AEG HG755421UM Manuel utilisateur

Marque: AEG

Modèle: HG755421UM

Catégorie: Plaques de cuisson

Taper: Manuel utilisateur

USER

MANUAL

EN User Manual 2

Hob

FR Notice d'utilisation 18

Table de cuisson

HG755421UM

CONTENTS

1. SAFETY INFORMATION.............................................................................................2

2. SAFETY INSTRUCTIONS.............................................................................................4

3. INSTALLATION............................................................................................................7

4. PRODUCT DESCRIPTION.........................................................................................10

5. DAILY USE..................................................................................................................11

6. HINTS AND TIPS........................................................................................................12

7. CARE AND CLEANING.............................................................................................13

8. TROUBLESHOOTING............................................................................................... 13

9. TECHNICAL DATA.................................................................................................... 15

10. ENERGY EFFICIENCY.............................................................................................16

FOR PERFECT RESULTS

Thank you for choosing this AEG product. We have created it to give you

impeccable performance for many years, with innovative technologies that help

make life simpler features you might not find on ordinary appliances. Please

spend a few minutes reading to get the very best from it.

Visit our website for:

Get usage advice, brochures, trouble shooter, service information:

www.aeg.com/webselfservice

www.registeraeg.com

Buy Accessories, Consumables and Original spare parts for your appliance:

www.aeg.com/shop

CUSTOMER CARE AND SERVICE

Always use original spare parts.

When contacting our Authorised Service Centre, ensure that you have the

following data available: Model, PNC, Serial Number.

The information can be found on the rating plate.

Warning / Caution-Safety information

General information and tips

Environmental information

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance,

carefully read the supplied instructions. The

manufacturer is not responsible for any injuries or

damages that are the result of incorrect installation or

www.aeg.com

usage. Always keep the instructions in a safe and

accessible location for future reference.

1.1 Children and vulnerable people safety

• This appliance can be used by children aged from 8

years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience

and knowledge if they have been given supervision or

instruction concerning the use of the appliance in a

safe way and understand the hazards involved.

• Children between 3 and 8 years of age and persons

with very extensive and complex disabilities shall be

kept away unless continuously supervised.

• Children of less than 3 years of age should be kept

away unless continuously supervised.

• Do not let children play with the appliance.

• Keep all packaging away from children and dispose of

it appropriately.

• Keep children and pets away from the appliance when

it operates or when it cools down. Accessible parts are

hot.

• If the appliance has a child safety device, it should be

activated.

• Children shall not carry out cleaning and user

maintenance of the appliance without supervision.

1.2

General Safety

• WARNING: The appliance and its accessible parts

become hot during use. Care should be taken to

avoid touching heating elements.

• Do not operate the appliance by means of an external

timer or separate remote-control system.

• WARNING: Unattended cooking on a hob with fat or

oil can be dangerous and may result in fire.

• NEVER try to extinguish a fire with water, but switch

off the appliance and then cover flame e.g. with a lid

or a fire blanket.

ENGLISH

• CAUTION: The cooking process has to be supervised.

A short term cooking process has to be supervised

continuously.

• WARNING: Danger of fire: Do not store items on the

cooking surfaces.

• Metallic objects such as knives, forks, spoons and lids

should not be placed on the hob surface since they

can get hot.

• Do not use a steam cleaner to clean the appliance.

• If the supply cord is damaged, it must be replaced by

the manufacturer, an authorized Service or similarly

qualified persons in order to avoid a hazard.

• Where the appliance is directly connected to the

power supply, an all-pole isolating switch with a

contact gap is required. Complete disconnection in

compliance with the conditions specified in

overvoltage category III must be guaranteed. The

earth cable is excluded from this.

• When you route the mains cable, make sure that the

cable doesn't come into direct contact (for example

using insulating sleeving) with parts that can reach

temperatures of more than 50°C above room

temperature.

• WARNING: Use only hob guards designed by the

manufacturer of the cooking appliance or indicated by

the manufacturer of the appliance in the instructions

for use as suitable or hob guards incorporated in the

appliance. The use of inappropriate guards can cause

accidents.

SAFETY INSTRUCTIONS

This appliance is suitable for the

following markets: IT

2.1 Installation

WARNING!

Only a qualified person must

install this appliance.

WARNING!

Risk of injury or damage to

the appliance.

• Remove all the packaging.

• Do not install or use a damaged

appliance.

• Follow the installation instructions

supplied with the appliance.

www.aeg.com4

• Keep the minimum distance from

other appliances and units.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Seal the cut surfaces with a sealant to

prevent moisture to cause swelling.

• Protect the bottom of the appliance

from steam and moisture.

• Do not install the appliance adjacent

to a door or under a window. This

prevents hot cookware falling from

the appliance when the door or the

window is opened.

• If the appliance is installed above

drawers make sure that the space,

between the bottom of the appliance

and the upper drawer, is sufficient for

air circulation.

• The bottom of the appliance can get

hot. Make sure to install a non-

combustible separation panel under

the appliance to prevent access to the

bottom.

2.2 Electrical Connection

WARNING!

Risk of fire and electric

shock.

• All electrical connections should be

made by a qualified electrician.

• The appliance must be earthed.

• Before carrying out any operation

make sure that the appliance is

disconnected from the power supply.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Make sure the appliance is installed

correctly. Loose and incorrect

electricity mains cable or plug (if

applicable) can make the terminal

become too hot.

• Use the correct electricity mains

cable.

• Do not let the electricity mains cable

tangle.

• Make sure that a shock protection is

installed.

• Use the strain relief clamp on the

cable.

• Make sure the mains cable or plug (if

applicable) does not touch the hot

appliance or hot cookware, when you

connect the appliance to the near

sockets.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to

the mains plug (if applicable) or to the

mains cable. Contact our Authorised

Service Centre or an electrician to

change a damaged mains cable.

• The shock protection of live and

insulated parts must be fastened in

such a way that it cannot be removed

without tools.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• If the mains socket is loose, do not

connect the mains plug.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• Use only correct isolation devices: line

protecting cut-outs, fuses (screw type

fuses removed from the holder), earth

leakage trips and contactors.

• The electrical installation must have

an isolation device which lets you

disconnect the appliance from the

mains at all poles. The isolation

device must have a contact opening

width of minimum 3 mm.

2.3 Gas connection

• All gas connections should be made

by a qualified person.

• Before installation, make sure that the

local distribution conditions (nature of

the gas and gas pressure) and the

adjustment of the appliance are

compatible.

• Make sure that there is air circulation

around the appliance.

• The information about the gas supply

is on the rating plate.

• This appliance is not connected to a

device, which evacuates the products

of combustion. Make sure to connect

the appliance according to current

installation regulations. Pay attention

to requirements regarding adequate

ventilation.

ENGLISH

2.4 Use

WARNING!

Risk of injury, burns and

electric shock.

• Remove all the packaging, labelling

and protective film (if applicable)

before first use.

• Use this appliance in a household

environment.

• Do not change the specification of

this appliance.

• Make sure that the ventilation

openings are not blocked.

• Do not let the appliance stay

unattended during operation.

• Set the cooking zone to “off” after

each use.

• Do not put cutlery or saucepan lids on

the cooking zones. They can become

hot.

• Do not operate the appliance with

wet hands or when it has contact with

water.

• Do not use the appliance as a work

surface or as a storage surface.

• When you place food into hot oil, it

may splash.

WARNING!

Risk of fire and explosion

• Fats and oil when heated can release

flammable vapours. Keep flames or

heated objects away from fats and oils

when you cook with them.

• The vapours that very hot oil releases

can cause spontaneous combustion.

• Used oil, that can contain food

remnants, can cause fire at a lower

temperature than oil used for the first

time.

• Do not put flammable products or

items that are wet with flammable

products in, near or on the appliance.

WARNING!

Risk of damage to the

appliance.

• Do not keep hot cookware on the

control panel.

• Do not let cookware to boil dry.

• Be careful not to let objects or

cookware fall on the appliance. The

surface can be damaged.

• Do not activate the cooking zones

with empty cookware or without

cookware.

• Do not put aluminium foil on the

appliance.

• Use only stable cookware with the

correct shape and diameter larger

than the dimensions of the burners.

• Make sure cookware is centrally

positioned on the burners.

• Make sure the flame does not go out

when you quickly turn the knob from

the maximum to the minimum

position.

• Use only the accessories supplied

with the appliance.

• Do not install a flame diffuser on the

burner.

• The use of a gas cooking appliance

results in the production of heat and

moisture. Provide good ventilation in

the room where the appliance is

installed.

• Prolonged intensive use of the

appliance may call for additional

ventilation, for example opening of a

window, or more effective ventilation,

for example increasing the level of

mechanical ventilation where present.

• This appliance is for cooking

purposes only. It must not be used for

other purposes, for example room

heating.

• Do not let acid liquids, for example

vinegar, lemon juice or limescale

remover, touch the hob. This can

cause matt patches.

• Discoloration of the enamel or

stainless steel has no effect on the

performance of the appliance.

2.5 Care and cleaning

WARNING!

Do not remove the buttons,

knobs or gaskets from the

control panel. Water may

get inside the appliance and

cause damage.

• Clean the appliance regularly to

prevent the deterioration of the

surface material.

• Deactivate the appliance and let it

cool down before you clean it.

www.aeg.com

• Disconnect the appliance from the

electrical supply before maintenance.

• Do not use water spray and steam to

clean the appliance.

• Clean the appliance with a moist soft

cloth. Only use neutral detergents. Do

not use any abrasive products,

abrasive cleaning pads, solvents or

metal objects.

• Do not clean the burners in the

dishwasher.

2.6 Service

• To repair the appliance contact an

Authorised Service Centre.

• Use original spare parts only.

2.7 Disposal

WARNING!

Risk of injury or suffocation.

• Contact your municipal authority for

information on how to discard the

appliance correctly.

• Disconnect the appliance from the

mains supply.

• Cut off the mains electrical cable

close to the appliance and dispose of

it.

• Flat the external gas pipes.

3. INSTALLATION

WARNING!

Refer to Safety chapters.

3.1 Before the installation

Before you install the hob, write down

the information bellow from the rating

plate. The rating plate is on the bottom

of the hob.

Model .......................................

PNC .........................................

Serial number ...........................

3.2 Gas Connection

WARNING!

The following instructions

about installation,

maintenance and ventilation

must be carried out by

qualified personnel in

compliance with the

regulation in force (UNI-CIG

7129 - 7131). Make sure that

the kitchen is well ventilated:

keep natural ventilation

holes open (at least 100 cm²)

or install a mechanical

extractor hood.

Choose fixed connections or use a

flexible pipe in stainless steel in

compliance with the regulation in force.

If you use flexible metallic pipes, be

careful they do not come in touch with

mobile parts or they are not squeezed.

Also be careful when the hob is put

together with an oven.

Make sure that the gas

supply pressure of the

appliance obeys the

recommended values.

If the supplied pressure has not the

specified value, it is necessary to

assemble a proper pressure regulator in

compliance with the standard UNI EN 88.

For Liquid Gas (LPG) the use of pressure

regulator is allowed only if they are in

compliance with UNI EN 12864. The

adjustable connection is fixed to the

comprehensive ramp by means of a

threaded nut G 1/2". Screw the parts

without force, adjust the connection in

the necessary direction and tighten

everything.

A B C

A. End of shaft with nut

B. Washer supplied with the appliance

C. Elbow supplied with the appliance

ENGLISH

Rigid connection:

Carry out connection by using metal rigid

pipes (copper with mechanical end) (UNI-

CIG 7129).

Flexible connection:

Use a flexible pipe in stainless steel (UNI-

CIG 9891) with a maximum length 2 m.

WARNING!

When installation is

complete, make sure that

the seal of each pipe fitting

is correct. Use a soapy

solution, not a flame!

3.3 Injectors replacement

1. Remove the pan supports.

2. Remove the caps and crowns of the

burner.

3. With a socket spanner 7 remove the

injectors and replace them with the

ones which are necessary for the type

of gas you use (see table in

"Technical Data" chapter).

4. Assemble the parts, follow the same

procedure backwards.

5. Replace the rating plate (it is near the

gas supply pipe) with the one for the

new type of gas supply. You can find

this plate in the package supplied

with the appliance.

If the supply gas pressure is changeable

or different from the necessary pressure,

you must fit an applicable pressure

adjuster on the gas supply pipe.

3.4 Adjustment of minimum

level

To adjust the minimum level of the

burners:

1. Light the burner.

2. Turn the knob on the minimum

position.

3. Remove the knob .

4. With a thin screwdriver, adjust the

bypass screw position (A).

If you change:

• from natural gas G20 20 mbar to

liquid gas, fully tighten the bypass

screw in.

• from liquid gas to natural gas G20

20 mbar, undo the bypass screw

approximately 1/4 of a turn (1/2 of

a turn for Triple Crown burner).

WARNING!

Make sure the flame does

not go out when you quickly

turn the knob from the

maximum position to the

minimum position.

3.5 Electrical connection

• Make sure that the rated voltage and

type of power on the rating plate

agree with the voltage and the power

of the local power supply.

• This appliance is supplied with a

mains cable. It has to be supplied with

a correct plug which can hold the load

that the rating plate rates. Make sure

that you install the plug in a correct

socket.

• Always use a correctly installed

shockproof socket.

• Make sure that there is an access to

the mains plug after the installation.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• There is a risk of fire when the

appliance is in connection with an

extension cable, an adapter or a

multiple connection. Make sure that

the ground connection agrees with

the standards and regulations.

• Do not let the power cable to heat up

to a temperature higher than 90° C.

To prevent contact between the cable

and the appliance below the hob use the

clamps which are on the side of the

cabinet.

www.aeg.com

A. Rigid copper pipe or flexible pipe of

stainless steel

3.6 Connection cable

To replace the connection cable use only

the special cable or its equivalent. The

cable type is: H05V2V2-FT90.

Make sure that the cable section is

applicable to the voltage and the

working temperature. The yellow / green

earth wire must be approximately 2 cm

longer than the brown (or black) phase

wire.

3.7 Assembly

min.

55 mm

min.

650 mm

560 mm

480 mm

min.

450 mm

30 mm

A) supplied seal

B) supplied brackets

ENGLISH

CAUTION!

Install the appliance only on

a worktop with flat surface.

3.8 Installing hob under the

hood

If you install the hob under a

hood, please see the

installation instructions of

the hood for the minimum

distance between the

appliances.

3.9 Possibilities for insertion

The panel installed below the hob must

be easy to remove and let an easy access

in case a technical assistance

intervention is necessary.

Kitchen unit with door

min 20 mm

(max 150 mm)

30 mm

60 mm

A. Removable panel

B. Space for connections

Kitchen unit with oven

The electrical connection of the hob and

the oven must be installed separately for

safety reasons and to let easy remove

oven from the unit.

4. PRODUCT DESCRIPTION

4.1 Cooking surface layout

Semi-rapid burner

Triple Crown burner

Auxiliary burner

Control knobs

4.2 Control knob

Symbol Description

no gas supply / off posi-

tion

Symbol Description

ignition position / maxi-

mum gas supply

minimum gas supply

www.aeg.com10

5. DAILY USE

WARNING!

Refer to Safety chapters.

5.1 Burner overview

A. Burner cap and crown

B. Thermocouple

C. Ignition candle

A. Burner cap

B. Burner crown

C. Ignition candle

D. Thermocouple

5.2 Ignition of the burner

Always light the burner

before you put on the

cookware.

WARNING!

Be very careful when you use

open fire in the kitchen

environment. The

manufacturer declines any

responsibility in case of the

flame misuse.

1. Push the control knob down and turn

it counterclockwise to the maximum

gas supply position ( ).

2. Keep the control knob pushed for

equal or less than 10 seconds. This

lets the thermocouple warm up. If

not, the gas supply is interrupted.

3. Adjust the flame after it is regular.

If after some tries the burner

does not light, check if the

crown and its cap are in

correct positions.

WARNING!

Do not keep the control

knob pushed for more than

15 seconds. If the burner

does not light after 15

seconds, release the control

knob, turn it into off position

and try to light the burner

again after minimum 1

minute.

CAUTION!

In the absence of electricity

you can ignite the burner

without electrical device; in

this case approach the

burner with a flame, turn the

control knob counter-

clockwise to maximum gas

supply position and push it

down. Keep the control

knob pushed for equal or

less than 10 seconds to let

the thermocouple warm up.

ENGLISH 11

If the burner accidentally

goes out, turn the control

knob to the off position and

try to light the burner again

after minimum 1 minute.

The spark generator can

start automatically when you

switch on the mains, after

installation or a power cut. It

is normal.

The hob is supplied with the

progressive valves. They

make the flame regulation

more precise.

5.3 Turning the burner off

To put the flame out, turn the knob to

the off position .

WARNING!

Always turn the flame down

or switch it off before you

remove the pans from the

burner.

6. HINTS AND TIPS

WARNING!

Refer to Safety chapters.

6.1 Cookware

CAUTION!

Do not use cast iron pans,

clay or earthenware pots,

grill or toaster plates. The

stainless steel can become

tarnished if it is too much

heated.

WARNING!

Do not put the same pan on

two burners.

WARNING!

Do not put unstable or

damaged pots on the burner

to prevent spills and injuries.

CAUTION!

Make sure that the bottoms

of pots do not stand too

close to the control knob,

otherwise the flame heats

the control knob up.

CAUTION!

Make sure that pot handles

are not above the front edge

of the cooktop.

CAUTION!

Make sure that the pots are

placed centrally on the

burner in order to get the

maximum stability and a

lower gas consumption.

6.2 Diameters of cookware

Use cookware with

diameters applicable to the

size of burners.

Burner Diameter of

cookware (mm)

Triple Crown 180 - 260

Semi-rapid (rear left) 120 - 240

Semi-rapid (rear right) 120 - 240

Semi-rapid (front left) 120 - 220

Auxiliary 80 - 180

www.aeg.com12

7. CARE AND CLEANING

WARNING!

Refer to Safety chapters.

7.1 General information

• Clean the hob after each use.

• Always use cookware with a clean

base.

• Scratches or dark stains on the surface

have no effect on how the hob

operates.

• Use a special cleaner suitable for the

surface of the hob.

Stainless steel

• Wash stainless steel parts with water,

and then dry them with a soft cloth.

• To remove burnt food, fat and

stubborn stains let them soak in a

small amount of mild detergent for a

few minutes before cleaning.

• Use cleaning products designed

specifically for cleaning stainless steel

in order to protect the steel surfaces.

• Do not use cleaning products

containing corrosive chemicals such

as chlorides, do not clean the surface

with disinfectants, stain or rust

removers and immersion cleaners.

7.2 Pan supports

The pan supports are not

resistant to washing in a

dishwasher. They must be

washed by hand.

1. Remove the pan supports to easily

clean the hob.

Be very careful when you

replace the pan supports

to prevent the hob top

from damage.

2. The enamel coating occasionally can

have rough edges, so be careful

when you wash the pan supports by

hand and dry them. If necessary,

remove stubborn stains with a paste

cleaner.

3. After you clean the pan supports,

make sure that they are in correct

positions.

4. For the burner to operate correctly,

make sure that the arms of the pan

supports are .

7.3 Cleaning the hob

• Remove immediately: melted plastic,

plastic foil, sugar and food with sugar,

otherwise, the dirt can cause damage

to the hob. Take care to avoid burns.

• Remove when the hob is sufficiently

cool: limescale rings, water rings, fat

stains, shiny metallic discoloration.

Clean the hob with a moist cloth and

a non-abrasive detergent. After

cleaning, wipe the hob dry with a soft

cloth.

• To clean the enamelled parts, caps

and crowns, wash them with warm

soapy water and dry them carefully

before you put them back on.

7.4 Cleaning the spark plug

This feature is obtained through a

ceramic ignition candle with a metal

electrode. Keep these components well

clean to prevent difficult lighting and

check that the burner crown holes are

not obstructed.

7.5 Periodic maintenance

Speak to your local Authorised Service

Centre periodically to check the

conditions of the gas supply pipe and

the pressure adjuster, if fitted.

TROUBLESHOOTING

WARNING!

Refer to Safety chapters.

ENGLISH 13

8.1 What to do if...

Problem Possible cause Remedy

There is no spark when you

try to activate the spark gen-

erator.

The hob is not connected to

an electrical supply or it is

connected incorrectly.

Check if the hob is correctly

connected to the electrical

supply.

The fuse is blown. Make sure that the fuse is

the cause of the malfunction.

If the fuse is blown again

and again, contact a quali-

fied electrician.

Burner cap and crown are

placed incorrectly.

Place the burner cap and

crown correctly.

The flame extinguishes im-

mediately after ignition.

Thermocouple is not heated

up sufficiently.

After lightning the flame,

keep the knob pushed for

equal or less than 10 sec-

onds.

The flame ring is uneven. Burner crown is blocked with

food residues.

Make sure that the injector is

not blocked and the burner

crown is clean.

8.2 If you cannot find a

solution...

If you cannot find a solution to the

problem yourself, contact your dealer or

an Authorised Service Centre. Give the

data from the rating plate. Make sure,

you operated the hob correctly. If not the

servicing by a service technician or

dealer will not be free of charge, also

during the warranty period. The

instructions about the Service Centre and

conditions of guarantee are in the

guarantee booklet.

www.aeg.com14

8.3 Labels supplied with the

accessories bag

Stick the adhesive labels as indicated

below:

MOD.

PROD.NO.

SER.NO

DATA

MOD.

PROD.NO.

SER.NO

DATA

MOD.

PROD.NO.

SER.NO.

03 IT

MADE IN ITALY

TYPE

IP20

0049

A B C

A. Stick it on Guarantee Card and send

this part (if applicable).

B. Stick it on Guarantee Card and keep

this part (if applicable).

C. Stick it on instruction booklet.

9. TECHNICAL DATA

9.1 Hob dimensions

Width 745 mm

Depth 515 mm

9.2 Bypass diameters

BURNER Ø BYPASS 1/100 mm

Triple Crown 57

Semi-rapid 32

Auxiliary 28

ENGLISH 15

9.3 Other technical data

TOTAL POWER:

Gas original: G20 (2H) 20 mbar 11,0 kW

Gas replace-

ment:

G30 (3+) 28-30 mbar 800 g/h

G31 (3+) 37 mbar 786 g/h

Electric supply: 220-240 V ~ 50/60 Hz

Appliance cate-

gory:

II2H3+

Gas connection: G 1/2"

Appliance class: 3

9.4 Gas burners for NATURAL GAS G20 20 mbar

BURNER NORMAL POWER

MINIMUM POWER

INJECTOR MARK

Triple Crown 4,0 1,4 146

Semi-rapid 2,0 0,45 96

Auxiliary 1,0 0,33 70

9.5 Gas burners for LPG G30/G31 28-30/37 mbar

BURNER NORMAL

POWER kW

MINIMUM

POWER kW

INJECTOR

MARK

NOMINAL GAS FLOW g/h

G30 28-30

mbar

G31 37 mbar

Triple Crown 4,0 1,4 98 291 286

Semi-rapid 2,0 0,45 71 145 143

Auxiliary 1,0 0,33 50 73 71

10. ENERGY EFFICIENCY

10.1 Product information according to EU 66/2014

Model identification HG755421UM

Type of hob Built-in hob

Number of gas burners 5

www.aeg.com16

Energy efficiency per gas burner

(EE gas burner)

Left rear - Semi-rapid 57.8%

Right rear - Semi-rapid 57.8%

Middle - Triple Crown 52.0%

Left front - Semi-rapid 57.8%

Right front - Auxiliary not applicable

Energy efficiency for the gas hob

(EE gas hob)

56.3%

EN 30-2-1: Domestic cooking appliances burning gas - Part 2-1 : Rational use of

energy - General

10.2 Energy saving

• Before use, make sure that the burners and pan supports are assembled correctly.

• Use cookware with diameters applicable to the size of burners.

• Center the pot on the burner.

• When you heat up water, use only the amount you need.

• If it is possible, always put the lids on the cookware.

• When the liquid starts to boil, turn down the flame to barely simmer the liquid.

• If it is possible, use a pressure cooker. Refer to its user manual.

11. ENVIRONMENTAL CONCERNS

Recycle materials with the symbol .

Put the packaging in relevant containers

to recycle it. Help protect the

environment and human health by

recycling waste of electrical and

electronic appliances. Do not dispose of

appliances marked with the symbol

with the household waste. Return the

product to your local recycling facility or

contact your municipal office.

ENGLISH 17

TABLE DES MATIÈRES

1. INFORMATIONS DE SÉCURITÉ...............................................................................18

2. CONSIGNES DE SÉCURITÉ......................................................................................21

3. INSTALLATION..........................................................................................................23

4. DESCRIPTION DE L'APPAREIL.................................................................................27

5. UTILISATION QUOTIDIENNE.................................................................................. 28

6. CONSEILS.................................................................................................................. 29

7. ENTRETIEN ET NETTOYAGE...................................................................................30

8. EN CAS D'ANOMALIE DE FONCTIONNEMENT.................................................. 31

9. CARACTÉRISTIQUES TECHNIQUES....................................................................... 33

10. RENDEMENT ÉNERGÉTIQUE............................................................................... 34

POUR DES RÉSULTATS PARFAITS

Merci d'avoir choisi ce produit AEG. Nous l'avons conçu pour qu'il vous offre des

performances irréprochables pour longtemps, en intégrant des technologies

innovantes qui vous simplifient la vie grâce à des caractéristiques que vous ne

trouverez pas forcément sur des appareils ordinaires. Veuillez prendre quelques

instants pour lire cette notice afin d'utiliser au mieux votre appareil.

Visitez notre site Internet pour :

Obtenir des conseils d'utilisation, des brochures, de l'aide, des informations :

www.aeg.com/webselfservice

Enregistrez votre produit pour obtenir un meilleur service :

www.registeraeg.com

Acheter des accessoires, consommables et pièces de rechange d'origine pour

votre appareil :

www.aeg.com/shop

SERVICE APRÈS-VENTE

Utilisez toujours des pièces d'origine.

Avant de contacter le service après-vente, assurez-vous de disposer des

informations suivantes : Modèle, PNC, numéro de série.

Vous trouverez ces informations sur la plaque signalétique.

Avertissement/Consignes de sécurité

Informations générales et conseils

Informations en matière de protection de l'environnement

Sous réserve de modifications.

INFORMATIONS DE SÉCURITÉ

Avant d'installer et d'utiliser cet appareil, lisez

soigneusement les instructions fournies. Le fabricant ne

pourra être tenu pour responsable des blessures et

dégâts résultant d'une mauvaise installation ou

www.aeg.com

utilisation. Conservez toujours les instructions dans un

lieu sûr et accessible pour vous y référer ultérieurement.

1.1 Sécurité des enfants et des personnes

vulnérables

• Cet appareil peut être utilisé par des enfants de plus

de 8 ans, ainsi que des personnes dont les capacités

physiques, sensorielles et mentales sont réduites ou

dont les connaissances et l'expérience sont

insuffisantes, à condition d'être surveillés ou d'avoir

reçu des instructions concernant l'utilisation sécurisée

de l'appareil et de comprendre les risques encourus.

• Les enfants entre 3 et 8 ans et les personnes ayant un

handicap très important et complexe doivent être

tenus à l'écart, à moins d'être surveillés en

permanence.

• Les enfants de moins de 3 ans doivent être tenus à

l'écart, à moins d'être surveillés en permanence.

• Ne laissez pas les enfants jouer avec l'appareil.

• Ne laissez pas les emballages à la portée des enfants

et jetez-les convenablement.

• Tenez les enfants et les animaux éloignés de l'appareil

lorsqu'il est en cours de fonctionnement ou lorsqu'il

refroidit. Les parties accessibles sont chaudes.

• Si l'appareil est équipé d'un dispositif de sécurité

enfants, nous vous recommandons de l'activer.

• Les enfants ne doivent pas nettoyer ni entreprendre

une opération de maintenance sur l'appareil sans

surveillance.

1.2

Sécurité générale

• AVERTISSEMENT : L'appareil et ses parties

accessibles deviennent chauds pendant son

fonctionnement. Veillez à ne pas toucher les éléments

chauffants.

• Ne faites pas fonctionner l'appareil avec un minuteur

externe ou un système de commande à distance.

FRANÇAIS

• AVERTISSEMENT : Il peut être dangereux de laisser

chauffer de la graisse ou de l'huile sans surveillance

sur une table de cuisson car cela pourrait provoquer

un incendie.

• N'essayez JAMAIS d'éteindre un feu avec de l'eau.

Éteignez l'appareil puis couvrez les flammes, par

exemple avec un couvercle ou une couverture

ignifuge.

• ATTENTION : Toute cuisson doit être surveillée. Une

cuisson courte doit être surveillée en permanence.

• AVERTISSEMENT : Risque d'incendie : N'entreposez

rien sur les surfaces de cuisson.

• Ne posez pas d'objets métalliques tels que couteaux,

fourchettes, cuillères ou couvercles sur la table de

cuisson car ils pourraient chauffer.

• N'utilisez pas de nettoyeur vapeur pour nettoyer

l'appareil.

• Si le câble d'alimentation est endommagé, il doit être

remplacé par le fabricant, un service de maintenance

agréé ou un technicien qualifié afin d'éviter tout

danger.

• Si l'appareil est relié directement à l'alimentation

électrique, installez un sectionneur avec une ouverture

de contact. Il est indispensable de garantir une

déconnexion complète conformément aux conditions

de surtension de catégorie III. Le fil de terre n'est pas

concerné.

• Lorsque vous acheminez le câble d'alimentation,

assurez-vous qu'il n'entre pas en contact direct (par

exemple, à l'aide d'un manchon isolant) avec des

parties pouvant atteindre des températures

supérieures de 50 °C à la température ambiante.

• AVERTISSEMENT : Utilisez uniquement les dispositifs

de protection pour table de cuisson conçus ou

indiqués comme adaptés par le fabricant de l'appareil

de cuisson dans les instructions d'utilisation, ou les

dispositifs de protection pour table de cuisson

www.aeg.com

La page charge ...

AEG HG755421UM Manuel utilisateur

Marque: AEG

Modèle: HG755421UM

Catégorie: Plaques de cuisson

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: AEG HG755421UM User manual

Documents connexes

Autres documents

Zanussi ZGO78520BA Manuel utilisateur