BE Power Equipment P2713EN Manuel utilisateur

96673-DG

04.2023

2,700 PSI

OPERATOR'S MANUAL

ELECTRIC PRESSURE WASHER

MANUEL D’UTILISATION DU LAVEUSES PRESSION

MANUAL DEL OPERADOR DE LA LAVADORA A PRESIÓN

P2713EN

2

Congratulations on your purchase of a BE Power Equipment pressure washer. You can be confident

that this pressure washer is constructed and tested with optimum performance and quality in mind.

Reading this manual will help get you the best results for set-up, operation, maintenance and avoid

personal injury or damage to your machine. By knowing how best to operate this machine, you will be

better positioned to show others who may also operate the unit.

All the information in this manual is based on the latest product information available at the time

of printing. BE Power Equipment reserves the right to make changes at any time without notice or

incurring any obligation.

Owner/Operator Responsibility

The owner/operator must have a thorough understanding of the operation, maintenance and dangers

associated with using this machine. It must be understood that it is ultimately up to the owner/operator

to safely use this machine as outlined in this manual.

This manual is considered a part of the machine and needs to be kept in a safe location. If the

machine is resold or given to someone else, this manual needs to be included.

Record Identification Numbers

It is recommended that you record the product identification numbers in this manual. These numbers

are important to have on hand if you need to contact technical support (1-866-850-6662). The model

and serial number can be found on the box and on decal on the machine.

Product Registration

Please register your product online to get the maximum benefit from your warranty. Use the QR code

below or register online at: bepowerequipment.com/product-registration

It is recommended that you record the product identification numbers in this manual. These numbers

are important to have on hand if you need to contact technical support (1-866-850-6662). The model

and serial number can be found on the box and on decal on the machine.

PRODUCT IDENTIFICATION

Model Number: P2713EN

Date of Purchase:

Dealer Name:

3

TABLE OF CONTENTS

SPECIFICATIONS

Model Max PSI

(lbs/sq. in.)

Rated PSI

(lbs/sq. in.)

Max GPM

(Gal/per min)

Rated GPM

(Gal/per min)

Cold

Water

Volts Frequency

(Hz)

Amps Weight

(lbs.)

P2713EN 2700 2150 1.3 1.1 120 60 15 40.8

PRODUCT SPECIFICATIONS

Product Specications ...................................................................................................... 3

Package Contents ............................................................................................................. 4

Hardware Contents ........................................................................................................... 4

Safety Information ............................................................................................................. 5

Assembly Instructions ....................................................................................................... 7

Operating Instructions .....................................................................................................12

Care and Maintenance ................................................................................................... 14

Pump Saver ..................................................................................................................... 15

Troubleshooting ............................................................................................................... 16

Limited Warranty ............................................................................................................. 17

Replacement Parts List .................................................................................................. 18

4

PACKAGE CONTENTSPACKAGE CONTENTS

HARDWARE CONTENTS

PART DESCRIPTION QUANTITY

KSpray Gun 1

LSpray Gun Trigger Lock 1

M Spray Gun Holster 1

NHigh Pressure Hose 1

OHigh Pressure Foam Cannon 1

AA Shims 4

BB Cotter Pins 2

CC Screws 2

DD Screws 2

PART DESCRIPTION QUANTITY

AHose Hook 1

BHandle 1

C Rotary Nozzle 1

DO-Ring Replacement Kit 1

EQuick Connect Nozzles 4

F Power Washer Unit 1

G Rotary Nozzle Holder 1

HNozzle Cleaning Wire 1

I Extension Lance 1

JWheels 2

F

M

A

N

K

J

C

I

L

G

H

AA CC

BB

D

PW95824

O

DD

B

E

25° – Green

40° – White

0° – Red

15° – Yellow

AA CC

BB

Shims

Qty. 4

Screws

Qty. 2

Cotter Pins

Qty. 2 DD Screws

Qty. 2

5

SAFETY INFORMATIONSAFETY INFORMATION

Please read and understand this entire manual before

attempting to assemble and operate the product.

This manual contains information that relates to

PROTECTING PERSONAL SAFETY and PREVENTING

EQUIPMENT PROBLEMS. It is very important to read this

manual carefully and understand it thoroughly before

using the product. The symbols listed below are used to

indicate this information.

DANGER

Potential hazard that will result in serious injury or

loss of life.

WARNING

Hazard that could result in serious injury or loss of

life.

CAUTION

Potential hazard that may result in moderate injury

or damage to equipment.

Note: The word “Note” is used to inform the reader of

something the operator needs to know about the tool.

WARNING

To reduce the risk of injury, the user must read

and understand the instructions before using

this product.

1. Warning – When using this product, basic

precautions should always be followed, including the

following.

2. Read all the instructions before using the product.

3. Know how to stop the product and bleed pressures

quickly. Be thoroughly familiar with the controls.

4. Keep operating area clear of persons.

5. Do not overreach or stand on unstable support. Keep

good footing and balance at all times.

6. Follow the maintenance instructions as specied in

the manual.

7. To avoid personal injury and/or damage to property

and to maximize your power washer experience,

carefully follow all of the safety tips, instructions,

warnings and safeguards and become familiar with

all of the controls. Be sure you know how to quickly

bleed off the pressure from all parts of your power

washer and how to turn off the power washer.

8. This power washer conforms to CSA and other safety

and consumer standards. DO NOT modify or rebuild

any part of your power washer.

9. DO NOT use your power washer when you are under

the inuence of alcohol or drugs. Use this power tool

carefully and only when you are alert.

10. Watch your balance and footing while using your

power washer. Surfaces become slippery when wet

and are extra slippery when using a detergent or

cleaner.

11. NEVER operate the power washer in bare feet,

sandals, or open-toed shoes.

12. When using the power washer near children, make

sure they are closely supervised by an adult to avoid

injury. NEVER let a child use the power washer.

13. Keep ngers, hands, feet and any part of your body

clear of the stream of high pressure water. The

powerful spray can cause blindness or blast holes in

the skin. It can break a window if you are too close

when you pull the trigger on the spray gun.

14. ALWAYS wear eye protection to prevent injury to

eyes when operating the power washer.

15. To avoid mishaps or injury, ALWAYS use the trigger

safety lock when not using the power washer even if

only stopping briey.

16. The power washer is equipped with a Ground Fault

Circuit Interrupter (GFCI) (For US unit only) which

greatly reduces the chance of electric shock while

the unit is in use. If replacement of the plug or cord

is needed, use only identical replacement parts.

17. Point the spray gun in a safe direction when

beginning a power washer session.

18. Warning- NEVER spray directly at a person, animal,

electrical device or the unit itself.

19. When rst using the spray gun, hold the spray gun

and lance with two hands when pulling the trigger

(one hand to pull the trigger and the other to

stabilize the gun assembly) until you get used to the

“kickback” from the spray gun.

20. When you turn the power switch off, water pressure

may remain in the system. To discharge the

pressure, point the spray gun in a safe direction

and pull the trigger.

21. NEVER spray ammable liquids.

22. NEVER use the power washer in areas that contain

combustible dust, liquids or vapors.

23. Avoid contact of the pressure hose with sharp

objects and examine the hose regularly. Replace

if damaged. Due to the high pressure involved, it

cannot be repaired if cut or damaged.

24. Only use detergent specically formulated for power

washers and follow instructions on the detergent’s

label. Dish or laundry soap is too thick and will

clog the nozzle of your foam cannon.

25. Protect eyes, lungs, and skin from exposure to

detergent.

26. Warning-If connection is made to a potable water

6

SAFETY INFORMATIONSAFETY INFORMATION

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

system, the system Should be protected against

backow.

CAUTION

Store the power washer indoors to prevent the

water in the unit from expanding under freezing

conditions. When the water freezes and

expands,

your power washer will be damaged and become

inoperable. Or, if storing outdoors, it is

recommended you use pump saver (not included)

to protect pumps.

27. NEVER use hot water with your power washer. It will

overheat and damage the high pressure pump.

28. NEVER leave the power washer unattended while it

is powered “ON”.

29. ALWAYS turn the water supply on before turning the

power washer power to on. Running the pump dry

will cause damage to the internal components.

30. NEVER use a water supply to your power washer

that exceeds 150 PSI maximum.

31. NEVER disconnect the high pressure hose from the

power washer while the system is pressurized.

32. NEVER permanently engage the trigger mechanism

on the spray gun.

33. NEVER operate the power washer unless all

components are properly and securely connected.

34. NEVER allow the power washer pump to run for

more than one minute after you have turned off the

water supply. This can cause the motor and pump to

overheat and fail.

35. NEVER use lances or other parts that are not

compatible for this specic AR BLUE MAXX unit.

36. NEVER use an extension power cord since it defeats

the effectiveness of the GFCI (For US unit only) and

increases the chance of electrocuting the operator.

37. NEVER spray any electrical outlet with your power

washer.

38. Inspect the power cord before using. DO NOT use it

if it is damaged.

39. Stay alert - watch what you are doing.

Ground Fault Circuit Interrupter Protection (For US unit

only)：

This pressure washer is equipped with a ground-fault

circuit-interrupter (GFCI) built into the plugs of the

power-supply cord. This device provides additional

protection from the risk of electric shock and have

automatic detection function to detect whether

the additional protection function is invalid. Should

replacement of the plug or cord become necessary,

use only identical replacement parts that include GFCI

protection.

This product must be grounded. If it should malfunction

or breakdown, grounding provides a path of least

resistance for electric current to reduce the risk of

electric shock. This product is equipped with a cord

having an equipment-grounding conductor and a

grounding plug. The plug must be plugged into an

appropriate outlet that is properly installed and

grounded in accordance with all local codes and

ordinances.

DANGER – Improper connection of the equipment-

grounding conductor can result in a risk of electrocution.

Check with a qualied electrician or service personnel

if you are in doubt as to whether the outlet is properly

grounded. Do not modify the plug provided with the

product – if it will not t the outlet, have a proper outlet

installed by a qualied electrician. Do not use any type

of adaptor with this product.

7

PREPARATION

Before beginning assembly of product, make sure all

parts are present. Compare parts with package contents

list and hardware contents list. If any part is missing or

damaged, DO NOT attempt to assemble the product.

Please call customer service at 1-866-850-6662.

Replacement parts will be sent no charge.

Estimated Assembly Time: 5 minutes.

Tools Required for Assembly (not included): Phillips

screwdriver.

ASSEMBLY INSTRUCTIONS

PREPARATION

1

AA

J

2

3

1

BB

F

2

B

F

3

2

1

Shims

Cotter Pins

x 4

x 2

AA

BB

AA CC

BB

Shims

Qty. 4

Screws

Qty. 2

Cotter Pins

Qty. 2 DD Screws

Qty. 2

AA CC

BB

Shims

Qty. 4

Screws

Qty. 2

Cotter Pins

Qty. 2 DD Screws

Qty. 2

Hardware Used:

Wheels Assembly

Install shims (AA) and wheels (J) to power washer unit

(F). Secure with cotter pins (BB).

Press buttons on power washer unit (F) and install

handle (B). power washer unit (F) will click when handle

is in proper position.

8

3

G

A

FDD

4

F

A

DD

M

5

CC

F

CC

A

ASSEMBLY INSTRUCTIONS

Install rotary nozzle holder (G) and one side of hose

hook (A) to power washer unit (F). Secure with screw

(DD).

Screw x 1

DD

Hardware Used:

AA CC

BB

Shims

Qty. 4

Screws

Qty. 2

Cotter Pins

Qty. 2 DD Screws

Qty. 2

Install spray gun holster (M) and another side of hose

hook (A) to power washer unit (F). Secure with screw

(DD).

Fix the bottom of hose hook (A) on the power washer

unit (F). Secure with screws (CC).

Screw

Screws

x 1

x 2

DD

CC

Hardware Used:

AA CC

BB

Shims

Qty. 4

Screws

Qty. 2

Cotter Pins

Qty. 2 DD Screws

Qty. 2

AA CC

BB

Shims

Qty. 4

Screws

Qty. 2

Cotter Pins

Qty. 2 DD Screws

Qty. 2

9

ASSEMBLY INSTRUCTIONS

Locking Spray Gun (before Lance installation) To lock

trigger of spray gun (K), point gun away from you and

turn dial to lock (“3” and “9” position). Squeeze or pull

trigger to make sure it is locked. Always leave in locked

position when not in use. This ensures the gun is in

“safe” mode until it is ready for use. Turn dial to unlock

(“12” and “6” position) to release spray gun trigger.

Note: The trigger lock prevents trigger from being

accidentally engaged.

Attach one end of high pressure hose (N) into the

connector of spray gun (K) by pressing the end into

place. It will make a “click” sound when rmly in place.

The hose is now securely attached to spray gun.

To remove the high pressure hose (N), pull back on

collar of spray gun (K) and pull out the hose.

Extension Lance Installation

While spray gun (K) is in the locked position, insert

lance (I) into the end of spray gun by inserting and turn-

ing clockwise until fully in place. To remove, turn coun-

terclockwise.

K

N

67

K

N

2

N

1

8

K

1

Unlocked Locked

I

K

1

2

9

10

ASSEMBLY INSTRUCTIONS

10

I

E

C

1

2

1

11

I

E

C

To remove nozzle (E) and Rotary nozzle (C), pull back on

collar of lance (I) and pull out nozzle.

Pull back on collar of lance (I), attach nozzle (E) or ro-

tary nozzle (C) into end of lance (I) by pressing selected

nozzle into place. It will make a “click” sound when

rmly in place.

Note: Always push safety lock button to lock trigger

when changing lances and nozzles to ensure that they

do not accidentally eject with force during removal.

Foam Cannon Installation

The foam cannon (O) comes with a straw which is tted

into high pressure top. If you do not see the straw,

look inside the foam cannon and attach it to the high

pressure top. When using foam cannon, ll it with a

properly formulated detergent or cleaner with a water

ratio according to instructions on the container.

DO NOT use thick or gel-like detergents as they will clog

the foam cannon and can cause damage.

12

1

750ml

600ml

450ml

300ml

150ml

2

O

Pull back on collar of lance (I), attach foam cannon (O)

into end of lance by pressing cannon into place. It will

make a “click” sound when rmly in place.

Note: Always lock spray gun when changing the foam

cannon to ensure it does not eject with force.

When using the foam cannon, ll it with a properly

formulated detergent or cleaner with water ratio

according to instructions on the container.

I

O

13

2

1

11

Attach the another end of high pressure hose (N)

into the pump outlet connector by pressing the end

into place. It will make a “click” sound when rmly

in place. Conrm hose is locked into power washer

unit by slightly pulling on hose. The hose is now

securely attached.

Foam Cannon Storage

Store the foam cannon (O) on the back of the hose

hook (A).

14

O

A

ASSEMBLY INSTRUCTIONS

16

F

Attach a garden hose to built in garden hose

adapter. The water is now connected to your power

washer.

Note: Flush out garden hose before connecting to

garden hose adapter

You have now completed the assembly and are ready

to begin using your electric power washer. Read and

observe all safety instructions.

15

N

12

OPERATING INSTRUCTIONSOPERATING INSTRUCTIONS

• Make sure the power switch is off (light will be off).

• Unwind the power cord completely and plug

into a grounded 120 volt outlet.

• Turn on water supply at the faucet to completely open.

• Turn the safety lock button on the spray gun to

unlocked. While pointing the spray gun in a safe

direction, squeeze the trigger on the spray gun until

there is a steady stream of water, letting the water

and air out of the hose.

• Turn the power switch to the “ON” (|) position. The

unit will turn on for 1 - 2 seconds and shut off. This is

a normal function of the auto start feature. Squeeze

the spray gun trigger to begin pressure washing.

• Squeeze the spray gun trigger to begin pressure

washing.

• Begin power washing by squeezing the trigger on the

K

lock

• Always test a small area to avoid chance of damaging

the surface.

spray gun all the way into the handle.

• Release the spray gun trigger to stop the power

washer.

• Allow the motor to come to a complete stop before

squeezing the trigger again.

• Squeezing rapidly will cause the auto start feature to

miss an on/off cycle that may prevent it from turning

on while squeezing trigger after rapid squeezing. Use

slow, deliberate trigger pulls to avoid this.

O

I

Adjusting Soap Levels on Foam Cannon

Twist knob to adjust the level of soap as indicated on

the top of the Foam Cannon (O). Twist toward the

higher concentration of bubbles for more soap, or the

opposite direction for less.

OFF/0

ON/I

OFF/0

ON/I

13

OPERATING INSTRUCTIONS

• The power washer will pull a ratio of water to

detergent of 10:1 or 10 parts water to 1 part

detergent. The detergent concentration can be

adjusted by turning the detergent knob on the top of

the machine. Turn it left for more concentration or

turn it right for less concentration.

Operation Tips

• Note:

Test the GFCI (For US unit only) before each use:

1. Plug GFCI into power outlet. Indicator should turn

green to show that cord has power.

2. Press test button, green indicator should turn off

to verify that GFCI cut off power to the cord.

3. Press reset button – green indicator should turn

on to show that cord has power again.

4. When GFCI is working properly, green indicator will

turn on when power is applied. If green indicator

turns off, it has detected electric leakage and the

GFCI cut off power to the appliance.

• If you hear the motor run intermittently when the

trigger is not being squeezed, that is normal.

The pump is priming itself so it is ready to operate

when the trigger is squeezed. Turn off the power

washer if not being used after ve minutes.

• The o-rings on the bayonet end of the nozzle should

be cleaned regularly and lubricated with non-water

soluble grease such as petroleum jelly (not included).

• Keep the nozzle cleaning wire for use in unclogging

the nozzle. If you lose the cleaning wire, a

straightened paper clip also works.

How to Avoid Damaging Surfaces

• Damage to surfaces being cleaned occurs because

the impact force of the water pressure exceeds

the durability of the surface. Bare wood can be

penetrated, paint can be peeled off, etc. You can vary

the force of your power washer by controlling:

1. The angle of the surface being cleaned.

2. The distance of the nozzle from the surface being

cleaned.

• Never use a narrow high pressure stream of water on

soft surfaces susceptible to damage.

• Use the 25˚ quick connect nozzle when cleaning

windows. Squeeze the trigger and vary the spray

pattern and angle until optimum cleaning efciency is

achieved.

Using Power Cord

• Remove the power cord from the unit by swiveling the

cord hook to the up or down. The power cord then can

be slid off to the side of the power washer unit.

• Swivel cord hook back to left or right when ready to

wrap the cord back into place for storage.

14

CARE AND MAINTENANCE

Detergents

• Use detergents designed for power washers.

Hardware stores or home centers also have power

washer detergents for different cleaning projects. The

cleaning solution should be the consistency of water

in order to prevent clogging your detergent bottle and

nozzle.

• This system applies detergent under low pressure.

The cleaning power of the detergents is enhanced

when applied with low pressure and enough

time is given to break down dirt and grime. The

combination of low pressure and chemical action

is very effective and can be better than scrubbing

if applied properly. Always spray detergent on a dry

surface. Do not pre-soak area. Wetting the surface

rst dilutes the detergent and reduces its cleaning

ability. Do not allow detergent to dry on surface. On

vertical surfaces being cleaned, apply detergent

to lower surfaces and work your way up to prevent

detergent from causing streaks in the dirt and

grime. Rinse detergent by pressure washing from

bottom up for same reason.

• If a stain is particularly tough, it may be necessary

to reapply the detergent and use a bristled brush to

scrub the stain. Subsequent power washing after

brushing should successfully complete your cleaning

job.

Cleaning Garden Hose Adapter

• The screen inside the adapter should be cleaned

periodically. Remove it by dragging a thumb over the

screen with enough pressure to pull the screen and

washer out. Rinse it with clean water and then place it

back in the adapter.

Cleaning Nozzles

• A clogged or partially clogged nozzle can cause

signicant reduction of water pressure coming out

of the nozzle and/or cause the unit to pulsate while

spraying.

• Turn off the unit.

CARE AND MAINTENANCE

Storage

• When your pressure washer session has been

completed, turn off the power switch. Unplug the

power cord from the outlet. Turn off the water supply.

Pull the trigger on the spray gun 2-3 seconds to drain

out the excess water and to release any remaining

water pressure. Do not allow the power washer to run

with no water owing through it.

• Remove high pressure hose from spray gun and

unscrew the other end of the high pressure hose from

the power washer.

• Turn off the water supply to the unit.

• Relieve any pressure trapped in the hose by

squeezing the trigger 2 - 3 times, then lock the spray

gun by turning the dial to lock (“3” and “9” position).

• Using the nozzle tip cleaner provided (or an unfolded

paper clip), insert the wire into the nozzle hole and

move back and forth until debris is dislodged.

• Back ush water through the nozzles using garden

hose and highest pressure available (either standard

water nozzle or use your thumb over the nozzle to

create water pressure for back ush).

15

CARE AND MAINTENANCE

Pump Saver is a product that protects and prolongs

the life of the pump. This will keep the internal parts

of the pump lubricated and protected from freezing

while being stored in ALL climates. It also assists with

protection from internal corrosion.

Pump Saver Instructions

Follow the previous storage instructions.

To prevent staining, protect the surface under the

power washer from any excess uid. wear ear and eye

protection when using this product.

Turn unit off and disconnect the gun before adding

pump saver. Unscrew threaded top from bottle to

remove seal and reattach threaded top to bottle.

Remove black cap from bottle.

1) Place top of pump saver bottle onto the garden

hose adapter.

2) Secure pump saver bottle by turning in a clockwise

direction.

3) Turn the power on.

4) Squeeze bottle to help it into the pump.

5) Turn power off when pump saver exits the machine’s

water outlet.

Note: Instructions on Pump Saver Bottle are generic and

not model specic.

2

1

• The high pressure hose is stored on the hose hook

located on the back of the handle.

• Insert extension lance into nozzle tray, and press spray

gun with extension lance into spray gun holster.

• Make sure to discard any remaining detergent from

the foam cannon. Residual chemical will stick to the

container which could become contaminated and

can cause the foam cannon injector to clog and not

function properly. Flush the foam cannon and nozzles

with clear water to prevent clogging.

• The quick connect nozzles are stored on the nozzle

holder located on the spray gun.

• Put the rotary nozzle on the rotary nozzle holder, which

on the right of the power washer.

• Store the foam cannon on the back of the power

washer.

• Wind the power cord around the cord hooks located

on the back of the power washer.

• DO NOT store the power washer where it is

exposed to freezing temperatures unless you use

an antifreeze designed for pumps. Store the power

washer indoors to prevent the water in the unit from

expanding under freezing conditions. When the

water freezes and expands, your power washer will

be damaged and become inoperable. Or, if storing

outdoors, it is recommended you use pump saver (not

included) to protect pumps.

PUMP SAVER

16

PROBLEM CORRECTIVE ACTION

Unit will not turn on. 1. Make sure the power washer is OFF. Plug in the electrical cord to a grounded 120 volt

outlet (no electrical extension cord should be used). If the electrical cord will not plug

into your outlet, your electrical outlet is not properly grounded and should not be used.

Use another electrical outlet.

2. If this did not correct the problem, try plugging into another electrical outlet and repeat

the above procedure. If it is still not working, call Customer Service. 1-866-850-6662

The high pressure

(HP) hose will

not connect/stay

connected to the

spray gun. Is this a

spray gun problem?

1. In most cases, the spray gun is not the problem. The problem is the rubber sleeve

covering the tting at the end of the high pressure hose. It has likely slipped up toward

the metal tip. To x: wiggle, twist and/or pull the rubber sleeve down until the entire tip

is visible plus an 1/8 in. of the metal tting below the tip. Now try to insert the hose tip

into the spray gun. It should “click” into place and will not come out until the hose is

released by pushing in the lever on the underside of the gun. You may cut away the end

of the sleeve with a sharp knife if unable to move the sleeve down. Be careful not to cut

or puncture the hose.

The unit is running

but there is no water

ow.

1. Power should NOT be turned on until water comes through the spray gun. Doing so will

damage the motor.

2. Check the water source.

3. Eject the nozzle from the lance to determine if clog is coming from the nozzle (If nozzle

is clogged, see nozzle cleaning instructions under “Cleaning nozzles”).

4. Take off the lance and just spray out of the spray gun. This will indicate if the problem is

with the lance.

5. Check Garden Hose Adapter for loose connection and the lter for debris.

Why is water leaking

where the high

pressure hose

connects to the spray

gun?

1. Make sure there is an o-ring at the end of the metal tip of the high pressure hose. If

no o-ring is present, the connection between the hose and spray gun will leak. O-Ring

Replacement Kit (D) is included with purchase.

I can’t remove the

lance from the spray

gun. What should I

do?

1. All lances are attached and removed from the spray gun in the same manner. Insert

the end of the lance into the spray gun. Press the spray gun and lance together (about

a 1/8 in.) and turn the collar of the gun clockwise. The lance will lock in place. Remove

the lance by reversing this procedure. Press the spray gun and lance together and turn

counter clockwise. The lance will slide out.

2. Hold the spray gun and lance in an upright position with the nozzle end on the oor.

Push the whole assembly straight down to loosen the connection, and then follow the

removal process again. You may also spray soapy water or a lubricant in the area where

the lance connects to the spray gun.

The power washer

turns on for

2 seconds, shuts

off, and will not turn

back on. Do I have a

defective unit?

1. When the water is connected, the accessories are assembled properly, and the power

is turned on, the power washer may turn on for 1 - 2 seconds to prime the pump. It

automatically shuts off and waits for the spray gun trigger to be pressed. When the

trigger is pressed, water starts owing through the pump. The water sensor in the pump

“senses” the moving water and automatically turns the power washer on.

2. Turn the power off, hold in the trigger on the spray gun so that you have a steady stream

of water. While you are holding the trigger open on the spray gun, at the same time, turn

the power on.

TROUBLESHOOTING

If you have any questions regarding the product, please call customer service at 1-866-850-6662.

17

TROUBLESHOOTINGLIMITED WARRANTY

BE Power Equipment Inc. warrants the original retail purchaser that this pressure washer is free from defects

in material and workmanship for one year. If defects are found in BE Power Equipment products within the

limitations outlined in this warranty statement, BE Power Equipment, at its sole discretion, will repair or replace

the product free of charge.

The warranty coverage is for one year and begins on the date of purchase by the end-user. Valid proof of

purchase must be presented with the warranty claim.

This warranty is limited to defects that occurred during regular operational use. This warranty does not cover

failures due to lack of service, negligence, abuse or misuse. Including, but not limited to, freezing damage,

alterations, chemical deterioration, scale build-up, rust, corrosion, thermal shock, thermal expansion,

transportation damage, oil changes, valve adjustments, fuel system maintenance or using incorrect repair

parts. Furthermore, Using the wrong fuel, water or power supply is considered a form of misuse.

This warranty also does not cover normal wearing items such as O-rings, valves, seals, lters, sparkplugs or

packings. These are considered to be maintenance items.

To obtain warranty, the claimant must take the product, with their original proof of purchase, to an authorized

BE Power Equipment service center. These service centers are located on the website:

https://www.bepowerequipment.com/service-centers

If you cannot resolve the warranty claim satisfactorily, contact the BE Power Equipment Warranty Department

(1-866-850-6662). Be prepared with details of the defect, proof of purchase,and model.

18

DO NOT RETURN THIS PRODUCT TO THE RETAILER

CONTACT OUR CUSTOMER SERVICE if you need assistance

with the assembly, operation, or if you experience a problem with

your pressure washer, please call 1-866-850-6662

Monday - Friday. 8AM to 430PM PST.

NE RENVOYEZ PAS CE PRODUIT AU DÉTAILLANT, CONTACTEZ

NOTRE SERVICE À LA CLIENTÈLE si vous avez besoin d’aide

pour l’assemblage, le fonctionnement ou si vous rencontrez un

problème avec votre nettoyeur haute pression, veuillez appeler le

1-866-850-6662 Lundi à Vendredi. De 8h à 430h PST.

NO DEVUELVA ESTE PRODUCTO AL MINORISTA

COMUNÍQUESE CON NUESTRO SERVICIO DE ATENCIÓN AL

CLIENTE si necesita ayuda con el ensamblaje, el funcionamiento

o si tiene algún problema con su hidrolimpiadora, llame al

1-866-850-6662 Lunes a Viernes, de 8AM a 430PM PST.

ELECTRIC PRESSURE WASHER

OPERATOR'S MANUAL

MANUEL D’UTILISATION DU LAVEUSES PRESSION

MANUAL DEL OPERADOR DE LA LAVADORA A PRESIÓN

04.2023

2,700 PSI

MANUEL D’OPÉRATEUR

LAVEUSE À PRESSION ÉLECTRIQUE

ELECTRIC PRESSURE WASHER OPERATOR’S MANUAL

MANUAL DEL OPERADOR DE LA LAVADORA A PRESIÓN

P2713EN 96673-DG

20

TABLE DES MATIÈRES

CARACTÉRISTIQUES

Modéle PSI MAX

(k/cm2)

(lb/po2)

PSI Évalué

(k/cm2)

(lb/po2)

Débit MAX

(Litre/min)

(Gal./min)

Débit Évalué

(Litre/min)

(Gal./min)

Eau froide

uniquement

Volts Fréquence

(Hz)

Ampères Poids

(kg)

(lb)

P2713EN 7901

(2700)

6292

(2150)

4.9

(1.3)

4.2

(1.1) 120 60 15 18.5

(40.8)

CARACTÉRISTIQUES DU PRODUIT

Caractéristiques du produit ................................................................................ 20

Contenu de l’emballage ...................................................................................... 21

Quincaillerie incluse ............................................................................................ 21

Consignes de sécurité ........................................................................................ 22

Instructions pour l’assemblage .......................................................................... 24

Mode d’emploi .....................................................................................................29

Entretien .............................................................................................................. 31

Protecteur de pompe .......................................................................................... 32

Dépannage .......................................................................................................... 33

Garantie limitée ................................................................................................... 34

Liste des pièces de rechange ............................................................................. 35

La page charge ...

BE Power Equipment P2713EN Manuel utilisateur

BE Power Equipment P2713EN Manuel utilisateur

dans d''autres langues

Autres documents