red lion EL228 Guide de démarrage rapide
- Catégorie
- Les routeurs
- Taper
- Guide de démarrage rapide
EL228
Quick Start Guide
Note: This guide is for a typical installation. Refer to the user manuals on the supplied
CD or www.sixnet.com for full installation and management details.
All power, input and output (I/O) wiring must be in accordance with Class I, Division 2 wiring
methods and in accordance with the authority having jurisdiction. This equipment is Suitable for
Use in Class I, Division 2, Groups A, B, C and D or Non-Hazardous Locations Only.
WARNING – EXPLOSION HAZARD – SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2.
WARNING – EXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT WHILE THE CIRCUIT IS LIVE OR UNLESS THE AREA
IS KNOWN TO BE FREE OF IGNITABLE CONCENTRATIONS.
WARNING – EXPLOSION HAZARD – WHEN IN HAZARDOUS LOCATIONS, DISCONNECT POWER BEFORE REPLACING OR
WIRING UNITS.
WARNING – EXPLOSION HAZARD – IN HAZARDOUS OR POTENTIALLY HAZARDOUS LOCATIONS, DO NOT SEPARATE ANY
PART OF THE UNIT WHEN ENERGIZED. USE THE UNIT FOR INTERNAL CONNECTIONS ONLY.
WARNING – Exposure to some chemicals may degrade the sealing properties of materials used in the Sealed Relay
Device.
Tout pouvoir, le câblage d’entrée et de sortie (I/O) doivent être conformes aux méthodes de câblage
de Classe I, Division 2 et conformément à l’autorité compétente. Cet équipement est adapté pour
une utilisation en Classe1, Division 2, Groupes A, B, C et D ou endroits non-dangereux seulement.
AVERTISSEMENT – RISQUE D’EXPLOSION – LA SUBSTITUTION DE TOUT COMPOSANT PEUT NUIRE À LA CONFORMITÉ DE
CLASSE I, DIVISION 2.
AVERTISSEMENT – RISQUE D’EXPLOSION – NE DÉBRANCHEZ PAS L’ÉQUIPEMENT PENDANT QUE LE CIRCUIT EST DIRECT
OU À MOINS QUE L’ENVIRONNEMENT SOIT CONNU POUR ÊTRE LIBRE DE CONCENTRATIONS INFLAMMABLES.
WARNING – EXPLOSION HAZARD – LORSQUE DANS DES ENDROITS DANGEREUX, DÉBRANCHEZ LE CORDON
D'ALIMENTATION AVANT DE REMPLACER OU DE BRANCHER LES MODULES.
WARNING – EXPLOSION HAZARD – DANS LES ENDROITS DANGEREUX OU POTENTIELLEMENT DANGEREUX, NE PAS
SEPARER UNE PARTIE DE L'UNITE SOUS TENSION. SEULEMENT UTILISEZ L'APPAREIL POUR LES CONNEXIONS INTERNES.
WARNING – L'exposition à certains produits chimiques peut dégrader les propriétés d'étanchéité des matériaux utilisés
dans les relais étanche périphérique.
1. Carefully remove the switch and accessories from the shipping container and inspect
them for damage. Contact Red Lion immediately if any damage is discovered.
2. Install the mounting brackets using the #10-32 screws provided. There should be four
per bracket. The same brackets may be used
for both standard and reverse mounted
configurations.
3. Install the switch into your rack using standard
rack hardware which is not included with the
switch. Alternatively, you can skip the rack
installation if you would like to configure the
switch beforehand.
4. Plug in your SFP transceivers as desired.
5. Connect a power source to the switch as appropriate
for the model you have. Please check the part number
and make sure you are applying the correct power.
IMPORTANT NOTE: Make sure to turn off your power
before making any connections to the switch. Make sure you are applying the correct
power to the correct screws. Follow all local, national or regulatory rules that apply.
6. Turn on the power to the switch. The Pwr 1 and/or Pwr 2 LED should be on solid.
7. Plug in your Ethernet cables and the switch will immediately start to pass data.
8. Now you may configure the switch for more advanced operations. To manage the
switch there are two primary interface methods: CLI (Command Line Interface) and
Web UI (User Interface). See the back to start managing the switch.
Accessing your switch over the network using the default IP address:
1. Connect the switch directly to your PC’s Ethernet port using any Ethernet patch cable.
The switch’s default IP and subnet are 192.168.0.1 and 255.255.255.0.
2. On your PC, go to Control Panel - Network Connections and access the properties for
your LAN’s Internet Protocol (TCP/IP). Select “Use this IP address” and set the IP &
subnet to 192.168.0.100 & 255.255.255.0. Close and reboot if prompted.
3. Run a web browser such as Internet Explorer and type 192.168.0.1 into the address bar
and hit the enter key. Use “admin” for both the username and password to access the
web interface.
4. In the IP Configuration screen, enter your desired IP and subnet, or enable DHCP. Click
on Apply to save these new settings to the switch.
5. To make this change permanent you must go to the Copy screen under File
Management and select “running-config to startup-config” and click on Apply
6. Repeat step 2 to return your PC to its original IP address and subnet mask.
EL228 Quick Start Guide Revision 16-Dec-13
Now you can access your switch using the new IP address! Just type it into the web browser.
Refer to the management guide or online help for details on further configuring the switch.
Setting a new IP via the CLI (Command Line Interface):
1. Open your terminal program of choice (eg. Hyperterminal) and configure your serial port
for 9600 8/N/1
2. At the main screen press <Enter> to display the login prompt
3. Login to the switch; the default username & password are both admin
4. To enter the configuration menu, type config and press <Enter>
5. To access the interface-configuration mode, type interface vlan 1 and press <Enter>
6. Type ip address followed by your desired IP address and netmask and press <Enter>
7. To return to the global configuration mode prompt, type exit and press <Enter>
8. To set the IP address of the default gateway for the network to which the switch
belongs, type ip default-gateway followed by the IP address and press <Enter>
9. To leave the global configuration mode, type exit and press <Enter>
10. To save the changes, type copy running-config startup-config
11. Define the startup filename or press <Enter> to accept the default
12. You should now be able to access the switch at the IP address you configured.
Example CLI session:
-
1
-
2
-
3
red lion EL228 Guide de démarrage rapide
- Catégorie
- Les routeurs
- Taper
- Guide de démarrage rapide
dans d''autres langues
- English: red lion EL228 Quick start guide