Dometic 4301 Manuel utilisateur

FAN-TASTIC VENT

FAN

WARNING

Cancer and Reproductive Harm

www.P65Warnings.ca.gov

100%

85%

70%

55%

40%

25%

10%

Manua uto

Speed Temp

Air In

Air Out

Down

Up

Rain

Sensor

90/33

85/30

80/27

75/24

70/21

65/18

60/15

Al

3300, 3350, 4100, 4150, 4175, 4200 RJ-11, 4201, 4251, 4301, 4351

5200, 5250, 5300, 5350, 6300, 6350, 7300, 7350

EN Fan-Tastic Vent Fans and Controls

Installation and Operation Manual ........2

FR Ventilateurs d’extraction et

commandes Fan-Tastic

Manuel d’installation et d’utilisation .... 27

ES Ventiladores de circulación y

controles Fan-Tastic

Manual de instalación y funcionamiento .. 53

Attention Consumers: This product is intended to replace an

existing vent fan in your RV. If you are creating a new installation

or planning a more complicated project, please consult a

qualiﬁed service professional.

The installation location

should be:

• 14.5 x 14.5 in.

(368 x 368 mm) To create or adjust the opening,

consult a qualiﬁed service

professional.

• 4 in. (102 mm)

depth or greater Contact Dometic for location

depths less than 4 in.

• Non-corrugated Create a level platform or consult a

qualiﬁed professional.

• Level Create a level platform or consult a

qualiﬁed professional.

https://manual-hub.com/

2EN

Contents

Service Center & Dealer Locations

Visit: www.dometic.com

Read these instructions carefully. These instructions

MUST stay with this product.

Contents

1 Explanation of Symbols and Safety

Instructions ............................ 2

2 Pre-Installation ......................... 3

3 Installation ............................. 9

4 Vent Fan Operation ..................... 14

5 Control Operation ...................... 15

6 Maintenance ..........................22

7 Troubleshooting .......................25

8 Disposal ..............................26

Limited Warranty .........................26

1 Explanation of Symbols and

Safety Instructions

This manual has safety information and instructions to

help you eliminate or reduce the risk of accidents and

injuries.

1.1 Recognize Safety Information

This is the safety alert symbol. It is used to alert

you to potential physical injury hazards. Obey all

safety messages that follow this symbol to avoid

possible injury or death.

1.2 Understand Signal Words

A signal word will identify safety messages and property

damage messages, and also will indicate the degree or

level of hazard seriousness.

DANGER!

Indicates a hazardous situation that, if not avoided,

will result in death or serious injury.

WARNING

Indicates a hazardous situation that, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a hazardous situation that, if not avoided,

could result in minor or moderate injury.

NOTICE: Used to address practices not related to

physical injury.

IIndicates additional information that is not related

to physical injury.

1.3 Supplemental Directives

To reduce the risk of accidents and injuries, please

observe the following directives before proceeding to

install or operate this appliance:

• Read and follow all safety information and

instructions.

• Read and understand all instructions before installing

or operating this product.

• The installation must comply with all applicable local

or national codes, including the latest edition of the

following standards:

U.S.A.

– ANSI/NFPA70, National Electrical Code (NEC)

– ANSI/NFPA 1192, Recreational Vehicles Code

– ANSI Z21.57, Recreational Vehicles Code

Canada

– CSA C22.1, Parts l & ll, Canadian Electrical Code

– CSA Z240 RV Series, Recreational Vehicles

Fan-Tastic Vent Fan

https://manual-hub.com/

3

EN

Pre-Installation

1.4 Personal and Product Safety

WARNING: FALL HAZARD.

Vent fans are normally located on the roof of a

recreational vehicle (RV). It is inherently dangerous

to climb onto the roof of an RV to perform

installation, maintenance, or repairs on a vent fan.

Use care and take appropriate precautions when

climbing onto the roof of an RV, when working on

the roof of an RV, or when standing on a ladder to

work on an RV. Failure to obey this warning could

result in death or serious injury.

NOTICE: Failure to adhere to the instructions in the

following statements could result in personal, product,

and/or property damage.

• If you are not familiar with how to perform the

installations in this manual, consult a qualiﬁed

installer.

• Use only Dometic replacement parts and

components that are speciﬁcally approved for use

with the appliance.

• Avoid improper installation, adjustment, alterations,

service, or maintenance of the vent fan.

• Do not modify this product in any way. Modiﬁcation

can be extremely hazardous.

2 Pre-Installation

This section provides product information, including

speciﬁcations, to help you prepare to install your new

Fan-Tastic Vent Fan.

IThe images are for reference purposes only. Parts

and part locations may vary according to speciﬁc

product models. Measurements may vary ±0.38 in.

(10 mm).

2.1 Intended Use

The Dometic Fan-Tastic Vent Fan (“vent fan”) is a roof

ventilation system designed for use in RVs to allow

maximum airﬂow and additional protection from the

elements while using a vented opening. In addition to

speed settings and manual or automatic lid operation,

options may include a rain sensor to stop the vent fan

and close the lid when it senses moisture.

The manufacturer accepts no liability for damage in the

following cases:

• Faulty assembly or connection

• Damage to the product resulting from mechanical

inﬂuences and excess voltage

• Alterations to the product without express permission

from the manufacturer

• Use for purposes other than those described in the

operating manual

Dometic Corporation reserves the right to modify

appearances and speciﬁcations without notice.

Fan-Tastic Vent Fan

https://manual-hub.com/

4EN

Pre-Installation

2.2 Package Contents

This section shows the package contents provided with

the vent fan models. Actual package contents may vary.

Refer to the complete parts list (available online at

www.dometic.com) for additional information.

Package Contents

(AA)

Fan-Tastic Vent Fan

(BB)

Gasket or Sealer

(CC)

6 in. (152 mm) Trim Garnish3

(DD)

#8 Self-Tapping Flat-Head Screws

(3/4”–1”)

[x16]

(EE)

#8 Flat-Head Screws (3/8”)

[x4]

(FF)

16 Gauge Stranded Copper Wire

(GG)

Insulated Butt-Splice Wire Connectors

[x2]

(HH)

White Wire = Negative or Ground

(JJ)

Black Wire = Positive or Fused

100%

85%

70%

55%

40%

25%

10%

Manuauto

Speed Temp

Air In

Air Out

Down

Up

Rain

Sensor

90/33

85/30

80/27

75/24

70/21

65/18

60/15

Al

+-

(KK)

Remote Control with Cradle1

(LL)

AA Batteries1

[x2]

(NN)

Wall Control2

1Models: 7350, 7300, 6300, and 6350 only.

2Models: 7350, 7300, 6350, 6300, 5350, 5300, 5250, 5200, and 4200 only.

3To install a clamp-style fan using a clamp-mount method for roofs or walls < 4 in. (102 mm) thick, you will need a diﬀerent trim

garnish. Review “Model Identiﬁcation” on page5 and then contact your local Dometic service partner or dealer or the

Dometic Customer Support Center at 800-544-4881.

Fan-Tastic Vent Fan

https://manual-hub.com/

5

EN

Pre-Installation

2.3 Model Identiﬁcation

This section provides the two possible locations to

ﬁnd the vent fan model identiﬁcation label. Have the

information from this label ready, if contacting Dometic

for service.

ISome models may not be available at all times.

q

w

1 Model ID Label Locations

q Model ID location

(older models)

w Barcode location

(current models)

2.4 Vent Fan Dimensions

q

w

2 Vent Fan Dimensions

q 14 in. (356 mm) w 14 in. (356 mm)

2.5 Vent Fan Cut-out Dimensions

q

w

3 Vent Fan Cut-out Dimensions

q 14.5 in. (368 mm) w 14.5 in. (368 mm)

Fan-Tastic Vent Fan

https://manual-hub.com/

6EN

Pre-Installation

2.6 Trim Garnish Dimensions

This section provides the cutting measurements for the

interior ceiling trim garnish.

A 6 in. (152 mm) trim garnish (CC) for a standard

installation is provided with your vent fan. Thinner roofs

or walls require a diﬀerent trim garnish and a diﬀerent

type of installation.

ITo request a trim garnish for a thinner roof or clamp-

fan installation, review “Model Identiﬁcation” on

page5 and then contact your local Dometic

service partner or dealer or the Dometic Customer

Support Center at 800-544-4881.

2.6.1 Opening Depth:7/8to1-7/8in.

(22to48 mm)

For a roof or wall thickness from 7/8 in. (22 mm) to

1-7/8in. (48 mm), use a 1-7/8 in. (48 mm) trim garnish

and adjust the size according to the table below.

ITo request the correct trim garnish, contact

your local Dometic service partner or dealer

or the Dometic Customer Support Center at

800-544-4881.

Roof

or Wall

Thickness

Recommend

Trim Garnish

Size

Minimum

Trim Garnish

Size

Recommend

Screw Size*

Maximum

Screw Size*

7/8 in.

(22 mm)

7/8 in.

(22 mm)

1/2 in.

(13 mm)

1-1/4 in.

(32 mm)

1-7/8 in.

(48 mm)

1 in.

(25 mm)

1 in.

(25 mm)

3/4 in.

(19 mm)

1-1/2 in.

(38 mm)

2 in.

(51 mm)

1-1/4 in.

(32 mm)

1-1/4 in.

(32 mm)

1 in.

(25 mm)

1-3/4 in.

(45 mm)

2-1/4 in.

(57 mm)

1-1/2 in.

(38 mm)

1-1/2 in.

(38 mm)

1-1/4 in.

(32 mm)

2 in.

(51 mm)

2-1/2 in.

(64 mm)

1-3/4 in.

(45 mm)

1-3/4 in.

(45 mm)

1-1/2 in.

(38 mm)

2-1/4in.

(57 mm)

2-3/4 in.

(70 mm)

1-7/8 in.

(48 mm)

1-7/8 in.

(48 mm)

1-5/8 in.

(41 mm)

2-1/4in.

(57 mm)

2-3/4 in.

(70 mm)

*These recommended screw sizes are for a clamp-fan

installation only.

2.6.2 Opening Depth:2to4in.

(51to102mm)

For a roof or wall thickness from 2 in. (51 mm) to 4in.

(102 mm), use a 4-1/4 in. (108 mm) trim garnish and

adjust the size according to the table below.

ITo request the correct trim garnish, contact

your local Dometic service partner or dealer

or the Dometic Customer Support Center at

800-544-4881.

Roof

or Wall

Thickness

Recommend

Trim Garnish

Size

Minimum

Trim Garnish

Size

Recommend

Screw Size*

Maximum

Screw Size*

2 in.

(51 mm)

2 in.

(51 mm)

1-3/4 in.

(45 mm)

2-1/2 in.

(64 mm)

3 in.

(76 mm)

2-1/4 in.

(57 mm)

2-1/4 in.

(57 mm)

2 in.

(51 mm)

2-3/4 in.

(70 mm)

3-1/4 in.

(83 mm)

2-1/2 in.

(64 mm)

2-1/2 in.

(64 mm)

2-1/4 in.

(57 mm)

3 in.

(76 mm)

3-1/2 in.

(89 mm)

2-3/4 in.

(70 mm)

2-3/4 in.

(70 mm)

2-1/2 in.

(64 mm)

3-1/4 in.

(83 mm)

3-3/4 in.

(95 mm)

3 in.

(76 mm)

3 in.

(76 mm)

2-3/4 in.

(70 mm)

3-1/2 in.

(89 mm)

4 in.

(102 mm)

3-1/4 in.

(83 mm)

3-1/4 in.

(83 mm)

3 in.

(76 mm)

3-3/4 in.

(95 mm)

4-1/4 in.

(108 mm)

3-1/2 in.

(89 mm)

3-1/2 in.

(89 mm)

3-1/4 in.

(83 mm)

4 in.

(102 mm)

4-1/2 in.

(114 mm)

3-3/4 in.

(95 mm)

3-3/4 in.

(95 mm)

3-1/2 in.

(89 mm)

4-1/4 in.

(108 mm)

4-3/4 in.

(121 mm)

4 in.

(102 mm)

4 in.

(102 mm)

3-3/4 in.

(95 mm)

4-1/2 in.

(114 mm)

5 in.

(127 mm)

*These recommended screw sizes are for a clamp-fan

installation only.

Fan-Tastic Vent Fan

https://manual-hub.com/

7

EN

Pre-Installation

2.6.3 Opening Depth:4.25to6 in.

(108to152mm)

For a roof or wall thickness from 4-1/4 in. (108 mm)

to 6 in. (152 mm), use the 6 in. (152 mm) trim garnish

included with your Fan-Tastic Vent Fan and adjust the size

according to the table below.

Roof or Wall

Thickness

Recommend

Trim Garnish Size

Minimum

Trim Garnish Size

4-1/4 in. (108 mm) 4-1/4 in. (108 mm) 4.0 in. (102 mm)

4-1/2 in. (114 mm) 4-1/2 in. (114 mm) 4-1/4 in. (108 mm)

4-3/4 in. (121 mm) 4-3/4 in. (121 mm)

4-1/2 in. (114 mm)

5 in. (127 mm) 5 in. (127 mm)

4-3/4 in. (121 mm)

5-1/4 in. (140 mm) 5-1/4 in. (140 mm) 5 in. (127 mm)

5-1/2 in. (140 mm) 5-1/2 in. (140 mm)

5-1/4 in. (140 mm)

5-3/4 in. (146 mm) 5-3/4 in. (146 mm) 5-1/2 in. (140 mm)

6 in. (152 mm) 6 in.* (152 mm)

5-3/4 in. (146 mm)

*The 6.0 in. trim garnish is just long enough to provide

coverage to the leading edge of the screen assembly,

overlapping by 1/16 in. and not the recommended 1/8 in.

2.7 Wiring Diagram

This section provides the 12 VDC wiring connection for

the vent fan.

q

w

e

r

t

4 Wiring Diagram

q White (Ground) r Supply Ground

w Red (+) t Supply Power

e Black (+)

2.8 Installation Requirements

This manual will help you replace an existing vent or vent

fan. If you encounter one of the following items, please

contact a qualiﬁed service professional.

• If the existing vent opening is not 14-1/2x14-1/2in.

(368 x 368 mm), you may need to resize the

opening.

• If there is no existing vent, you will need to create

a new 14-1/2 in. x 14-1/2 in. (368 mm x 368 mm)

opening.

• If the roof is corrugated or not level, you may need to

create and install a frame to provide a level platform

for the new vent fan.

Fan-Tastic Vent Fan

https://manual-hub.com/

8EN

Pre-Installation

2.9 Required Speciﬁcations

This section provides the operational speciﬁcations for

the vent fan and control.

Weight 12.0 lbs (5.4 kg)

Power Consumption 36 W

Output <3 A

Fan Height 4 in. (101 mm) standard

2.10 Tools and Materials

Dometic recommends the following tools and materials

to install the product:

Recommended Tools and Materials (not included)

Straight Edge Pencil or Pen 16-Gauge Stranded

Copper Wire (Minimum)

All-Weather Roof Sealant EPDM-Compatible Roof Sealant Utility Knife

Level Standard #2 Phillips Screwdriver Cordless Drill with 1/8 in. Drill Bit

Putty Knife or Scraper Measuring Tape Multimeter

OR

Screw Gun Wire Cutter/Stripper/Crimping Tool #8 x 3/8 in. Screws (x2) or

Removable Hanging Strip

(for the Remote Control Cradle)

Fan-Tastic Vent Fan

https://manual-hub.com/

9

EN

Installation

3 Installation

WARNING: FIRE OR ELECTRICAL SHOCK

HAZARD. Failure to obey these warnings

could result in death or serious injury.

• This product is designed for 12 VDC use only. Do not

connect the vent fan to 110 VAC.

• Shut oﬀ the gas supply, disconnect the 120 VAC

power from the RV, and disconnect the positive

(+) 12VDC terminal from the supply battery before

drilling, cutting into, or wiring the RV.

NOTICE: The vent fan is designed to run on ﬁltered DC

current. Do not connect the vent fan to unﬁltered DC

current. Doing so could result in circuit board damage or

failure.

This section describes how to install a vent fan

horizontally on an RV roof, or vertically on an exterior wall

with minor modiﬁcations.

3.1 Removing the Existing Vent

q

w

er

5 Remove the Existing Vent

q Existing Vent e Screw Holes

w Existing Screws r Sealant

1. Unscrew and remove the existing roof vent.

2. Remove any caulking compound around the roof

or wall opening. A clean surface oﬀers a better

seal. Consult your RV owner’s manual for cleaning

recommendations.

3. Seal any screw holes and seams where the roof

gasket will be located, using a good grade of

all-weather roof sealant.

3.2 Assessing the Trim Garnish

1. Determine the length, width, and thickness or depth

of the roof or wall opening where the new fan vent

will be installed.

2. Conﬁrm you have the correct trim garnish for the

depth of the roof or wall opening. See “Trim Garnish

Dimensions” on page6.

q

w

CC

e

6 Resizing the Trim Garnish

q Required Trim Garnish

Height

e Utility Knife

w Excess Trim Garnish to

Remove

3. Use a utility knife to adjust the size of the trim garnish

(CC) to the correct height, if necessary.

a. Use a straight edge and a pen to mark horizontally

around all four sides from the top edge. Score the

marked lines.

b. Cut from the top edge of the corners at a 45

degree angle down to the score line, then break

the excess plastic away from the trim garnish (CC).

3.3 Assessing the Roof Structure

NOTICE: If you are not using an existing 14.5 in. x

14.5in. (368 mm x 368 mm) vent opening for your vent

fan, see “Installation Requirements” on page7.

Fan-Tastic Vent Fan

https://manual-hub.com/

10 EN

Installation

q

w

7 Structural Integrity for the Roof

q Incorrect installation w Correct installation

Make sure the roof opening does not compromise the

structural integrity of the roof or wall.

• Do not cut the structure or the raers.

• The raers should remain supported by a cross beam.

• The roof opening should be between the raers.

3.4 Framing the Roof or Wall

Opening

If the roof is corrugated or not level, complete this

section to create a level platform or contact a qualiﬁed

service professional.

q

w

8 Frame for a Roof Opening

q 0.75 in.

(25 mm)

w 0.25 in. (6 mm) Opening for

the Power Supply Wiring

1. Build a frame for the vent opening to provide a level

platform for securing the mounting ﬂange to the roof.

2. Leave access for the power supply wiring to pass into

the interior through the frame.

3.5 Connecting the Power

IIf you are replacing an existing vent fan, use the

existing wiring only if it meets the Recreation

Vehicle Industry Association’s 16 AWG wiring and

location requirements.

This section describes how to connect the vent fan to a

12 VDC power source.

1. Locate the nearest 12 VDC power source wiring.

2. To avoid blowing the fuse, test the power source

wiring for polarity.

a. Turn on the 12 VDC power or battery.

b. Using a multimeter, touch the red lead to the

positive source. At the same time, touch the black

lead to the neutral or negative wire. A correct

polarity will display +12 or more volts. If incorrect,

the multimeter will display -12 volts or more.

c. Turn oﬀ the 12 VDC power or battery.

q

9 Power Supply at the Roof Opening

q 6 in. (152 mm) minimum

3. Route the power source wiring to the roof or wall

opening. Add an additional 15 in. (381 mm) of

wire, to ensure an easy connection to the vent

fan. If necessary, extend the vent fan’s wiring using

the additional lengths of black and white wiring

provided.

Fan-Tastic Vent Fan

https://manual-hub.com/

11

EN

Installation

e r

qw

GG

10 Connect the Vent Fan Wiring to the Power Source Wiring

q White Vent Fan Wire

(Neutral or Ground)

e Black Vent Fan Wire

(Positive or Fused)

w Power Source Wiring

(Neutral or Ground)

r Power Source Wiring

(Positive or Fused)

4. Use the butt-slice connectors (GG) to connect the

vent fan’s:

a. black wire to the positive 12VDC power source

wire.

b. white wire to the neutral or ground.

5. Crimp the butt-slice connector (GG) ends to secure

the connection.

3.6 Mounting the Vent Fan

This section describes the two installation options for

your vent fan.

• A vent mount installation is the standard,

recommended method for most Fan-Tastic Vent Fans.

See “Vent Mount” on page11.

• A clamp-fan mount is recommended only for a roof

or wall that is less than 4 in. (102 mm) thick and

without a solid substrate to support a rooop screw

installation. See “Clamp-Fan Mount” on page12.

• Conﬁrm the height of the trim garnish is correct for

the thickness of your roof or wall. See “Trim Garnish

Dimensions” on page6.

3.6.1 Vent Mount

This section describes how to install a vent fan using the

vent mount method.

r

AA

BB

q

w

e

DD

11 Vent Mounting

q All-Weather Sealant e Mounting Flange

w Vent Fan Hinge r Exterior

1. Move the vent fan (AA) to the exterior roof opening.

2. Line the outside of the roof opening with a

compatible sealant, or place the gasket (BB) around

the opening.

IIf using sealant, for rubber roofs, use an EPDM-

compatible roof sealant.

3. Position the vent fan (AA) over the exterior roof

opening, making sure the sealant or gasket is

“sandwiched” between the bottom of the mounting

ﬂange and the roof opening.

– When positioning the vent fan on the roof, the lid

hinge should be closest to the front of the RV.

– If positioning the vent fan on the side of the RV

(vertically), the lid hinge should be closest to and

parallel with the roof line.

4. Use the #8 self-tapping ﬂat-head screws

(3/4”–1”) (DD) provided to attach the vent fan to the

exterior roof opening.

5. Apply an all-weather sealant over the screw heads and

at the mounting ﬂange where it meets the roof or side.

Fan-Tastic Vent Fan

https://manual-hub.com/

12 EN

Installation

e

q

EE

CC

w

12 Securing the Trim Garnish for a Vent Mount

q Ceiling e Interior

w Fan Base

6. From the interior of the RV, use the #8 ﬂat-head

screws (3/8”) (EE) provided to mount the trim garnish

(CC) into the fan base. Do not overtighten the screws.

IThe four screw holes are located on the outside

corners on the larger vent mount trim garnish

(provided).

7. Using a screw gun, torque the #8 ﬂat-head screws

(EE) equally. Do not overtighten.

3.6.2 Clamp-Fan Mount

This section describes how to install a vent fan using the

clamp-fan method.

Some Fan-Tastic Vent Fans are available in a “clamp fan”

conﬁguration for roof or wall openings with a thickness

less than 4 in. (102 mm). The shorter trim garnish for a

clamp-fan mount is designed to secure the vent fan with

screws into the fan base from inside the RV and to trim

the ceiling cut-out.

r

AA

w

q

e

13 Clamp-Fan Mounting

q All-Weather Sealant e Mounting Flange

w Vent Fan Hinge r Exterior

1. Move the vent fan (AA) to the exterior roof or wall

opening.

2. Run a double-bead of compatible sealant between

the outside of the roof or wall opening and the base

of the mounting ﬂange.

IDo not use putty tape, butyl, or gaskets for clamp-fan

mounts.

q

r

e

w

14 Securing the Trim Garnish for a Clamp-Fan Mount

q Ceiling e Shorter Trim Garnish

w Fan Base r #8 Flat-Head Screws

Fan-Tastic Vent Fan

https://manual-hub.com/

13

EN

Installation

3. From the interior of the RV, use four #8 ﬂat-head

screws (not provided) to mount the trim garnish

into the fan base. Do not overtighten the screws.

See “Trim Garnish Dimensions” on page6 for

recommended screw length.

IThe four screw holes are located on the inside

corners of the shorter trim garnish (not provided).

4. Using a screw gun, torque the #10 ﬂat-head screws

equally. Do not overtighten.

IIf using sealant, for rubber roofs, use an EPDM-

compatible roof sealant.

3.7 Mounting the Controls

This section describes how to install your vent fan controls.

3.7.1 Mounting the Remote Control

Cradle

This section describes two options to install a cradle

for those models equipped with a remote control. The

cradle installation is optional.

q

w

(Front) (Rear)

KK

15 Remote Control Cradle

q #8 x 3/8" screws w Removable Hanging Strip

• Option 1: Hold the back of the cradle (KK) to the wall

location and secure it with two #8 x 3/8" screws (not

included) through the two round holes in the back.

• Option 2: Aﬃx the cradle (KK) to the wall location

using a removable, hanging strip (not included) that

is safe for your RV interior according to your owner’s

manual.

3.7.2 Mounting the Wall Controls

w

e

r

t

NN

q

16 Wall Control

q Notch r Front

w RJ-11 control cable t Back

e #8 x 3/8” screws

1. Locate the notch on the bottom edge of the wall

control (NN) and use a screwdriver or a coin in a

twisting motion to separate the back plate.

2. Thread the RJ-11 control cable (in the wall) through the

square hole in the back plate (from the backside to

the front) and plug it into the front half of the control.

3. Hold the back plate to the wall location and secure it

with two #8 x 3/8” screws (not included) through the

two round holes in the back plate.

Fan-Tastic Vent Fan

https://manual-hub.com/

14 EN

Vent Fan Operation

4. Push the front half of the wall control (NN) onto the

back plate, being sure to align the connector plug

with the square hole, and snap both halves together.

4 Vent Fan Operation

CAUTION: WATER DAMAGE/LEAK HAZARD.

Failure to obey the following instructions

could result in minor or moderate injury or

property damage:

• Do not leave the vent lid open and unattended for

extended periods of time, or under unusual weather

conditions that may result in leakage and serious

damage.

• Do not use this product in inclement weather.

CAUTION: PINCH HAZARD.

Do not pull down on the vent fan knob. Failure to

obey this caution could result in minor or moderate

injury or property damage.

ISlightly open the windows on the shaded side of

the RV to provide the most comfortable ambient air,

even on hot days.

IDirect the airﬂow by opening a window. Try to

position yourself between an open window and the

fan for greatest airﬂow comfort.

IFor optimal performance, close all the outside vents

when using your vent fan.

IIf driving while the vent is open, keep it fully open

to avoid ﬂuttering or closing unexpectedly.

This section describes the options available to li

the vent lid and to operate the vent, the fan, and the

thermostat.

4.1 Opening the Manual-Li Vent

q

17 Manual Li

q Hand-Knob

To manually open or close the lid on your vent fan, grasp

the black hand-knob and turn it in the direction desired.

4.2 Operating the Automatic-Li

Vent

q

18 Automatic Li

q Three-Speed Knob

1. Use the UP/DOWN button(s) on the wall control to

open or close the vent lid. Open the vent lid 4 in.

(102 mm) or more. Some fan models have a built-in

switch that will not allow the fan motor to operate

unless the vent lid is partially open. See “Control

Operation” on page15 for your vent fan model.

2. With the vent open, turn the three-speed knob on the

fan to the desired performance level: 0-OFF, 1-LOW,

2-MEDIUM, 3-HIGH, or select the speed on the wall

controller. See “Using the Premium Remote and Wall

Controls” on page16 through 23.

Fan-Tastic Vent Fan

https://manual-hub.com/

15

EN

Control Operation

3. For increased airﬂow, open the window or door

farthest from the vent.

4.3 Operating the Thermostat

With the vent lid open, select the desired temperature or

comfort level on the thermostat. The fan motor will start and

stop automatically as the interior temperature of the coach

exceeds or drops below the selected temperature level.

See “Using the Premium Remote and Wall Controls” on

page16.

4.4 Operating the Reverse Switch

This section describes how to change the vent fan’s air

ﬂow direction, either to pull air into or expel air from, the

RV interior.

q

19 Reverse Switch

q Fan Motor Switch

1. With the vent open, move the fan motor switch to the

center position to turn the fan OFF. Wait for the fan

blades to stop moving.

2. Select the IN position on the switch to bring air from

the roof area into your RV (pressurizes inside), or

select the OUT position to bring air in through any RV

openings, and expel the air out through the roof.

5 Control Operation

CAUTION: WATER DAMAGE/LEAK HAZARD.

Failure to obey the following instructions

could result in minor or moderate injury or

property damage:

• Do not leave the vent lid open and unattended for

extended periods of time, or under unusual weather

conditions that may result in leakage and serious

damage.

• Do not use this product in inclement weather.

CAUTION: PINCH HAZARD.

Do not pull down on the vent fan knob. Doing so

could damage your fan or cause physical injury.

Failure to obey this caution could result in minor or

moderate injury or property damage.

This section describes how operate the vent fan models.

In addition, the following suggestions will improve your

vent fan’s overall operation .

• Close all outside vents when using your vent fan.

• Slightly open the windows on the shaded side of the

RV to provide the most comfortable ambient air, even

on hot days.

• Direct the airﬂow by opening a window. Try to

position yourself between an open window and the

fan for greatest airﬂow comfort.

• If driving while the vent is open, keep it fully open to

avoid ﬂuttering or closing unexpectedly.

Fan-Tastic Vent Fan

https://manual-hub.com/

16 EN

Control Operation

5.1 Using the Premium Remote and

Wall Controls

IFor Models 6300, 6350, 7300, and 7350

IRemote and wall controls operate identically.

100%

85%

70%

55%

40%

25%

10%

Manua uto

Speed Temp

Air In

Air Out

Down

Up

Rain

Sensor

90/33

85/30

80/27

75/24

70/21

65/18

60/15

Al

100%

85%

70%

55%

40%

25%

10%

Manua uto

Speed Temp

Down

Up

Rain

Sensor

90/33

85/30

80/27

75/24

70/21

65/18

60/15

Al

6300, 7300 6350, 7350

20 Premium Remote Wall Controls

Name Function

Fan Power ON/OFF Press to turn ON the fan (this will start the fan in Auto mode).

Press to turn OFF the fan (this will stop the fan and close the lid).

Speed Fan Speed

Press UP to increase the fan speed.

Press DOWN to decrease the fan speed.

• Pressing either button will change fan mode to Manual.

• These buttons work in Manual mode only. The fan has 13 speeds. Fan speed is

indicated on the remote in % from 10% (low speed) to 100% (high speed). An LED

will illuminate next to the % of fan speed. If two LEDs are illuminated, then the speed

is halfway between the illuminated %. For example, if both 85% and 100% LEDs are

illuminated; the speed is approximately 93%.

Temp

Thermostat

Temperature Setting:

Fahrenheit/Celsius

Press UP to increase the Set Temperature.

Press DOWN to decrease the Set Temperature.

• Pressing either button will change fan mode to Auto.

• These buttons work in Auto mode only. The fan has 13 temperature settings; the

temperature setting is indicated on the remote in degrees (60 °F–90°F;

15°C–30°C). An LED will illuminate next to the degrees setting of the thermostat. If

two LEDs are illuminated, the thermostat setting is halfway between the illuminated

degrees. For example, if both the 85/30 and 90/33 LEDs are illuminated; the

setting is approximately 88 °F (31 °C).

Down

Up

Vent Lid OPEN/CLOSE

When the vent lid is closed, press this button once to open the vent lid.

When the vent lid is open, press this button once to close the vent lid.

• This button will operate independently of the fan motor ON/OFF switch.

• Pressing this button will not change the fan mode. The rain sensor can be turned ON

or OFF by pressing the button for three seconds.

Air In

Air Out

Air OUT/IN

(Model 6350 & 7350)

In either Manual or Auto mode (when the vent lid is open), press this button once to

reverse the fan blade direction. Press it again for the opposite direction. Pressing the

button will not change the fan mode.

Fan-Tastic Vent Fan

https://manual-hub.com/

17

EN

Control Operation

Name Function

Rain

O

Sensor Rain Sensor and

Rain Sensor LED

Turn the rain sensor ON/OFF by pressing the Rain Sensor UP/DOWN button for three

seconds. This LED will illuminate when the rain sensor has been turned OFF.

Manual

Manual Mode LED Press the Speed UP/DOWN to enter Manual mode. This LED will illuminate when the

controls are in Manual mode.

Auto

Auto Mode LED Press the Temp UP/DOWN to enter Auto mode. This LED will illuminate when the

controls are in Auto mode.

IWireless remote-control models (7300 & 7350)

will “sleep” or shut oﬀ 30 seconds aer the last

command, to preserve battery life. To “wake” the

control, push any button on the control, and it will

show the last temperature and/or speed setting

received. If the control is manually shut oﬀ using the

ON/OFF button, it will reset.

IIf a command is not allowed, the control will beep

twice.

Fan-Tastic Vent Fan

https://manual-hub.com/

18 EN

Control Operation

5.2 Using Wall-Mounted Controls

IFor Models 5300, 5350

5300 5350

21 Wall-Mounted Controls (5300, 5350)

IWhen the fan is running: Closing the lid by pressing

the UP/DOWN button shuts OFF the fan blade.

Re-opening the lid using the UP/DOWN button

will revert the fan blade movement to its previous

set speed. Using the ON/OFF button will not do

this; the ON/OFF button resets the fan to normal

operation.

Name Function

Fan Power ON/OFF Press to turn ON the fan. This will start the fan on HIGH.

Press to turn OFF the fan. This will stop the fan and close the lid.

Fan Speed Press UP to increase the fan speed.

Press DOWN to decrease the fan speed. The fan has 13 speeds, not including OFF.

Vent Lid OPEN/CLOSE

(Model 5350)

When the vent lid is closed, press this button once to open the vent lid.

When the vent lid is open, press this button once to close the lid.

The rain sensor can be turned ON or OFF by pressing this button for three seconds.

Vent Lid OPEN/CLOSE

(Model 5300)

When the vent lid is closed, press the UP button once to open the vent lid.

When the vent lid is open, press the DOWN button once to close the vent lid.

The rain sensor can be turned ON or OFF by pressing this button for three seconds.

Air OUT/IN

(Model 5300)

When the vent lid is open, press this button once to reverse the fan blade direction;

press it again for the opposite direction.

• Once pressed, the motor will slow and then reverse direction. If the button is

pressed again during the reversing cycle, a double-beep will indicate the cycle is in

progress.

• The function can only be changed aer the reversing cycle is complete.

Rain Sensor LED

This LED will illuminate when the rain sensor has been turned OFF at the wall control.

The rain sensor can be turned ON or OFF by pressing the DOWN button for three

seconds.

Fan-Tastic Vent Fan

https://manual-hub.com/

19

EN

Control Operation

5.3 Using Wall-Mounted Controls

IFor Models 5200, 5250 RJ-11

5200 5250

22 Wall-Mounted Controls (5200, 5250)

IWhen the fan is running: Closing the lid by using

the UP/DOWN button shuts OFF the fan blades.

Re-opening the lid by using the UP/DOWN button

will revert the fan blade movement to its previous

set speed. Using the ON/OFF button will not do

this; the ON/OFF button resets the fan to normal

operation.

Name Function

Fan Power ON/OFF Press to turn ON the fan. This will start the fan on HIGH.

Press to turn OFF the fan. This will stop the fan and close the lid.

Fan Speed Press UP to increase the fan speed.

Press DOWN to decrease the fan speed. The fan has 13 speeds, not including OFF.

Vent Lid OPEN/CLOSE

(Model 5250)

When the vent lid is closed, press this button once to open the lid.

When the vent lid is open, press this button once to close the lid.

Vent Lid OPEN/CLOSE

(Model 5200)

When the vent lid is closed, press the UP button once to open the lid.

When the vent lid is open, press the DOWN button once to close the lid.

Air OUT/IN

(Model 5250)

When the vent lid is open, press this button once to reverse the fan blade direction;

press it again for the opposite direction.

Fan-Tastic Vent Fan

https://manual-hub.com/

20 EN

Control Operation

5.4 Using Wall-Mounted Controls

IFor Model 4200 RJ-11

23 Wall-Mounted Control (4200)

IWhen the fan is running: Closing the lid by using

the UP/DOWN button shuts the fan blades OFF.

Re-opening the lid using the UP/DOWN button will

revert the fan speed to its previous set speed. Using

the ON/OFF button will not do this; the ON/OFF

button resets the fan to normal operation.

Name Function

Fan ON 1-2-3

Press to turn ON the fan.

Each press will increase the fan speed one level:

• One press - turns the fan ON and opens the vent lid at lowest level speed

• Two presses - changes fan to level-2 speed

• Three presses - changes fan to level-3 speed

• Four presses - returns fan to level-1 speed

Fan Power OFF Press to turn OFF the fan.

• This will stop the fan and close the lid.

Vent Lid OPEN/CLOSE When the vent lid is closed, press the button once to open the lid.

When the vent lid is open, press this button once to close the lid.

Fan-Tastic Vent Fan

https://manual-hub.com/

La page charge ...

Dometic 4301 Manuel utilisateur

Dometic 4301 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents