Axis Communications 18613 Manuel utilisateur

ENGLISH

FRANCAIS

DEUTSCH

ESPAÑOL

ITALIANO

AXIS 216FD

AXIS 216FD-V

AXIS 216MFD

AXIS 216MFD-V

Fixed Dome Network Camera

Installation Guide

AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide Page 3

ENGLISH

AXIS 216FD/216FD-V

AXIS 216MFD/216MFD-V

Installation Guide

This installation guide provides instructions for installing the AXIS 216FD, AXIS 216FD-V,

AXIS 216MFD and AXIS 216MFD-V Fixed Network Dome Camera on your network. For all

other aspects of using the product, please see the User’s Manual, available on the CD

included in this package, or from www.axis.com/techsup

Installation steps

1. Check the package contents against the list below.

2. Hardware overview. See page 4.

3. Install the hardware. See page 5.

4. Assign an IP address. See page 7.

5. Set the password. See page 10.

6. Adjust the focus. See page 11.

7. Complete the installation. See page 11.

Package contents

Item Models/variants/notes

Fixed Dome Network camera AXIS 216FD: tamper-resistant casing

AXIS 216FD-V: vandal-resistant casing

AXIS 216MFD: tamper-resistant casing

AXIS 216MFD-V: vandal-resistant casing

PS-H indoor power supply

(country specific)

Europe

UK

Australia

USA/Japan

Argentina

Korea

Power supply extension cable 1.8 meters

Terminal block connector 4-pin connector block for connecting external devices to the I/O terminal

connector

Mounting kit Screwdriver for tamper-proof screws

Tamper-proof screws

Drill template

CD AXIS Network Video Product CD, including product documentation,

installation tools and other software

Printed Materials AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide (this document)

Axis Warranty Document

Important!

This product must be used in

compliance with local laws

and regulations.

Page 4 AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide

Hardware overview

Product ID & Serial number (S/N).

The serial number may be

required during the installation.

Dimensions

HxWxD = 94 x 144 x 132mm (3.7" x 5.7" x 5.2")

Weight AXIS 216FD/AXIS 216MFD = 425g (0.94 lb) (power supply not included)

Weight AXIS 216FD-V/216MFD-V = 580g (1.28 lb) (power supply not included)

Cover plates

Network

indicator LED

Status indicator LED

Control button

Power connector

(see page 14)

Network

connector

(see page 14)

I/O terminal connector

(see page 14)

Power

indicator LED

Audio out

Audio in

Microphone

16mm cable conduit

(not supplied) fitted to

AXIS 216FD-V/216MFD-V

AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide Page 5

ENGLISH

Install the hardware

Mount the camera

The AXIS 216FD/216FD-V/216MFD/216MFD-V can be mounted with the cables routed

through the wall/ceiling, or from above or below. There are cover plates for the openings on

both sides of the dome cover. The AXIS 216FD-V/216MFD-V can also be fitted with a metal

conduit for protecting the cabling when connected via the side openings. See the

illustrations on page 4.

1. Using the drill template, drill two holes in the ceiling/wall.

2. Route and connect all the required cables. See Connect the cables, below.

3. Fasten the camera unit to a ceiling or wall, using screws and plugs appropriate for the

ceiling/wall material.

4. Ensure the camera is positioned so that the tamper-proof screws can be tightened using

the supplied screwdriver.

Mounting on a hard ceiling

To mount the AXIS 216FD/216FD-V/216MFD/216MFD-V on a hard ceiling, check that the

ceiling material is sturdy enough to hold the weight of the camera.

The camera can also be secured using a plate or board that better carries the weight of the

camera, and which is more suitable for securing the screws.

The AXIS 216FD/AXIS 216MFD can also be mounted using the AXIS 216FD/AXIS 216MFD

Drop Ceiling Mount, which allows the camera to be mounted more discreetly. Please see

www.axis.com for all available mounting accessories.

!

IMPORTANT! - The casing of the AXIS 216FD/216FD-V/216MFD/216MFD-V

is not approved for outdoor use - the product may only be installed in indoor

environments.

Plate or

Hard ceiling

AXIS 216FD/216FD-V

Screws

board

216MFD/216MFD-V

Page 6 AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide

Connect the cables

1. Connect the camera to the network using a shielded network cable.

2. Optionally connect external input/output devices, e.g. alarm devices. See page 14 for

information on the terminal connector pins.

3. Optionally connect an active speaker and/or external microphone.

4. Connect power, using one of the methods listed below:

• PoE (Power over Ethernet). If available, this is automatically detected when the

network cable is connected (see above).

• Connect the supplied indoor power supply to the power connector on the camera.

5. Check that the indicator LED:s indicate the correct conditions. See the table on page 15

for further details. Note that some LEDs can be disabled and may be unlit.

AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide Page 7

ENGLISH

Assign an IP address

Most networks today have a DHCP server that automatically assigns IP addresses to

connected devices. If your network does not have a DHCP server the AXIS 216FD/216FD-V/

216MFD/216MFD-V will use 192.168.0.90 as the default IP address.

If you would like to assign a static IP address the recommended method in Windows is either

AXIS IP Utility or AXIS Camera Management. Depending on the number of cameras you

wish to install, use the method that best suits your purpose.

Both of these free applications are available on the Axis Network Video Product CD supplied

with this product, or they can be downloaded from www.axis.com/techsup

Notes:

• If assigning the IP address fails, check that there is no firewall blocking the operation.

• For other methods of assigning or discovering the IP address of the AXIS 216FD/216FD-V/216MFD/

216MFD-V, e.g. in other operating systems, see page 13.

Method Recommended for Operating system

AXIS IP Utility

See page 8

Single camera

Small installations

Windows

AXIS Camera Management

See page 9

Multiple cameras

Large installations

Installation on a different subnet

Windows 2000

Windows XP Pro

Windows 2003 Server

Page 8 AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide

AXIS IP Utility - single camera/small installation

AXIS IP Utility automatically discovers and displays Axis devices on your network. The

application can also be used to manually assign a static IP address.

Note that the computer running AXIS IP Utility must be on the same network segment

(physical subnet) as the AXIS 216FD/216FD-V/216MFD/216MFD-V.

Automatic discovery

1. Check that the AXIS 216FD/216FD-V/216MFD/216MFD-V is connected to the network

and that power has been applied.

2. Start AXIS IP Utility.

3. When the camera appears in the window, double-click it to open its home page.

4. See page 10 for instructions on how to assign the password.

Assign the IP address manually (optional)

1. Acquire an unused IP address on the same network segment as your computer.

2. Select the AXIS 216FD/AXIS 216MFD in the list.

3. Click the button Assign new IP address to the selected device and enter the IP

address.

4. Click the Assign button and follow the instructions.

5. Click the Home Page button to access the camera’s web pages.

6. See page 10 for instructions on how to set the password.

Note:

AXIS 216FD and AXIS 216FD-V will display in AXIS Camera Management as

AXIS 216FD. AXIS 216MFD and AXIS 216MFD-V will display in AXIS Camera

Management as AXIS 216MFD.

AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide Page 9

ENGLISH

AXIS Camera Management - multiple cameras/large installations

AXIS Camera Management can automatically discover multiple Axis devices, show

connection status, manage firmware upgrades and set IP addresses.

Automatic discovery

1. Check that the camera is connected to the network and that power has been applied.

2. Start AXIS Camera Management. When the AXIS 216FD/AXIS 216MFD appears in the

window, double-click it to open the camera’s home page.

3. See page 10 for instructions on how to set the password.

Assign an IP address in a single device

1. Select AXIS 216FD/AXIS 216MFD in AXIS Camera Man-

agement and click the Assign IP button.

2. Select Assign the following IP address and enter the IP

address, the subnet mask and default router the device

will use.

3. Click the OK button.

Assign IP addresses in multiple devices

AXIS Camera Management speeds up the process of

assigning IP addresses to multiple devices, by suggesting IP

addresses from a specified range.

1. Select the devices you wish to configure (different mod-

els can be selected) and click the Assign IP button.

2. Select Assign the following IP address range and enter

the range of IP addresses, the subnet mask and default

router the devices will use.

3. Click the OK button.

Note:

AXIS 216FD and AXIS 216FD-V will display in AXIS Camera Management as

AXIS 216FD. AXIS 216MFD and AXIS 216MFD-V will display in AXIS Camera

Management as AXIS 216MFD.

Page 10 AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide

Set the password

When accessing the AXIS 216FD/216FD-V/

216MFD/216MFD-V for the first time, the

‘Configure Root Password’ dialog will be

displayed.

1. Enter a password and then re-enter it, to con-

firm the spelling. Click OK.

2. Enter the user name root in the ‘Enter

Network Password’ dialog.

Note: The default administrator user name root cannot be deleted.

3. Enter the password as set above, and click OK. If the password is lost, the AXIS 216FD/

216FD-V/216MFD/216MFD-V must be reset to the factory default settings. See page 16.

4. If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the

video stream in Internet Explorer. You will need administrator rights on the computer to

do this.

The Live View page of the AXIS 216FD/216FD-V/216MFD/216MFD-V is displayed, with

links to the Setup tools, which allow you to customize the camera. Note that both AXIS

216FD/216FD-V will display in the browser as AXIS 216FD and AXIS 216MFD/216MFD-V

will display in the browser as the AXIS 216MFD.

Setup - Provides all the tools for configuring

the camera to requirements.

Help - Displays

online help on all

aspects of using

the camera.

AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide Page 11

ENGLISH

Adjust the image and focus

Open the Live View page in the web interface and make the following adjustments to the

camera:

1. Loosen the locking screw and

tilt adjustment screws.

2. Turn the lens to the desired

position.

3. Once satisfied, gently tighten

the locking screw and tilt

adjustment screws to secure

the camera’s position.

4. Turn the image balance ring

to set the horizontal position.

5. Open the Focus Adjustment

page in the Web interface

under Basic Configuration >

Focus and follow the on-

screen instructions. Use the

image window to adjust the

focus and zoom.

6. To set the focus and zoom,

loosen the zoom and focus pullers anti-clockwise and rotate the rings.

Note:

Due to the dome’s refraction, the image might appear slightly out of focus once

the dome has been placed. To compensate, focus on an object slightly closer than

the inteded area.

7. Lock the focus and zoom pullers in position by rotating the screws clockwise.

The image can also be fine-tuned for low lighting conditions.

Go to Setup > Video & Image > Advanced and see the online help for more information.

Complete the installation

1. Rotate the black protective shield inside the dome casing to match the camera’s position.

2. Clean the dome with a dry soft cloth to remove dust and finger prints and use a blower

to remove dust from the lens.

3. Mount the dome casing using the supplied tamper-proof screws and screw driver.

4. Now that the dome is in place, double-check that the camera is properly focused.

5. The installation is now complete.

Image

Focus puller

Zoom puller

screw

Tilt adjustment

screw

Tilt adjustment

balance

ring

Locking screw

Page 12 AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide

Accessing the camera from the Internet

Once installed, your AXIS 216FD/216FD-V/216MFD/216MFD-V is accessible on your local

network (LAN). To access the camera from the Internet, network routers must be configured

to allow incoming traffic, which is usually done on a specific port. Please refer to the

documentation for your router for further instructions. For more information on this and

other topics, visit the Axis Support Web at www.axis.com/techsup

AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide Page 13

ENGLISH

Other methods of setting the IP address

The table below shows the other methods available for setting or discovering the IP address.

All methods are enabled by default, and all can be disabled.

Set the IP address with ARP/Ping

1. Acquire an IP address on the same network segment your computer is connected to.

2. Locate the serial number (S/N) on the AXIS 216FD/216FD-V/216MFD/216MFD-V label.

3. Open a command prompt on your computer and enter the following commands:

4. Check that the network cable is connected to the camera and then start/restart the

camera, by disconnecting and reconnecting power.

5. Close the command prompt when you see ‘Reply from 192.168.0.125: ...’ or similar.

6. In your browser, type in http://<IP address> in the Location/Address field and press Enter

on your keyboard.

Notes:

• To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.

• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.

Use in operating

system

Notes

UPnP™

Windows

(ME or XP)

When enabled on your computer, the camera is automatically

detected and added to “My Network Places.”

Bonjour

MAC OSX

(10.4 or later)

Applicable to browsers with support for Bonjour. Navigate to the

Bonjour bookmark in your browser (e.g. Safari) and click on the

link to access the camera’s web pages.

AXIS Dynamic DNS

Service

All A free service from Axis that allows you to quickly and simply

install your camera. Requires an Internet connection with no

HTTP proxy. See www.axiscam.net for more information.

ARP/Ping

All See below. The command must be issued within 2 minutes of

connecting power to the camera.

View DHCP server

admin pages

All To view the admin pages for the network DHCP server, see the

server’s own documentation.

Windows syntax Windows example

arp -s <IP Address> <Serial Number>

ping -l 408 -t <IP Address>

arp -s 192.168.0.125 00-40-8c-18-10-00

ping -l 408 -t 192.168.0.125

UNIX/Linux/Mac syntax UNIX/Linux/Mac example

arp -s <IP Address> <Serial Number> temp

ping -s 408 <IP Address>

arp -s 192.168.0.125 00:40:8c:18:10:00

temp

ping -s 408 192.168.0.125

Page 14 AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide

Unit connectors

Network connector - RJ-45 Ethernet connector. Supports Power over Ethernet. Using

shielded cables is recommended.

Power connector - Mini DC connector. 5.1V DC, max 3.8W. See product label for

±

connection.

Audio in - 3.5mm input for a mono microphone, or a line-in mono signal (left channel is

used from a stereo signal).

Audio out - Audio output (line level) that can be connected to a public address (PA) system

or an active speaker with a built-in amplifier. A pair of headphones can also be attached. A

stereo connector must be used for the audio out.

I/O terminal connector - Used in applications for e.g. motion detection, event triggering,

time lapse recording and alarm notifications. It provides the interface to:

• 1 transistor output - For connecting external devices such as relays and LEDs.

Connected devices can be activated by AXIS VAPIX AP, output buttons on the

Live View page or by an Event Type. The output will show as active (shown

under Event Configuration > Port Status) if the alarm device is activated.

• 1 digital input - An alarm input for connecting devices that can toggle between

an open and closed circuit, for example: PIRs, door/window contacts, glass break

detectors, etc. When a signal is received the state changes and the input becomes

active (shown under Event Configuration > Port Status).

• Auxiliary power and GND

Function Pin number Notes Specifications

GND 1

3.3V DC

Power

2 Can be used to power auxiliary equipment.

Note: This pin can only

be used as power out.

Max load = 50mA

Digital Input 3 Connect to GND to activate, or leave floating

(or unconnected) to deactivate.

Must not be exposed to

voltages greater than

10V DC

Transistor

Output

4 Uses an open-collector NPN transistor with

the emitter connected to the GND pin. If used

with an external relay, a diode must be con-

nected in parallel with the load, for protection

against voltage transients.

Max load = 50mA

Max voltage = 24V DC

(to the transistor)

AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide Page 15

ENGLISH

Connection diagram

LED indicators

LED Color Indication

Network Green Steady for connection to a 100 Mbit/s network. Flashes for network activity.

Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.

Unlit No network connection.

Status Green Steady green for normal operation.

Note: The Status LED can be configured to be unlit during normal operation, or to

flash only when the camera is accessed. To configure, go to Setup > System

Options > LED settings. See the online help files for more information.

Amber Steady during startup, during reset to factory default or when restoring settings.

Red Slow flash for failed upgrade.

Power Green Normal operation.

Amber Flashes green/amber during firmware upgrade.

o

z

AXIS 216FD/216FD-V/216MFD/216MFD-V

3.3V

max. 50mA

e.g. pushbutton

4

o

3

o

2

1

Page 16 AXIS 216FD/216FD-V/216MFD/216MFD-V Installation Guide

Resetting to the Factory Default Settings

This will reset all parameters, including the IP address, to the Factory Default settings:

1. Disconnect power from the camera.

2. Press and hold the Control button and reconnect power.

3. Keep the Control button pressed until the Power indicator flashes amber (this may take

up to 15 seconds).

4. Release the Control button. When the Power indicator displays green (which can take up

to 1 minute) the process is complete and the camera has been reset.

5. Re-assign the IP address, using one of the methods described in this document.

It is also possible to reset parameters to the original factory default settings via the web

interface. For more information, please see the online help or the user’s manual.

Further information

The user’s manual is available from the Axis Web site at www.axis.com or from the Axis

Network Video Product CD supplied with this product.

Tip!

Visit www.axis.com/techsup to check if there is updated firmware available for your

AXIS 216FD/216FD-V/216MFD/216MFD-V. To see the currently installed firmware

version, see the Basic Configuration web page in the product’s Setup tools.

AXIS 216FD/216FD-V/216MFD/216MFD-V Guide d’installation Page 17

FRANCAIS

AXIS 216FD/216FD-V

AXIS 216MFD/216MFD-V

Guide d'installation

Ce guide d'installation vous explique comment installer la AXIS 216FD, AXIS 216FD-V,

AXIS 216MFD, et AXIS 216MFD-V sur votre réseau. Pour d'autres informations sur

l'utilisation de ce produit, consultez le Manuel de l'utilisateur, disponible sur le CD fourni, ou

visitez le site www.axis.com/techsup

Étapes de l'installation

1. Vérifiez le contenu de la livraison à l'aide de la liste ci-dessous.

2. Présentation du matériel. Reportez-vous à la page 18.

3. Installez le matériel. Reportez-vous à la page 19.

4. Paramétrez une adresse IP. Reportez-vous à la page 21.

5. Définissez le mot de passe. Reportez-vous à la page 24.

6. Réglez la mise au point. Reportez-vous à la page 25.

7. Complétez l'installation. Reportez-vous à la page 25.

Contenu de l'emballage

Article Modèles/variantes/remarques

Caméra réseau AXIS 216FD: boitier invoyable

AXIS 216FD-V: boitier a l'épreuve du vandalisme

AXIS 216MFD: boitier invoyable

AXIS 216MFD-V: boitier a l'épreuve du vandalisme

Alimentation intérieure

PS-H

(dépend du pays)

Europe

Royaume-Uni

Australie

États-Unis/Japon

Argentine

Corée

Prolongateur de câble

d’alimentation

1,8 mètres

Connecteur pour ter-

minaux

Connecteur 4 broches pour la connexion d'équipements externes au connecteur E/S

Kit de montage Tournevis pour vis inviolables

Vis inviolables

Gabarit de perçage

CD CD de la caméra vidéo réseau Axis comprenant les outils d'installation, les autres logiciels et la

documentation

Documentation AXIS 216FD/216FD-V/216MFD/216MFD-V Guide d'installation (le présent document)

Document de garantie d'Axis

Important !

Ce produit doit être utilisé

conformément aux lois et

dispositions locales en

vigueur.

Page 18 AXIS 216FD/216FD-V/216MFD/216MFD-V Guide d’installation

Présentation du matériel

D

imensions

H x L x P = 94 x 144 x 132mm

Poids AXIS 216FD/AXIS 216MFD = 425g (alimentation exclue)

Poids AXIS 216FD-V/216MFD-V = 580g (alimentation exclue)

Connecteur de

réseau

(reportez-vous à la

page 28)

Connecteur

d'alimentation

(reportez-vous

à la page 28)

Témoin DEL d’état

ID du produit et numéro de

série (S/N). Le numéro de

série peut être requis

pendant l'installation.

Témoin

DEL réseau

Bouton de

commande

Témoin DEL

d’alimentation

Capot plaques

Conduit de 16mm (non

fourni) adaptable à

AXIS

216FD-V/216MFD-V

Connecteur pour terminaux E/S

(reportez-vous à la page 28)

Entrée

audio

Sortie

audio

Microphone

AXIS 216FD/216FD-V/216MFD/216MFD-V Guide d’installation Page 19

FRANCAIS

Installation du matériel

Montage de la caméra

La caméra AXIS 216FD/216FD-V/216MFD/216MFD-V peut être montée avec les câbles

d'alimentation et réseau acheminés dans le mur/plafond, ou depuis le haut ou le bas. Vous

disposez de plaques d'obturation pour les ouvertures des deux côtés du capot du dôme.

L’AXIS 216FD-V/216MFD-V peut aussi equipé avec un conduit en métal afin de protéger le

câblage lorsqu'il est connecté par les ouvertures latérales. Consultez les figures de la page 18.

1. Avec le gabarit de perçage, percez deux trous dans le plafond/mur.

2. Orienter et connecter tous les câbles néccessaires. Voi Branchement des câbles, en bas.

3. Fixez la caméra au plafond ou au mur à l'aide des vis et des chevilles appropriées.

4. Veillez à ce que la caméra soit positionnée de telle manière que les vis inviolables

puissent être serrées à l'aide du tournevis fourni.

Montage au plafond dur

Pour monter l’AXIS 216FD/216FD-V/216MFD/216MFD-V au plafond dur, vérifier si le

materiau du plafond est assez solid pour soutenir le poids de la caméra.

Pour fixer la caméra, vous pouvez utiliser une plaque ou une carte supportant le poids de la

caméra, qui sera plus adaptée à la fixation des vis.

The AXIS 216FD/AXIS 216MFD peut aussi être montée à l'aide de l’AXIS 216FD/AXIS

216MFD Drop Ceiling Mount, qui permet de placer la caméra plus discrètement. Voir

www.axis.com pour les accessoires de montage disponibles.

!

IMPORTANT! - Le boitier de l'AXIS 216FD/216FD-V/216MFD/216MFD-V

n'est pas approuvé pour une utilisation extérieure - Le produit doit être

uniquement installé en intérieur.

Plaque ou

plafond dur

AXIS 216FD/216FD-V

Vis

carte

216MFD/216MFD-V

Page 20 AXIS 216FD/216FD-V/216MFD/216MFD-V Guide d’installation

Branchement des câbles

1. Connectez la caméra à votre réseau à l'aide d'un câble de réseau blindé.

2. Si vous le souhaitez, connectez des dispositifs externes, par exemple des dispositifs d'alarme.

Reportez-vous à la page 28 pour plus d'informations sur les broches du connecteur pour

terminaux.

3. Si vous le souhaitez, connectez un haut-parleur actif pour la transmission audio

bidirectionnelle.

4. Branchez l'alimentation à l'aide de l'une des méthodes reprises ci-dessous.

• PoE (Alimentation éléctrique par câble ethernet). Si disponible, ceci est automa-

tiquement détecté quand le câble résau est connecté (Voir au -dessus).

• Branchez l'alimentation intérieure fournie au connecteur d'alimentation de la caméra.

5. Vérifiez que les témoins DEL indiquent les conditions correctes. Pour plus d'informations,

consultez le tableau à la page 29. Notez que certains témoins DEL peuvent être désactivés et

éteints.

La page charge ...

Axis Communications 18613 Manuel utilisateur

Ce manuel convient également à

Axis Communications 18613 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents