Midland BTR1 Advanced Mode d'emploi

BTR1 Advanced
Midland
Marque
Midland
Modèle
BTR1 Advanced
Taper
Mode d'emploi
PAIRING 4 UNITS IN CONFERENCE
Status: Settings
Note: the Conference mode allows the simultaneous communication
amongst units. All units must be paired in a “chain” configuration: the
Down button of the first unit must be paired to the Up button of the second
unit and so on. For a detailed description of the function go to paragraph
“Conference” of the complete user manual or watch the video tutorial
MIDLAND INTERCOM PAIRING
Status: Settings
3” 3”
Press for 3 seconds Press for 3 seconds
Flashes Flashes
Confirm (1 sec.) Confirm (1 sec.)
Pairing successful
ON/OFF
DESCRIPTION OF BUTTONS
Vol + Vol -
Led
Led
Control
Button
Up
Button
Down
Button
SWITCH ON
3”
Press for 3 seconds
Beep
Flashes
SWITCH OFF
3”
Press together for 3 sec.
Flashes
Notification jingle
DESCRIPTION OF BUTTONS
Main pairing:
Phone, TFT, GPS
(Mono/Stereo)
Secondary pairing with:
GPS, 2nd phone
(Mono)
Pairing with:
Midland Intercom
Other brand intercom
Pairing with:
Midland Intercom
PAIRINGS
ACCESS SETTINGS
Status: device o
7”
Press for 7 seconds
Beep
Flashes
Static
PHONE, GPS, TFT PAIRING
Status: Settings
3”
Press for 3 seconds
Beep
Flashes
Select BTR1 Advanced
on phone, GPS or TFT
Beep
Confirm (1 sec.)
POCKET GUIDE
Note: to pair a 2nd device in mono audio, repeat this procedure using Vol -.
Note: to pair another Midland intercom, follow the same procedure using the
Up/Down buttons.
OTHER BRAND INTERCOM PAIRING
UNIVERSAL INTERCOM
Status: Settings
7”
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
1
2
3
1
2
3
1
2
3
Press for 7 seconds
Follow procedure to pair with a
phone
Flashes fast
(press and hold)
Flashes slowly
(Release)
RESET BLUETOOTH PAIRINGS
Status: Settings
3”
Press together, 3 seconds
Beep
Confirm (1 sec.)
Static
EXIT SETTINGS MODE
CANCEL PAIRING
Status: Settings
x2
Press 2 times
Flashing changes
ATTENTION: To carry out any pairings you need to access Settings.
If the Control button is pressed for fewer than 7 seconds, the device will
switch itself on instead of accessing Settings. If this occurs, repeat the
process.
Go to our website midlandeurope.com,
download the complete manual and the
BT Updater software.
Customize your intercom and discover all the
functions with the BTPRO SetApp.
Download it here: HIGH DEFINITION SOUND BY
Frequency (GHz) Max power (mW)
2.402 - 2.480 100
Pairing with:
Midland intercom (Vox,
music sharing)
3”
3”
3”
BTR1 ADVANCED
Bike to Bike Conference Communication
CONFERENCE
CONFERENCE
ENGLISH
1
Produced or imported by:
Midland Europe srl
Via R. Sevardi 7 - 42124 Reggio Emilia - Italy.
OPERATING MODES
A. Intercom Mode: to communicate with another device.
B. Phone Mode: for phone calls or for managing music.
C. FM Radio Mode: to listen to radio, search and store stations.
Note: Phone mode and Intercom mode are enabled only when your intercom
is paired to other devices.
CHOOSE OPERATING MODE
Status: device on
3”
INTERCOM MODE
PHONE MODE FM RADIO MODE
Press for 3 seconds to change mode or press and hold to scroll
quickly
Operating mode status
Note: By pressing simultaneously Vol + and Vol -, BTR1 Advanced
communicates the selected operating mode.
INTERCOM MODE
FUNCTION DESCRIPTION
Rider 2
(Passenger) Rider 1
Rider 3
TO OPEN/CLOSE INTERCOM MANUALLY
Status: Intercom mode
x1
Press 1 time
Beep
Flashes
TO OPEN/CLOSE INTERCOM BY VOICE
Status: in all modes
Say “Hi”
Voice announcement
Flashes
Silent for 40 sec. the intercom deactivates
Beep
VOX ACTIVATION/DEACTIVATION
Status: in all modes
7”
Press for 7 seconds
Voice announcement
TO OPEN/CLOSE UNIVERSAL INTERCOM
Status: Intercom mode
3”
Press for 3 seconds to activate or
deactivate the Universal Intercom
Beep
Flashes
Note: Voice activation is only possible when the intercom device is paired
with the Control button.
Note: to activate/deactivate the audio from a dierent brand device, use the
voice call command (for some models it is necessary to send the voice call
twice)
MAKING A CALL
Status: Phone mode
x1
Press 1 time
Voice Assistant Response
(Google assistant, Siri)
Give instructions
Call
PHONE MODE
FUNCTION DESCRIPTION
Play/Pause
(Phone on Vol+)
• Call
• Answer
• End
• Reject
• Next song
Seek previous station
Previous memory
radio station
ANSWERING/ENDING A CALL  REJECTING A CALL
Status: All modes
x1
Press 1 time to answer/end a call
3”
Press for 3 sec. to reject a call
Note: If you have a phone paired with the Vol - button, use the Down button.
RADIO MODE
FUNCTION DESCRIPTION
MUSIC
Status: Phone mode
Select Music app
x1
Press 1 time Play/Pause
x1
Press 1 time Next track
x1
Press 1 time Previous track
3”
Press for 3 sec. Start/stop sharing
music with passenger (paired with
Control button)
FM Radio
On/O
Seek next station
Next memory radio
station
(Phone on Vol-)
• Call
• Answer
• End
• Reject
• Previous track
FM RADIO
Status: Radio mode
x1
Press 1 time ON/OFF
x1
Press 1 time Next station
3”
Press for 3 seconds Next preset
x1
Press 1 time Previous station
3”
Press for 3 seconds
Previous preset
SHORTCUT: In Intercom/FM radio modes pressing Control
2 times activates/deactivates the music. SHORTCUT: In Phone mode by pressing the UP/DOWN
buttons twice, turns the Intercom on/o (Rider 1, 3).
Note: If you have a phone paired with the Vol - button, use the Down button.
Nota: to communicate with Rider 1/3 repeat the process pressing the Up/
(Rider 1)/Down (Rider 3) buttons.
Rider 4
(Universal Intercom)
TO OPEN/CLOSE CONFERENCE
Status: Conference mode
x1
Press once
opens/closes Conference
to the unit paired to button
Up.
x1
Press once
opens Conference to all
units paired.
x1
Press once
opens/closes Conference
to unit paired to button
Down.
TO ENABLE/DISABLE THE CONFERENCE MODE
Status: in all modes
3”
Keep pressed together for
3 seconds; the Conferen-
ce mode will be enabled/
disabled.
Voice announcement
Connection status
Note: in Conference mode, the devices paired to Vol+/Vol- are temporarily
disconnected.
FCC Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly approved by the part responsible
for compliance could void the user’s authority to operate the equipment.
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to
two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme
aux CNR d’Innovation, Sciences et Développement économique Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) L’ appareil ne doit pas produire de brouillage. (2) L’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’ en compromettre le
fonctionnement.
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio
frequency exposure limits, The Wireless Device should be used in such a manner such that
the potential for human contact during normal operation is minimized. This device has been
evaluated for and shown compliant with the IC Specific Absorption Rate (“SAR”) limits when
operated in portable exposure conditions.
Limited Warranty
Midland Radio Corporation oers a limited warranty on this product. You may obtain and review
the terms of the limited warranty at https://midlandusa.com/pages/warranty. You may also mail
a request for a written copy of the limited warranty terms to Midland Radio Corporation, Attn:
Customer Experience, 5900 Parretta Drive, Kansas City, MO 64120.
Bluetooth License
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of
such marks by Midland is under license. Other trademarks and trade names are those of their
respective owners. The product is compliant with and adopts the Bluetooth® Specification
and has successfully passed all interoperability tests that are specified in the Bluetooth®
specification. However, interoperability between the device and other Bluetooth®- enabled
products is not guaranteed.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Midland BTR1 Advanced Mode d'emploi

BTR1 Advanced
Midland
Marque
Midland
Modèle
BTR1 Advanced
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents