AR Blue Clean BC111HS Le manuel du propriétaire

Catégorie
Nettoyeurs haute pression
Taper
Le manuel du propriétaire
1600 PSI
Electric Pressure Washer
ASSEMBLY, CARE AND
USE INSTRUCTIONS
Model BC111HS
READ CAREFULLY
IMPORTANT: RETAIN THESE INSTRUCTIONS
AND ATTACH RECEIPT TO MANUAL FOR FUTURE
REFERENCE.
95497-DK
Questions, problems, missing parts?
Before returning to your retailer, call (1-866-235-5112)
or email (info@arnorthamerica.com) our customer
service department. They are available from 8:00 a.m. -
5:00 p.m., CST, Monday - Friday. www.arblueclean.com
WARNING: This product can expose you to
chemicals including lead, DEHP, DINP, which is
known to the State of California to cause cancer
and or lead to birth defects. For more information
go to www.P65Warnings.ca.gov
2
THANK YOU LETTER
Dear Valued Customer,
My name is Michael Schaller and I wanted to thank you on behalf of AR Blue Clean for purchasing
this AR Blue Clean electric pressure washer. We created this pressure washer from listening to
our customers for the past 10 years on how they use their pressure washer for all kinds of cleaning
projects.
I am excited to tell you that this pressure washer has a 2-year warrantyFirst year of the warranty
completely covers anything that may happen to it during this time. The second year of the warranty
only covers manufacturer defects. If you have any concerns or questions, please contact us at
866-235-5112 or ARBLUECLEAN.COM where you can email or chat with us. Our friendly customer
service team based here in Fridley, MN can help you with just about anything.
Lastly I would like to ask a favor, please take a moment to review this pressure washer from the place
you purchased it. I look forward to reading your comments.
Thank you and happy cleaning!
Michael Schaller
Product Manager
AR North America Inc.
140 81st Ave. NE Fridley, MN 55432
651.274.2455 cell
763.398.6091 ofce
3
Product Specications ...................................................................................................... 3
Package Contents ............................................................................................................. 4
Hardware Contents ........................................................................................................... 4
Safety Information ............................................................................................................. 5
Assembly Instructions ....................................................................................................... 7
Operating Instructions .....................................................................................................11
Care and Maintenance ................................................................................................... 13
Pump Saver ..................................................................................................................... 14
Troubleshooting ............................................................................................................... 15
Limited Warranty ............................................................................................................. 16
Replacement Parts List .................................................................................................. 17
TABLE OF CONTENTS
SPECIFICATIONS
Model
Max PSI
(lbs/sq. in.)
Rated PSI
(lbs/sq. in.)
Max GPM
(Gal/per min)
Rated GPM
(Gal/per min)
Cold
Water
Volts Frequency
(Hz)
Amps Weight
(lbs.)
BC111HS 1600 1160 1.7 1.2 120 60 12.5 14.6
PRODUCT SPECIFICATIONS
4
PACKAGE CONTENTS
HARDWARE CONTENTS
PART DESCRIPTION QUANTITY
H Foam Cannon 1
I Extension Lance 1
J 15° Quick Connect Nozzle 1
K O-Ring Kit 1
L Nozzle Cleaning Wire 1
AA Screws 2
PART DESCRIPTION QUANTITY
A Spray Gun Holster 1
B Handle 1
C Power Washer Unit 1
D Cord Hook 1
E Super Soft High Pressure Hose 1
F Spray Gun 1
G Spray Gun Lock/Unlock 1
OFF/O
ON/I
E
B
C
L
A
DK
AA
PW95824
J
I
F
G
H
750ml
600ml
450ml
300ml
150ml
15° – Yellow
AA
Screws
Qty. 2
Note: Screws are located in
manual package.
5
SAFETY INFORMATIONSAFETY INFORMATION
Please read and understand this entire manual before
attempting to assemble and operate the product.
This manual contains information that relates to
PROTECTING PERSONAL SAFETY and PREVENTING
EQUIPMENT PROBLEMS. It is very important to read this
manual carefully and understand it thoroughly before
using the product. The symbols listed below are used to
indicate this information.
DANGER
Potential hazard that will result in serious injury or
loss of life.
WARNING
Hazard that could result in serious injury or loss of
life.
CAUTION
Potential hazard that may result in moderate injury
or damage to equipment.
Note: The word “Note” is used to inform the reader of
something the operator needs to know about the tool.
WARNING
To reduce the risk of injury, the user must read
and understand the instructions before using
this product.
1. Warning – When using this product, basic
precautions should always be followed, including the
following.
2. Read all the instructions before using the product.
3. Know how to stop the product and bleed pressures
quickly. Be thoroughly familiar with the controls.
4. Keep operating area clear of persons.
5. Do not overreach or stand on unstable support. Keep
good footing and balance at all times.
6. Follow the maintenance instructions as specied in
the manual.
7. To avoid personal injury and/or damage to property
and to maximize your power washer experience,
carefully follow all of the safety tips, instructions,
warnings and safeguards and become familiar with
all of the controls. Be sure you know how to quickly
bleed off the pressure from all parts of your power
washer and how to turn off the power washer.
8. This power washer conforms to CSA and other safety
and consumer standards. DO NOT modify or rebuild
any part of your power washer.
9. DO NOT use your power washer when you are under
the inuence of alcohol or drugs. Use this power tool
carefully and only when you are alert.
10. Watch your balance and footing while using your
power washer. Surfaces become slippery when wet
and are extra slippery when using a detergent or
cleaner.
11. NEVER operate the power washer in bare feet,
sandals, or open-toed shoes.
12. When using the power washer near children, make
sure they are closely supervised by an adult to avoid
injury. NEVER let a child use the power washer.
13. Keep ngers, hands, feet and any part of your body
clear of the stream of high pressure water. The
powerful spray can cause blindness or blast holes in
the skin. It can break a window if you are too close
when you pull the trigger on the spray gun.
14. ALWAYS wear eye protection to prevent injury to
eyes when operating the power washer.
15. To avoid mishaps or injury, ALWAYS use the trigger
safety lock when not using the power washer even if
only stopping briey.
16. The power washer is equipped with a Ground Fault
Circuit Interrupter (GFCI) which greatly reduces the
chance of electric shock while the unit is in use. If
replacement of the plug or cord is needed, use only
identical replacement parts.
17. Point the spray gun in a safe direction when
beginning a power washer session.
18. Warning- NEVER spray directly at a person, animal,
electrical device or the unit itself.
19. When rst using the spray gun, hold the spray gun
and lance with two hands when pulling the trigger
(one hand to pull the trigger and the other to
stabilize the gun assembly) until you get used to the
“kickback” from the spray gun.
20. When you turn the power switch off, water pressure
may remain in the system. To discharge the
pressure, point the spray gun in a safe direction and
pull the trigger.
21. NEVER spray ammable liquids.
22. NEVER use the power washer in areas that contain
combustible dust, liquids or vapors.
23. Avoid contact of the pressure hose with sharp
objects and examine the hose regularly. Replace
if damaged. Due to the high pressure involved, it
cannot be repaired if cut or damaged.
24. Only use detergent specically formulated for power
washers and follow instructions on the detergent’s
label. Dish or laundry soap is too thick and will
clog the nozzle of your foam cannon.
6
Servicing of a Double-Insulated Appliance
Ground Fault Circuit Interrupter Protection:
This pressure washer is equipped with a ground-fault
circuit-interrupter (GFCI) built into the plugs of the
power-supply cord. This device provides additional
protection from the risk of electric shock. Should
replacement of the plug or cord become necessary,
use only identical replacement parts that include GFCI
protection.
In a double-insulated product, two systems of insulation
are provided instead of grounding. Grounding means
are not provided for a double insulated product, nor
should grounding means be added to the product.
Servicing a double-insulated product requires extreme
care and knowledge of the system, and should only be
done by qualied service personnel.
Replacement parts for a double-insulated product must
be identical to the original parts.
A double-insulated product is marked with the words
“Double Insulation” or “Double Insulated”. Product may
also be marked with symbol shown here.
SAFETY INFORMATIONSAFETY INFORMATION
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
25. Protect eyes, lungs, and skin from exposure to
detergent.
26. Warning-If connection is made to a potable water
system, the system Should be protected against
backow.
CAUTION
Store the power washer indoors to prevent the
water in the unit from expanding under freezing
conditions. When the water freezes and expands,
your power washer will be damaged and become
inoperable. Or, if storing outdoors, it is
recommended you use pump saver (not included)
to protect pumps.
27. NEVER use hot water with your power washer. It will
overheat and damage the high pressure pump.
28. NEVER leave the power washer unattended while it
is powered “ON”.
29. ALWAYS turn the water supply on before turning the
power washer power to on. Running the pump dry
will cause damage to the internal components.
30. NEVER use a water supply to your power washer
that exceeds 150 PSI maximum.
31. NEVER disconnect the high pressure hose from the
power washer while the system is pressurized.
32. NEVER permanently engage the trigger mechanism
on the spray gun.
33. NEVER operate the power washer unless all
components are properly and securely connected.
34. NEVER allow the power washer pump to run for
more than one minute after you have turned off the
water supply. This can cause the motor and pump to
overheat and fail.
35. NEVER use lances or other parts that are not
compatible for this specic AR Blue Clean unit.
36. NEVER use an extension power cord since it defeats
the effectiveness of the GFCI and increases the
chance of electrocuting the operator.
37. NEVER spray any electrical outlet with your power
washer.
38. Inspect the power cord before using. DO NOT use it
if it is damaged.
39. Stay alert - watch what you are doing.
Double Insolated Product
7
Before beginning assembly of product, make sure all
parts are present. Compare parts with package contents
list and hardware contents list. If any part is missing or
damaged, DO NOT attempt to assemble the product.
Please call customer service at 1-866-235-5112.
Replacement parts will be sent no charge.
Estimated Assembly Time: 5 minutes.
Tools Required for Assembly (not included): Phillips
screwdriver.
ASSEMBLY INSTRUCTIONS
Power Unit Assembly
Install handle (B) to power washer unit (C).
Secure with screws (AA).
Note: DO NOT use a power screwdriver. When the
screw is completely tight, give a small nal clockwise
twist of the screwdriver. DO NOT overtighten.
1
C
B
AA
Screws x 2
AA
AA
Screw
Qty. 2
OFF/O
ON/I
2
C
A
Slide spray gun holster (A) onto left side, when facing
the power washer unit (C) as shown.
Note: This step does not require any screws.
Hardware Used:
PREPARATIONPREPARATION
8
OFF/O
ON/I
C
3
C
D
Slide cord hook holster (D) onto right side, when facing
the power washer unit (C) as shown.
Note: This step does not require any screws.
4
C
E
Super Soft High Pressure Hose Assembly
Screw Super Soft high pressure hose (E) clockwise onto
bottom front of power washer unit (C). Pull back collar
and insert o-ring post into water outlet far enough so
collar can thread onto outlet threads until hand tight.
If it takes fewer than six turns you have not properly
tightened the Super Soft high pressure hose tting. It
is easier to position the power washer in front of you to
ensure that the threads are started correctly. Failure
to properly tighten Super Soft high pressure hose will
result in the hose slipping or popping off immediately
upon turning unit on. Do not worry about damage if this
occurs–just reinstall and take extra care when screwing
on the Super Soft high pressure hose tting.
Note: DO NOT use pliers or locking pliers to tighten.
5
E
F
Connect the other end of Super Soft high pressure hose
(E) to spray gun (F) by inserting the silver metal tip of
Super Soft high pressure hose into the tting just ahead
of trigger guard. It will lock into spray gun with a “click”.
Conrm hose is locked into spray gun by slightly pulling
on hose. The hose is now securely attached to spray
gun.
Note: DO NOT press button on underside of gun when
connecting hose to gun. This is the hose release button,
and hose will be unable to connect.
2
1
6
E
F
To release hose (E) from spray gun (F), press button on
underside of gun toward trigger guard. The hose will
slide out from connection.
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
9
9
ASSEMBLY INSTRUCTIONS
Attach nozzle (J) into end of lance (I) by pressing
selected nozzle into place. It will make a “click” sound
when rmly in place.
Note: Always turn the safety lock dial to lock trigger
when changing lances and nozzles to ensure that they
do not accidentally eject with force during removal.
Locking Spray Gun (Before Lance Installation)
To lock trigger of spray gun (F), point gun away
from you and turn dial to lock (“3” and “9” position).
Squeeze or pull trigger to make sure it is locked.
ALWAYS leave in locked position when not in
use. This ensures the gun is in “safe” mode until it
is ready for use. Turn dial to unlock (“12” and “6”
position) to release spray gun trigger.
Note: The trigger lock prevents trigger from being
accidentally engaged.
7
F
Unlocked Locked
1
2
8
I
F
Extension Lance Installation
With spray gun (F) in locked position, attach extension
lance (I) directly to spray gun. Insert lance extension
into gun, pushing together and turning clockwise
simultaneously. Turn the extension collar clockwise
to lock into place. To remove extension lance (I), turn
extension collar counterclockwise to unlock, then push
together and turn counterclockwise to release.
Note: The extension lance must be inserted in gun
before using any of the other attachments, and
in place for storage. It is recommended that once
extension is connected to leave it in place.
9
I
J
1
2
10
I
J
To remove nozzle (J) pull back on collar of lance (I) and
pull out nozzle.
10
14
C
Attach a standard garden hose to the black collar of the
garden hose adapter located on the back of the power
washer unit (C). The water is now connected to your
power washer.
Note: Flush out garden hose before connecting to
garden hose adapter.
ASSEMBLY INSTRUCTIONS
11
1
750ml
600ml
450ml
300ml
150ml
2
H
1
F
H
12
2
13
750ml
600ml
450ml
300ml
150ml
C
H
Insert foam cannon (H) into spray gun (F), push in and
turn clockwise.
Note: Always lock spray gun when changing the foam
cannon to ensure it does not eject with force.
Foam Cannon Installation
The foam cannon comes with a straw which is tted
into high pressure top. If you do not see the straw,
look inside the foam cannon and attach it to the high
pressure top. When using foam cannon, ll it with a
properly formulated detergent or cleaner with a water
ratio according to instructions on the container.
• Pressure washer detergents are recommended. See
page 13 for more information.
DO NOT use thick or gel-like detergents as they will
clog the foam cannon and can cause damage.
Foam Cannon Storage
Store the foam cannon (H) on the back of the power
washer unit (C).
ASSEMBLY INSTRUCTIONS
11
Make sure the “ON/OFF” switch is in the “OFF”
position. The power switch has international symbols
for ‘on’ and ‘off’: On (|) Off (O).
Unwind the power cord completely and plug the GFCI
into a grounded 120 volt outlet.
Turn on water supply at the faucet to completely
open.
Release safety push trigger lock up and back into
trigger. While pointing the spray gun in a safe
direction, squeeze the trigger on the spray gun until
there is a steady stream of water, letting the water
and air out of the hose. Push trigger lock back down
to lock back into place.
Turn the power switch to the “ON” (|) position. The
unit will turn on for 1 - 2 seconds and shut off. This is
a normal function of the auto start feature.
Begin power washing by squeezing the trigger on the
spray gun all the way into the handle.
Release the spray gun trigger to stop the power
washer.
Allow the motor to come to a complete stop before
squeezing the trigger again.
Squeezing and releasing the trigger rapidly will
cause the auto start feature to miss an on/off cycle
that may prevent it from working properly. Use slow
deliberate trigger pulls to avoid such symptoms.
OPERATING INSTRUCTIONS
OFF/0
ON/I
OFF/0
ON/I
Always test a small area to avoid chance of
damaging the surface.
12
OPERATING INSTRUCTIONSOPERATING INSTRUCTIONS
Operation Tips
Note: Test the GFCI before each use:
1. Plug GFCI into power outlet. Indicator should turn
green to show that cord has power.
2. Press test button, green indicator should turn off
to verify that GFCI cut off power to the cord.
3. Press reset button – green indicator should turn
on to show that cord has power again.
4. When GFCI is working properly, green indicator
will turn on when power is applied. If green
indicator turns off, it has detected electric
leakage and the GFCI cut off power to the
appliance.
If you hear the motor run intermittently when the
trigger is not being squeezed, that is normal. The
pump is priming itself so it is ready to operate when
the trigger is squeezed. Turn off the power washer if
not being used after ve minutes.
The o-rings on the bayonet end of the nozzle should
be cleaned regularly and lubricated with non-water
soluble grease such as petroleum jelly.
Keep the nozzle cleaning wire for use in unclogging
the nozzle. If you lose the cleaning wire, a
straightened paper clip also works.
How to Avoid Damaging Surfaces
Damage to surfaced being cleaned occurs because
the impact force of the water pressure exceeds
the durability of the surface. Bare wood can be
penetrated, paint can be peeled off, etc. You can vary
the force of your power washer by controlling:
1. The angle of the surface being cleaned.
2. The distance of the nozzle from the surface being
cleaned.
NEVER use a narrow high pressure stream of water
on soft surfaces susceptible to damage.
Adjusting Soap Levels on Foam Cannon
Twist knob to adjust the level of soap as indicated on
the top of the Foam Cannon (H). Twist toward the higher
concentration of bubbles for more soap, or the opposite
direction for less.
Detergents
Use detergents designed for power washers. These
can be purchased online at our website www.
arblueclean.com. Hardware stores or home centers
also have power washer detergents for different
cleaning projects. The cleaning solution should be the
consistency of water in order to prevent clogging your
detergent bottle and nozzle.
This system applies detergent under low pressure.
The cleaning power of the detergents is enhanced
when applied with low pressure and enough time is
given to break down dirt and grime. The combination
of low pressure and chemical action is very effective
and can be better than scrubbing if applied properly.
ALWAYS spray detergent on a dry surface. DO NOT
pre-soak area. Wetting the surface rst dilutes the
detergent and reduces its cleaning ability. DO NOT
allow detergent to dry on surface. On vertical surfaces
being cleaned, apply detergent to lower surfaces and
work your way up to prevent detergent from causing
streaks in the dirt and grime. Rinse detergent by
pressure washer from bottom up for same reason.
If a stain is particularly tough, it may be necessary
to reapply the detergent and use a bristled brush to
scrub the stain. Power washing after brushing should
successfully clear the stain.
H
F
13
CARE AND MAINTENANCE
Cleaning Garden Hose Adapter
The screen inside the adapter should be cleaned
periodically. Remove it by dragging a thumb over the
screen with enough pressure to pull the screen and
washer out. Rinse it with clean water and then place
it back in the adapter.
Storage
When your pressure washer session has been
completed, turn off the power switch located on the
front of the power washer. Unplug the power cord
from the outlet. Turn off the water supply. Pull the
trigger on the spray gun 2-3 times to drain out the
excess water and to release any remaining water
pressure. Disconnect the garden hose adapter from
the water inlet. DO NOT allow the power washer to
run with no water owing through it.
Remove high pressure hose from spray gun.
Remove lance from the gun. Place the gun in the
holster on the side. Lances are placed into any of
the slots in the back of the unit.
Make sure to discard any remaining detergent
from the bottle. Residual chemical will stick to the
container which could become cotaminated, and
can cause the detergent injector to clog and not
function properly. Flush the bottle and nozzle head
with fresh water to prevent clogging.
Hook the power cord around the cord hook on the
right side of the machine when facing it.
The pressure hose is stored on the hose hook
located on the back of the handle.
DO NOT store the power washer where it is
exposed to freezing temperatures unless you use
an antifreeze designed for pumps. Store the power
washer indoors to prevent the water in the unit from
expanding under freezing conditions. When the
water freezes and expands, your power washer will
be damaged and become inoperable. Or, if storing
outdoors, it is recommended you use pump saver
(not included) to protect pumps.
Cleaning Nozzles
A clogged or partially clogged nozzle can cause
signicant reduction of water pressure coming out
of the nozzle and/or cause the unit to pulsate while
spraying.
Turn off the unit.
Turn off the water supply to the unit.
Relieve any pressure trapped in the hose by
squeezing the trigger 2-3 seconds, and then lock the
spray gun by pushing the lock button.
Remove the lance from the extension lance.
Take off the variable spray nozzle lance. Rotate the
nozzle to open up the metal blades.
Using the nozzle cleaner wire provided (or an
unfolded paper clip), insert the wire into the nozzle
hole and move back and forth until debris is
dislodged.
Tap quick connect end of lance on hard surface
several times.
Back ush water through the nozzles using garden
hose and highest pressure available (either
standard water nozzle or use your thumb over the
nozzle to create water pressure for back ush).
14
PUMP SAVER
1
2
Pump Saver is a product that protects and prolongs
the life of the pump. This will keep the internal parts
of the pump lubricated and protected from freezing
while being stored in ALL climates. It also assists with
protection from internal corrosion. The AR Blue Clean
part #is: PW64511(16oz. bottle). Order online at
www.arblueclean.com
Pump Saver Instructions
Follow the previous storage instructions for your power
washer. To prevent staining, protect the surface under
the power washer from any excess uid. Wear eye
protection when using this product.
Turn unit off and disconnect the gun before adding
pump Saver. Unscrew threaded top from bottle to
remove seal and reattach threaded top to bottle.
Remove black cap from bottle.
1) Place top of pump saver bottle onto the garden hose
adapter.
2) Secure pump saver bottle by turning in a clockwise
direction.
3) Turn the power on.
Note: Instructions on Pump Saver Bottle are generic and
not model specic.
4) Squeeze bottle to help it into the pump.
5) Turn power off when pump saver exits the machine’s
water outlet.
PUMP SAVER
15
PROBLEM CORRECTIVE ACTION
Unit will not turn on. 1. The GFCI module on the end of the power cord must be plugged directly into an outlet.
2. Do not use an extension cord.
3. With the GFCI Connected make sure the power switch is turned on.
Note: When power switch is turned on, the power washer will turn on by itself for 1-2
seconds and shut off. This is normal.
The high pressure
(HP) hose will
not connect/stay
connected to the
spray gun. Is this a
spray gun problem?
1. In most cases, the spray gun is not the problem. The problem is the rubber sleeve
covering the tting at the end of the high pressure hose. It has likely slipped up toward
the metal tip. To x: wiggle, twist and/or pull the rubber sleeve down until the entire tip
is visible plus an 1/8 in. of the metal tting below the tip. Now try to insert the hose tip
into the spray gun. It should “click” into place and will not come out until the hose is
released by pushing in the lever on the underside of the gun. You may cut away the end
of the sleeve with a sharp knife if unable to move the sleeve down. Be careful not to cut
or puncture the hose.
2. Do not push in the release button when connecting the high pressure hose.
The unit is running
but there is no water
ow.
1. Power should NOT be turned on until water comes through the spray gun. Doing so will
damage the motor.
2. Check the water source.
3. Eject the nozzle from the lance to determine if clog is coming from the nozzle (If nozzle
is clogged, see nozzle cleaning instructions under “Cleaning nozzles”).
4. Take off the lance and just spray out of the spray gun. This will indicate if the problem is
with the lance.
5. Check Garden Hose Adapter for loose connection and the lter for debris.
Why is water leaking
where the high
pressure hose
connects to the spray
gun?
1. Make sure there is an o-ring at the end of the metal tip of the high pressure hose. If
no o-ring is present, the connection between the hose and spray gun will leak. O-Ring
Replacement Kit (L) is included with purchase. Additional O-Ring Kits are available
online at www.arblueclean.com or call Customer Service at 1-866-235-5112 to place
an order.
I can’t remove the
lance from the spray
gun. What should I
do?
1. All lances and the detergent bottles are attached and removed from the extension
lance in the same manner. Insert the quick-release end of the lance/detergent bottle
into the extension lance. Press the extension lance and lance together (about a 1/8”)
and turn clockwise. The lance will lock in place. Remove the lance by reversing this
procedure. Press the extension lance and lance together and turn counter clockwise.
The lance will slide out.
2. Or, hold the extension lance and lance in an upright position with the nozzle end on
the oor. Push the whole assembly straight down to loosen the connection, and then
follow the removal process again. You may also spray soapy water or a lubricant in the
area where the lance connects to the extension lance.
If you have any questions regarding the product, please call customer service at 1-866-235-5112.
TROUBLESHOOTING
16
TROUBLESHOOTING
LIMITED WARRANTY
The Warranty of this product is covered by A.R.North America.
This product has a 2 (two) year warranty. Please read the following carefully to understand what each warranty
entails:
This product is under warranty to the original retail consumer against defects in material and workmanship for a
period of 1(one) year and is a complete “bumper to bumper” warranty including the spray gun,the high pressure
hose and all accessories from the date of purchase. The warranty is not transferable or assignable.This warranty
covers replacement parts. This limited one year warranty applies only to products used in consumer applications
and is void in rental or any commercial application. Reasonable care must be used in conformity with operation and
maintenance instructions in the owner’s manual and quick start guide. Failure to follow these instructions will void
this warranty. This warranty gives you special legal rights and you may also have other rights which vary from state to
state.
The second year of the warranty only covers manufacturer defects.
Warranty Process
Keep your original receipt of purchase in case of warranty claim.
If your power washer develops a problem, contact Customer Service:
Call our toll-free number at 1-866-235-5112. Customer Service is available Monday - Friday 8:00 a.m. to 5:00 p.m.
Central Standard Time (CST). A Customer Service Representative will work with you to x the problem.
If the power washer needs to be returned for repair, shipping costs to the company must be paid by the customer. A
Return Merchandise Authorization (RMA) Number will be issued for the return. Upon receiving the power washer,
the company will repair or replace the unit. We will send unit back to customer at no charge.
Please note: Power washers sent to the company without an RMA Number will NOT be accepted and will be
shipped back at the expense of the sender.
PROBLEM CORRECTIVE ACTION
The power washer
turns on for
2 seconds, shuts
off, and will not turn
back on. Do I have a
defective unit?
1. It sounds like your power washer is working just ne. When the water is connected,
the accessories are assembled properly, and the power switch is turned on, the power
washer may turn on for 1 - 2 seconds to prime the pump. It automatically shuts off and
waits for the spray gun trigger to be pressed. When the trigger is pressed, water starts
owing through the pump. The water sensor in the pump “senses” the moving water
and automatically turns the power washer on.
2. Turn the power switch to off, hold in the trigger on the spray gun, so that you have a
steady stream of water. While you are holding the trigger open on the spray gun, at the
same time, turn the power switch on.
17
REPLACEMENT PARTS LIST
Printed in China
For replacement parts, call our customer service department at 1-866-235-5112, 8 a.m. - 5:00 p.m., CST,
Monday - Friday or order online at www.arblueclean.com
PART DESCRIPTION PART #
F GFCI Assembly PW4221160
G Gun Holster PW4222480
H Cord Hook PW4220590
I Garden Hose Adapter PW4221570
J O-Ring Kit PW95824
PART DESCRIPTION PART #
A Foam Cannon (25 oz.) PW4620275
B Super Soft High Pressure
Hose
PW4222400
C Spray Gun PW4381488
D Extension Lance PW4222470
E 15°Quick Connect Nozzle PW4221780
15° – Yellow
A
B
D
E
G
CH
F
JPW95824
I
750ml
600ml
450ml
300ml
150ml
Questions, problèmes, pièces manquantes?
Avant de retourner l'appareil chez le marchand, Ap-
pelez (1-866-235-5112) ou par courriel (info@arnor-
thamerica.com) notre département customerService.
Ils sont disponibles de 8 h à 17 h, HNC, du lundi au
vendredi.www.arblueclean.com
1600 PSI
LAVEUSE À PRESSION ÉLECTRIQUE
GUIDE D'ASSEMBLAGE,
D'ENTRETIEN ET
D'UTILISATION
Modèle BC111HS
LIRE ATTENTIVEMENT
IMPORTANT : CONSERVER CE GUIDE ET
INSÉRER LA FACTURE DANS LE GUIDE POUR
RÉFÉRENCE ULTÉRIEURE.
95497-DK
19
Spécications du produit ................................................................................................. 19
Contenu de l'emballage ...................................................................................................20
Matériel inclus ..................................................................................................................20
Consignes de sécurité .....................................................................................................21
Instructions d'assemblage ..............................................................................................23
Mode d’emploi .................................................................................................................27
Entretien et maintenance ................................................................................................ 29
Protecteur de pompe .......................................................................................................30
Dépannage ....................................................................................................................... 31
Garantie limitée ................................................................................................................32
Liste des pièces de rechange ..........................................................................................33
TABLE DES MATIÈRES
SPÉCIFICATIONS
Modèle PSI maximum
(k/cm2)
(lb/po2)
PSI Évalué
(k/cm2)
(lb/po2)
Débit maximum
(Litre/min)
(Gal./min)
Débit Évalué
(Litre/min)
(Gal./min)
Eau
froide
Volts Fréquence
(Hz)
Ampères Poids
(kg)
(lb)
BC111HS 4 682
(1 600)
3394
(1 160)
6.4
(1.7)
4.5
(1.2)
120 60 12.5 6.6
(14.6)
SPÉCIFICATIONS DU PRODUIT
20
CONTENU DE L'EMBALLAGECONTENU DE L'EMBALLAGE
MATÉRIEL INCLUS
PIÈCE DESCRIPTION QUANTITÉ
H Canon mousse 1
I Lance d’extension 1
J 15°Buses à raccord rapide 1
K Ensemble de joints toriques 1
L Tige de nettoyage de la buse 1
AA Vis 2
PIÈCE DESCRIPTION QUANTITÉ
A Étui à pistolet pulvérisateur 1
B Poignée 1
C Laveuse à pression 1
DCrochet pour cordon
d’alimentation 1
E Tuyau à haute pression 1
F Pistolet pulvérisateur 1
GCran de verrouillage/
déverrouillage 1
OFF/O
ON/I
E
B
C
L
A
DK
AA
PW95824
J
I
F
G
H
750ml
600ml
450ml
300ml
150ml
15° – Yellow
AA
Screws
Qty. 2
Remarque : Les vis se trouvent
dans l’emballage du manuel.
Vis
Qté 2
15°– Jaune
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

AR Blue Clean BC111HS Le manuel du propriétaire

Catégorie
Nettoyeurs haute pression
Taper
Le manuel du propriétaire