Samsung HT-H4550K Manuel utilisateur

Catégorie
Lecteurs Blu-Ray
Taper
Manuel utilisateur
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
5.1CH Blu-ray™
Home Entertainment System
user manual
HT-H4500K
HT-H4530HK
HT-H4530K
HT-H4550K
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 1HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 1 2014-05-08  11:34:012014-05-08  11:34:01
2 - English
Safety Information
The slots and openings in the cabinet and in the back
or bottom are provided for necessary ventilation. To
ensure reliable operation of this apparatus, and to
protect it from overheating, these slots and openings
must never be blocked or covered.
- Do not place this apparatus in a confined space,
such as a bookcase, or built-in cabinet, unless
proper ventilation is provided.
- Do not place this apparatus near or over a radiator
or heat register, or where it is exposed to direct
sunlight.
- Do not place vessels (vases etc.) containing water
on this apparatus. A water spill can cause a fire or
electric shock.
Do not expose this apparatus to rain or place it near
water (near a bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming
pool, etc.). If this apparatus accidentally gets wet,
unplug it and contact an authorized dealer immediately.
This apparatus uses batteries. In your community,
there might be environmental regulations that require
you to dispose of these batteries properly. Please
contact your local authorities for disposal or recycling
information.
Do not overload wall outlets, extension cords or
adaptors beyond their capacity, since this can result in
fire or electric shock.
Route power-supply cords so that they are not likely to
be walked on or pinched by items placed on or against
them. Pay particular attention to cords at the plug end,
at wall outlets, and the point where they exit from the
apparatus.
To protect this apparatus from a lightning storm, or
when it is left unattended and unused for long periods
of time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent damage
to the set due to lightning and power line surges.
Before connecting the AC power cord to the DC
adaptor outlet, make sure the voltage designation of
the DC adaptor corresponds to the local electrical
supply.
Never insert anything metallic into the open parts
of this apparatus. Doing so may create a danger of
electric shock.
To avoid electric shock, never touch the inside of this
apparatus. Only a qualified technician should open this
apparatus.
Make sure to plug the power cord in until it is firmly
seated. When unplugging the power cord from a wall
outlet, always pull on the power cord's plug. Never
unplug by pulling on the power cord. Do not touch the
power cord with wet hands.
If this apparatus does not operate normally - in
particular, if there are any unusual sounds or smells
coming from it - unplug it immediately and contact an
authorized dealer or service centre.
Maintenance of Cabinet.
- Before connecting other components to this
product, be sure to turn them off.
- If you move your product suddenly from a cold place
to a warm place, condensation may occur on the
operating parts and lens and cause abnormal disc
playback. If this occurs, unplug the product, wait for
two hours, and then connect the plug to the power
outlet. Then, insert the disc, and try to play back
again.
Be sure to pull the power plug out of the outlet if the
product is to remain unused or if you are leaving the
house for an extended period of time (especially when
children, elderly, or disabled people will be left alone in
the house).
- Accumulated dust can cause an electric shock, an
electric leakage, or a fire by causing the power cord
to generate sparks and heat or the insulation to
deteriorate.
Contact an authorized service centre for information
if you intend to install your product in a location with
heavy dust, high or low temperatures, high humidity,
chemical substances, or where it will operate 24 hours
a day such as in an airport, a train station, etc. Failing
to do so may lead to serious damage of your product.
Use only a properly grounded plug and wall outlet.
- An improper ground may cause electric shock or
equipment damage. (Class l Equipment only.)
To turn this apparatus off completely, you must
disconnect it from the wall outlet. Consequently, the
wall outlet and power plug must be readily accessible
at all times.
Do not allow children to hang on the product.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE THE COVER (OR BACK). THERE ARE NO USER
SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO
QUALIFIED PERSONNEL.
This symbol indicates that high voltage is
present inside. It is dangerous to make
any kind of contact with any internal part
of this product.
This symbol indicates that important
literature concerning operation and
maintenance has been included with this
product.
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 2HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 2 2014-05-08  11:34:352014-05-08  11:34:35
3 - English
Safety Information
Store the accessories (battery, etc.) in a location safely
out of the reach of children.
Do not install the product in an unstable location such
as a shaky self, a slanted floor, or a location exposed
to vibration.
Do not drop or strike the product. If the product is
damaged, disconnect the power cord and contact a
service centre.
To clean this apparatus, unplug the power cord from
the wall outlet and wipe the product using a soft,
dry cloth. Do not use any chemicals such as wax,
benzene, alcohol, thinners, insecticide, air fresheners,
lubricants, or detergent. These chemicals can damage
the appearance of the product or erase the printing on
the product.
Do not expose this apparatus to dripping or splashing.
Do not put objects filled with liquids, such as vases on
the apparatus.
Do not dispose of batteries in a fire.
Do not plug multiple electric devices into the same wall
socket. Overloading a socket can cause it to overheat,
resulting in a fire.
There is danger of an explosion if you replace the
batteries used in the remote with the wrong type of
battery. Replace only with the same or equivalent type.
WARNING :
TO PREVENT THE SPREAD OF FIRE,
KEEP CANDLES AND OTHER ITEMS
WITH OPEN FLAMES AWAY FROM THIS
PRODUCT AT ALL TIMES.
CLASS 1 LASER PRODUCT
This product is classified as a CLASS 1 LASER product.
Use of controls, adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
CAUTION :
INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED, AVOID EXPOSURE TO
BEAM.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LÁSER CLASE 1
3D Precautions
IMPORTANT HEALTH AND SAFETY INFORMATION FOR
3D PICTURES.
Read and understand the following safety information
before using the 3D function.
Some viewers may experience discomfort while viewing
3D TV such as dizziness, nausea, and headaches.
If you experience any such symptom, stop viewing 3D
TV, remove the 3D Active Glasses, and rest.
Watching 3D images for an extended period of time
may cause eye strain. If you feel eye strain, stop
viewing 3D TV, remove your 3D Active Glasses, and
rest.
A responsible adult should frequently check on children
who are using the 3D function.
If there are any reports of tired eyes, headaches,
dizziness, or nausea, have the child stop viewing 3D
TV and rest.
Do not use the 3D Active Glasses for other purposes
(such as general eyeglasses, sunglasses, protective
goggles, etc.)
Do not use the 3D function or 3D Active Glasses while
walking or moving around. Using the 3D function or 3D
Active Glasses while moving around may cause you to
bump into objects, trip, and/or fall, and cause serious
injury.
If you want to enjoy 3D content, connect a 3D device
(3D compliant AV receiver or TV) to the product’s HDMI
OUT port using a high-speed HDMI cable. Put on 3D
glasses before playing the 3D content.
The product outputs 3D signals only through an HDMI
cable connected to the HDMI OUT port.
The video resolution in 3D play mode is fixed to the
resolution of the original 3D video. You can not change
the resolution.
Some functions such as BD Wise, screen size
adjustment, and resolution adjustment may not operate
properly in 3D play mode.
You must use a high-speed HDMI cable for proper
output of the 3D signal.
Stay at least three times the width of the screen from
the TV when watching 3D images. For example, if
you have a 46 inch screen, stay 3.5 meters from the
screen.
Place the 3D video screen at eye level for the best 3D
picture.
When the product is connected to some 3D devices,
the 3D effect may not function properly.
This product does not convert 2D content into 3D.
"Blu-ray 3D" and "Blu-ray 3D" logo are trademarks of
the Blu-ray Disc Association.
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 3HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 3 2014-05-08  11:34:372014-05-08  11:34:37
4 - English
Contents
GETTING STARTED
5 Accessories
5 Speaker Components
7 Front Panel
7 Rear Panel
8 Remote Control
CONNECTIONS
9 Connecting the Speakers
12 Connecting to a Network Router
13 Connecting to a TV and External Devices
SETTINGS
14 The Initial Settings Procedure
15 The Home Screen at a Glance
15 Accessing the Settings Screen
16 Settings Menu Functions
19 Network Setup
20 Upgrading Software
21 Setting Up DLNA
PLAYING CONTENT
22 Switching the Source Device
22 Playing Commercial Discs
22 Playing a Disc with User Recorded Content
23 Playing Files on a USB Device
24 Controlling Video Playback
25 Playing a Pre-Recorded Commercial Audio Disc
26 Controlling Music Playback
27 Playing Photo Contents
28 Listening to the Radio
28 Using Karaoke
29 Using Bluetooth
30 Using the Special Effects Remote Control
Buttons
NETWORK SERVICES
32 Using BD-LIVE™
32 Using DLNA
32 Apps
33
Using Opera TV Store
APPENDIX
34 Additional Information
35 Disk and Format Compatibility
40 Troubleshooting
43 Specifications
45 Licences
Figures and illustrations in this User Manual
are provided for reference only and may differ
from actual product appearance.
An administration fee may be charged if either
a. an engineer is called out at your request
and there is no defect in the product (i.e.
where you have failed to read this user
manual)
b. you bring the unit to a repair centre and
there is no defect in the product (i.e. where
you have failed to read this user manual).
The amount of such administration charge will
be advised to you before any work or home
visit is carried out.
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 4HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 4 2014-05-08  11:34:392014-05-08  11:34:39
5 - English
Getting Started
Check the box for the accessories and speaker components listed or shown below.
Accessories
Remote Control User Manual Batteries
Power Cable FM Antenna HDMI Cable
Speaker Components
HT-H4500K
Front x 2 Surround x 2 Centre Subwoofer
HT-H4530HK
Stand Nut
x 2
Stand Driver
Front x 2
Stand Base x 2
Surround x 2 Centre Subwoofer
Getting Started
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 5HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 5 2014-05-08  11:34:422014-05-08  11:34:42
6 - English
Getting Started
HT-H4530K
Stand Base x 2
Speaker Cable
x 2
Screw (5x15) x 8
Front x 2 Stand x 2 Surround x 2 Centre Subwoofer
HT-H4550K
Screw (5x15) x 16
Speaker Cable
x 4 Centre
Front x 2/Surround x 2 Stand x 4
Stand Base x 4
Subwoofer
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 6HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 6 2014-05-08  11:34:532014-05-08  11:34:53
7 - English
Getting Started
Front Panel
MIC JACK
DISPLAY ICONS
FUNCTION STOP PLAY/PAUSE
OPEN/
CLOSE
VOLUME
CONTROL
POWER
5V 0.5A
MIC 2MIC 1
USBREMOTE CONTROL SENSOR
DISPLAY
DISC TRAY
When the product is on, do not let children touch the product's surface. It will be hot.
To upgrade the product's software through the USB jack, you must use a USB flash drive.
When the product displays the Blu-ray Disc menu, you cannot start the movie by pressing the /
6
button
on the product or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and
then press the
E
button.
If you are using the Internet or are playing content from a USB device on your TV through the home cinema,
you cannot select the BD/DVD mode with the
FUNCTION button. To select the BD/DVD mode, exit the
Internet or stop the content you are playing on the TV, and then select the BD/DVD mode.
Plug the microphone jack before using Karaoke function.
Rear Panel
SURROUND
SURROUND
COOLING FAN
* FM ANTENNA
AUX IN
HDMI OUT
SPEAKER OUTPUT
CONNECTORS
POWER CORD LAN TERMINALEXTERNAL DIGITAL
AUDIO IN (OPTICAL)
* Connecting the FM Antenna
1. Connect the supplied FM antenna to the FM ANT Jack.
2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a
wall or other rigid surface.
Maintain a minimum of 10cm of clear space on all sides of the home cinema to ensure adequate ventilation.
Do not obstruct the cooling fan or ventilation holes.
This product does not receive AM broadcasts.
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 7HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 7 2014-05-08  11:35:032014-05-08  11:35:03
8 - English
Getting Started
Installing batteries in the Remote Control
Make sure to match the “+” and “–” ends of the batteries with
the diagram inside the compartment.
Assuming typical usage, the batteries last for about one year.
The remote control can be used up to approximately 7 meters
from the product in a straight line.
Battery size: AAA
Remote Control
Tour of the Remote Control
Turn the product on and off.
Adjust the volume.
Press numeric buttons to operate
options.
Press to skip backwards or forwards.
Press to use the karaoke function
(Mic. vol., Echo, Key Cotrol).
Press to move to the Home screen.
Select on-screen menu items
and change menu values.
Return to the previous menu.
These buttons are used both for
menus on the product and also
several Blu-ray Disc functions.
Press to view the disc menu.
Press to use the Tools menu.
Press to play a disc or files.
Press to direct audio signal to home
cinema speaker or TV speaker.
(See page 30)
Select the desired DSP/EQ audio
mode.
Press to stop a disc or files.
Cut off the sound temporarily.
Press to search backwards or
forwards.
Press to pause playing.
Allows you to repeat a title,
chapter, track or disc.
Use to enter the Popup menu/
Title menu.
Select MONO or STEREO for radio
broadcasts.
Search for active FM stations and
to change channels.
Use to display the playback
information when playing
a Blu-ray/DVD disc or files.
To open and close the disc tray.
Press to exit the menu.
Press to select Home Cinema's
mode. (BD/DVD, D. IN, AUX,
etc.).
Use to set a preset radio frequency.
TOOLS
RETURN
EXIT
INFO
KARAOKE HOME
REPEAT
1
2
3
7
89
DISC MENU TITLE MENU
0
POPUP
4
56
MUTE
MO/ST
TUNER
MEMORY
DPS/EQTV SOUND
ABCD
TUNING
DOWN
UP
VOLUME
-
+
FUNCTION
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 8HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 8 2014-05-08  11:35:062014-05-08  11:35:06
9 - English
Connections
This section describes various methods of connecting the product to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Connecting the Speakers
Surround (L)
Surround (R)
Product
Centre
Subwoofer
Front (L)
Front (R)
Position of the product
Place it on a stand or cabinet shelf, or
under the TV stand.
Selecting the Listening Position
The listening position should be
located about 2.5 to 3 times the TV's
screen size away from the TV. For
example, if you have a 46 inch screen,
locate the listening position 2.92 to
3.50 meters from the screen.
Front Speakers
Place these speakers in front of your listening position, facing inwards (about
45°) toward you. Place the front speakers so that their tweeters will be at the
same height as your ear. Align the front face of the front speakers with the front
face of the centre speaker or place them slightly in front of the centre speakers.
Centre Speaker
It is best to install the Centre Speaker at the same height as the front speakers.
You can also install it directly over or under the TV.
Surround Speakers
Place these speakers to the side of your listening position. If there isn't enough
room, place these speakers so they face each other. Position them about 60 to
90cm above your ear, facing slightly downward.
* Unlike the front and centre speakers, the surround speakers are used mainly
for sound effects. Sound will not come from them all the time.
Subwoofer
The position of the subwoofer is not so critical. Place it anywhere you like.
* The appearance of your speakers may differ from the illustrations in this manual.
* Match the speaker cables to the coloured label on the back of the speaker, and then plug them into
the jack of the same colour. See page 11 for exact instructions.
Connections
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 9HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 9 2014-05-08  11:35:112014-05-08  11:35:11
10 - English
Connections
Installing the Speakers on the Half Tallboy Stand
* HT-H4530HK only - Front Speakers
1. Stretch out the speaker cables as shown and arrange it
through the hole of the stand base .
2. When done, use the stand driver to tighten the stand
nut as shown.
3. This is the appearance after the speaker is installed.
Follow these steps to install another speaker.
4. If you want to adjust the height of the speaker, loosen
two screws on the rear of the speaker.
5. Pull up the speaker in the arrow direction. Fit the
speaker in a height adjusting hole of your choice.
| CAUTION |
Be careful as an excessive force may result in a physical
damage.
6. Insert two screws clockwise into the hole on the rear of
the speaker using a screwdriver as shown and tighten
back 2 screws.
7. This is after the height of the speaker is adjusted. You
can repeat these steps above at any time if you want to
readjust the height.
Installing the Speakers on the Tallboy Stand
* HT-H4530K only - Front Speakers
* HT-H4550K only - Front/Surround Speakers
1. Turn the Stand Base upside-down and connect it
to the Stand.
2. Use the driver to combine the screws on the 3
marked holes.
1
Stand Base
Stand
2
21
5 6
7
43
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 10HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 10 2014-05-08  11:35:152014-05-08  11:35:15
11 - English
Connections
3. Straighten a supplied speaker wire and put in the
hole on the centre of Stand Base.
4. Connect the upper Speaker to the assembled
Stand.
5. Insert a screw clockwise into the hole on the rear
of the speaker using a screwdriver.
And then connect a speaker cable.
6. This is the appearance after the speaker is
installed.
Follow this steps to install other speaker.
Speaker Cable Connections
* HT-H4530K only - Front Speakers
* HT-H4550K only - Front/Surround Speakers
1. Match each speaker cable bundle to the correct speaker by matching the colour coded plug on each
bundle to the coloured sticker on the bottom of each speaker.
2. Connect the speaker wire plugs from each speaker to the back of the product by matching the colours of
the speaker plugs to the colours of the speaker jacks.
In case of HT-H4530K
SURROUND
SURROUND
SURROUND
SURROUND
Centre Speaker
Subwoofer
Front Speaker (L)
Front Speaker (R)
Surround Speaker (L)
Surround Speaker (R)
* Refer to page 5~6 for the speakers of HT-H4500K/HT-H4530HK/HT-H4550K.
3
4
Speaker
Stand
5 6
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 11HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 11 2014-05-08  11:35:322014-05-08  11:35:32
12 - English
Connections
If you place a speaker near your TV set, the screen colour may be distorted because of the magnetic field.
| CAUTION |
If you want to install the speakers on the wall, fasten screws or nails (not provided) firmly to the wall wherever
you want to hang a speaker, and then, using the hole in the rear of each speaker, carefully hang each
speaker on a screw or nail.
Do not let children play with or near the speakers. They could get hurt if a speaker falls.
When connecting the speaker wires to the speakers, make sure that the polarity (+/ –) is correct.
Keep the subwoofer speaker out of reach of children to prevent children from inserting their hands or alien
substances into the duct (hole) of the subwoofer speaker.
Do not hang the subwoofer on the wall through the duct (hole).
Connecting to a Network Router
SURROUND
L
SURROUND
R
Broadband
service
Broadband
service
Broadband
modem
Or
Broadband modem (with integrated router)
Router
Your router or your Internet Service Provider's policies may prevent the product from accessing Samsung's
software update server. If this occurs, contact your Internet Service Provider (ISP) for more information.
DSL users, please use a router to make a network connection.
To use the DLNA function, you must connect a PC to the network as shown in the figure.
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 12HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 12 2014-05-08  11:35:372014-05-08  11:35:37
13 - English
Connections
Connecting to a TV and External Devices
OPTICAL OUT
AUDIO OUT
HDMI IN
SURROUND
L
SURROUND
R
Method 1 Method 2
R
Red
W
White
External Devices
Connecting to a TV
Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN jack on your TV.
If the TV supports ARC, you can hear the audio from your TV through the home cinema with only this cable
connected. See page 17 in this manual and the section on ARC in your TV's user's manual for details.
Connecting to External Devices
To select the correct mode for an external device after you have connected the device, press the FUNCTION
button. Each time you press the button, the mode changes in this order :
BD/DVD
D. IN
AUX
FM
BT
Two methods of connecting external devices to your home cinema are explained below.
Method 1 AUX IN : Connecting an External Analogue Component
Using an RCA audio cable (not supplied), connect the AUDIO In jack on the product to the AUDIO Out jack on
the external analogue component.
Select the AUX mode.
Be sure to match the colours on the cable plugs to the colours on the input and output jacks.
Method 2 OPTICAL : Connecting an External Digital Audio Component
Use to connect the digital audio output of digital signal components such as Cable Boxes and Satellite
Receivers (Set-Top-Boxes): Using a digital optical cable (not supplied), connect the Optical Digital Audio In jack
on the product to the Digital Optical Out jack of the external digital device using a digital optical cable.
Select the D. IN mode.
To see video from your Cable Box/Satellite receiver, you must connect its video output directly to your TV.
This system supports Digital sampling frequencies of 32 kHz or higher from external digital components.
This system supports only DTS and Dolby Digital audio. MPEG audio, a bitstream format, is not supported.
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 13HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 13 2014-05-08  11:35:402014-05-08  11:35:40
14 - English
Settings
The Initial Settings Procedure
The Home menu will not appear if you do not
configure the initial settings.
The OSD (On Screen Display) may change in
this product after you upgrade the software
version.
The access steps may differ depending on the
menu you selected.
1. Turn on your TV after connecting the product,
and then turn on the product. When you turn
on the product for the first time, the product
automatically displays the Initial Settings
Language screen.
2. Press the ▲▼ buttons to select the desired
language, and then press the
E
button.
3. Press the
E
button to start function setup.
Initial Settings
TV Aspect and Network will be set.
Each setting may be changed later under "Settings"
a
Previous
"
Select
Start
4. The TV Aspect screen appears. Press the ▲▼
buttons to select a TV aspect ratio, and then
press the
E
button.
You have four choices:
16:9 Original - For widescreen TVs. Displays
widescreen pictures in their original 16:9 format
and 4:3 pictures (the old, standard format) in 4:3
pillar box format with black bars on the left and
right.
16:9 Full - For widescreen TVs. Displays
widescreen pictures in their original 16:9 format
and expands 4:3 pictures to fill the 16:9 screen.
4:3 Letter Box - For older, standard screen,
analogue TVs. Displays 4:3 pictures in full screen
and 16:9 pictures in letter box format that retains
the 16:9 aspect ratio but puts black bars above
and below the picture.
4:3 Pan-Scan - For older, standard screen,
analogue TVs. Displays 4:3 pictures in full screen
and 16:9 pictures in Pan-Scan format that fills
the screen, but cuts off the left and right sides of
the picture and enlarges the middle vertically.
5. The Network - Wired screen appears.
- If you have a network with dynamic IP
addresses - and most people do - select
Auto, press the
E
button, and then go to
Step 6.
- If you have a network with static IP addresses,
we suggest you select Skip by pressing the
BLUE (D) button. (See page 19)
- If you have no network, select Skip by
pressing the
BLUE (D) button. The Initial
Settings Complete screen appears, and then
the Home screen appears.
If you skip network setup here or the setup does
not work correctly, you can set up the product's
network connection later. (See page 19)
Initial Settings | Network - Wired
Auto Manual
Choose the method to configure Internet Protocol (IP). Please make sure that Ethernet
cable is connected.
Auto : Configure IP automatically.
a Previous d Skip < Move " Select
6. The product verifies the network connection
and then connects to the network. When it is
done, press the
E
button. The "Initial settings
completed." screen appears, and then the
Home screen appears.
Initial Settings | Network - Wired
MAC Address (d0:66:7b:dc:28:fc)
IP Address, Subnet Mask, Gateway, DNS Server
Gateway Ping
Internet Service Test
" Select
OK
Your network is operating properly. If you still have a network problem, contact your
network service provider.
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 14HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 14 2014-05-08  11:35:422014-05-08  11:35:42
15 - English
Settings
If you want to display the Initial Settings screen
again and make changes, select the Reset
option. (See page 19)
If you use an HDMI cable to connect the product
to an Anynet+ (HDMI-CEC)-compliant Samsung
TV and 1.) You have set the Anynet+ (HDMI-CEC)
feature to On in both the TV and the product and
2.) You have set the TV to a language supported
by the product, the product will select that
language as the preferred language automatically.
The Home Screen at a Glance
Play disc
App 1 App 2 App 3 App 4
Change Device
Function
Blu-ray
Settings
Photos Videos Music
1
345678
2
Opera TV
Store
More
1
Play disc
The disc currently in the tray is displayed.
Press
E
to start playing the disc.
2
Photos/Videos/Music
Play photos, videos, or music content from Disc,
USB, PC, or mobile devices.
3
Apps
Access various for pay or free-of-charge
applications.
4
Opera TV Store
Makes the Web-based App for TV available for
use.
5
More
A list of useful and popular apps we recommend.
6
Change Device
Displays a list of external devices connected to the
main unit. Switch to the desired device.
7
Function
Use for switching to an external device, and
for radio and mode switching for a Bluetooth
connection. You can use the remote control’s
FUNCTION button and the main unit’s button
for mode switching.
8
Settings
Set various functions to suit your personal
preferences.
To play or view video, photo, music files located
on your PC, you must connect your home
cinema and PC to a home network and you
must download, install, and configure the DLNA
software on your PC. (See page 21)
Accessing the Settings Screen
1. Select Settings on the Home screen, and then
press
E
. The Settings screen appears.
Settings
Display
Audio
Network
System
Language
Security
General
Support
3D Settings
TV Aspect Ratio : 16:9 Original
BD Wise : Off
Resolution : Auto
Movie Frame (24 fps) : Off
HDMI Colour Format : Auto
HDMI Deep Colour : Off
Progressive Mode : Auto
2. To access the menus, sub-menus, and options
on the Settings screen, please refer to the
remote control illustration. (See page 16)
If you leave the product in the stop mode for more
than 5 minutes without using it, a screen saver
will appears on your TV. If the product is left in the
screen saver mode for more than 20 minutes, the
power automatically turns off.
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 15HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 15 2014-05-08  11:35:452014-05-08  11:35:45
16 - English
Settings
Buttons on the Remote Control Used
for the Settings Menu
TOOLS
RETURN
EXIT
INFO
KARAOKE HOME
REPEAT
TUNER
24
3
1
1
HOME Button : Press to move to the Home
screen.
2
RETURN Button : Press to return to the
previous menu.
3
E
(
ENTER) / DIRECTION Button :
Press
▲▼◄►
to move the cursor or
select an item.
Press the
E
button to activate the
currently selected item or confirm a
setting.
4
EXIT Button : Press to exit the current
menu.
Detailed Function Information
Each Settings function, menu item, and individual
option is explained in detail on-screen. To view an
explanation, use the ▲▼◄► buttons to select the
function, menu item, or option. The explanation will
usually appear on the bottom of the screen.
A short description of each Settings function starts
on this page. Additional information on some of the
functions is also in the Appendix of this manual.
Settings Menu Functions
Display
3D Settings
Set up the 3D related functions.
3D Blu-ray Playback Mode: Select whether to
play a Blu-ray Disc with 3D contents in 3D Mode.
If you move to the Home menu while in 3D mode,
the product will switch to 2D automatically.
Screen Size: Enter the size of the TV attached to
the product. The product will automatically adjust
the 3D output to the screen size of the TV.
Carefully read the health and safety information
before viewing 3D content. (See page 3)
TV Aspect Ratio
Lets you adjust the output of the product to the
screen size of your TV. (See page 34)
BD Wise
BD Wise is Samsung’s latest inter-connectivity
feature. When you connect a Samsung product
and a Samsung TV with BD Wise to each other
via HDMI, and BD Wise is on in both the product
and TV, the product outputs video at the video
resolution and frame rate of the Blu-ray/DVD Disc.
Resolution
Lets you set the output resolution of the HDMI
video signal to BD Wise, Auto, 1080p, 1080i,
720p, 576p/480p. The number indicates the
number of lines of video per frame. The i and
p indicate interlaced and progressive scan,
respectively. The more lines, the higher quality.
Movie Frame (24 fps)
Setting the Movie Frame (24 fps) feature to
Auto lets the product adjust its HDMI output to
24 frames per second automatically for improved
picture quality if attached to a 24Fs compatible TV.
You can enjoy the Movie Frame (24 fps) feature
only on a TV supporting this frame rate.
Movie Frame is only available when the product
is in the HDMI 1080p output resolution modes.
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 16HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 16 2014-05-08  11:35:482014-05-08  11:35:48
17 - English
Settings
HDMI Colour Format
Lets you set the colour space format for the HDMI
output to match the capabilities of the connected
device (TV, monitor, etc).
HDMI Deep Colour
Lets you set the product to output video from the
HDMI OUT jack with Deep Colour. Deep Colour
provides more accurate colour reproduction with
greater colour depth.
Progressive Mode
Lets you improve picture quality when viewing
DVDs.
Audio
Karaoke scoring
This feature rates your singing ability and gives you
a score for each song you sing.
My karaoke
Set the volume of the vocals when using the
karaoke feature.
Original Vocals: Volume is set to the level of the
original sound.
Reduce Vocals: Volume is set to a level lower than
that of the original sound.
Speaker Settings
Lets you adjust the following speaker settings and
turn the test tone on and off so you can test the
speakers.
Level
: Lets you adjust the relative loudness of
each speaker from 6dB to -6dB. For example, if
you like deep bass, you can increase the loudness
of the subwoofer by 6db.
Distance
: Lets you adjust the relative distance
of each speaker from the listening position up to
9 meters. The farther the distance, the louder the
speaker will be.
Test Tone
: Lets you run the Test Tone function so
you can test your adjustments. Setting Test Tone
to On turns the Test Tone on. Setting it to Off turns
it off.
Speaker Selection
Lets you select which speakers you want active,
either the TV's speakers or the home cinema's
speakers.
Audio Return Channel
Lets you direct the sound from the TV to the Home
Cinema speakers. Requires an HDMI connection
and an Audio Return Channel (ARC) compatible
TV.
If Audio Return Channel is set to on and you
are using an HDMI cable to connect the product
to the TV, digital optical input will not work.
If Audio Return Channel is set to Auto and you
are using an HDMI cable to connect the product
to the TV, ARC or digital optical input is selected
automatically.
Digital Output
Lets you set the Digital Output to match the
capabilities of the AV receiver you’ve connected to
the product. For more details, please refer to the
digital output selection table. (See page 39)
Dynamic Range Control
Lets you apply dynamic range control to Dolby
Digital, Dolby Digital Plus, and Dolby TrueHD audio.
Auto: Automatically controls the dynamic range
of Dolby TrueHD audio, based on information in
the Dolby TrueHD soundtrack. Also turns dynamic
range control off for Dolby Digital and Dolby Digital
Plus.
Off: Leaves the dynamic range uncompressed,
letting you hear the original sound.
On: Turns dynamic range control on for all three
Dolby formats. Quieter sounds are made louder
and the volume of loud sounds is reduced.
Downmixing Mode
Lets you select the multi-channel downmix method
that is compatible with your stereo system. You
can choose to have the product downmix to
Normal Stereo or to Surround Compatible.
Audio Sync
When the product is attached to a digital TV, lets
you adjust the audio delay so that the audio syncs
with the video. You can set the delay between 0
and 300 milliseconds.
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 17HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 17 2014-05-08  11:35:512014-05-08  11:35:51
18 - English
Settings
Network
Wired Network Settings
For more information about this function see page
19.
Network Test
Lets you test the Internet Protocol setup to see if it
is working correctly.
Network Status
Lets you check the current network and Internet
status.
Device Name
Lets you assign an identifying name to the product.
You use this name to identify the product when you
are connecting external devices (smart phones,
tablets, etc.) to it.
BD-Live Internet Connection
Lets you allow or prohibit an Internet connection
for the BD-Live service.
System
Initial Settings
Lets you re-run the Initial Settings procedure. (See
page 14)
Quick start
You can turn on the power quickly by decreasing
the boot time.
If this function is set to On, Standby power
consumption will be increased. (About 12W ~ 20W)
Anynet+ (HDMI-CEC)
Anynet+ is a convenient function that offers linked
operations with other Samsung products that have
the Anynet+ feature and lets you control those
products with one Samsung TV remote. To operate
this function, you must connect this product to an
Anynet+ Samsung TV using a HDMI cable.
BD Data Management
Lets you manage the contents you downloaded
through a Blu-ray disc that supports the BD-Live
service. You can view the information about the
USB device you are using for BD Live data storage
including the storage space. You can also delete
BD Live data and change the device.
DivX® Video On Demand
View DivX® VOD Registration Codes to purchase
and play DivX® VOD contents.
Language
Lets you select the language you prefer for the On-
Screen Menu, disc menu, etc.
The selected language will only appear if it is
supported on the disc.
Security
The default PIN is 0000. Enter the default PIN to
access the security function if you haven't created
your own PIN.
BD Parental Rating
Prevents playback of Blu-ray Discs with a rating
equal to or above a specific age rating unless you
enter the PIN.
DVD Parental Rating
Prevents playback of DVDs with a rating above a
specific numerical rating unless you enter the PIN.
Change PIN
Changes the 4-digit PIN used to access security
functions.
General
Time Zone
Lets you specify the time zone that is applicable to
your area.
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 18HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 18 2014-05-08  11:35:522014-05-08  11:35:52
19 - English
Settings
Support
Software Upgrade
For more information about this function see page
20.
Contact Samsung
Provides contact information for assistance with
your product.
Terms of Service Agreement
View the general disclaimer regarding third party
contents and services.
Reset
Reverts all settings to their defaults except for the
network. Requires that you enter your security PIN.
The default security PIN is 0000.
Network Setup
When you connect this product to a network, you
can use network based applications and functions
such as BD-LIVE and upgrade the product's software
through the network connection.
Configuring Your Network Connection
If you skipped network setup during the Initial Setup,
follow the instructions below to configure the home
cinema's network connection.
Before you begin, contact your ISP to find out if your
IP address is static or dynamic. If it is dynamic, we
recommend you use the automatic procedure below.
If it is static, you must use the manual procedure that
follows.
Before you begin, confirm that the product is
connected to your router with a network cable.
Automatic
To start the configuration process, follow these steps:
1. In the Home menu, select Settings, and then
press the
E
button.
2. Select Network, and then press the
E
button.
3. Select Wired Network Settings, and then press
the
E
button.
The Wired Network Settings screen appears.
4. Press the
+
button on the Internet Protocol
Setup menu.
Use
%
button to select Auto, and then press
the
E
button.
Settings
Display
Audio
Network
System
Language
Security
General
Support
0000
0
0000
0000
000
Wired Network Settings
Internet Protocol Setup : Auto
IP Address :
Subnet Mask :
Gateway :
DNS : Auto
DNS Server :
> Move " Select ' Return
5. The Network function acquires and fills in the
values for IP Address, Subnet Mask, etc.,
automatically.
6. After the Network function has acquired the
network values, press the
RETURN button.
7. Select Network Test, and then press
E
. The
home cinema validates the network connection.
When it is done, press the RETURN button.
Manual
If you have a static IP address or the Automatic
procedure does not work, you’ll need to set the Network
Settings values manually. You can get the Network
Settings from your Internet Service Provider (ISP).
Settings
Display
Audio
Network
System
Language
Security
General
Support
0000
255 255 255
0
0000
0000
Wired Network Settings
Internet Protocol Setup : Manual
IP Address :
Subnet Mask :
Gateway :
DNS : Manual
DNS Server :
> Move " Select ' Return
1. Follow the first four steps in the Automatic
procedure, but select Manual instead of Auto in
Step 4.
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 19HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 19 2014-05-08  11:35:542014-05-08  11:35:54
20 - English
Settings
2. Press the
button to go to the first entry field (IP
Address).
3. Use the number buttons on your remote to enter
numbers.
4. When done with each field, use the ► button to
move successively to the next field.
You can also use the other arrow buttons to
move up, down, and back.
5. Enter the IP Address, Subnet Mask, and
Gateway values.
6. Press the ▼ button to go to DNS.
7. Press the ▼ button to go to the first DNS entry
field. Enter the numbers as above.
8. Press the
RETURN button on your remote.
9. Select Network Test, and then press
E
.
When the test is completed, press the RETURN
button to exit to the previous screen.
10. Select Network Status, and then press
E
.
11. The Network Status screen appears.
The product verifies the network connection and
then connects to the network. When it is done,
highlight OK, and then press
E
.
Upgrading Software
The Software Upgrade menu allows you to upgrade
the product’s software for performance improvements
or additional services.
Never turn the product off or back on manually
during the update process.
The update is complete when the product turns
off after restarting. Press the
POWER button to
turn on the updated product for your use.
Samsung Electronics takes no legal
responsibility for product malfunction caused by
an unstable Internet connection or consumer
negligence during a software upgrade.
1. In the Home menu, select Settings, and then
press the
E
button.
2. Select Support, and then press the
E
button.
3. Select Software Upgrade, and then press the
E
button.
4. Select one of the following methods:
• By Online
• By USB
Auto Upgrade Notification
5. Press the
E
button.
Directions for each method begin below.
If you want to cancel the upgrade while the
upgrade software is downloading, press the
E
button.
By Online
Your product must be connected to the Internet to
use the By Online function. Remove all discs before
you begin.
1. Select By Online, and then press the
E
button. The Connecting to Server message
appears.
2. If an update is available, a popup message
appears asking if you want to upgrade. If you
select Yes, the product turns off automatically,
turns on, and then begins the upgrade.
3. The update progress popup appears. When
the update is completed, the product turns off
automatically again.
4. Press the
POWER button to turn on the
product.
By USB
1. Visit www.samsung.com.
2. Click SUPPORT on the top right of the page.
3. Enter the product's model number into the
search field. As you enter the model number, a
drop down will display products that match the
model number.
4. Left click your product's model number in the
drop down list.
5. On the page that appears, scroll down to and
then click Firmware Manuals & Downloads.
6. Click Firmware in the centre of the page.
7. Click the ZIP icon in the File column on the right
side of the page.
HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 20HT-H4500K_30HK_30K_50K_ZN-ENG-0508.indd 20 2014-05-08  11:35:572014-05-08  11:35:57
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136

Samsung HT-H4550K Manuel utilisateur

Catégorie
Lecteurs Blu-Ray
Taper
Manuel utilisateur

dans d''autres langues