mode: Select if you have put your
surround speakers in front of the listening position.
Downmixes the front sound to the surround sound
speakers.
SFE, Virtual 7.1 will not operate when the
simple mode is on.
Speaker Settings
Sound Output : Lets you select which speakers
are active, either the TV's speakers or the home
theater's speakers.
Settings (Home Theater Speakers) : Lets you
adjust the following speaker settings and turn the
test tone on and off so you can test the speakers.
- Volume Level : Lets you adjust the relative
loudness of each speaker from 6dB to -6dB. For
example, if you like deep bass, you can increase
the loudness of the subwoofer by 6dB.
- Distance
:
Lets you adjust the relative
distance of each speaker from the listening
position up to 30 feet. The farther the
distance, the louder the speaker will be.
- Speaker Test
:
Begins a test to set the best
surround sound configuration. Press Stop
Test to stop the test while it is in progress.
Settings (Multiroom Link) : You can enjoy
sound through a remote speaker that is
connected to the home theater through your
home network. To use the network speaker,
select Multiroom. If there is a network speaker
available, it will appear on the screen.
- Don't Use : The network speaker is not used.
- Multiroom : The network speaker outputs
audio. All network speakers output the same
audio regardless of channel using the PCM
format only.
SOUND EFFECT and 3D SOUND are not
applied if Multiroom is set to on.
The network speaker is not available when
Screen Mirroring is active.
For further details, refer to the Multiroom Link
manual from the web site.
www.samsung.com > Support > Search for the
product name > Multiroom Link > Download PDF
Sound Customizer
Sound Customizer lets you calibrate the home
theater for the optimal sound quality based on your
hearing level and the ambient conditions.
To create a Custom Sound Profile, follow these
steps:
1. In the Sound Customizer Menu, select Add
Custom Sound.
2. On the next screen, select Start. The Preview
screen appears.
3. Select Preview to preview the Test Sound.
Select Next, and then press OK to continue.
HT-H6500WM_30WM_ZC-0514.indd 16HT-H6500WM_30WM_ZC-0514.indd 16 2014-05-15  11:52:502014-05-15  11:52:50
17 - English
Settings
4. A 6-step test will start. During each stage,
the TV will sound a test tone at a different
frequency. The tone will begin softly and
increase in volume. Select Yes when you can
hear the test tone. If you want to listen to it
again, select Retry. Each time you select
Yes, the TV will move on to the next tone.
Once the test is complete, a screen appears
that lets you compare the original sound to
the calibrated sound.
5. Select Next, and then press the
OK button to
continue. The on-screen keyboard appears
with a default profile name.
6. Enter a name for the calibrated sound profile
or accept the default name, select Done, and
then press the OK button.
7. Select Done on the next screen, and then
press the
OK button. The Sound Customizer
screen reappears.
Custom Sound Profile : Select a Sound Profile
you created to activate it. Or select Hearing
Impaired, a Custom Sound Profile especially
composed of large sounds for those with hearing
disorders.
If there are more than 3 Custom Sounds
registered, Family mode will be activated which
is composed of the average value of all registered
profiles.
Add Custom Sound : Create and add a new
Custom Sound Profile. See the instructions
above.
Edit Custom Sound : Choose a Custom Sound
Profile to modify it. Follow the same steps you
used when creating a sound profile. This function is
only available if you have added a Custom Sound
Profile using Add Custom Sound. (See above.)
Manage Custom Sound : Rename or delete
Custom Sound Profiles. This function is only
available if you have added a Custom Sound
Profile using Add Custom Sound. To select a
profile, highlight the check box to the right of the
profile, and then select Rename or Delete.
Equalizer
Lets you configure the Equalizer settings manually.
Smart Volume
Lets you set the product so that the volume
remains stable when a scene change occurs or
when you change the channel.
Audio Return Channel (ARC)
Lets you direct the sound from the TV to the Home
Theater speakers. Requires an HDMI connection
and an Audio Return Channel (ARC) compatible
TV.
If Audio Return Channel is set to On and you
are using an HDMI cable to connect the product
to the TV, digital optical input is disabled.
If Audio Return Channel is set to Auto and you
are using an HDMI cable to connect the product
to the TV, ARC or digital optical input is selected
automatically.
Digital Output
Lets you set the Digital Output to match the
capabilities of the AV receiver you’ve connected to
the product. For more details, please refer to the
digital output selection table. (See page 55)
Dynamic Range Control
Lets you apply dynamic range control to Dolby
Digital, Dolby Digital Plus, and Dolby TrueHD audio.
Auto: Automatically controls the dynamic range
of Dolby TrueHD audio, based on information
in the Dolby TrueHD soundtrack. Also turns
dynamic range control off for Dolby Digital and
Dolby Digital Plus.
Off: Leaves the dynamic range uncompressed,
letting you hear the original sound.
On: Turns dynamic range control on for all three
Dolby formats. Quieter sounds are made louder
and the volume of loud sounds is reduced.
Downmixing Mode
Lets you select the multi-channel downmix method
that is compatible with your stereo system. You
can choose to have the product downmix to
Normal Stereo or to Surround Compatible.
Audio Sync
When the product is attached to a digital TV, lets
you adjust the audio delay so that the audio syncs
with the video. You can set the delay between 0
and 300 milliseconds.
The Auto function in Audio Sync is guaranteed
to work only with a Samsung TV that supports
the ARC function (the Anynet+ function).
HT-H6500WM_30WM_ZC-0514.indd 17HT-H6500WM_30WM_ZC-0514.indd 17 2014-05-15  11:52:502014-05-15  11:52:50
18 - English
Settings
Network
Network Status
Lets you check the current network and Internet
status.
Network Settings
Lets you configure the network connection so
you can enjoy various features such as Internet
services or AllShare Wi-Fi functionality, and perform
software upgrades.
Wi-Fi Direct
Lets you connect a Wi-Fi Direct device to the
product using a peer-to-peer network, without the
need for a wireless router. Note that if the product
is connected to a wireless network, it may be
disconnected when you use Wi-Fi Direct. (See
page 23)
Text files, such as files with a .TXT or .DOC
extension, will not display when you are using the
Wi-Fi Direct function.
Multimedia Device Settings
Allow other devices on your network, such as smart
phones and tablets, to share content with your
product.
Device Name
Lets you assign an identifying name to the product.
You use this name to identify the product when
you are connecting external Wi-Fi devices (smart
phones, tablets, etc.) to it.
BD-Live Settings
Lets you set various BD-Live functions. BD-Live
allows you to access extra features available on
some Blu-ray Discs if you are connected to the
Internet.
BD-Live Internet Connection : Lets you fully
allow, partly allow, or prohibit a BD-Live Internet
connection.
BD Data Management : Manage BD data
downloaded from a BD-Live service or Blu-ray
Disc.
To use BD-Live, you must insert a USB storage
device into the home theater's USB port.
Smart Hub
VOD Rating Lock
Lets you lock access to Video on Demand (VOD)
content based on its rating. To use, you must enter
the security PIN.
Press and hold the 123 button until
the Num pad appears on the screen. When the Num
pad appears, select a number using the
,.
button and then press the
OK
button.
The default security PIN is 0000.
Depending on your country, this menu function
may not be supported.
Caption
Use to modify captions on VOD playback that
supports closed captions. Lets you change
displayed caption's font color and size.
The Caption function does not work with VOD
services that don't support closed captions.
For some VOD services that do support closed
captions, the functions settings may not be
applied.
Depending on your country, this menu function
may not be supported.
Terms & Policy
Samsung Account Terms and Conditions,
Privacy Policy
You can view the terms of use and privacy policy
for Smart Hub, Samsung accounts, and various
other services
Reset Smart Hub
Resets all Smart Hub settings to their default
settings. To use, you must enter the security PIN.
Press and hold the 123 button until the Num pad
appears on the screen. When the Num pad appears,
select a number using the
,.
button and then
press the
OK
button.
The default security PIN is 0000.
HT-H6500WM_30WM_ZC-0514.indd 18HT-H6500WM_30WM_ZC-0514.indd 18 2014-05-15  11:52:502014-05-15  11:52:50
19 - English
Settings
System
Setup
Lets you re-run the Initial Settings procedure.
Refer to the descriptions displayed on the screen.
Quick Start
Lets you set the player to turn on quickly by
decreasing the boot time.
If this function is set to On, Standby power
consumption will increase. (About 12W ~ 20W)
Language
Lets you select the language you prefer for the on-
screen menu, disc menu, audio, subtitles, etc.
The language you select for the disc menu,
disc audio, or subtitles will only appear if it is
supported on the disc.
Device Manager
Lets you connect a wireless USB keyboard or
mouse to the USB port on the front of the product.
Keyboard Settings: Lets you configure a wireless
USB keyboard connected to the product.
You can use the keyboard only when a
QWERTY keyboard screen or window appears
in the Web Browser.
Mouse Settings: Lets you configure a wireless
USB mouse connected to the product. You can
use the mouse in the product's menu in the
same way you use a mouse on your PC.
To use a mouse with the product's menu:
1. Connect the USB mouse to the
product
.
2. Click the primary button you selected in
Mouse Settings. The Simple Menu appears.
3. Click the menu options you want.
Some USB HID keyboards and mice may not be
compatible with your product.
Some HID keyboard keys may not work.
Wired USB keyboards are not supported.
Some applications may not be supported.
If a wireless HID Keyboard does not operate
because of interference, move the keyboard closer
to the
product.
Security
Press and hold the 123 button until the Num pad
appears on the screen. When the Num pad appears,
select a number using the
,.
button and then
press the
OK
button.
The default security PIN is
0000. Enter the default PIN to access the security
function if you haven't created your own PIN.
BD Parental Rating:
Prevents playback of
Blu-ray Discs with a rating equal to or above a
specific age rating you have set unless you enter
the PIN.
DVD Parental Rating: Prevents playback of DVDs
with a rating above a specific numerical rating you
have set unless you enter the PIN.
Change PIN: Lets you change the 4-digit PIN used
to access security functions.
If you forget your PIN
1. Remove any disc or USB storage device.
2. Press and hold the
@
button on the front
panel for 5 seconds or more.
All settings will revert to the factory default
settings.
When the factory default settings are restored,
all the user stored BD data is deleted.
General
Lets you specify the display brightness and time
zone.
Front Display: Lets you change the brightness of
the front panel.
Time Zone: You can specify the time zone that is
applicable to your area.
Menu Transparency: Lets you adjust the
transparency of the menu box.
Anynet+ (HDMI-CEC)
Anynet+ is a convenient function that offers linked
operations with other Samsung products that have
the Anynet+ feature, and lets you control those
products with one Samsung TV remote. To operate
this function, you must connect this product to an
Anynet+ Samsung TV using an HDMI cable.
HT-H6500WM_30WM_ZC-0514.indd 19HT-H6500WM_30WM_ZC-0514.indd 19 2014-05-15  11:52:512014-05-15  11:52:51
20 - English
Settings
To use an Anynet+ (HDMI-CEC) function, follow
the instructions below.
1) Connect the product to an Anynet+ (HDMI-
CEC)-compliant Samsung TV using HDMI
Cable.
2) Set the Anynet+ (HDMI-CEC) feature to On
in both the TV and the product.
3) Search for and then select the product in the
TV's Anynet+ (HDMI-CEC) list. For more
exact instructions, see the Anynet+ section of
the TV's user's manual.
Support
Remote Management
When activated, lets Samsung Call Center agents
diagnose and fix problems with the product
remotely. Requires an active Internet connection.
Remote Management service might not be
available in some countries.
Software Update
For more information about the Software Update
function, see "Upgrading Software" on page 24.
Use Mode
Lets you set the Use Mode. If you are using the
home theater at home, always select Home Use.
Store Demo is for retail display settings only.
Contact Samsung
Provides contact information for assistance with
your product.
Reset
Reverts all settings to their defaults except for the
network and Smart Hub settings. Requires that
you enter your security PIN.
Press and hold the 123
button until the Num pad appears on the screen.
When the Num pad appears, select a number using
the
,.
button and then press the
OK
button.
The default security PIN is 0000.
Network Setup
When you connect this product to a network, you
can use network based applications and functions
such as Smart Hub and BD-LIVE, and upgrade the
product's software through the network connection.
For more information about accessing and using
Internet services, see the Network Services chapter
of this manual on pages 41~48. Instructions for
configuring the network connection start below.
Configuring Your Network Connection
If you didn't configure your network connection during
the initial settings procedure or you need to reset the
network connection, follow the directions below.
Before you begin, contact your Internet Service
Provider to find out if your IP address is static or
dynamic. If it is dynamic, and you have a wired
or wireless network, we recommend using the
Automatic configuration procedures described below.
If you are connecting to a wired network, connect the
product to your router using a LAN cable before you
start the configuration procedure.
To begin configuring your network connection, follow
these steps:
1. In the Home screen, select Settings, and then
press the
OK button.
2. Select Network, and then press the
OK button.
3. Select Network Settings, and then press the
OK button.
4. Go to the instructions for Wired networks
starting below or the instructions for Wireless
networks starting on page 21.
Wired Network
Wired – Automatic
After following Steps 1 to 3 above:
1. In the Network Settings screen, change
Network type to Wired. Then, select Connect
and press the OK button. The product detects
the wired connection, verifies the network
connection, and then connects to the network.
2. When it is done, highlight OK, and then press
OK button.
HT-H6500WM_30WM_ZC-0514.indd 20HT-H6500WM_30WM_ZC-0514.indd 20 2014-05-15  11:52:512014-05-15  11:52:51
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128

Samsung HT-H6500WM Manuel utilisateur

Catégorie
Lecteurs Blu-Ray
Taper
Manuel utilisateur

dans d''autres langues