ARTHUR MARTIN ELECTROLUX AGG7536K Manuel utilisateur

Catégorie
Plaques de cuisson
Taper
Manuel utilisateur
AGG7536K
EN Hob User Manual 2
FR Table de cuisson Notice d'utilisation 17
CONTENTS
Safety information 2
Safety instructions 4
Installation 7
Product description 10
Daily use 10
Hints and tips 12
Care and cleaning 12
Troubleshooting 14
Technical data 15
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible for any injuries or damages that are the result of
incorrect installation or usage. Always keep the instructions
in a safe and accessible location for future reference.
Children and vulnerable people safety
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
unless continuously supervised.
Children of less than 3 years of age should be kept away
unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep children and pets away from the appliance when it
operates or when it cools down. Accessible parts are hot.
If the appliance has a child safety device, it should be
activated.
Children shall not carry out cleaning and user maintenance
of the appliance without supervision.
2
General Safety
WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to avoid
touching heating elements.
Do not operate the appliance by means of an external
timer or separate remote-control system.
WARNING: Unattended cooking on a hob with fat or oil
can be dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire
blanket.
CAUTION: The cooking process has to be supervised. A
short term cooking process has to be supervised
continuously.
WARNING: Danger of fire: Do not store items on the
cooking surfaces.
Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they can get
hot.
Do not use a steam cleaner to clean the appliance.
If the glass ceramic surface / glass surface is cracked,
switch off the appliance and unplug it from the mains. In
case the appliance is connected to the mains directly using
junction box, remove the fuse to disconnect the appliance
from power supply. In either case contact the Authorised
Service Centre.
In case of hotplate glass breakage:
shut immediately off all burners and any electrical
heating element and isolate the appliance from the
power supply,
do not touch the appliance surface,
do not use the appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer, an authorized Service or similarly qualified
persons in order to avoid a hazard.
3
Where the appliance is directly connected to the power
supply, an all-pole isolating switch with a contact gap is
required. Complete disconnection in compliance with the
conditions specified in overvoltage category III must be
guaranteed. The earth cable is excluded from this.
When you route the mains cable, make sure that the cable
doesn't come into direct contact (for example using
insulating sleeving) with parts that can reach temperatures
of more than 50°C above room temperature.
WARNING: Use only hob guards designed by the
manufacturer of the cooking appliance or indicated by the
manufacturer of the appliance in the instructions for use as
suitable or hob guards incorporated in the appliance. The
use of inappropriate guards can cause accidents.
SAFETY INSTRUCTIONS
This appliance is suitable for the following
markets: MA TN
Installation
WARNING! Only a qualified
person must install this
appliance.
WARNING! Risk of injury or
damage to the appliance.
Remove all the packaging.
Do not install or use a damaged
appliance.
Follow the installation instructions
supplied with the appliance.
Keep the minimum distance from other
appliances and units.
Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
Protect the bottom of the appliance
from steam and moisture.
Do not install the appliance adjacent to
a door or under a window. This
prevents hot cookware falling from the
appliance when the door or the window
is opened.
If the appliance is installed above
drawers make sure that the space,
between the bottom of the appliance
and the upper drawer, is sufficient for
air circulation.
The bottom of the appliance can get
hot. Make sure to install a non-
combustible separation panel under the
appliance to prevent access to the
bottom.
Electrical Connection
WARNING! Risk of fire and
electric shock.
All electrical connections should be
made by a qualified electrician.
The appliance must be earthed.
Before carrying out any operation make
sure that the appliance is disconnected
from the power supply.
Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
Make sure the appliance is installed
correctly. Loose and incorrect electricity
4
mains cable or plug (if applicable) can
make the terminal become too hot.
Use the correct electricity mains cable.
Do not let the electricity mains cable
tangle.
Make sure that a shock protection is
installed.
Use the strain relief clamp on the cable.
Make sure the mains cable or plug (if
applicable) does not touch the hot
appliance or hot cookware, when you
connect the appliance to the near
sockets.
Do not use multi-plug adapters and
extension cables.
Make sure not to cause damage to the
mains plug (if applicable) or to the
mains cable. Contact our Authorised
Service Centre or an electrician to
change a damaged mains cable.
The shock protection of live and
insulated parts must be fastened in
such a way that it cannot be removed
without tools.
Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
If the mains socket is loose, do not
connect the mains plug.
Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
The electrical installation must have an
isolation device which lets you
disconnect the appliance from the
mains at all poles. The isolation device
must have a contact opening width of
minimum 3 mm.
Gas connection
All gas connections should be made by
a qualified person.
Before installation, make sure that the
local distribution conditions (nature of
the gas and gas pressure) and the
adjustment of the appliance are
compatible.
Make sure that there is air circulation
around the appliance.
The information about the gas supply is
on the rating plate.
This appliance is not connected to a
device, which evacuates the products
of combustion. Make sure to connect
the appliance according to current
installation regulations. Pay attention to
requirements regarding adequate
ventilation.
Use
WARNING! Risk of injury,
burns and electric shock.
Remove all the packaging, labelling
and protective film (if applicable) before
first use.
Use this appliance in a household
environment.
Do not change the specification of this
appliance.
Make sure that the ventilation openings
are not blocked.
Do not let the appliance stay
unattended during operation.
Set the cooking zone to “off” after each
use.
Do not put cutlery or saucepan lids on
the cooking zones. They can become
hot.
Do not operate the appliance with wet
hands or when it has contact with
water.
Do not use the appliance as a work
surface or as a storage surface.
When you place food into hot oil, it may
splash.
WARNING! Risk of fire and
explosion
Fats and oil when heated can release
flammable vapours. Keep flames or
heated objects away from fats and oils
when you cook with them.
The vapours that very hot oil releases
can cause spontaneous combustion.
5
Used oil, that can contain food
remnants, can cause fire at a lower
temperature than oil used for the first
time.
Do not put flammable products or items
that are wet with flammable products
in, near or on the appliance.
WARNING! Risk of damage to
the appliance.
Do not keep hot cookware on the
control panel.
Do not let cookware to boil dry.
Be careful not to let objects or
cookware fall on the appliance. The
surface can be damaged.
Do not activate the cooking zones with
empty cookware or without cookware.
Do not put aluminium foil on the
appliance.
Cookware made of cast iron, aluminium
or with a damaged bottom can cause
scratches on the glass / glass ceramic.
Always lift these objects up when you
have to move them on the cooking
surface.
Use only stable cookware with the
correct shape and diameter larger than
the dimensions of the burners.
Make sure cookware is centrally
positioned on the burners.
Make sure the flame does not go out
when you quickly turn the knob from
the maximum to the minimum position.
Use only the accessories supplied with
the appliance.
Do not install a flame diffuser on the
burner.
The use of a gas cooking appliance
results in the production of heat and
moisture. Provide good ventilation in
the room where the appliance is
installed.
Prolonged intensive use of the
appliance may call for additional
ventilation, for example opening of a
window, or more effective ventilation,
for example increasing the level of
mechanical ventilation where present.
This appliance is for cooking purposes
only. It must not be used for other
purposes, for example room heating.
Do not let acid liquids, for example
vinegar, lemon juice or limescale
remover, touch the hob. This can cause
matt patches.
Discoloration of the enamel or stainless
steel has no effect on the performance
of the appliance.
Care and cleaning
WARNING! Do not remove the
buttons, knobs or gaskets from
the control panel. Water may
get inside the appliance and
cause damage.
Clean the appliance regularly to
prevent the deterioration of the surface
material.
Deactivate the appliance and let it cool
down before you clean it.
Disconnect the appliance from the
electrical supply before maintenance.
Do not use water spray and steam to
clean the appliance.
Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use any abrasive products,
abrasive cleaning pads, solvents or
metal objects.
Do not clean the burners in the
dishwasher.
Service
To repair the appliance contact an
Authorised Service Centre.
Use original spare parts only.
Disposal
WARNING! Risk of injury or
suffocation.
Contact your municipal authority for
information on how to discard the
appliance correctly.
Disconnect the appliance from the
mains supply.
6
Cut off the mains electrical cable close
to the appliance and dispose of it.
Flat the external gas pipes.
INSTALLATION
WARNING! Refer to Safety
chapters.
Before the installation
Before you install the hob, write down the
information bellow from the rating plate.
The rating plate is on the bottom of the
hob.
Model .......................................
PNC .........................................
Serial number ...........................
Gas Connection
WARNING! The following
instructions about installation,
connection and maintenance
must be carried out by qualified
personnel in compliance with
standards and local regulations
in force.
Choose fixed connections or use a flexible
pipe in stainless steel in compliance with
the regulation in force. If you use flexible
metallic pipes, be careful they do not
come in touch with mobile parts or they
are not squeezed. Also be careful when
the hob is put together with an oven.
Make sure that the gas supply
pressure of the appliance
obeys the recommended
values. The adjustable
connection is fixed to the
comprehensive ramp by means
of a threaded nut G 1/2". Screw
the parts without force, adjust
the connection in the
necessary direction and tighten
everything.
A B C
A. End of shaft with nut
B. Washer supplied with the appliance
C. Elbow supplied with the appliance
Liquid gas
Use the rubber pipe holder for liquid gas.
Always engage the gasket. Then continue
with the gas connection.
The flexible pipe is prepared for apply
when:
it can not get hot more than room
temperature, higher than 30°C;
it is no longer than 1500 mm;
it shows no throttles;
it is not subject to traction or torsion;
it does not get in touch with cutting
edges or corners;
it can be easily examined in order to
make sure its condition.
The control of preservation of the flexible
pipe consists in checking that:
it does not show cracks, cuts, marks of
burnings on the two ends and on its full
length;
the material is not hardened, but shows
its correct elasticity;
the fastening clamps are not rusted;
expired term is not due.
If one or more defects are visible, do not
repair the pipe, but replace it.
WARNING! When installation
is complete, make sure that the
seal of each pipe fitting is
correct. Use a soapy solution,
not a flame!
7
Injectors replacement
1. Remove the pan supports.
2. Remove the caps and crowns of the
burner.
3. With a socket spanner 7 remove the
injectors and replace them with the
ones which are necessary for the type
of gas you use (see table in "Technical
Data" chapter).
4. Assemble the parts, follow the same
procedure backwards.
5. Replace the rating plate (it is near the
gas supply pipe) with the one for the
new type of gas supply. You can find
this plate in the package supplied with
the appliance.
If the supply gas pressure is changeable
or different from the necessary pressure,
you must fit an applicable pressure
adjuster on the gas supply pipe.
Adjustment of minimum level
To adjust the minimum level of the
burners:
1. Light the burner.
2. Turn the knob on the minimum
position.
3. Remove the knob .
4. With a thin screwdriver, adjust the
bypass screw position (A).
A
5. If you change:
from natural gas G20 20 mbar to
liquid gas, fully tighten the bypass
screw in.
from liquid gas to natural gas G20
20 mbar, undo the bypass screw
approximately 1/4 of a turn (1/2 of a
turn for Multi Crown burner).
WARNING! Make sure the
flame does not go out when
you quickly turn the knob from
the maximum position to the
minimum position.
Electrical connection
Make sure that the rated voltage and
type of power on the rating plate agree
with the voltage and the power of the
local power supply.
This appliance is supplied with a mains
cable. It has to be supplied with a
correct plug which can hold the load
that the rating plate rates. Make sure
that you install the plug in a correct
socket.
Always use a correctly installed
shockproof socket.
Make sure that there is an access to
the mains plug after the installation.
Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
There is a risk of fire when the
appliance is in connection with an
extension cable, an adapter or a
multiple connection. Make sure that the
ground connection agrees with the
standards and regulations.
Do not let the power cable to heat up to
a temperature higher than 90° C.
Make sure that you connect the
blue neutral cable to the
terminal with a letter "N" on it.
Connect the brown (or black)
phase cable to the terminal
which has a letter "L". Keep the
phase cable connected at all
times.
Connection cable
To replace the connection cable use only
the special cable or its equivalent. The
cable type is: H03V2V2-FT90.
Make sure that the cable section is
applicable to the voltage and the working
temperature. The yellow / green earth wire
8
must be approximately 2 cm longer than
the brown (or black) phase wire.
Assembly
1.
2.
3.
min.
55 mm
min.
650 mm
560 mm
2
0
+
480 mm
2
0
+
min.
150 mm
30 mm
4.
5.
6.
B
A
A) supplied seal
B) supplied brackets
7.
CAUTION! Install the appliance
only on a worktop with flat
surface.
Possibilities for insertion
The panel installed below the hob must be
easy to remove and let an easy access in
case a technical assistance intervention is
necessary.
9
Kitchen unit with door
min 20 mm
(max 150 mm)
30 mm
60 mm
B
A
A. Removable panel
B. Space for connections
Kitchen unit with oven
The electrical connection of the hob and
the oven must be installed separately for
safety reasons and to let easy remove
oven from the unit.
PRODUCT DESCRIPTION
Cooking surface layout
1
4
3
2
1
Semi-rapid burner
2
Multi Crown burner
3
Auxiliary burner
4
Control knobs
Control knob
Symbol Description
no gas supply / off posi‐
tion
Symbol Description
ignition position / maxi‐
mum gas supply
minimum gas supply
DAILY USE
WARNING! Refer to Safety
chapters.
10
Burner overview
A
B
D
C
C
D
A
B
A. Burner cap
B. Burner crown
C. Ignition candle
D. Thermocouple
Ignition of the burner
Always light the burner before
you put on the cookware.
WARNING! Be very careful
when you use open fire in the
kitchen environment. The
manufacturer declines any
responsibility in case of the
flame misuse.
1. Push the control knob down and turn it
counterclockwise to the maximum gas
supply position ( ).
2. Keep the control knob pushed for
equal or less than 10 seconds. This
lets the thermocouple warm up. If not,
the gas supply is interrupted.
3. Adjust the flame after it is regular.
If after some tries the burner
does not light, check if the
crown and its cap are in correct
positions.
WARNING! Do not keep the
control knob pushed for more
than 15 seconds. If the burner
does not light after 15 seconds,
release the control knob, turn it
into off position and try to light
the burner again after minimum
1 minute.
CAUTION! In the absence of
electricity you can ignite the
burner without electrical device;
in this case approach the
burner with a flame, turn the
control knob counter-clockwise
to maximum gas supply
position and push it down.
Keep the control knob pushed
for equal or less than 10
seconds to let the
thermocouple warm up.
If the burner accidentally goes
out, turn the control knob to the
off position and try to light the
burner again after minimum 1
minute.
The spark generator can start
automatically when you switch
on the mains, after installation
or a power cut. It is normal.
The hob is supplied with the
progressive valves. They make
the flame regulation more
precise.
11
Turning the burner off
To put the flame out, turn the knob to the
off position .
WARNING! Always turn the
flame down or switch it off
before you remove the pans
from the burner.
HINTS AND TIPS
WARNING! Refer to Safety
chapters.
Cookware
CAUTION! Do not use cast
iron pans, clay or earthenware
pots, grill or toaster plates.
WARNING! Do not put the
same pan on two burners.
WARNING! Do not put
unstable or damaged pots on
the burner to prevent spills and
injuries.
CAUTION! Make sure that the
bottoms of pots do not stand
too close to the control knob,
otherwise the flame heats the
control knob up.
CAUTION! Make sure that pot
handles are not above the front
edge of the cooktop.
CAUTION! Make sure that the
pots are placed centrally on the
burner in order to get the
maximum stability and a lower
gas consumption.
CAUTION! Liquids spilt during
cooking can cause the glass to
break.
Energy saving
If it is possible, always put the lids on
the cookware.
When the liquid starts to boil, turn down
the flame to barely simmer the liquid.
Diameters of cookware
Use cookware with diameters
applicable to the size of
burners.
Burner Diameter of
cookware
(mm)
Multi Crown 220 - 260
Semi-rapid (rear left) 120 - 240
Semi-rapid (rear right) 120 - 240
Semi-rapid (front left) 120 - 220
Auxiliary 80 - 180
CARE AND CLEANING
WARNING! Refer to Safety
chapters.
General information
Clean the hob after each use.
Always use cookware with a clean
base.
Scratches or dark stains on the surface
have no effect on how the hob
operates.
Use a special cleaner suitable for the
surface of the hob.
12
WARNING! Do not use knives,
scrapers or similar instruments
to clean the surface of the
glass or the rims of the burners
and the frame (if applicable).
Wash stainless steel parts with water,
and then dry them with a soft cloth.
Pan supports
The pan supports are not
resistant to washing in a
dishwasher. They must be
washed by hand.
1. Remove the pan supports to easily
clean the hob.
Be very careful when you
replace the pan supports to
prevent the hob top from
damage.
2. The enamel coating occasionally can
have rough edges, so be careful when
you wash the pan supports by hand
and dry them. If necessary, remove
stubborn stains with a paste cleaner.
3. After you clean the pan supports,
make sure that they are in correct
positions.
4. For the burner to operate correctly,
make sure that the arms of the pan
supports are aligned with the centre of
the burner.
Removing pan supports
To keep the pan supports in the correct
position, they are put on metal pins
installed in the rear side of the hob. For
easier cleaning, pan supports can be
removed from the hob. Lift up the pan
supports keeping them in horizontal
position as shown in the graphic.
Do not lift the pan supports at
an angle, as this will put strain
on the metal pins. This can
cause damage to the pins and
cause them to break.
The shape of pan supports and the
amount of burners can be different in
other models of the appliance.
13
Cleaning the hob
Remove immediately: melted plastic,
plastic foil, sugar and food with sugar,
otherwise, the dirt can cause damage
to the hob. Take care to avoid burns.
Remove when the hob is sufficiently
cool: limescale rings, water rings, fat
stains, shiny metallic discoloration.
Clean the hob with a moist cloth and a
non-abrasive detergent. After cleaning,
wipe the hob dry with a soft cloth.
To clean the enamelled parts, caps and
crowns, wash them with warm soapy
water and dry them carefully before you
put them back on.
Cleaning the spark plug
This feature is obtained through a ceramic
ignition candle with a metal electrode.
Keep these components well clean to
prevent difficult lighting and check that the
burner crown holes are not obstructed.
Periodic maintenance
Speak to your local Authorised Service
Centre periodically to check the conditions
of the gas supply pipe and the pressure
adjuster, if fitted.
TROUBLESHOOTING
WARNING! Refer to Safety
chapters.
What to do if...
Problem Possible cause Remedy
There is no spark when you
try to activate the spark gen‐
erator.
The hob is not connected to
an electrical supply or it is
connected incorrectly.
Check if the hob is correctly
connected to the electrical
supply.
The fuse is blown. Make sure that the fuse is
the cause of the malfunc‐
tion. If the fuse is blown
again and again, contact a
qualified electrician.
Burner cap and crown are
placed incorrectly.
Place the burner cap and
crown correctly.
The flame extinguishes im‐
mediately after ignition.
Thermocouple is not heated
up sufficiently.
After lightning the flame,
keep the knob pushed for
equal or less than 10 sec‐
onds.
The flame ring is uneven. Burner crown is blocked with
food residues.
Make sure that the injector
is not blocked and the burn‐
er crown is clean.
If you cannot find a solution...
If you cannot find a solution to the problem
yourself, contact your dealer or an
Authorised Service Centre. Give the data
from the rating plate. Make sure, you
operated the hob correctly. If not the
servicing by a service technician or dealer
will not be free of charge, also during the
warranty period. The instructions about
14
the Service Centre and conditions of
guarantee are in the guarantee booklet.
Labels supplied with the
accessories bag
Stick the adhesive labels as indicated
below:
A. Stick it on Guarantee Card and send
this part (if applicable).
B. Stick it on Guarantee Card and keep
this part (if applicable).
C. Stick it on instruction booklet.
TECHNICAL DATA
Hob dimensions
Width 740 mm
Depth 510 mm
Bypass diameters
BURNER Ø BYPASS 1/100 mm
Multi Crown 56
Semi-rapid 35
Auxiliary 28
15
Other technical data
TOTAL POW‐
ER:
Gas original:
G30/G31 (3B/P) 30/30
mbar
745 g/h
Gas replace‐
ment:
G20 (2H) 20 mbar 10,9 kW
Electric supply: 220-240 V ~ 50/60 Hz
Appliance cate‐
gory:
II2H3B/P
Gas connec‐
tion:
G 1/2"
Appliance
class:
3
Gas burners for LPG G30/G31 30/30 mbar
BURNER NORMAL
POWER kW
MINIMUM
POWER kW
INJECTOR
MARK
NOMINAL GAS
FLOW g/h
Multi Crown 3,55 1,4 095 258
Semi-rapid 1,9 0,6 71 138
Auxiliary 1,0 0,33 50 73
Gas burners for NATURAL GAS G20 20 mbar
BURNER NORMAL POWER
kW
MINIMUM POWER
kW
INJECTOR MARK
Multi Crown 3,9 1,4 146
Semi-rapid 2,0 0,6 96x
Auxiliary 1,0 0,33 70
ENVIRONMENTAL CONCERNS
Recycle materials with the symbol . Put
the packaging in relevant containers to
recycle it. Help protect the environment
and human health by recycling waste of
electrical and electronic appliances. Do
not dispose of appliances marked with the
symbol with the household waste.
Return the product to your local recycling
facility or contact your municipal office.
16
TABLE DES MATIÈRES
Informations de sécurité 17
Consignes de sécurité 19
Installation 22
Description de l'appareil 26
Utilisation quotidienne 26
Conseils 28
Entretien et nettoyage 29
En cas d'anomalie de fonctionnement 31
Caractéristiques techniques 32
Sous réserve de modifications.
INFORMATIONS DE SÉCURITÉ
Avant d'installer et d'utiliser cet appareil, lisez
soigneusement les instructions fournies. Le fabricant ne
pourra être tenu pour responsable des blessures et dégâts
résultant d'une mauvaise installation ou utilisation.
Conservez toujours les instructions dans un lieu sûr et
accessible pour vous y référer ultérieurement.
Sécurité des enfants et des personnes vulnérables
Cet appareil peut être utilisé par des enfants de plus de
8 ans, ainsi que des personnes dont les capacités
physiques, sensorielles et mentales sont réduites ou dont
les connaissances et l'expérience sont insuffisantes, à
condition d'être surveillés ou d'avoir reçu des instructions
concernant l'utilisation sécurisée de l'appareil et de
comprendre les risques encourus.
Les enfants entre 3 et 8 ans et les personnes ayant un
handicap très important et complexe doivent être tenus à
l'écart, à moins d'être surveillés en permanence.
Les enfants de moins de 3 ans doivent être tenus à l'écart,
à moins d'être surveillés en permanence.
Ne laissez pas les enfants jouer avec l'appareil.
Ne laissez pas les emballages à la portée des enfants et
jetez-les convenablement.
Tenez les enfants et les animaux éloignés de l'appareil
lorsqu'il est en cours de fonctionnement ou lorsqu'il
refroidit. Les parties accessibles sont chaudes.
Si l'appareil est équipé d'un dispositif de sécurité enfants,
nous vous recommandons de l'activer.
17
Les enfants ne doivent pas nettoyer ni entreprendre une
opération de maintenance sur l'appareil sans surveillance.
Sécurité générale
AVERTISSEMENT : L'appareil et ses parties accessibles
deviennent chauds pendant son fonctionnement. Veillez à
ne pas toucher les éléments chauffants.
Ne faites pas fonctionner l'appareil avec un minuteur
externe ou un système de commande à distance.
AVERTISSEMENT : Il peut être dangereux de laisser
chauffer de la graisse ou de l'huile sans surveillance sur
une table de cuisson car cela pourrait provoquer un
incendie.
N'essayez JAMAIS d'éteindre un feu avec de l'eau.
Éteignez l'appareil puis couvrez les flammes, par exemple
avec un couvercle ou une couverture ignifuge.
ATTENTION : Toute cuisson doit être surveillée. Une
cuisson courte doit être surveillée en permanence.
AVERTISSEMENT : Risque d'incendie : N'entreposez rien
sur les surfaces de cuisson.
Ne posez pas d'objets métalliques tels que couteaux,
fourchettes, cuillères ou couvercles sur la table de cuisson
car ils pourraient chauffer.
N'utilisez pas de nettoyeur vapeur pour nettoyer l'appareil.
Si la surface vitrocéramique / en verre est fissurée,
éteignez l'appareil et débranchez-le. Si l'appareil est
branché à l'alimentation secteur directement en utilisant
une boîte de jonction, retirez le fusible pour déconnecter
l'appareil de l'alimentation secteur. Dans tous les cas,
contactez le service après-vente agréé.
En cas de bris de verre de la plaque de cuisson :
éteignez immédiatement tous les brûleurs et toutes les
résistances électriques puis isolez l'appareil de
l'alimentation électrique,
ne touchez pas la surface de l'appareil,
n'utilisez plus l'appareil.
18
Si le câble d'alimentation est endommagé, il doit être
remplacé par le fabricant, un service de maintenance
agréé ou un technicien qualifié afin d'éviter tout danger.
Si l'appareil est relié directement à l'alimentation
électrique, installez un sectionneur avec une ouverture de
contact. Il est indispensable de garantir une déconnexion
complète conformément aux conditions de surtension de
catégorie III. Le fil de terre n'est pas concerné.
Lorsque vous acheminez le câble d'alimentation, assurez-
vous qu'il n'entre pas en contact direct (par exemple, à
l'aide d'un manchon isolant) avec des parties pouvant
atteindre des températures supérieures de 50 °C à la
température ambiante.
AVERTISSEMENT : Utilisez uniquement les dispositifs de
protection pour table de cuisson conçus ou indiqués
comme adaptés par le fabricant de l'appareil de cuisson
dans les instructions d'utilisation, ou les dispositifs de
protection pour table de cuisson intégrés à l'appareil.
L'utilisation de dispositifs de protection non adaptés peut
entraîner des accidents.
CONSIGNES DE SÉCURITÉ
Cet appareil est adapté aux marchés
suivants: MA TN
Installation
AVERTISSEMENT! L'appareil
doit être installé uniquement
par un professionnel qualifié.
AVERTISSEMENT! Risque de
blessure corporelle ou de
dommages matériels.
Retirez l'intégralité de l'emballage.
N'installez pas et ne branchez pas un
appareil endommagé.
Suivez scrupuleusement les
instructions d'installation fournies avec
l'appareil.
Respectez l'espacement minimal requis
par rapport aux autres appareils et
éléments.
Soyez toujours vigilants lorsque vous
déplacez l'appareil car il est lourd.
Utilisez toujours des gants de sécurité
et des chaussures fermées.
Isolez les surfaces découpées à l'aide
d'un matériau d'étanchéité pour éviter
que la moisissure ne provoque de
gonflements.
Protégez la partie inférieure de
l'appareil de la vapeur et de l'humidité.
N'installez pas l'appareil près d'une
porte ou sous une fenêtre. Les
récipients chauds risqueraient de
tomber de l'appareil lors de l'ouverture
de celles-ci.
Si l'appareil est installé au-dessus de
tiroirs, assurez-vous qu'il y a
19
suffisamment d'espace entre le fond de
l'appareil et le tiroir supérieur pour que
l'air puisse circuler.
Le dessous de l'appareil peut devenir
très chaud. Veillez à installer un
panneau de séparation ignifuge sous
l'appareil pour en bloquer l'accès.
Branchement électrique
AVERTISSEMENT! Risque
d'incendie ou d'électrocution.
L'ensemble des branchements
électriques doit être effectué par un
technicien qualifié.
L'appareil doit être relié à la terre.
Avant toute intervention, assurez-vous
que l'appareil est débranché.
Vérifiez que les paramètres figurant sur
la plaque signalétique correspondent
aux données électriques de votre
réseau.
Assurez-vous que l'appareil est bien
installé. Un câble d'alimentation lâche
et inapproprié ou une fiche (si
présente) non serrée peuvent être à
l'origine d'une surchauffe des bornes.
Utilisez le câble d'alimentation
électrique approprié.
Ne laissez pas le câble d'alimentation
s'emmêler.
Assurez-vous qu'une protection anti-
électrocution est installée.
Utilisez un collier anti-traction sur le
câble.
Assurez-vous que le câble
d'alimentation ou la fiche (si présente)
n'entrent pas en contact avec les
surfaces brûlantes de l'appareil ou les
récipients brûlants lorsque vous
branchez l'appareil à des prises
électriques situées à proximité.
N'utilisez pas d'adaptateurs multiprises
ni de rallonges.
Veillez à ne pas endommager la fiche
secteur (si présente) ni le câble
d'alimentation. Contactez notre service
après-vente agréé ou un électricien
pour remplacer le câble d'alimentation
s'il est endommagé.
La protection contre les chocs des
parties sous tension et isolées doit être
fixée de telle manière qu'elle ne peut
pas être enlevée sans outils.
Ne branchez la fiche d'alimentation à la
prise de courant qu'à la fin de
l'installation. Assurez-vous que la prise
de courant est accessible une fois
l'appareil installé.
Si la prise de courant est lâche, ne
branchez pas la fiche d'alimentation
secteur.
Ne tirez jamais sur le câble
d'alimentation pour débrancher
l'appareil. Tirez toujours sur la fiche.
N'utilisez que des systèmes d'isolation
appropriés : des coupe-circuits, des
fusibles (les fusibles à visser doivent
être retirés du support), un disjoncteur
différentiel et des contacteurs.
L'installation électrique doit être
équipée d'un dispositif d'isolement à
coupure omnipolaire. Le dispositif
d'isolement doit présenter une distance
d'ouverture des contacts d'au moins
3 mm.
Raccordement au gaz
Tous les raccordements au gaz doivent
être effectués par une personne
qualifiée.
Avant l'installation, vérifiez que les
conditions de distribution locales
(nature et pression du gaz) sont
compatibles avec le réglage de
l'appareil.
Assurez-vous que l'air circule autour de
l'appareil.
Les informations concernant
l'alimentation en gaz se trouvent sur la
plaque signalétique.
Cet appareil n'est pas raccordé à un
dispositif d'évacuation des produits de
combustion. Assurez-vous de brancher
l'appareil selon les réglementations
d'installation en vigueur. Veillez à
respecter les exigences en matière
d'aération.
20
1 / 1

ARTHUR MARTIN ELECTROLUX AGG7536K Manuel utilisateur

Catégorie
Plaques de cuisson
Taper
Manuel utilisateur

dans d''autres langues