Maytag MER5751BAB - 30 Inch Electric Range Mode d'emploi

Marque: Maytag

Modèle: MER5751BAB - 30 Inch Electric Range

Catégorie: Cuisinières

Taper: Mode d'emploi

Safety.......................................... 1-3

Surface Cooking ...................... 4-7

Surface Controls

Smoothtop Surface

Oven Cooking ......................... 8-16

Baking

Cook & Hold

Delay Bake

Keep Warm

Broiling

Oven Racks

Table of Contents

Care & Cleaning ...................17-20

Self-Clean Oven

Cleaning Procedures

Maintenance .........................21-22

Oven Window

Oven Light

Troubleshooting ...................22-23

Warranty & Service.................... 25

Guide d’utilisation et

d’entretien ................................... 26

Guía de Uso y Cuidado ............. 54

Electric Range -

Smoothtop

Use and Care Guide

Form No. A/01/08 Part No. 8113P730-60

Installer: Please leave this guide with this appliance.

Consumer: Please read and keep this guide for future

reference. Keep sales receipt and/or canceled check as proof

of purchase.

Model Number __________________________________

Serial Number __________________________________

Date of Purchase ________________________________

If you have questions, call:

Customer Assistance

1-800-688-9900 USA

1-800-688-2002 Canada

1-800-688-2080 (U.S. TTY for hearing or speech impaired)

(Mon.-Fri., 8 am-8 pm Eastern Time)

Internet: http://www.maytag.com

In our continuing effort to improve the quality and performance

of our cooking products, it may be necessary to make changes

to the appliance without revising this guide.

For service information, see page 25.

Warning and Important Safety Instructions appearing in this

guide are not meant to cover all possible conditions and

situations that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operating

the appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words, Labels

WARNING – Hazards or unsafe practices which COULD

result in severe personal injury or death.

CAUTION – Hazards or unsafe practices which COULD

result in minor personal injury.

WARNING

CAUTION

• ALL RANGES CAN TIP AND

CAUSE INJURIES TO PERSONS

• INSTALL ANTI-TIP DEVICE

PACKED WITH RANGE

• FOLLOW ALL INSTALLATION

INSTRUCTIONS

WARNING: To reduce risk of

tipping of the appliance from

abnormal usage or by excessive

loading of the oven door, the appliance must

be secured by a properly installed anti-tip

device.

Read and follow all instructions before using this

appliance to prevent the potential risk of fire, electric

shock, personal injury or damage to the appliance as a

result of improper usage of the appliance. Use appliance

only for its intended purpose as described in this guide.

To ensure proper and safe operation: Appliance

must be properly installed and grounded by a qualified

technician. Do not attempt to adjust, repair, service, or

To check if device is properly installed, look underneath

range with a flashlight to make sure one of the rear leveling

legs is properly engaged in the bracket slot. The anti-tip

device secures the rear leveling leg to the floor when

properly engaged. You should check this anytime the

range has been moved.

WARNING

Important Safety

Instructions

To Prevent Fire or Smoke

Damage

Be sure all packing materials are removed from the

appliance before operating it.

Keep area around appliance clear and free from

combustible materials. Flammable materials should not be

stored in an oven.

Many plastics are vulnerable to heat. Keep plastics away

from parts of the appliance that may become warm or hot.

To prevent grease fires, do not let cooking grease or other

flammable materials accumulate in or near the appliance.

replace any part of your appliance unless it is specifically

recommended in this guide. All other servicing should be

referred to a qualified servicer.

Always disconnect power to appliance before servicing.

In Case of Fire

Use dry chemical or foam-type extinguisher or baking soda

to smother fire or flame. Never use water on a grease fire.

1. Turn off appliance to avoid spreading the flame.

2. NEVER pick up or move a flaming pan.

3. Smother oven fire or flame by closing the oven door.

Important Safety Instructions

NEVER leave children alone or unsupervised near the

appliance when it is in use or is still hot. Children should

never be allowed to sit or stand on any part of the appliance

as they could be injured or burned.

Children must be taught that the appliance and utensils in it

can be hot. Let hot utensils cool in a safe place, out of reach

of small children. Children should be taught that an appli-

ance is not a toy. Children should not be allowed to play with

controls or other parts of the appliance.

About Your Appliance

Cooking Safety

Never heat an unopened food container in the oven. Pressure

build-up may cause container to burst resulting in serious

personal injury or damage to the appliance.

Use dry, sturdy potholders. Damp potholders may cause burns

from steam. Dish towels or other substitutes should never be

used as potholders because they can trail across hot elements

and ignite or get caught on appliance parts.

Wear proper apparel. Loose fitting or long hanging-sleeved

apparel should not be worn while cooking. Clothing may

ignite and cause burns if garment comes in contact with

heating elements.

Always place oven racks in the desired positions while oven is

cool. Slide oven rack out to add or remove food, using dry,

sturdy potholders. Always avoid reaching into the oven to add

or remove food. If a rack must be moved while hot, use a dry

potholder. Do not let potholder contact hot element in oven.

Use racks only in the oven in which they were shipped/

purchased.

Use care when opening the oven door. Let hot air or steam

escape before removing or replacing food.

PREPARED FOOD WARNING: Follow food manufacturer’s

instructions. If a plastic frozen food container and/or its cover

distorts, warps, or is otherwise damaged during cooking,

immediately discard the food and its container. The food could

be contaminated.

Do not allow aluminum foil or meat probe to contact heating

element.

Always turn off all controls when cooking is completed.

CAUTION

NEVER use an appliance as a step to reach cabinets

above. Misuse of appliance door, such as stepping,

leaning or sitting on the door, may result in possible

tipping of the appliance, breakage of door, and serious

injuries.

To prevent potential hazard to the user and damage to the

appliance, do not use appliance as a space heater to heat or

warm a room. Also, do not use the oven as a storage area for

food or cooking utensils.

Do not obstruct the flow of air by blocking the oven vent.

DO NOT TOUCH HEATING ELEMENTS OR INTERIOR

SURFACES OF OVEN. Heating elements may be hot even

though they are dark in color. Interior surfaces of any oven

become hot enough to cause burns. During and after use, do

not touch, or let clothing or other flammable materials contact

heating elements or interior surfaces of oven until they have

had sufficient time to cool. Other surfaces of the appliance

may become hot enough to cause burns – among these

surfaces are: oven vent opening, surface near this opening,

oven door, and window of oven door.

Do not touch a hot oven light bulb with a damp cloth as the

bulb could break. Should the bulb break, disconnect power to

the appliance before removing bulb to avoid electrical shock.

NEVER use aluminum foil to cover an oven rack or oven

bottom. Misuse could result in risk of electric shock, fire, or

damage to the appliance. Use foil only as directed in this

guide.

CAUTION

NEVER store items of interest to children in cabinets above

an appliance. Children climbing on the appliance or on the

appliance door to reach items could be seriously injured.

Child Safety

Utensil Safety

Follow the manufacturer’s directions when using oven cooking

bags.

This appliance has been tested for safe performance using

conventional cookware. Do not use any devices or accesso-

ries that are not specifically recommended in this manual. Do

not use stove top grills or add-on oven convection systems.

The use of devices or accessories that are not expressly

recommended in this manual can create serious safety

hazards, result in performance problems, and reduce the life

of the components of this appliance.

Be sure utensil is large enough to properly contain food and

avoid boilovers. Pan size is particularly important in deep fat

frying. Be sure pan will accommodate the volume of food

that is to be added as well as the bubble action of fat.

Important Safety Instructions

or cloth is used to wipe spills on a hot surface. Some clean-

ers can produce noxious fumes if applied to a hot surface.

Clean only parts listed in this guide.

Self-Clean Oven

CAUTION

Before self-cleaning the oven, remove the oven

racks, broiler pan, food and any other utensils. Wipe

spillovers to prevent excessive smoke and flare-ups.

Do not clean door gasket. The door gasket is essential for a

good seal. Care should be taken not to rub, damage, or

move the gasket.

Do not use oven cleaners or oven liners of any kind in or

around any part of the self-clean oven.

It is normal for the cooktop of the range to become hot

during a self-clean cycle. Therefore, touching the cooktop

during a clean cycle should be avoided.

Important Safety Notice and

Warning

The California Safe Drinking Water and Toxic

Enforcement Act of 1986 (Proposition 65) requires the

Governor of California to publish a list of substances known

to the State of California to cause cancer or reproductive

harm, and requires businesses to warn customers of poten-

tial exposures to such substances.

Users of this appliance are hereby warned that when the

oven is engaged in the self-clean cycle, there may be some

low-level exposure to some of the listed substances, includ-

ing carbon monoxide. Exposure to these substances can be

minimized by properly venting the oven to the outdoors by

opening the windows and/or door in the room where the

appliance is located during the self-clean cycle.

IMPORTANT NOTICE REGARDING PET BIRDS: Never

keep pet birds in the kitchen or in rooms where the fumes

from the kitchen could reach. Birds have a very sensitive

respiratory system. Fumes released during an oven self-

cleaning cycle may be harmful or fatal to birds. Fumes

released due to overheated cooking oil, fat, margarine and

overheated non-stick cookware may be equally harmful.

Never let a pan boil dry as this could damage the utensil

and the appliance.

If pan is smaller than element, a portion of the element will

be exposed to direct contact and could ignite clothing or

potholder.

Only certain types of glass, glass/ceramic, ceramic,

earthenware, or other glazed utensils are suitable for

cooktop or oven service without breaking due to the sudden

change in temperature. Follow utensil manufacturer’s

instructions when using glass.

Turn pan handle toward center of cooktop, not out into the

room or over another surface element. This reduces the risk

of burns, ignition of flammable materials, or spillage if pan is

accidently bumped or reached by small children.

Cooktop

NEVER leave surface units unattended especially when using

high heat. An unattended boilover could cause smoking and

a greasy spillover can cause a fire.

This appliance is equipped with different size surface ele-

ments. Select pans with flat bottoms large enough to cover

element. Fitting pan size to element will improve cooking

efficiency.

GLASS-CERAMIC SURFACE: NEVER cook on broken

cooktop. If cooktop should break, cleaning solutions and

spillovers may penetrate the broken cooktop and create a risk

of electric shock. Contact a qualified technician immediately.

Deep Fat Fryers

Use extreme caution when moving the grease pan or dispos-

ing of hot grease. Allow grease to cool before attempting to

move pan.

Ventilating Hoods

Clean range hood and filters frequently to prevent grease or

other flammable materials from accumulating on hood or

filter and to avoid grease fires.

When flaming foods under the hood, turn the fan on.

Cleaning Safety

Clean cooktop with caution. Turn off all controls and wait for

appliance parts to cool before touching or cleaning. Clean

with caution. Use care to avoid steam burns if a wet sponge

Save These Instructions for Future Reference

Surface Cooking

Surface Controls

Use to turn on the surface elements. An infinite choice of

heat settings is available from Low to High. The knobs can

be set on or between any of the settings.

Setting the Controls

1. Place pan on surface element.

2. Push in and turn the knob in either direction to the desired

heat setting.

• The control panel is marked to identify

which element the knob controls. For

example, the graphic at right indicates left front element.

3. There is an element indicator light on the control panel.

When any surface control knob is turned on, the light will

turn on. The light will turn off when all the surface ele-

ments are turned off.

4. After cooking, turn knob to OFF. Remove pan.

Suggested Heat Settings

The size and type of cookware, type and amount of food

being heated, and wattage of individual elements will

determine where to set the knob for cooking

operations. Some elements have a predetermined simmer and

melt setting that will require only minor adjustment up or

down depending on the food being prepared. The other

elements have settings printed around the knobs that are also

unique to those elements. Adjust the heat settings to the

numbers that give the desired cooking results. For

information on cookware and other factors affecting heat

settings, refer to Cookware Recommendations on page 7. The

following descriptions will aid in choosing the settings that

will give optimum results.

Hold or Warm: Food maintains a temperature above 140°F

without continuing to cook. Food is initially hot and then heat

is reduced. Never use a hold or warm setting to reheat cold

food.

Simmer: Food forms bubbles that barely break the

surface. Foods are between 185°F and 200°F. A simmer

setting can also be used to steam or poach foods or continue

cooking covered foods.

Slow Boil: Food forms bubbles at a moderate pace. A slow

boil setting can also be used for most frying and for

maintaining the cooking of large amounts of liquids.

Boil: Liquid forms bubbles at a rapid pace. A fast boil setting

can also be used to brown meat, stir fry, sauté, and heat oil

for frying before turning to a lower setting. The highest 3 or 4

settings on the knob are used for these cooking

operations. The highest setting is always used to bring water

to a boil. Some elements offer an even higher speed for

boiling liquids.

Dual Element (select models)

The cooking surface has a dual element

located at the left front of the

smoothtop. This allows you to change

the size of the element.

The small element is operated on the left

side of the knob control. To operate the

entire element, use the right side of the knob control. The

control for both element sizes can be set anywhere between

Low and High.

Front

Flex-Choice

Element (select models)

The Flex-Choice

element is a fully functioning

element that provides an ultra low Melt

heat setting for melting chocolate and

butter. It is located in the left rear position

The Melt setting is located between

2 and OFF. Heat settings outside of

this area function as a normal element,

with 2 (Low) to High settings.

Note: When using the normal settings for preparing foods,

it may take a few minutes for the cooking area to cool to

the Melt heat setting.

Notes:

• Never warm food for longer than one hour (eggs for 30

minutes), as food quality may deteriorate.

• Do not heat cold food on the Warming Center.

• Heat settings will vary depending on type and amount of

food. Always hold food at proper food temperatures. USDA

recommends food temperatures between 140°-170° F.

Warming Center

Use the Warming Center to keep hot cooked foods warm,

such as vegetables and gravies.

Setting the Control:

1. Push in and turn the knob. Warming

temperatures are approximate and are

indicated on the control as Low, 2-10

and High. However, the control can be

set to any position between Low and

High.

2. When done, turn the control to OFF and

remove food. The Hot Surface indicator light will go off

when the Warming Center surface has cooled.

Smoothtop Surface Notes:

• Cooktop may emit light smoke and odor the first few

times the cooktop is used. This is normal.

• Smoothtop cooktops retain heat for a period of time

after the element is turned off. Turn the elements off

a few minutes before food is completely cooked and use

the retained heat to complete cooking. When the hot

surface light turns off, the cooking area will be cool

enough to touch. Because of the way they retain heat, the

smoothtop elements will not respond to changes in

settings as quickly as coil elements.

• In the event of a potential boilover, remove the pan from

the cooking surface.

• Never attempt to lift the cooktop.

• The smoothtop surface may appear discolored when it is

hot. This is normal and will disappear when the surface

cools.

Smoothtop Surface

Cooking Areas

The cooking areas on your range are identified by permanent

circles on the smoothtop surface. For most efficient cooking,

fit the pan size to the element size.

Pans should not extend more than 1-inch beyond the

cooking area.

Warming Center Suggested Settings

Setting Type of food

Low - 2 Breads/Pastries Gravies

Casseroles Eggs

2 - Medium Sauces Soups (Cream)

Stews Vegetables

Meats

Medium - High Fried Foods Hot Beverages

Soups (Liquid)

Warming Center Notes:

• Use only cookware and dishes recommended as safe for

oven and cooktop use.

• Always use oven mitts when removing food from the

Warming Center as utensils will be hot.

• All foods should be covered with a lid or aluminum foil to

maintain food quality.

• When warming pastries and breads the cover should have

an opening to allow moisture to escape.

• Do not use plastic wrap to cover foods. Plastic may melt

on to the surface and be very difficult to clean.

• Be very careful not to allow aluminum foil to touch the

cooktop. If foil melts, do not use the cooktop. Call an

authorized Maytag servicer.

BEFORE COOKING

• Always place a pan on the surface unit before you turn it

on. To prevent damage to range, never operate surface

unit without a pan in place.

• NEVER use the cooktop as a storage area for food or

cookware.

DURING COOKING

• Be sure you know which knob controls which surface

unit. Make sure you turned on the correct surface unit.

• Begin cooking on a higher heat setting then reduce to a

lower setting to complete the operation. Never use a

high heat setting for extended cooking.

• NEVER allow a pan to boil dry. This could damage the

pan and the appliance.

• NEVER touch cooktop until it has cooled. Expect some

parts of the cooktop, especially around the surface units,

to become warm or hot during cooking. Use potholders

to protect hands.

CAUTION

AFTER COOKING

• Make sure surface unit is turned off.

• Clean up messy spills as soon as possible.

OTHER TIPS

• If cabinet storage is provided directly above cooking

surface, limit it to items that are infrequently used and can

be safely stored in an area subjected to heat. Tempera-

tures may be unsafe for items such as volatile liquids,

cleaners or aerosol sprays.

• NEVER leave any items, especially plastic items, on the

cooktop. The hot air from the vent may ignite flammable

items, melt or soften plastics, or increase pressure in

closed containers causing them to burst.

• NEVER allow aluminum foil, meat probes or any other

metal object, other than a pan on a surface element, to

contact heating elements.

• NEVER store heavy items above the cooktop that could fall

and damage it.

Surface Cooking

cont.

Surface Cooking

When a control is turned on, a glow can be seen through the

smoothtop surface. The element will cycle on and off to

maintain the preset heat setting, even on Hi.

For more information on cookware, refer to Cookware

Recommendations on page 7 and “Cooking Made Simple”

booklet included with your range.

WARMING CENTER

DUAL ELEMENT

(SELECT MODELS)

FLEX-CHOICE

ELEMENT

SINGLE

ELEMENT

Tips to Protect the

Smoothtop Surface

Cleaning (see page 19 for more information)

• Before first use, clean the cooktop.

• Clean your cooktop daily or after each use. This will keep

your cooktop looking good and can prevent damage.

• If a spillover occurs while cooking, immediately clean the

spill from the cooking area while it is hot to prevent a tough

cleaning chore later. Using extreme care, wipe spill with a

clean dry towel.

• Do not allow spills to remain on the cooking area or the

cooktop trim for a long period of time.

• Never use abrasive cleansing powders or scouring pads

which will scratch the cooktop.

• Never use chlorine bleach, ammonia or other cleansers not

specifically recommended for use on glass-ceramic.

Hot Surface Light

The Hot Surface indicator light is located on

the control panel. The light will be illuminated

when any cooking area is hot. It will remain

on, even after the control is turned off, until the area has

cooled.

To Prevent Marks and Scratches

• Do not use glass pans. They may scratch the surface.

• Never place a trivet or wok ring between the surface and

pan. These items can mark or etch the top.

• Do not slide aluminum pans across a hot surface. The pans

may leave marks which need to be removed promptly. (See

Cleaning, page 19.)

• Make sure the surface and the pan bottom are clean before

turning on to prevent scratches.

• To prevent scratching or damage to the glass-ceramic top,

do not leave sugar, salt or fats on the cooking area. Wipe

the cooktop surface with a clean cloth or paper towel

before using.

• Never slide heavy metal pans across the surface since

these may scratch.

To Prevent Stains

• Never use a soiled dish cloth or sponge to clean the

cooktop surface. A film will remain which may cause stains

on the cooking surface after the area is heated.

• Continuously cooking on a soiled surface may/will result in

a permanent stain.

To Prevent Other Damage

• Do not allow plastic, sugar or foods with high sugar content

to melt onto the hot cooktop. Should this happen, clean

immediately. (See Cleaning, page 19.)

• Never let a pan boil dry as this will damage the surface and

pan.

• Never use cooktop as a work surface or cutting board.

• Never cook food directly on the surface.

• Do not use a small pan on a large element. Not only does

this waste energy, but it can also result in spillovers burning

onto the cooking area which requires extra cleaning.

• Do not use non-flat specialty items that are oversized or

uneven such as round bottom woks, rippled bottom and/or

oversized canners and griddles.

• Do not use foil or foil-type containers. Foil may melt onto

the glass. If metal melts on the cooktop, do not use. Call an

authorized servicer.

Surface Cooking

Cookware Recommendations

Select Avoid

Flat, smooth-bottom Pans with grooved or warped bottoms.

pans. Pans with uneven bottoms do not cook

efficiently and sometimes may not

boil liquid.

Heavy-gauge pans. Very thin-gauge metal or glass pans.

Pans that are the Pans smaller or larger than the

same size as the element by 1 inch.

element.

Secure handles. Cookware with loose or broken handles.

Heavy handles that tilt the pan.

Tight-fitting lids. Loose-fitting lids.

Flat bottom woks. Woks with a ring-stand bottom.

Using the right cookware can prevent many problems, such

as food taking longer to cook or achieving inconsistent

results. Proper pans will reduce cooking times, use less

energy, and cook food more evenly.

Flat Pan Tests

See if your pans are flat.

The Ruler Test:

1. Place a ruler across the bottom of the pan.

2. Hold it up to the light.

3. Little or no light should be visible under the ruler.

The Bubble Test:

1. Put 1 inch of water in the pan. Place on cooktop and turn

control to High.

2. Watch the formation of the bubbles as the water heats.

Uniform bubbles mean good performance, and uneven

bubbles indicate hot spots and uneven cooking.

Canning and Oversize

Cookware

All canners and large pots must have flat bottoms and

must be made from heavy-gauge materials. This is critical

on smoothtop surfaces. The base must not be more than

1 inch larger than the element.

When canners and pots do not meet these standards, cooking

times may be longer, and cooktops may be damaged.

Some canners are designed with smaller bases for use on

smoothtop surfaces.

When canning, use the High heat setting only until the

water comes to a boil or pressure is reached in the canner.

Reduce to the lowest heat setting that maintains the boil or

pressure. If the heat is not turned down, the cooktop may be

damaged.

Oven Cooking

Control Panel

The control panel is designed for ease in programming. The display window on the control shows time of day, timer and oven functions.

Control panel shown includes model specific features. (Styling may vary depending on model.)

Using the Touchpads

• Press the desired pad.

• Press the More+ or Less- pad to enter time or temperature.

• A beep will sound when any pad is touched.

• A double beep will sound if a programming error occurs.

A Broil Use for broiling and top browning.

B Bake Use for baking and roasting.

C More+ or Enters or changes time, oven

Less- temperature. Sets HI or LO broil.

D Timer Sets Timer.

E Cook & Hold Bakes for a preset time, then holds food

warm for 1 hour.

F Clean Use to set self-clean cycle.

G Delay Programs the oven to start baking at

a later time.

H Clock Use to set time-of-day clock.

I Keep Warm Use to keep cooked food warm in oven.

J CANCEL Cancels all operations except Timer

and Clock.

A B C D

E F G H I J

Note: Four seconds after pressing the More+ or Less-

pad, the time or temperature will automatically be entered.

If more than 30 seconds elapse between touching a

function pad and the More+ or Less- pad, the function will

be canceled and the display will return to the previous

display.

Clock

The clock can be set to display time in a 12-hour or 24-hour

format. The clock is set at the factory for the 12-hour format.

To change the clock to 24-hour format:

1. Press and hold the CANCEL and Delay

pads for three seconds.

2. Press the More+ or Less - pad to select

12 or 24 hour.

3. Set the time of day following the

directions below.

To set the Clock:

1. Press the Clock pad.

• Time of day and the colon flash in the

display.

2. Press the More+ or Less- pad to set the

time of day.

• Colon continues flashing.

3. Press the Clock pad again or wait four

seconds.

When electrical power is supplied or after a power interrup-

tion, the last clock time before power was interrupted will

flash.

To recall the time of day when another time function is

showing, press the Clock pad.

Clock time cannot be changed when the oven has been

programmed for cook or clean Delay or Cook & Hold.

Oven Cooking

Timer

The timer can be set from one minute (00:01) up to 99 hours

and 59 minutes (99:59).

The timer can be used independently of any other oven

activity. It can also be set while another oven function is

operating.

The Timer does not control the oven. It only controls a

beeper.

To set the Timer:

1. Press the Timer pad.

• 0:00 lights in the display.

• The colon flashes in the display.

2. Press the More+ or Less- pad until the

correct time appears in the display.

• The colon will continue to flash.

3. Press Timer pad again or wait four seconds.

• The colon continues flashing and the time begins

counting down.

• The last minute of the timer countdown will be displayed

as seconds.

4. At the end of the set time, one long beep will sound.

To cancel the Timer:

1. Press and hold the Timer pad for three seconds.

2. Press the Timer pad and set the time to 00:00.

Locking the Control

The touchpad controls can be locked for safety, cleaning, or

to prevent unwanted use. They will not function when locked.

If the oven is currently in use, the controls cannot be locked.

The current time of day will remain in the display when the

controls are locked.

To lock:

Press and hold the CANCEL and Cook &

Hold pads for three seconds.

• LOCK flashes in the display.

To unlock:

Press and hold the CANCEL and Cook &

Hold pads for three seconds.

• LOCK disappears from the display.

Fault Codes

BAKE or LOCK may flash rapidly in the display to alert you if

there is an error or a problem. If BAKE or LOCK flash in the

display, press CANCEL pad. If BAKE or LOCK continue to

flash, disconnect power to the appliance. Wait a few minutes,

and then reconnect power. If the flashing still continues,

disconnect power to the appliance and call an authorized

servicer.

To cancel the Clock display:

If you do not want the time of day to display:

Press and hold the CANCEL and Clock

pads for three seconds. The time of day

will disappear from the display

When the clock display is canceled, press

the Clock pad to briefly display the time

of day.

To restore the Clock display:

Press and hold the CANCEL and Clock pads for three sec-

onds. The time of day will reappear in the display.

Oven Cooking

Baking Notes:

• To change oven temperature during cooking, press

the Bake pad, then press the More+ or Less- pad until

the desired temperature is displayed.

• To change oven temperature during preheat, press

the Bake pad twice, then press the More+ or Less- pad

until the desired temperature is displayed.

• If you forget to turn off the oven, it will automatically turn

off at the end of 12 hours. If you wish to deactivate this

feature, see page 13.

Baking

To set Bake:

1. Press the Bake pad.

• “BAKE” will flash.

• 000 will light in the display.

2. Select the oven temperature. The oven tempera-

ture can be set from 170° to 550°. Press or press

and hold the More+ or Less- pads.

• 350° will light when either pad is first pressed.

• Press the More+ pad to increase the temperature.

• Press the Less- pad to decrease the temperature.

3. Press Bake pad again or wait four seconds.

• BAKE will stop flashing and light in the display.

• 100° or the actual oven temperature will display. The

temperature will rise in 5° increments until the preset

temperature is reached.

4. Allow the oven to preheat for 8-15 minutes.

• When the set oven temperature is reached, one long

beep will sound.

• To recall the set temperature during preheat, press the

Bake pad.

5. Place food in center of oven, allowing a minimum of two

inches between utensil and oven walls.

6. Check cooking progress. Cook longer if needed.

7. When cooking is finished, press CANCEL.

8. Remove food from the oven.

Cook & Hold

Cook & Hold allows you to bake for a preset amount of time,

followed by a one-hour Keep Warm cycle.

To set Cook & Hold:

1. Press the Cook & Hold pad.

• “BAKE” and “HOLD” flash.

• 000 lights in the display.

2. Select the oven temperature. The oven tempera-

ture can be set from 170° to 550°. Press or press

and hold the More+ or Less- pad.

• Press the More+ pad to increase the temperature.

• Press the Less- pad to decrease the temperature.

3. Press Cook & Hold again OR wait four seconds.

• “HOLD” flashes.

• 00:00 flashes in the display.

4. Enter the amount of time you want to bake by pressing the

More+ or Less- pad. Bake time can be set from ten

minutes (00:10) to 11 hours, 59 minutes (11:59).

• “BAKE” and “HOLD” light in the display.

• The baking time will light in the display.

• The baking time will start counting down.

When the cooking time has elapsed:

• Four beeps will sound.

• “BAKE” will turn off.

• “HOLD” and “WARM” will light.

• 170° will display.

After one hour in HOLD WARM:

• “End” will display.

• The time of day reappears in the display.

To cancel Cook & Hold at any time:

Press the CANCEL pad. Remove food from oven.

Baking Differences Between Your Old

and New Oven

It is normal to notice some baking time differences between a

new oven and an old one. See “Adjusting the Oven Temperature”

on page 13.

Oven Cooking

CAUTION

Do not use delayed baking for highly perishable foods such

as dairy products, pork, poultry, or seafood.

When using Delay, the oven begins to cook later in the day.

Set the amount of time that you want to delay before the oven

turns on and how long you want to cook. The oven begins to

heat at the selected time and cooks for the specified length of

time, then keeps food warm for up to one hour.

Delay time can be set from 10 minutes (00:10) to 11 hours, 59

minutes (11:59).

To set a Delayed Baking cycle:

1. Press the Delay pad.

• “DELAY” flashes.

• 00:00 flashes in the display.

2. Press the More+ or Less- pad to set the

delay time.

While “DELAY” is still flashing:

3. Press the Cook & Hold pad.

• 000 lights in the display.

• “BAKE” and “HOLD” flash.

4. Press More+ pad to set the baking temperature.

• 00:00 and “HOLD” flash.

• “BAKE” stays lit.

5. Press More+ pad to set the baking time.

• The Delay time, “DELAY”, “BAKE” and “HOLD” light in

the display.

Notes:

• Do not use delayed baking for items that require a

preheated oven, such as cakes, cookies, and breads.

• Do not use delayed baking if oven is already hot.

Delay Bake

When the Delay time has expired:

• “DELAY” will turn off.

• Baking time is displayed.

• “BAKE” and “HOLD” are displayed.

To set a Delay when Cook & Hold has already

been programmed:

1. Press the Delay pad.

• “DELAY” flashes.

• 00:00 appears in the display.

2. Press the More+ or Less- pad to set the

delay time.

• After four seconds, “DELAY” will

stay lit to remind you that a delayed

cooking cycle has been set.

When the Delay time has expired and the oven

starts:

• The baking time will be displayed.

• “DELAY” will turn off.

• “BAKE” and “HOLD” will remain lit.

To cancel:

Press the CANCEL pad.

• All timed and untimed cooking functions will be

canceled.

• The time of day will reappear in the display.

Oven Cooking

Keep Warm Notes:

• For optimal food quality, oven cooked foods should be kept

warm for no longer than 1 to 2 hours.

• To keep foods from drying, cover loosely with foil or a lid.

• To warm dinner rolls:

- cover rolls loosely with foil and place in oven.

- press Keep Warm and More+ pads to set 170° F.

- warm for 12-15 minutes.

• To warm plates:

- place 2 stacks of up to four plates each in the oven.

- press Keep Warm and More+ pads to set 170° F.

- warm for five minutes, turn off the oven and leave plates

in the oven for 15 minutes more.

- use only oven-safe plates, check with the manufacturer.

- do not set warm dishes on a cold surface as rapid

temperature changes could cause crazing or breakage.

Keep Warm

For safely keeping foods warm or for warming breads and

plates.

To set Keep Warm:

1. Press the Keep Warm pad.

• “WARM” flashes.

• 000 appears in the display.

2. Select the Keep Warm temperature. The Keep

Warm temperature can be set from 145° to

190°. Press or press and hold the More+ or

Less- pad.

• 170° will light when either pad is first pressed.

• Press the More+ pad to increase the temperature.

• Press the Less- pad to decrease the temperature.

“WARM” and the temperature will be displayed while Keep

Warm is active.

To cancel Keep Warm:

1. Press the CANCEL pad.

2. Remove food from the oven.

Oven Cooking

Sabbath Mode Notes:

• Sabbath Mode can be turned on at any time with or

without the oven on.

• Sabbath Mode cannot be turned on if the touchpads are

locked out or when the door is locked.

• If the oven is baking when Sabbath Mode is set, “BAKE”

will go out at the end of the baking cycle. There will be

no audible beeps.

Automatic Shut-Off/Sabbath

Mode

The oven will automatically turn off after 12 hours if you

accidentally leave it on. This safety feature can be turned off.

To cancel the 12-hour shut-off and run the

oven continuously for 72 hours:

1. Set the oven to bake (see page 10).

2. Press and hold the Clock pad for five seconds.

• SAb will be displayed and flash for five seconds.

• SAb will then be displayed continuously until turned off

or until the 72-hour time limit is reached.

• “BAKE” will also be displayed if a bake cycle is in use

while the oven is in Sabbath Mode.

All other functions EXCEPT BAKE (Timer, Keep Warm,

Clean, etc.) are locked out during the Sabbath Mode.

To cancel Bake when in Sabbath Mode:

Press CANCEL.

• “BAKE” will turn off in the display.

• No beeps will sound.

To cancel the Sabbath Mode:

1. Press the Clock pad for five seconds.

2. After 72 hours, the Sabbath Mode will end.

• SAb will flash for five seconds.

• The time of day will return to the display.

Adjusting the Oven Temperature

Oven temperatures are carefully tested for accuracy at the

factory. It is normal to notice some baking or browning

differences between a new oven and an old one. As ranges

get older, the oven temperature can shift.

You may adjust the oven temperature if you think the oven is

not baking or browning correctly. To decide how much to

change the temperature, set the temperature 25° higher or

lower than your recipe recommends, then bake. The results

of the “test” should give you an idea of how much to adjust

the temperature.

To adjust the oven temperature:

1. Press Bake.

2. Enter 550° by pressing the More+ pad.

3. Press and hold the Bake pad for several

seconds or until 0° appears in the display.

If the oven temperature was previously adjusted, the

change will be displayed. For example, if the oven tem-

perature was reduced by 15° the display will show “-15°”.

4. Press the More+ or Less- pad to adjust the temperature.

Each time a pad is pressed, the temperature changes by

5°. The oven temperature can be increased or decreased

by 5° to 35°.

5. The time of day will automatically reappear in the display.

You do not need to readjust the oven temperature if there

is a power failure or interruption. Broiling and cleaning

temperatures cannot be adjusted.

• When the Sabbath Mode is started, no preheat beep will

sound.

• All prompts, messages and beeps are deactivated when

Sabbath Mode is active.

• Pressing CANCEL will cancel a Bake cycle, however the

control will stay in the Sabbath Mode.

• If power fails, the oven will power up in Sabbath Mode with

72 hours remaining and no cycle active.

Oven Cooking

Broiling

To set Broil:

1. Press the Broil pad.

• “BROIL” flashes.

• SET is displayed.

2. Press the More+ pad to set HI broil or press the Less- pad

to set LO broil.

• HI or LO will be displayed.

• Select HI broil (550° F) for normal broiling. Select

LO broil (450° F) for low-temperature broiling of longer

cooking foods such as poultry.

3. After four seconds, the oven will start.

• “BROIL” will remain lit.

Broil Notes:

• For best results when broiling, use a pan designed for

broiling.

• Expect broil times to increase and browning to be

slightly lighter if appliance is installed on a 208-volt

circuit.

• HI is used for most broiling. Use LO broil when broiling

longer cooking foods. The lower temperature allows

food to cook to the well done stage without excessive

browning.

• Broil times may be longer when the lower broiling

temperature is selected.

• Food should be turned halfway through broiling time.

4. For optimum browning, preheat broil element for 3-4

minutes before adding food.

5. Place food in the oven. Leave oven door open about four

inches (the first stop).

6. Turn meat once about halfway through cooking.

7. When food is cooked, press the CANCEL

pad. Remove food and broiler pan from the

oven.

• The time of day will reappear in the

display.

RACK TOTAL

FOODS POSITION* DONENESS COOK TIME

Beef

Steak, 1” thick 4 Medium 15 - 18 minutes

4 Well Done 19 - 23 minutes

Hamburgers, 3/4” thick 4 Well Done 15 - 18 minutes

Pork

Bacon 4 Well Done 6 - 10 minutes

Chops, 1” 4 Well Done 22 - 26 minutes

Ham - precooked slice, 1/2" thick 4 Warm 8 - 12 minutes

Poultry LO Broil

Chicken Pieces 3 or 4 Well Done 28 - 38 minutes

Seafood

Fish Steaks, buttered, 1” thick 4 Flaky 10 - 15 minutes

Fillets 4 Flaky 8 - 12 minutes

Broiling Chart

* The top rack position is #5.

Note: This chart is a suggested guide. The times may vary with the food being cooked.

Oven Cooking

Oven Light

Press the Oven Light switch on the control panel to

turn the oven light on and off.

Oven Bottom

Protect oven bottom against spillovers, especially acidic or

sugary spills, as they may discolor the porcelain enamel. Use

the correct pan size to avoid spillovers and boilovers. Do not

place utensils or aluminum foil directly on the oven

bottom.

Oven Vent

When the oven is in use the area near the vent may become

hot enough to cause burns. Never block the vent opening.

The oven vent is located below the backguard vent

shield on your range.

CAUTION

Oven Racks

• Do not attempt to change the rack position when the oven

is hot.

• Do not use the oven for storing food or cookware.

OVEN VENT

LOCATION

Do not place

plastics near the

vent opening as

heat from the vent

could distort or

melt the plastic.

The oven has two racks. All racks are designed with a lock-

stop edge.

To remove:

1. Pull rack straight out until it

stops at the lock-stop position.

2. Lift up on the front of the rack

and pull out.

To replace:

1. Place rack on the rack supports in the oven.

2. Tilt the front end up slightly. Slide rack back until it clears

the lock-stop position.

3. Lower front and slide back into the oven.

Do not cover an entire rack with aluminum foil or place foil

on the oven bottom. Baking results will be affected and

damage may occur to the oven bottom.

Rack Positions

RACK 5 (highest

position): Used for

toasting bread or

broiling thin, non-fatty

foods.

RACK 4: Used for

most broiling.

RACK 3: Used for most

baked goods on a

cookie sheet or jelly roll pan, layer cakes, fruit pies, or frozen

convenience foods.

RACK 2: Used for roasting small cuts of meat, casseroles,

baking loaves of bread, bundt cakes or custard pies.

RACK 1: Used for roasting large cuts of meat and poultry,

frozen pies, dessert souffles or angel food cake.

MULTIPLE RACK COOKING:

Two flat racks: Use rack positions 2 and 4.

One flat rack and one offset rack: Use rack positions

2 and 5.

Note: Use caution when removing the offset rack from

position 1 (lowest position).

Oven Cooking

Create-A-Space

Half Rack

Select range models are equipped

with a convertible half rack. The left

side of the rack can be removed

to accommodate a large roaster

on the lower rack. The right side

of the rack is still available to

hold a casserole dish.

Notes:

• The removable section of the rack can be used as a

roasting rack in the broiling pan. Do not use the top

insert when using the rack in the broiling pan.

• The removable section of the rack can be used as a

cooling rack or trivet.

• Make sure oven is cool before removing or reinstalling

the half rack.

• Do not use cookware that extends beyond edge of rack.

• For best results, allow two inches between the pan

placed on the rack and the oven side wall.

• Use caution when removing items from the half rack to

avoid burns.

• Carefully remove items from the lower rack to avoid

disturbing the half rack.

EasyRack

(select models)

Select range models are equipped with an EasyRack

. This

rack offers a convenient place to grasp bakeware when

taking it out of the oven.

Notes:

• Use the EasyRack

only in the oven in which it was

purchased.

• The EasyRack

can be used in all rack positions.

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

Self-Clean Oven

CAUTION

• It is normal for parts of the range to become hot during a

self-clean cycle.

• To prevent personal injury and damage to the oven door

do not attempt to open door when “LOCK” is displayed.

• Avoid touching cooktop, door, window or oven vent area

during a clean cycle.

• Do not use commercial oven cleaners on the oven finish

or around any part of the oven. They will damage the

finish or parts.

The self-clean cycle uses above-normal cooking temperatures

to automatically clean the oven interior. Do not force the oven

door or lock lever open. This may result in exposure to high

temperatures and be a burn hazard.

The oven should be cleaned regularly by wiping up spillovers

to prevent excessive smoke and flare-ups. Do not allow a

heavy build-up of soil to accumulate in the oven.

During the cleaning process, the kitchen should be well

ventilated to get rid of normal odors associated with cleaning.

Before Self-Cleaning

1. Turn off the oven light before cleaning. The light may burn

out during the clean cycle.

2. Remove broiler pan, all pans, and oven racks from the

oven. The oven racks will discolor and may not slide easily

after a self-clean cycle if they are not removed.

3. Clean oven frame, door frame, area

outside of gasket, and around the

opening in the door gasket with a

nonabrasive cleaner such as Bon

Ami* or detergent and water. The

self-cleaning process does not

clean these areas. They should be

cleaned to prevent soil from baking on during the clean

cycle. (The gasket is the seal around the oven door and

window.)

4. To prevent damage, do not clean or rub the gasket around

the oven door. The gasket is designed to seal in heat

during the clean cycle.

5. Wipe up excess grease or spillovers from the oven bottom.

This prevents excessive smoking, flare-ups or flaming

during the clean cycle.

To set Self-Clean:

Note: Oven temperature must be below 400° F to program

a clean cycle.

1. Close the oven door.

2. Move door lock lever right to the locked position.

3. Press the Clean pad.

• “CLEAN” flashes in the display.

If the door is not closed, beeps will sound and “DOOR” will

display. If the door is not closed within 45 seconds, the

self-cleaning operation will be canceled and the display

will return to the time of day.

4. Press the More+ or Less- pad.

• “CL-M” (Medium Soil, 3 hours) is displayed.

5. Press the More+ or Less- pad to scroll through

the self-cleaning settings.

CL-H” (Heavy Soil, 4 hours)

CL-M” (Medium soil, 3 hours)

CL-L” (Light Soil, 2 hours)

Choosing the soil level of the oven automatically programs

the self-cleaning time.

6. After four seconds, the oven will start cleaning.

• The cleaning time will start counting down in the display.

• “LOCK” will appear in the display.

• “CLEAN” will appear in the display.

To Delay a Self-Clean Cycle:

1. Press the Delay pad.

• “DELAY” flashes.

• 00:00 will appear in the display.

2. Press the More+ or Less- pad to set the

amount of time you want to delay the

cycle. Delay time can be set from ten

minutes (00:10) to 11 hours, 59 minutes

(11:59).

cont.

Care & Cleaning

6. Wipe up sugary and acidic spillovers such as sweet

potatoes, tomato, or milk-based sauces. Porcelain enamel

is acid-resistant, not acid-proof. The porcelain finish may

discolor if acidic spills are not wiped up before a self-clean

cycle.

Care & Cleaning

5. Press the More+ or Less- pad to scroll through the self-

cleaning settings.

CL-H” (Heavy Soil, 4 hours)

CL-M” (Medium soil, 3 hours)

CL-L” (Light Soil, 2 hours)

Choosing the soil level of the oven automatically programs

the self-cleaning time.

6. After four seconds, CLEAN, DELAY and LOCK will appear

in the display to show that the oven is set for a delayed

clean operation. The delay time is displayed.

Notes:

• If the oven door is left open, “DOOR” will flash in the

display and a signal will beep until the door is closed

and the Clean pad is pressed again.

• If more than five seconds elapse between pressing the

Clean pad and the More+ or Less- pad, the program will

automatically return to the previous display.

• The oven door will be damaged if the oven door is

forced to open when “LOCK” is still displayed.

During the Self-Clean Cycle

When LOCK shows in the display, the door cannot be opened.

To prevent damage to the door, do not force the door open

when LOCK is displayed.

Smoke and Smells

You may see some smoke and smell an odor the first few

times the oven is cleaned. This is normal and will lessen in

time.

Smoke may also occur if the oven is heavily soiled or if a

broiler pan was left in the oven.

Sounds

As the oven heats, you may hear sounds of metal parts

expanding and contracting. This is normal and will not

damage the oven.

After Self-Cleaning

About one hour after the end of the self-clean cycle, LOCK

will turn off. The door can then be opened. Move door lock

lever to the left to unlock.

Some soil may leave a light gray, powdery ash. Remove

it with a damp cloth. If soil remains after wiping, that means

the clean cycle was not long enough. The soil will be re-

moved during the next clean cycle.

If oven racks were left in the oven and do not slide

smoothly after a clean cycle, wipe racks and rack supports

with a small amount of vegetable oil to make them easier to

move.

Fine lines may appear in the porcelain because it went

through heating and cooling. This is normal and will not

affect performance.

A white discoloration may appear after cleaning if acidic

or sugary foods were not wiped up before the self-clean

cycle. This discoloration is normal and will not affect perfor-

mance.

If the oven has already been set for a clean

cycle and you wish to set a delay:

1. Press the Delay pad.

• “DELAY” flashes.

• 00:00 will appear in the display.

2. Press the More+ or Less- pad to set the

amount of time you want to delay the cycle.

After four seconds, CLEAN, DELAY and LOCK will appear

in the display to show that the oven is set for a delayed

clean operation. The delay time is displayed.

When the Self-Clean cycle starts:

• “DELAY” will turn off.

• The clean time will appear in the display.

To cancel the Self-Clean cycle:

Press the CANCEL pad.

• All words disappear from the display.

• All functions are canceled.

• The time of day appears in the display.

3. Press the Clean pad.

• “CLEAN” will flash.

4. Press the More+ or Less- pad.

• “CL-M” (Medium Soil, 3 hours)

is displayed.

Care & Cleaning

PART PROCEDURE

CAUTION

Cleaning Procedures

• Be sure appliance is off and all parts are cool before handling

or cleaning. This is to avoid damage and possible burns.

• To prevent staining or discoloration, clean appliance after each use.

• If a part is removed, be sure it is correctly replaced.

Backguard and Porcelain enamel is glass fused on metal and may crack or chip with misuse. It is acid resistant, not acid

Cooktop – proof. All spillovers, especially acidic or sugary spillovers, should be wiped up immediately with a dry cloth.

Porcelain Enamel • When cool, wash with soapy water, rinse and dry.

• Never wipe off a warm or hot surface with a damp cloth. This may cause cracking or chipping.

• Never use oven cleaners, abrasive or caustic cleaning agents on exterior finish of range.

Broiler Pan and Never cover insert with aluminum foil as this prevents the fat from draining to the pan below.

Insert • Place soapy cloth over insert and pan; let soak to loosen soil.

• Wash in warm soapy water. Use scouring pad to remove stubborn soil.

• Broiler pan and insert can be cleaned in dishwasher.

Clock and • To activate “Control Lock” for cleaning, see page 9.

Control Pad • Wipe with a damp cloth and dry. Do not use abrasive cleaning agents as they may scratch the surface.

Area • Glass cleaners may be used if sprayed on a cloth first. DO NOT spray directly on control pad and

display area.

Control Knobs • Remove knobs in the OFF position by pulling forward.

• Wash, rinse and dry. Do not use abrasive cleaning agents as they may scratch the finish.

• Turn on each element to be sure the knobs have been correctly replaced.

Cooktop – Never use oven cleaners, chlorine bleach, ammonia or glass cleaners with ammonia. NOTE: Call

Glass-Ceramic an authorized servicer if the glass-ceramic top should crack, break or if metal or aluminum foil

should melt on the cooktop.

• Allow the cooktop to cool before cleaning.

• General – Clean cooktop after each use, or when needed, with a damp paper towel and Cooktop Cleaning

Creme* (Part No. 20000001)**. Then, buff with a clean dry cloth.

NOTE: Permanent stains will develop if soil is allowed to cook on by repeatedly using the cooktop when soiled.

• Heavy Soils or Metal Marks – Dampen a “scratchless” or “never scratch” scrubber sponge. Apply

Cooktop Cleaning Creme* (Part No. 20000001)** and scrub to remove as much soil as possible. Apply a

thin layer of the creme over the soil, cover with a damp paper towel and let stand 30 to 45 minutes (2-3

hours for very heavy soil). Keep moist by covering the paper towel with plastic wrap. Scrub again, then

buff with a clean dry cloth.

NOTE: Only use a CLEAN, DAMP “scratchless” pad that is safe for non-stick cookware. The pattern and glass

will be damaged if the pad is not damp, if the pad is soiled, or if another type of pad is used.

• Burned-on or Crusty Soils – Scrub with a “scratchless” or “never scratch” scouring pad and Cooktop

Cleaning Creme*.

NOTE: Hold a razor blade scraper at 30

angle and scrape any remaining soil. Then, clean as de-

scribed above. Do not use the razor blade for daily cleaning as it may wear the pattern on the glass.

• Melted Sugar or Plastic – Immediately turn element to LOW and scrape sugar or

plastic from hot surface to a cool area. Then turn element OFF and allow to cool. Clean

residue with razor blade scraper and Cooktop Cleaning Creme*.

* Brand names are registered trademarks of the

respective manufacturers.

** To order call 1-877-232-6771 USA and

1-800-688-8408 Canada.

La page charge ...

Maytag MER5751BAB - 30 Inch Electric Range Mode d'emploi

Marque: Maytag

Modèle: MER5751BAB - 30 Inch Electric Range

Catégorie: Cuisinières

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MER5751BAB - 30 Inch Electric Range User guide
español: Maytag MER5751BAB - 30 Inch Electric Range Guía del usuario

Documents connexes

Autres documents

Amana 700 Manuel utilisateur