Bradford White UDH1-65T6FRN Guide d'installation

238-48114-00B REV 11/14

INSTALLATION INSTRUCTIONS FOR

SOLID VENT KIT PART NUMBER

239-47810-00

239-51283-00

This vent kit is designed to bring all air for combustion from the outside and

vent all the combustion products to the outside when properly installed. This

vent kit should only be used with direct vent water heaters that were

designed to use this vent kit. Refer to the label on the water heater to

determine if this kit is the correct kit for the water heater that you are

installing. Consult the supplier of the water heater if you are not certain that

this is the correct vent kit. Refer to the information in these instructions and

the instructions provided with the water heater when determining the location

of the vent terminal and water heater.

The vent system must terminate so that proper clearances are maintained as

cited in local codes or the latest edition of the National Fuel Gas Code, ANSI

Z223.1 as follows:

1. Do not terminate near soffit vents or crawl space or other area where

condensate or vapor could create a nuisance or hazard or cause

property damage.

2. Do not terminate the exhaust vent terminal where condensate or vapor

could cause damage or could be detrimental to the operation of

regulators, relief valves, or other equipment.

3. Do not terminate the exhaust vent terminal over public area or

walkways where condensate or vapor can cause nuisance or hazard.

4. The vent shall terminate a minimum of 12 inches above expected

snowfall level to prevent blockage of vent termination.

Vent pipes serving direct vent appliances are classified by building codes as

“vent connectors”. Required clearances from combustible materials must be

provided in accordance with information in this manual under LOCATION OF

WATER HEATER and CLEARANCES, and with National Fuel Gas Code

and local code.

WARNING

The vent-air intake system must be properly installed. Failure to

properly install the vent-air intake system could result in property

damage, personal injury or death.

DO NOT install any damaged vent-air intake system components.

Contact the manufacturer of the water heater for replacement parts.

2

Figure 1

Direct Vent Terminal Clearances

Canadian Installations

1

US Installations

2

A= Clearance above grade, veranda, porch, deck or balcony 12 inches (30 m) 12 inches (30 cm)

B= Clearance to widow or door that may be opened 12 inches (30 m) 9 inches (23 cm)

C= Clearance to permanently closed widow *b *b

D=

Vertical clearance to ventilated soffit located above the

terminal within a horizontal distance of 2 feet (61 cm) from

the center line of the terminal

12 inches (30 cm) *a

12 inches (30 cm)

*a

E= Clearance to unventilated soffit 12 inches (30 cm) *a 12 inches (30 cm) *a

F= Clearance to outside corner *b *b

G= Clearance to inside corner *b *b

H=

Clearance to each side of center line extended above

meter/regulator assembly

3 feet (91 cm) within a

height 15 feet (4.6 m)

above the meter/regulator

assembly

*b

I= Clearance to service regulator vent outlet or oil tank vent 36 inches (91 cm) *b

J=

Clearance to non-mechanical air supply inlet to building or

the combustion air inlet to any other appliance

12 inches (30 cm) 9 inches (23 cm)

K= Clearance to a mechanical air supply inlet 6 feet (1.83 m)

3 feet (91 cm) above

if within 10 feet

horizontally

L=

Clearance above paved sidewalk or paved driveway

located on public property

7 feet (2.13 m)† *b

M= Clearance under a veranda, porch, deck, or balcony 12 inches (30 cm) ‡ *b

1

In accordance with the current CAN/CGA-B149 Installation Codes.

2

In accordance with the current ANSI Z223.1-(Latest edition)/NFPA 54 National Fuel Gas Code.

† A vent shall not terminate directly above a sidewalk or paved driveway that is located between two

single-family dwellings and serves both dwellings.

‡ Permitted only if a veranda, porch, deck or balcony is fully open on a minimum of two sides beneath

the floor.

*a) A minimum clearance value determined by testing in accordance with section 2.20.

*b) “Clearance in accordance with local installation codes and the requirements of the gas supplier”.

3

IMPORTANT – Refer to parts list in the back of this manual

and become familiar with the parts named in kit.

The co-axial vent-air intake tubes of this water heater can be installed in any

360 configuration as long as the proper clearances for installation,

plumbing, operation and servicing are maintained. (See Figure 2).

Figure 2

Note: Maintain proper clearances for installation, plumbing, operation

and service.

SOLID VENT KIT INSTALLATION

WARNING

The vent-air intake system must be properly installed. Failure to

properly install the vent-air intake system could result in property

damage, personal injury or death.

DO NOT install any damaged vent-air intake system components.

Contact the manufacturer of the water heater for replacement parts.

WARNING

The vent-air intake terminal must be installed through an outside wall in a

horizontal position. This direct vent water heater is not designed for through the

roof vertical venting.

4

HORIZONTAL AND VERTICAL VENT-AIR INTAKE LENGTHS

This Direct Vent Gas Water Heater may come with one (1) solid vent-air

intake “Kit C”. Optional vent-air intake kits are available that can extend the

horizontal length and/or vertical height of the vent-air intake system. Table A

lists the various vertical and horizontal vent-air intake system configurations.

The water heater may be shipped with a solid vent and air intake kit. The

components of this vent and air intake systems may be as follows:

3” Vent Tube* Vent Terminal Hardware

5” Air Intake Tube* RTV Silicone Sealant

Vent Terminal 3” Vent Elbow

Inner Wall Term. Mounting Flange 5” Vent Elbow

Outer Wall Term. Mounting Flange

*The vent and air intake telescopes from 13 3/4" to 23 11/16”.

Table A

Horizontal "X"

13 1/4

14 3/16

15

17 11/16

22 1/4

32 3/16

36

55 7/8

58 5/16

104 5/16

Vertical "Y"

10

order

kit A

order

kit B

no add'l

kit req'd

order

kit C

order

kit D

14 3/4

15 11/16

*order

kit A (2)

order

kit A & B

order

kit A

order

kit A & C

order

kit A & D

16 1/2

19 3/16

order

kit A & B

*order

kit B (2)

order

kit B

order

kit B & C

order

kit B & D

23 3/4

33 11/16

order

kit A

order

kit B

order

kit C

*order

kit C (2)

order

kit D

37 1/2

57 3/8

order

kit A & C

order

kit C & B

*order

kit C (2)

*order

kit C (3)

order

kit C & D

59 13/16

105 13/16

order

kit D & A

order

kit D & B

order

kit D

order

kit D & C

*order

kit D (2)

* (2) = Order two of the kits referenced.

* (3) = Order three of the kits referenced.

The bold text above show what kit(s) are needed in addition to the standard

vent and air intake tubes. If the standard vent and air intake tubes are not

used in the venting system (those that do not have bold text) they can be

discarded or saved.

5

Figure 3

6

VENT-AIR INTAKE SYSTEM INSTALLATION

Tools Required For Vent-Air Intake Installation

The following minimum tools are required to properly install the vent-

air intake system. Note: Wall construction will determine tool usage.

 Tape Measure

 Drill

 3/16 inch (4.5 mm) Diameter Drill Bit(s)

 1/8 inch (3.0 mm) Diameter Drill Bit(s)

 Masonry Drill Bit(s) (For Poured Concrete, Concrete Block and Brick

Wall Construction)

 Reciprocating Saw w/appropriate Blade(s) (Dependent on Wall

Construction)

 Chisel (For Poured Concrete, Concrete Block and Brick Wall

Construction)

 Hammer (For Poured Concrete, Concrete Block and Brick Wall

Construction)

 1/4 & 5/16 inch Nut Drivers (Preferred) or Slotted Head Screwdriver

 Phillips Head Screwdriver

WARNING

The vent-air intake system must be properly installed. Failure to

properly install the vent-air intake system could result in property

damage, personal injury or death.

Do not install any damaged vent-air intake system components.

Contact the manufacturer of the water heater for replacement parts.

IMPORTANT

When the following instructions specify, to seal a vent-air intake

joint, use only Loctite Ultra Blue 587 RTV Silicone sealant. A

tube of Loctite Ultra Blue 587 RTV Silicone sealant is supplied

with every direct vent water heater and each optional vent-air

intake kit. Make sure that all joints are completely sealed.

When drilling pilot holes for the #8 sheet metal screws through

the five (5) inch (12.7 cm) diameter components, be careful not

to drill into the inner three (3) inch (7.6 cm) diameter

components.

7

1. Measure the vertical height “Y” required in your installation (See Figure

3). Reference the appropriate Table A to determine number of vent-air

intake kits required in your installation.

2. Measure the horizontal length “X” required in your installation (See

Figure 3). Reference Table A to determine number of vent-air intake kits

required in your installation.

3. Cut a 5-1/2 inch (14 cm) diameter minimum clearance hole in the wall at

the point where the vent-air intake tubes will pass through the outside

wall and connect with the direct vent-air intake terminal (See Figure 4).

4. From outside the building, position the outer wall mount plate and direct

vent-air intake terminal over the center of the opening. Mark the

mounting screw hole locations. With a 3/16 inch (4.5 mm) diameter drill

bit (not supplied), drill holes for the wall anchors (supplied). Install the

wall anchors but DO NOT affix the outer wall mount plate and direct

vent-air intake terminal to the wall at this time (See Figure 4). Note:

Certain construction of walls may require the use of a different type of

wall anchoring means than supplied. DO NOT modify the direct vent-air

intake terminal or outer wall mount plate.

Figure 4

8

5. Insert the straight end of the three (3) inch (7.6 cm) diameter

elbow into the flue reducer until firmly seated and oriented in the

correct direction. With a 1/8 inch (3.0 mm) diameter drill bit (not

supplied), drill three (3) holes, 120

o

apart, through the flue

reducer into the three (3) inch (7.6 cm) diameter elbow. Fasten

with three (3) #8 sheet metal screws (supplied). Using the

supplied special RTV silicone sealant, apply a sufficient amount

to seal the joint (See Figure 5).

Figure 5

6. Place the straight end of the five (5) inch (12.7 cm) diameter

elbow over the three (3) inch (7.6 cm) diameter elbow and

plenum collar until seated on top of the plenum box. Make

certain that the five (5) inch (12.7 cm) diameter elbow is oriented

in the same direction as the three (3) inch (7.6 cm) diameter

elbow and both are oriented in the correct direction. Drill three

(3) 1/8 inch (3.0 mm) diameter holes, 120

o

apart, through the five

(5) inch (12.7 cm) diameter elbow into the plenum collar. Fasten

with three (3) #8 sheet metal screws (supplied) (See Figure 6).

9

Figure 6

7. Extend the three (3) inch (7.6 cm) diameter telescopic tube to its

maximum length and slide the backing plate over it. Place the

large end of the three (3) inch (7.6 cm) diameter telescopic tube

through the hole in the outside wall. Insert the smaller end of the

three (3) inch diameter (7.6 cm) telescopic tube into the flared

end of the three (3) inch (7.6 cm) diameter elbow, one (1) inch

(2.5 cm) (or until seated). Drill three (3) 1/8 inch diameter holes,

120

o

apart, through the three (3) inch (7.6 cm) diameter elbow

into the three (3) inch (7.6 cm) diameter telescopic tube. Fasten

with three (3) #8 sheet metal screws (supplied). Adjust the

overall length of the three (3) inch (7.6 cm) diameter telescopic

tube so that 2-1/2 inches (6.4 cm) extends beyond the outside

wall. Drill three (3) 1/8 inch (3.0 mm) diameter holes, 120

o

apart,

through the three (3) inch (7.6 cm) diameter telescopic tubes

where the small and large sections overlap. Fasten with three (3)

#8 sheet metal screws (supplied). Using the supplied special

RTV silicone sealant, apply a sufficient amount to seal the joints

(See Figure 7).

10

Figure 7

8. Extend the five (5) inch (12.7 cm) diameter telescopic tube to its

maximum length. Place the large end of the five (5) inch (12.7

cm) diameter telescopic tube over the collar on the outer wall

mount plate. Drill three (3) 1/8 inch (3.0 mm) diameter holes,

120

o

apart, through the five (5) inch (12.7 cm) diameter telescopic

tube into the collar on the outer wall mount plate. Fasten with

three

(3) #8 sheet metal screws (supplied). Using the supplied

special RTV silicone sealant, apply a sufficient amount to seal the

joint (See Figure 8).

Figure 8

11

9. From outside the building, slide the five (5) inch (12.7 cm)

diameter telescopic tube through the opening in the wall until the

outer wall mount plate is flush with the wall (See Figure 9).

Figure 9

10. Using the supplied special RTV silicone sealant, apply a bead

one (1) inch (2.5 cm) from the end of the three (3) inch (7.6 cm)

diameter tube that is part of the vent-air intake terminal. Slide the

direct vent-air intake terminal into the three (3) inch (7.6 cm)

diameter telescopic tube that extends through the wall and

position it so it is flush with the outer wall mount plate. Make sure

that the rain guard and the word “HOT” on the end of the direct

vent-air intake terminal are oriented properly. Secure the direct

vent-air intake terminal to the outer wall mount plate and wall with

four (4) #10 x 1 inch screws (supplied) (See Figure 10). Note:

Certain construction of walls may require the use of different type

of anchoring means than supplied. DO NOT modify the direct

vent-air intake terminal or outer wall mount plate.

12

Figure 10

11. From inside the building, slide the backing plate over the five (5)

inch (12.7 cm) diameter telescopic tube until it is flush with the

wall. Adjust the length of the five (5) inch (12.7 cm) diameter

telescopic tube and insert the end into the flared end of the five

(5) inch (12.7 cm) diameter elbow one (1) inch (2.5 cm) (or until

seated). Drill three (3) 1/8 inch (3.0 mm) diameter holes, 120

o

apart, through the five (5) inch (12.7 cm) diameter elbow into the

five (5) inch (12.7 cm) diameter telescopic tube and through the

tubes where the small and large sections overlap. Fasten with

three (3) #8 sheet metal screws (supplied). Using the supplied

special RTV silicone sealant, apply a sufficient amount to seal all

joints (See Figure 11).

Figure 11

13

12. Mark the mounting screw hole locations for the backing plate.

Rotate the backing plate in order to gain access to the markings.

With a 3/16 inch diameter drill bit (not supplied), drill holes for the

supplied wall anchors. Install the wall anchors and secure the

backing plate to the wall with four (4) #10 x 1 inch screws

(supplied) (See Figure 12). Note: Certain construction of walls

may require the use of a different type of anchoring means than

supplied.

Figure 12

IMPORTANT

When the installation is complete, visually inspect the air intake

system to insure that all joints are completely sealed.

14

DIRECT VENT WATER HEATER VENTING PARTS LISTS

PART NAME & DESCRIPTION

1. Direct Vent-Air Intake Terminal 6. Inner Telescopic Vent Tube

2. Outer Wall Mounting Plate 7. Inner Elbow

3. Inner Wall Backing Plate 8. Vent Terminal Guard (Optional

not included)

4. Outer Telescopic Air Intake Tube 9. Special RTV silicone sealant

5. Outer Elbow

15

VENT-AIR INTAKE KITS

16

NOTES:

16

NOTES:

15

VENT-AIR INTAKE KITS

14

LISTES DES PIÈCES DIRECTES DE MISE À L'AIR LIBRE

DE CHAUFFE-EAU DE PASSAGE

NOM ET DESCRIPTION DE PARTIE

1.

Borne directe de prise de

Passage-Air

6.

Tube télescopique intérieur de

passage

2. Plat de support externe de mur 7. Coude intérieur

3. Plat intérieur de support de mur 8.

Garde terminale de passage

(non inclus facultatifs)

4.

Tube externe d'entrée d'air de

télescope

9.

Mastic spécial de silicone de

RTV

5. Coude externe

13

12. De l'intérieur du bâtiment, glissez le plat de support au-dessus (5) du

tube télescopique de diamètre de pouce cinq (12.7 cm) jusqu'à ce

qu'il soit affleurant du mur. Ajustez la longueur (5) du tube

télescopique de diamètre de pouce cinq (12.7 cm) et insérez

l'extrémité dans la fin évasée de cinq (5) pouces du coude un de

diamètre de pouce (12.7 cm) (1) (2.5 cm) (ou jusqu'à assis). Forez

trois (3) trous de diamètre de 1/8 pouce (3.0 mm), 120o à part, par

(5) le coude de diamètre de pouce cinq (12.7 cm) dans (5) le tube

télescopique de diamètre de pouce cinq (12.7 cm) et par les tubes

où les petites et grandes sections recouvrent. Attachez avec trois

(3) vis en métal de feuille #8 (fournies). En utilisant le mastic spécial

fourni de silicone de RTV, appliquez une quantité suffisante pour

sceller tous les joints (voir Le schéma 12).

Le schéma 12

IMPORTANT

Quand l'installation est complète, inspectez visuellement le

système d'entrée d'air pour assurer que tous les joints sont

complètement scellés.

La page charge ...

Bradford White UDH1-65T6FRN Guide d'installation

Bradford White UDH1-65T6FRN Guide d'installation

dans d''autres langues

Documents connexes

Autres documents