NAPOLEON GD82NT-TESB Manuel utilisateur

FRENCH

PG. 59

W415-2357 / 12.19.19

ADD MANUAL TITLE

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleon.com • [email protected]

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

NATURAL GAS MODELS:

PROPANE GAS MODELS:

Product Name / Code

(MUST use title from Price Book)

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

CSA /

INTERTEK

LOGO

SAFETY INFORMATION

- Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity of

this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the ﬁ re department.

- Installation and service must be

performed by a qualiﬁ ed installer, service

agency, or the supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certiﬁ ed kit is used.

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

WARNING

!

ENGLISH

$10.00

FOR INDOOR USE ONLY

IF INSTALLATION + OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

INSTALLATION AND

OPERATION MANUAL

GD82NT-TE

GD82PT-TE

GD82NT-TE

(GD82NT-TE illustrated)

SAFETY BARRIER

• This appliance is hot when operated and

can cause severe burns if contacted.

• Any changes or alterations to this

appliance or its controls can be

dangerous and is prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure

to operate appliance according to operating

instructions could cause ﬁ re or injury.

• Ensure the glass door is opened or removed

when lighting the pilot for the ﬁ rst time and

when the gas supply has run out.

• Risk of ﬁ re or asphyxiation, do not operate

appliance with ﬁ xed glass removed and never

obstruct the front opening of the appliance.

• Do not connect 110 volts to the control valve,

with the exception of models; GSST8 and

GT8.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during

installation. Sheet metal edges may be sharp.

• Do not burn wood or other materials in this appliance.

• Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing

and operating the appliance.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at

test pressures above 1/2 psig. Close the manual shut-off valve before pressure testing gas line at test

pressures equal to or less than 1/2 psig (35mb).

• The appliance must not be operated at temperatures below freezing (32°F / 0°C). Allow the appliance

to warm to above freezing prior to operation, with the exception of models; GSS36, GSS42; these

appliances are suitable for 0°F / -18°C.

• Children and adults should be alerted to hazards of high surface temperature and should stay

away to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the

appliance. Toddlers, young children and others may be susceptible to accidental contact

burns. A physical barrier is recommended if there are at risk individuals in the house. To

restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers,

young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from

furniture and draperies.

• Furniture or other objects must be kept a minimum of 4 feet (1.22m) away from the front of the appliance.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is off, it will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior

to operating the appliance.

• It is imperative that the control compartments, burners and circulating blower and its passageway in the

appliance and venting system are kept clean. The appliance and its venting system should be inspected

before use and at least annually by a qualiﬁ ed service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and

free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it

serviced. Keep burner and control compartment clean.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not allow wind or fans to blow directly into the appliance. Avoid any drafts that alter burner ﬂ ame

patterns.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

DANGER

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this appliance and

shall be installed for the protection of children and other

at-risk individuals.

!

WARNING

W415-2357 / 12.19.19

EN

2

safety information

!

WARNING

• Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this

appliance.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has

been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass

should be done by a licensed or qualiﬁ ed service person, if equipped.

• Do not strike or slam shut the appliance glass door, if equipped.

• Only doors / optional fronts certiﬁ ed with the appliance are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Carbon or soot should not occur in a vent free appliance as it can distribute into the living area of your

home. If you notice any signs of carbon or soot, immediately turn off your appliance and arrange to have

it serviced by a qualiﬁ ed technician before operating it again.

• If equipped, the screen must be in place (closed) when the appliance is in operation.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating

to prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of

the exhaust escaping through these openings can also cause the surrounding combustible materials to

overheat and catch ﬁ re.

• Carbon monoxide poisoning may lead to death; early signs of carbon monoxide poisoning resemble the

ﬂ u, with headache, dizziness and/or nausea. If you have these signs, the appliance may not be working

properly. Get fresh air at once! Have appliance serviced. Some people; pregnant women, persons with

heart or lung disease, anemia, those under the inﬂ uence of alcohol, those at high altitudes are more

affected by carbon monoxide than others. Failure to keep the primary air opening(s) of the burner(s) clean

may result in sooting and property damage.

• As with any combustion appliance, we recommend having your appliance regularly inspected and

serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and

your family against Carbon Monoxide (not applicable for outdoor appliances).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a TV or other electronic components.

• For appliances equipped with a safety barrier; if the barrier becomes damaged, the barrier

shall be replaced with the manufacturer’s barrier for this appliance.

• Installation and repair should be done by a qualiﬁ ed service person. It is imperative that control

compartments, burners and circulating air passageways of the appliance be kept clean.

• For outdoor products only: this appliance must not be installed indoors or within any structure that

prevents or inhibits the exhaust gases from dissipating in the outside atmosphere.

• If applicable, the millivolt version of this appliance uses and requires a fast acting thermocouple. Replace

only with a fast acting thermocouple supplied by Wolf Steel Ltd.

!

WARNING

!

Disconnect the appliance main gas valve/control

from the supply piping when pressure testing that

system at pressures in excess of 1/2 psi (3.5 kPa).

Isolate the appliance with it’s shut off valve during

any pressure testing of the supply piping at

pressures equal to or less than 1/2 psi (3.5 kPa).

FIRE RISK HAZARD / DELAYED IGNITION

High supply pressure will damage the valve / controls.

Add California Prop 65 warning

!

WARNING:

This product can expose you to chemicals including lead and lead compounds,

which are known to the State of California to cause cancer, and chemicals including carbon

monoxide, which are known to the State of California to cause birth defects or other reproduc-

tive harm. For more information, go to www.P65Warnings.ca.gov.

EN

W415-2357 / 12.19.19

3

safety information

1.0 general information 5

1.1 rates and efﬁ ciencies 5

1.2 rating plate information 7

1.3 mobile home installation 7

1.4 dimensions 8

2.0 venting 9

2.1 typical vent installation 10

2.2 special vent installations 11

2.2.1 periscope termination 11

2.3 minimum air terminal location

clearances 12

2.4 venting application ﬂ ow chart 13

2.5 deﬁ nitions 13

2.6 elbow vent length values 13

2.7 horizontal termination 14

2.8 vertical termination 16

3.0 installation 18

3.1 horizontal installation 19

3.2 vertical installation 19

3.3 using ﬂ exible venting components 20

3.4 horizontal air terminal installation 20

3.5 vertical air terminal installation 21

3.6 appliance vent connection 22

3.7 horizontal air terminal installation 22

3.8 extended horizontal air terminal

installation 22

3.9 vertical air terminal installation 23

3.10 gas installation 24

4.0 framing 25

4.1 minimum clearance to combustibles 27

4.2 minimum clearance to combustible

enclosures 28

4.3 alcove framing 30

4.4 minimum mantel clearances 31

5.0 finishing 32

5.1 safety screen removal / installation 32

5.2 door removal / installation 33

5.3 shipping bracket 34

5.4 bowl, mesh, and rock placement 34

5.5 AFK82/RFK82 facing kit installation 35

6.0 electrical information 36

6.1 electrical connection 36

6.1.1 hard wiring connection 36

6.1.2 schematic 36

7.0 operation 37

7.1 general transmitter layout 37

7.2 appliance operation 37

7.3 hand held remote operations 38

7.4 temperature display 38

7.5 ﬂ ame height 38

7.6 fan speed 38

7.7 child proof function 39

7.8 remote auxiliary outlet 39

7.9 low battery / manual bypass 39

7.10 in the event of a power failure 39

7.11 fan control module 39

7.12 timed blower 39

8.0 operating instructions 40

8.1 pilot-on-demand 41

9.0 adjustments 42

9.1 restricting vertical vents 42

9.2 pilot burner adjustment 42

9.3 venturi adjustment 43

9.4 ﬂ ame characteristics 43

10.0 maintenance 44

10.1 bowl and burner removal 44

10.2 decorative panel / base removal 45

10.3 blower replacement 45

10.4 night light™ replacement 46

10.5 glass / door replacement 46

10.6 care of glass 47

10.7 care of plate parts 47

11.0 replacement parts 48

11.1 overview 49

11.2 night light assembly 50

11.3 valve train assembly 51

12.0 accessories 52

13.0 troubleshooting guide 53

14.0 warranty 56

15.0 notes 57

note:

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves

the right to change or modify any information within this manual at any time without notice. Changes, other than

editorial, are denoted by a vertical line in the margin.

W415-2357 / 12.19.19

EN

4

table of contents

1.0 general information

1.1 rates and efﬁ ciencies

EN

W415-2357 / 12.19.19

5

standard checklist

When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of speciﬁ c recommenda-

tions from the local authority having jurisdiction, the certiﬁ ed high altitude input rating shall be reduced at the rate

of 4% for each additional 1,000ft (305m).

This appliance is certiﬁ ed to be installed in an aftermarket permanently located, manufactured (mobile) home,

where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certiﬁ ed kit is used. External electricity (110 volts or 24 volts) is re-

quired for the gas system operation.

Expansion / contraction noises during heating up and cooling down cycles are normal and are to be expected.

Change in ﬂ ame appearance from “HI” to “LO” is more evident in natural gas than in propane.

The protective wrap on plated parts is best removed when the assembly is at room temperature

but this can be improved if the assembly is warmed, using a hair dryer or similar heat source.

This appliance is a decorative product. It is not a source of heat and not intended to burn solid fuel.

note:

A barrier designed to reduce the risk of burns is provided with the appliance and must be installed. Never

operate the appliance without the barrier installed.

Batteries must be disposed of according to the local laws and regulations. Some batteries may be

recycled, and may be accepted for disposal at your local recycling center. Check with your

municipality for recycling instructions.

APPLIANCE

NG P

Altitude (FT) 0 - 4,500

Max. Input (BTU/HR) 26,000

Max. Output Steady State (BTU/HR) 16,000

Min. Inlet Gas Supply Pressure 4.5” Water Column (11mb) 11” Water Column (27mb)

Max. Inlet Gas Supply Pressure 7” Water Column (17mb) 13” Water Column (34mb)

Manifold Pressure (Under Flow Conditions) 3.5” Water Column (9mb) 10” Water Column (25mb)

Installer, please ﬁ ll out the following information:

Customer: _____________________________________________________________________

Address: _____________________________________________________________________

Date of Installation: _____________________________________________________________________

Location of Appliance: _____________________________________________________________________

Installer: _____________________________________________________________________

Dealer/Distributon

Contact Number: _____________________________________________________________________

Serial #: _____________________________________________________________________

Model:

Natural Gas: Propane:

GD82NT-TE GD82PT-TE

!

WARNING

• Always light the pilot, whether for the ﬁ rst time or if the gas supply has run out, with the glass door opened or

removed.

• Provide adequate clearance for servicing and operating the appliance.

• Provide adequate ventilation.

• Never obstruct the front opening of the appliance.

• Objects placed in front of the appliance must be kept a minimum of 48” (1219mm) from the front face of the

appliance.

• Surfaces around and especially above the appliance can become hot. Avoid contact when the appliance is

operating.

• Fire risk. Explosion hazard.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at test

pressures above 1/2PSIG. Close the manual shut-off valve before pressure testing gas line at test pressures

equal to or less than 1/2PSIG (35mb).

• Use only Wolf Steel approved optional accessories and replacement parts with this appliance. Using non-listed

accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could result in a safety

hazard and will void the warranty and certiﬁ cation.

THIS GAS APPLIANCE MUST BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local

codes. Installation practices vary from region to region and it is important to know the speciﬁ cs that apply to your area, for

example in the state of Massachusetts:

• This product must be installed by a licensed plumber or gas ﬁ tter when installed within the commonwealth of

Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas

log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂ exible connector must not be longer than 36 inches (0.9m).

• A carbon monoxide detector is required in all rooms containing gas ﬁ red appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed

combustion product.

The installation must conform with local codes or, in absence of local

codes, the National Gas and Propane Installation Code CSA B149.1

in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54

in the United States. Suitable for mobile home installation if installed

in accordance with the current standard CAN/CSA Z240MH Series,

for gas equipped mobile homes, in Canada or ANSI Z223.1 and

NFPA 54 in the United States.

The appliance and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing

of that system at test pressures in excess of 1/2 psig (35 mb).

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any

pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (35 mb). When installed

with a blower or fan, the junction box must be electrically connected and grounded in accordance with local codes. In the

absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI / NFPA 70 National

Electric Code in the United States. In the case where the blower is equipped with a power cord, it must be connected into a

properly grounded receptacle. The grounding prong must not be removed from the cord plug.

The following does not apply to inserts; as long as the required clearance to combustibles is maintained, the most desirable

and beneﬁ cial location for an appliance is in the center of a building, thereby allowing the most efﬁ cient use of the heat

created. The location of windows, doors and, the trafﬁ c ﬂ ow in the room where the appliance is to be located should be

considered. If possible, you should choose a location where the vent will pass through the house without cutting a ﬂ oor or

roof joist. If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ ooring, the

appliance shall be installed on a metal or wood panel extending the full width and depth, unless otherwise tested.

We suggest that our gas

hearth products be installed

and serviced by professionals

who are certied in the U.S.

by the National Fireplace

Institute

®

(NFI) as NFI Gas

Specialists

www.ncertied.org

W415-2357 / 12.19.19

EN

6

general information

1.2 rating plate information

Certiﬁed to Canadian and American National Standards: CSA 2.22-XXXX / ANSI Z21.50-XXXX for Vented Decorative Gas Appliances

Certiﬁé selon les normes Nationales Canadiennes et Américaines: CSA 2.22-XXXX / ANSI Z21.50-XXXX pour les Appareils à gaz décoratif à évacuation

Direct vent, vented gas ﬁreplaces. Approved for bedroom, bathroom and bed-sitting room installation. Suitable for mobile home installation, if installed in accordance with the current

standard CAN / CSA Z240MH Series gas equipped mobile homes in Canada, or, in the United States, the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part

3280. When this US Standard is not applicable, use the Standard for Fire Safety Criteria for Manufactured Home Installations, Sites and Communities, ANSI / NFPA 501A. This appliance

must be installed in accordance with local codes, if any; if none, follow the current ANSI Z223.1 or CSA B149. For use with barrier WXXX-XXXX. Follow installation instructions.

Foyer à gaz ventilé. Homologué pour installation dans une chambre à coucher, une salle de bain et un studio. Approprié pour installation dans une maison mobile si son installation

conforme aux exigences de la norme CAN / CSA Z240MH Séries de maisons mobile équipées au gaz en vigueur au Canada, ou, aux États-Unis selon la norme 24 CFR, Part 3280,

Manufactured Home Construction and Safety Standard. Dans le cas ou cette norme d’États-Unis n’est pas pertinentes, utiliser la norme NFPA 501A, Fire Safety Criteria for Manufactured

Home Installations, Sites and Communities. Installer l’appareil selon les codes ou règlements locaux ou, en l’absence de tels règlements, selon les codes d’installation ANSI Z223.1 ou

CSA B149 en vigueur. Utiliser uniquement avec l’écran WXXX-XXXX. Suivre les instructions d’installation.

9700539 (WSL) 4001658 (NAC) 4001657 (NGZ) 4001659 (WUSA)

WOLF STEEL LTD. 24 Napoleon Road, Barrie, ON, L4M 0G8 Canada

XXXX XXXX XXXX XXXX

MODEL / MODÈLE

Altitude

Input

Reduced Input

P4

Élévation

Alimentation

Alimentation Réduite

P4

Manifold Pressure: 3.5” w.c. (NG)

Minimum Supply Pressure: 4.5” w.c. (NG)

Maximum Supply Pressure: 7”* w.c. (NG)

Pression au Collecteur: 3,5” d’une colonne d’eau (GN)

Pression d’Alimentation Min.: 4,5” d’une colonne d’eau (GN)

Pression d’Alimentation Max.: 7” ** d’une colonne d’eau (GN)

** Maximum inlet pressure not to exceed 13”.

Manifold Pressure: 10” w.c. (P)

Minimum Supply Pressure: 11” w.c. (P)

Maximum Supply Pressure: 13”* w.c. (P)

Pression au Collecteur: 10” d’une colonne d’eau (P)

Pression d’Alimentation Min.: 11” d’une colonne d’eau (P)

Pression d’Alimentation Max.: 13” * d’une colonne d’eau (P)

** Pression d’alimentation maximale ne devait pas dépasser 13”.

0-XXXXft (0-XXXXm)

Minimum clearance to combustible materials:

Top, sides & back: per standoff spacers for framing and ﬁnishing

materials. For non-combustible framing and ﬁnishing materials,

see installation manual.

Top X”

Floor X”

Sides X”

Back X”

Vent top X”

Vent sides & bottom X”

Recessed depth X”

*** Mantel X” from appliance opening

Dégagements minimaux des matériaux combustibles:

Dessus, côtés et arrière: selon les espaceurs de dégagements

pour les matériaux d’ossature selon le manuel du propriétaire

pour les matériaux de ﬁnition.

Dessus X”

Plancher X“

Côtés X”

Arrière X“

Dessus du conduit d’évent X”

Côtés et dessous du conduit d’évent X”

Profondeur d’encastré une face X”

*** Tablette X” de l’ouverture de l’appareil

WARNING: Do not add any material to the appliance which will come in contact with the

ﬂames, other than that supplied by the manufacturer with the appliance.

AVERTISSEMENT: N’ajoutez pas à cet appareil aucun matériau devant entretien

contact avec les ﬂammes autre que celui qui est fourni avec cet appareil par le fabricant.

*** Maximum horizontal extension:

X”. See installation manual for

greater extensions, minimum vent

lengths and maximum vent lengths.

*** L’extension horizontale maximale: X”.

Référez au manuel d’installation pour des

extensions plus grandes, les longueurs

d’évacuation minimaux et maximum.

The appliance must be vented using the appropriate Napoleon vent kits. See installation

manual for venting speciﬁcations. Proper reinstallation and resealing is necessary after servicing

the vent-air intake system.

L’appareil doit être ventilé à l’aide de l’ensemble d’évacuation propre à Napoleon. Référez au

manuel d’installation pour les spéciﬁcations d’évacuation. Il est nécessaire de bien réinstaller et

resceller l’évacuation après avoir executer l’entretien du système de prise d’air.

Serial Number / N° de Série:

W385-XXXX

REFERENCE# 161746

XXXX

VENTED DECORATIVE GAS APPLIANCE: NOT A SOURCE OF

HEAT, NOT INTENDED FOR USE AS A HEATING

APPLIANCE, NOT FOR USE WITH SOLID FUEL.

APPAREIL À GAZ DÉCORATIF À ÉVACUATION: N’EST PAS

UNE SOURCE DE CHALEUR; N’EST PAS DESTINÉ À ÈTRE

UTILISÉ COMME UN APPAREIL DE CHAUFFAGE; NE

CONVIENT PAS AUX COMBUSTIBLES SOLIDES.

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS APPLIANCE ONLY.

POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE

CERTIFIÉES AVEC L’APPAREIL.

XX,XXX XX,XXX

For natural gas when equipped with No. XX drill size oriﬁce.

For propane when equipped with No. XX drill size oriﬁce.

Convient au gaz naturel quand l’appareil est muni d’un injecteur de diamètre no. XX.

Convient au propane quand l’appareil est muni d’un injecteur de diamètre no. XX.

Electrical rating: 115V, 60HZ. Less than 12 amperes.

Spéciﬁcations électriques: 115V, 60HZ. Moins de 12 ampère.

XX.X% XX.X%

XXXX XXXX XXXX XXXX

SAMPLE

É

l

é

vati

onévation

Ali

mentat

i

on

Alimentation

A

lim

e

ntati

o

n R

édu

it

eAlimentation Réduite

P

4

P4

w.c. (NG). (NG)

Pressure:

ure:

4.5” w.c. (NG

)4.5” w.c. (NG)

Pressure:

ssure:

7”* w.c.

(

N

G)7”* w.c. (NG)

teur:

ur:

3,5” d’une colonne d’eau

(

GN

)3,5” d’une colonne d’

ation Min.:

ion Min

4,5” d’une colonne d’eau

(G

N

)u (GN)

tion Max.:

ion Max.:

7” ** d’une colonne d’eau

(G

N

)7” ** d’une colonne d’eau (GN

sure not to exceed 13”.

re not to exceed 13”.

Manif

o

l

d

Pr

essu

r

e

:

old Pressure:

10” w.c.

(

P

).c. (P)

Minimum

S

u

pp

l

y

Pressure:

Minimum Supply Pressure:

11” w.c. (P

)11” w.c. (P)

Maximum

S

u

pp

l

y

Pressure:

Maximum Supply Pressure:

13”* w.c.

(

P

)13”* w.c. (P)

Pression au

C

ollecteur:

n au Collecteur:

10” d’une colonne d’eau

(

P

)0” d’une colonne d’eau (P)

Pre

ss

ion d’Alimentation Min.:

Pression d’Alimentation Min.:

11” d’une colonne d’eau

(

P

)11” d’une colonne d’eau (P)

Pre

ss

ion d’Alimentation Max.:

ession d’Alimentation Max.:

13” * d’une colonne d’eau

(

P

)13” * d’une colonne d’eau (P)

** Pression d’alimentation maximale ne devait pas dépasser 13”.** Pression d’alimentation maximale ne devait pas dépasser 13”.

to combustible materials: mbustible materials:

standoff spacers for framing and ﬁnishingoff spacers for framing and ﬁnishin

bustible framing and ﬁnishing materials, bustible framing and ﬁnishing materials

Dégagements minimaux des matériaux combustibDégagements minimaux des matériaux combu

Dessus, côtés et arrière: selon les espaces, côtés et arrière: selon les esp

pour les matériaux d’oss matériaux d

ANCE: NOT

CE: NOT

AT, NOT INTENDED FOR USE ANDED FOR USE A

APPLIANCE, NOT FOR USE WITHAPPLIANCE, NOT FOR

APPAREIL À GAZ DÉCORATIF À ÉVACUATIOAPPAREIL À GAZ DÉCORATIF À ÉVACUATIO

UNE SOURCE DE CHALEUR; N’EST PAS DESUNE SOURCE DE CHALEUR; N’EST PAS D

UTILISÉ COMME UN APPAREIL DE CHAUTILISÉ COMME UN APPAREIL DE CHA

CONVIENT PAS AUX COMBUSTIBLEONVIENT PAS AUX COMBUSTIBLE

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS APP

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS AP

POUR UTILISATION UNIQUEMENT AVELISATION UNIQUEMENT

XX,XXXXX,XXX

XX.X% XX.X%

note:

The rating plate must remain with the appliance at all times. It must not be removed.

1.3 mobile home installation

This appliance must be installed in accordance with the manufacturer’s instructions and the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home

Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas

indicated on the rating plate.

This mobile/manufactured home listed appliance comes factory equipped with a means to secure the appliance. Built

in appliances are equipped with 1/4” (6.4mm) diameter holes located in the front left and right corners of the base.

Use appropriate fasteners, inserted through the holes in the base to secure. For free standing products contact your

local authorized dealer / distributor for the appropriate securing kit. For mobile home installations, the appliance must

be fastened in place. It is recommended that the appliance be secured in all installations. Always turn off the pilot and

the fuel supply at the source, prior to moving the mobile home. After moving the mobile home and prior to lighting the

appliance, ensure that the logs are positioned correctly.

This appliance is certiﬁ ed to be installed in an aftermarket permanently located, manufactured (mobile) home,

where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible

for use with other gases, unless a certiﬁ ed kit is used.

Conversion Kits

This appliance is ﬁ eld convertible between Natural Gas (NG) and Propane (P).

To convert from one

g

as to another, consult

y

our Authorized dealer/distributor.

EN

W415-2357 / 12.19.19

7

general information

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

1.4 dimensions

W415-2357 / 12.19.19

EN

8

general information

37 5/8"

956mm

46"

1168mm

58"

1473mm

24"

610mm

28"

711mm

2"

51mm

13 7/8"

352mm

GAS

INLET

8 7/8"

225mm

21"

533mm

22 1/8"

562mm

14"

356mm

17 3/4"

451mm

7/8"

22mm

7"

178mm

DIA.

4"

102mm

DIA.

FRONT VIEW SIDE VIEW

TOP VIEW

!

WARNING

• Risk of ﬁ re. Maintain speciﬁ ed air space clearances to vent pipe and appliance.

• The vent system must be supported every 3’(0.9m) for both vertical and horizontal runs. Use support ring assembly W010-

0067 or equivalent non-combustible strapping to maintain the minimum clearance to combustibles for both vertical and

horizontal runs. Spacers are attached to the inner pipe at predetermined intervals to maintain an even air gap to the outer

pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each elbow to ensure this

gap is maintained. These spaces must not be removed.

This appliance uses a 4” (102mm) exhaust / 7” (178mm) air intake vent pipe system. Refer to the section applicable

to your installation.

For safe and proper operation of the appliance, follow the venting instructions exactly. Deviation from the minimum vertical

vent length can create difﬁ culty in burner start-up and/or carboning. Under extreme vent conﬁ gurations, allow several minutes

(5-15) for the ﬂ ame to stabilize after ignition. Although not a requirement, it is recommended for vent lengths that pass through

unheated spaces (attics, garages, crawl spaces) be insulated with the insulation wrapped in a protective sleeve to minimize

condensation. Provide a means for visually checking the vent connection to the appliance after the appliance is installed. Use a

ﬁ restop, vent pipe shield or attic insulation shield when penetrating interior walls, ﬂ oor or ceiling.

The vent terminal may be painted with a high temperature paint to match exterior colours. Use an outdoor paint suitable for

400°F (200°C). Application and performance of paint is the consumer’s responsibility. Spot testing is recommended.

For vent systems that provide seals on the inner exhaust ﬂ ue, only the outer air intake joints must be sealed using a red high

temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent pipe joints of all

other approved vent systems except for the exhaust vent pipe connection to the appliance ﬂ ue collar which must be sealed

using the black high temperature sealant Mill Pac. High temperature sealant must be ordered separately.

For optimum ﬂ ame appearance and appliance performance, keep the vent length and number of elbows to a minimum.

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that

it is unobstructed and undamaged.

Rigid and ﬂ exible venting systems must not be combined. Different venting manufacturer components must not

be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run is 20

feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of vent connections is two

horizontally or three vertically (excluding the appliance and the air terminal connections) when using ﬂ exible venting.

Horizontal runs may have a 0” rise per foot or 0mm rise per meter however for optimum performance it is recommended

that all horizontal runs have a minimum 1/4” rise per foot or 21mm rise per meter using ﬂ exible venting. For safe and proper

operation of the appliance, follow the venting instructions exactly.

Venting

System

Starter Adapter Part Number Supplier Website

Duravent W175-0053 Wolf Steel www.duravent.com

Amerivent 4DSC-N2 American Metal www.americanmetalproducts.com

Direct Temp 4DT-AAN Selkirk www.selkirkcorp.com

SureSeal 4DNA Metal-Fab www.mtlfab.com

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting components.

Minimum and maximum vent lengths, for both horizontal and vertical installations, clearances from vent pipes to combustibles

and air terminal locations as set out in this manual apply to all vent systems and must be adhered to. For Simpson Dura-Vent,

Selkirk Direct Temp, American Metal Amerivent and Metal-Fab, follow the installation procedure provided with the venting

components or on the website for your venting supplier.

A starter adaptor must be used with the following vent systems and may be purchased from the corresponding supplier:

note:

If for any reason the vent air intake system is disassembled, re-install per the instructions provided for the initial installation.

This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate

constructions such as a chimney as part of the vent system is not permitted.

This template must be used in conjunction with templates 7.1.1 or 7.1.2, depending on

termination shape (i.e. round, or round and square). See appropriate templates folder.

EN

W415-2357 / 12.19.19

9

2.0 venting

When using Wolf Steel venting components, use only approved Wolf Steel rigid / ﬂ exible components with the following ter-

mination kits: wall terminal kit GD-222, GD-222R, or 1/12 to 7/12 pitch roof terminal kit GD-110, 8/12 to 12/12 roof terminal

kit GD-111, ﬂ at roof terminal kit GD-112 or periscope kit GD-201 (for wall penetration below grade). With ﬂ exible venting, in

conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD-220 or the 10 foot (3.1m) vent kit GD-330.

For stoves only: wall terminal kit GD-175 (venting included).

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings

and serves both dwellings. Local codes or regulations may require different clearances.

Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼” (31.8mm) air gap

all around between the inner liner and outer liner is required for safe operation.

!

WARNING

• The ﬁ rst 2 feet of outer 7” (178mm) diameter vent pipe from the appliance must be wrapped in the 1” (25mm)

thick insulation sleeve (supplied). Make sure the insulation is pulled down tight to the appliance when installed.

Thereafter, a 2” (51mm) clearance all around the vent pipe from combustible materials on all horizontal vent

sections is required.

W415-2357 / 12.19.19

EN

10

venting

2.1 typical vent installation

10" (254mm)

MINIMUM

24" (610mm)

MAXIMUM

56"

(1422mm)

PLUS RISE

46"

(1168mm)

16" (406mm)

MINIMUM

3 FEET (1m)

MINIMUM

40 FEET (12m)

MAXIMUM

When venting, the horizontal run must be kept to a maximum of 20 feet (6m). If a 20 foot (6m) horizontal run is

required, the appliance must have a minimum vertical rise immediately off the appliance of 57" (1448mm). When

terminating vertically, the vertical rise is a minimum 3 feet (1m) and a maximum 40 feet (12m) above the appliance.

* FIRST TWO

FEET

REQUIRES

INSULATION

SLEEVE

46"

(1168mm)

EN

W415-2357 / 12.19.19

11

venting

2.2 special vent installations

2.2.1 periscope termination

Use the periscope kit to locate the air termination above grade. The periscope

must be installed so that when ﬁ nal grading is completed, the bottom air slot is

located a minimum 12” (305m) above grade. The maximum allowable vent length

(including both rise and run) is 10’ (3m).

30" (762mm)

MINIMUM*

12" (305mm)

MINIMUM

ABOVE

GRADE

* First two feet (0.6m) requires

insulation sleeve

46"

(1168mm)

W415-2357 / 12.19.19

EN

12

venting

2.3 minimum air terminal location clearances

Covered balcony applications ††*

Q

MIN

R

MAX

R

= 3 feet

(0.9m)

= 2 x

IHHW

(4.6m)

Q

ACTUAL

R

Q

S

G

P

INSTALLATIONS

CANADA U.S.A.

A

12” (30.5cm) 12” (30.5cm) Clearance above grade, veranda porch, deck or balcony.

B

12” (30.5cm)

Δ

9” (229mm)

Δ

Clearance to windows or doors that open.

C

12” (30.5cm)* 12” (30.5cm)* Clearance to permanently closed windows.

D

18”

(45.7cm)**

18”

(45.7cm)**

Vertical clearance to ventilated sofﬁ ts located above the terminal within a horizontal distance of 2’ (0.6m)

from the center line of the terminal.

E

12” (30.5cm)** 12” (30.5cm)** Clearance to unventilated sofﬁ t.

F

0” (0mm) 0” (0mm) Clearance to an outside corner wall.

G

0” (0mm)*** 0” (0mm)***

Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

2” (51mm)*** 2” (51mm)*** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

H

3’(0.9m) 3’(0.9m)****

Clearance to each side of the center line extended above the meter / regulator assembly to a maximum

vertical distance of 15’ (4.6m).

I

3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.

J

12” (30.5cm) 9” (229mm) Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.

K

6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.

L

7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.

M

12” (30.5cm)†† 12” (30.5cm)**** Clearance under a veranda, porch, deck or overhang.

N

16” (40.6cm) 16” (40.6cm) Clearance above the roof.

O

2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.

P

8’ (2.4m) 8’ (2.4m)

Roof must be non-combustible without openings.

Q

3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.

R

6’ (1.8m) 6’ (1.8m)

See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an opening

between the terminal and the open side of the structure.

S

12” (30.5cm) 12” (30.5cm) Clearance under a covered balcony

Δ The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad sofﬁ ts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements, check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the ﬂ oor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements, check local codes.

††* Permitted only if the balcony is fully open on a minimum of one side.

Clearances are to be in accordance with local

installation codes and the requirements of the gas

supplier. In their absence, clearances are to be as

listed above and are based on national codes.

note:

Wall terminals are for illustration purposes only. Size and

shapes may vary.

EN

W415-2357 / 12.19.19

13

venting

2.4 venting application ﬂ ow chart

2.5 deﬁ nitions

2.6 elbow vent length values

Top Exit

Horizontal Termination

Vertical rise is equal

to or greater than the

horizontal run

Vertical rise is equal

to or greater than the

horizontal run

Vertical rise is less

than horizontal run

Vertical rise is less

than horizontal run

Horizontal run +

vertical rise to

maximum of

24.75 feet (7.5m)

Horizontal run +

vertical rise to

maximum of

19 (5.8m)

4.2 times the vertical

rise equal to or

greater than the

horizontal run

3 times the vertical

rise equal to or

greater than the

horizontal run

Horizontal run +

vertical rise to

maximum of

40 feet (12.2m)

Horizontal run +

vertical rise to

maximum of

40 feet (12.2m)

Vertical Termination

For the following symbols used in the venting calculations and

examples are:

> - greater than

> - equal to or greater than

< - less than

< - equal to or less than

H

T

- total of both horizontal vent lengths (Hr) and offsets (Ho) in feet

H

R

- combined horizontal vent lengths in feet

H

O

- offset factor: .03 (total degrees of offset - 90°*) in feet

H

O

- offset factor: .03 (total degrees of offset - 135°*) in feet

V

T

- combined vertical vent lengths in feet

Feet Inches Millimeters

1° 0.03 0.5 12.7

15° 0.45 6.0 152.4

30° 0.9 11.0 279.4

45° 1.35 16.0 406.4

90°* 2.7 32.0 812.8

* The ﬁ rst 90° offset has a zero value and is shown in the formula as - 90°

* The ﬁ rst 45° and° offset have a zero value and is shown in the formula as -45° and -90° respectively

or -135° when combined (for 45° exit only).

W415-2357 / 12.19.19

EN

14

venting

2.7 horizontal termination

EN

Simple venting con¿ guration (only one 90° elbow)

(H

T

) < (V

T

)

For vent con¿ gurations requiring more than one 90° elbow, the following formulas apply:

Formula 1: H

T

< V

T

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

Example:

V

1

= 3 FT (0.9m)

V

2

= 8 FT (2.4m)

V

T

= V

1

+ V

2

= 3 FT (0.9m ) + 8 FT (2.4m) = 11 FT (3.4m)

H

1

= 2.5 FT (0.8m)

H

2

= 2 FT (0.6m)

H

R

= H

1

+ H

2

= 2.5 FT (0.8m) + 2 FT (0.6m) = 4.5 FT (1.4m)

H

O

= .03 (three 90° elbows - 90°) = .03 (270° - 90°) = 5.4 FT (1.7m)

H

T

= H

R

+ H

O

= 4.5 FT (1.4m) + 5.4 FT (1.6m) = 9.9 FT (3m)

H

T

+ V

T

= 9.9 FT (3m) + 11 FT (3.4m) = 20.9 FT (6.4m)

Formula 1: H

T

< V

T

9.9 FT (3m) < 11 FT (3.4m)

Formula 2: H

T

+ V

T

< 40 FT (12.2m)

20.9 FT (6.4m) < 40 FT (12.2m)

Since both formulas are met, this vent con guration is acceptable.

See graph to determine the required vertical

rise V

T

for the required horizontal run H

T

.

The shaded area within the lines represents

acceptable values for H

T

and V

T

0

2.5

(0.8)

5

(1.5)

7.5

(2.3)

10

(3.1)

12.5

(3.8)

15

(4.6)

40 (12.2)

10 (3.1)

20 (6.1)

30 (9.1)

17.5

(5.3)

20

(6.1)

39 (11.9)

REQUIRED

VERTICAL

RISE IN FEET

(METERS)V

T

HORIZONTAL VENT RUN PLUS OFFSET IN

FEET (METERS) H

T

90°

V

1

V

2

H

1

H

2

EN

W415-2357 / 12.19.19

15

venting

(H

T

) > (V

T

)

Simple venting configuration (only one 90° elbow)

See graph to determine the required vertical rise V

T

for the

required horizontal run H

T

.

REQUIRED

VERTICAL RISE

IN INCHES

(MILLIMETERS)

V

T

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERES) H

T

For vent configurations requiring more than one 90° elbow, the following formulas apply:

Formula 1: H

T

< 4.2 V

T

Formula 2: H

T

+ V

T

< 24.75 feet (7.5m)

Example:

V

1

= V

T

= 6 FT (1.8m)

H

1

= 3 FT (0.9m)

H

2

= 5 FT (1.5m)

H

R

= H

1

+ H

2

= 3FT (0.9m) + 5FT (1.5m) = 8 FT (2.4m)

H

O

= .03 (two 90° elbows - 90°) = .03 (180° - 90°) = 2.7FT (0.8m)

H

T

= H

R

+ H

O

= 8FT (2.4m) + 2.7FT (0.8m) = 10.7FT (3.3m)

H

T

+ V

T

= 10.7FT (3.3m) + 6FT (1.8m) = 16.7FT (5.1m)

Formula 1: H

T

< 4.2 V

T

4.2 V

T

= 4.2FT (1.3m) x 6FT (1.8m) = 25.2FT (7.7m)

10.7FT (3.3m) < 25.2FT (7.7m)

Formula 2: H

T

+ V

T

< 24.75 FT (7.5m)

16.7FT (5.1m) < 24.75 (7.5m)

Since both formulas are met, this vent configuration is acceptable.

0

5

(1.5)

15

(4.6)

20 (6.1)

100 (2540)

50 (1270)

150 (3810)

12.5

(3.8)

19 1/2

(495.3)

57 (1447.8)

147

(3733.8)

2

(0.6)

The shaded area within the lines represents acceptable

values for H

T

and V

T

90°

V

1

H

1

H

2

90°

Example:

V

1

= 4 FT (1.2m)

V

2

= 1.5 FT (0.5m)

V

T

= V

1

+ V

2

= 4FT (1.2m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

H

1

= 2 FT (0.6m)

H

2

= 1 FT (0.3m)

H

3

= 1 FT (0.3m)

H

4

= 1.5 FT (0.5m)

H

R

= H

1

+ H

2

+ H

3

+ H

4

= 2FT (0.6m) + 1FT (0.3m) + 1FT (0.3m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

H

O

= .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT (2.5m)

H

T

= H

R

+ H

O

= 5.5 FT (1.7m) + 8.1 FT (2.5m) = 13.6 FT (4.2m)

H

T

+ V

T

= 13.6 FT (4.2m) + 5.5 FT (1.7m) = 19.1 FT (5.8m)

Formula 1: H

T

< 4.2 V

T

4.2 V

T

= 4.2 FT (1.3m) x 5.5 FT(1.7m) = 23.1 FT (7m)

13.6 FT (4.2m) < 23.1 FT (7m)

Formula 2: H

T

+ V

T

< 24.75 FT (7.5m)

19.1FT (5.8m) < 24.75 FT (7.5m)

Since both formulas are met, this vent configuration is acceptable.

90°

H

1

H

2

V

1

V

2

H

3

H

4

10

(3.1)

19.5

(5.9)

0

5

(1.5)

15

(4.6)

20 (6.1)

100 (2540)

50 (1270)

150 (3810)

12.5

(3.8)

19 1/2

(495.3)

57 (1447.8)

147

(3733.8)

2

(0.6)

10

(3.1)

19.5

(5.9)

10" (254mm) MIN. RISE IF

MAX 42" (1067mm)

WITH MIN RISE.

H

T

W415-2357 / 12.19.19

EN

16

venting

2.8 vertical termination

(H

T

) < (V

T

)

Simple venting configurations.

See graph to determine the required vertical rise V

T

for the

required horizontal run H

T

.

REQUIRED

VERTICAL

RISE IN FEET

(METERS) V

T

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

T

For vent configurations requiring one or more 90° elbows the following formulas apply:

Formula 1: H

T

< V

T

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

Example:

V

1

= 5 FT (1.5m)

V

2

= 6 FT (1.8m)

V

3

= 10 FT (3.1m)

V

T

= V

1

+ V

2

+ V

3

= 5FT (1.5m) + 6FT (1.8m) + 10FT (3.1m) = 21FT (6.4m)

H

1

= 8 FT (2.4m)

H

2

= 2.5 FT (0.8m)

H

R

= H

1

+ H

2

= 8FT (2.4m) + 2.5FT (0.8m) = 10.5 FT (3.2m)

H

O

= .03 (four 90° elbows - 90°)

= .03 (360° - 90°) = 8.1 FT (2.5m)

H

T

= H

R

+ H

O

= 10.5FT (3.2m) + 8.1FT (2.5m) = 18.6FT (5.7m)

H

T

+ V

T

= 18.6FT (5.7m) + 21FT (6.4m) = 39.6FT (12.1m)

Formula 1: H

T

< V

T

18.6FT (5.7m) < 21FT (6.4m)

Formula 2: H

T

+ V

T

< 40 FT (12.19m)

39.6FT (12.1m) < 40FT (12.2m)

Since both formulas are met, this vent configuration is acceptable.

90°

V

1

V

2

H

1

H

2

The shaded area within the lines represents acceptable

values for H

T

and V

T

90°

0

5

(1.5)

10

(3.1)

15

(4.6)

20

(6.1)

40 (12.2)

10 (3.1)

20 (6.1)

30 (9.1)

3 (0.9)

V

3

EN

W415-2357 / 12.19.19

17

venting

(H

T

) > (V

T

)

Simple venting configurations.

See graph to determine the required vertical rise V

T

for the

required horizontal run H

T

.

REQUIRED

VERTICAL

RISE IN FEET

(METERS) V

T

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

T

For vent configurations requiring more than two 90° elbows the following formulas apply:

Formula 1: H

T

< 3V

T

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

Example:

V

1

= 2 FT (0.6m)

V

2

= 1 FT (0.3m)

V

3

= 1.5 FT (0.5m)

V

T

= V

1

+V

2

+V

3

= 2FT (0.6m) + 1FT (0.3m) + 1.5FT (0.5m) = 4.5FT (1.4m)

H

1

= 6 FT (1.8m)

H

2

= 2 FT (0.6m)

H

R

= H

1

+ H

2

= 6FT (1.8m) + 2FT (0.6m) = 8 FT (2.4m)

H

O

= .03 (four 90° elbows - 90°)

= .03 (360° - 90°) = 8.1 FT (2.5m)

H

T

= H

R

+ H

O

= 8FT (2.4m) + 8.1FT (2.5m) = 16.1FT (4.9m)

H

T

+ V

T

= 16.1FT (4.9m) + 4.5FT (1.4m) = 20.6 FT (6.3m)

Formula 1: H

T

< 3V

T

3V

T

= 3FT (0.9m) x 4.5FT (1.4m) = 13.5FT (4.1m)

16.1FT (4.9m) > 13.5FT (4.1m)

Since this formula is not met, this vent configuration is unacceptable.

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

20.6FT (6.3m) < 40 (12.2m)

Since only formula 2 is met, this vent configuration is unacceptable and a new appliance location or vent configuration will

need to be established to satisfy both formulas.

The shaded area within the lines represents acceptable

values for H

T

and V

T

0

5

(1.5)

10

(3.1)

15

(4.6)

20

(6.1)

10 (3.1)

20 (6.1)

3 (0.9)

25

(7.6)

30

(9.1)

19 (5.8)

90°

V

1

V

2

H

1

H

2

90°

V

3

0

5

(1.5)

10

(3.1)

15

(4.6)

20

(6.1)

10 (3.1)

20 (6.1)

3 (0.9)

25

(7.6)

30

(9.1)

19 (5.8)

3

(0.9)

W415-2357 / 12.19.19

EN

18

3.0 installation

Horizontal runs may have a 0" (0mm) rise per foot in all cases using Wolf Steel, Simpson Dura-Vent, Selkirk Direct

Temp or American Metal Amerivent rigid vent components and Wolf Steel ﬂ exible vent components. For

optimum performance it is recommended that all horizontal runs have a minimum 1/4" (6.3mm) rise per foot using

ﬂ exible or rigid venting. For safe and proper operation of the appliance, follow the venting instructions exactly.

!

WARNING

• Ensure to unpack all loose materials from inside the ﬁ rebox prior to connecting the gas and electrical supply

• If your appliance is supplied with a remote, ensure the remote receiver is in the “OFF” position prior

to connecting the gas and electrical supply to the appliance.

• For safe and proper operation of the appliance, follow the venting instructions exactly.

• The appliance exhaust ﬂ ue collar must be sealed using Mill Pac. All exhaust and intake vent pipe joints

must be sealed using red RTV high temp silicone sealant (W573-0002) (not supplied) or black high temp Mill

Pac (W573-0007) (not supplied).

• If using pipe clamps to connect rigid vent components, a minimum of 3 screws must also be used to ensure

the connection cannot slip off.

• Do not clamp the ﬂ exible vent pipe.

• Risk of ﬁ re, explosion, or asphyxiation. Improper support of the entire venting system may allow vent to sag

and separate. Use vent run supports and connect vent sections per installation instructions.

• Risk of ﬁ re, do not allow loose materials or insulation to touch the vent pipe. Remove insulation to allow for the

installation of the attic shield and to maintain clearances to combustibles.

• Do not ﬁ ll the space between the vent pipe and enclosure with any type of material. Do not pack insulation

or combustibles between ceiling ﬁ restops. Always maintain speciﬁ ed clearances around venting and ﬁ restop

systems. Install wall shields and ﬁ restops as speciﬁ ed. Failure to keep insulation or other materials away from

vent pipe may cause ﬁ re.

• For gas stoves only: If the appliance is installed directly on carpeting, vinyl tile, or other combustible material

other than wood ﬂ ooring, the appliance shall be installed on a metal or wood panel extending the full width and

depth, unless otherwise tested.

EN

W415-2357 / 12.19.19

19

installation

3.1 horizontal installation

3.2 vertical installation

This application occurs when venting through an exterior

wall. Having determined the correct height for the air

terminal location, cut and frame a hole in the exterior wall,

as illustrated, to accommodate the ﬁ restop assembly. Dry

ﬁ t the ﬁ restop assembly before proceeding to ensure the

brackets on the rear surface ﬁ t to the inside surface of the

horizontal framing.

The length of the vent shield may be cut shorter for

combustible walls that are less than 8 1/2” (215.9mm)

thick but the vent shield must extend the full depth of the

combustible wall.

A. Apply a bead of caulking (not supplied) around the outer edge of

the hole of the ﬁ restop assembly, ﬁ t the ﬁ restop assembly to the

hole and secure using 4 screws.

B. Once the vent pipe is installed in its ﬁ nal position, apply red RTV silicone (W573-0002) (not supplied)

between the pipe and the ﬁ restop.

• The ﬁ restop assembly must be installed with the vent shield to the top.

• Terminals must not be recessed into a wall or siding more than the depth of the return ﬂ ange of the mounting

plate.

!

WARNING

Do not ﬁ ll the air space between the ﬁ restop spacer and the

exterior wall with any type of insulating material (i.e. spray foam).

note:

DETERMINE

THE

CORRECT

HEIGHT

CAULKING

FIRESTOP

SPACER

VENT

SHIELD

FINISHING

MATERIAL

CAULKING

note:

The above is for illustration purposes only. Vents

do not always pass through center of frame.

ADD

WIDTH

ADD

HEIGHT

This application occurs when venting through a roof. Installation kits for

various roof pitches are available from your authorized dealer / distributor.

See the “accessories” section to order speciﬁ c kits required.

A. Determine the air terminal location, cut and frame a square opening,

as illustrated, in the ceiling and the roof to provide the minimum 1"

(25mm) clearance between the vent pipe and any combustible material.

Try to center the vent pipe location midway between two joists to

prevent having to cut them. Use a plumb bob to line up the center of

the openings. A vent pipe shield will prevent any materials such as

insulation, from ﬁ lling up the 1" (25mm) air space around the pipe. Nail

headers between the joist for extra support.

B. Apply a bead of caulking (not supplied) to the framework or to the

Wolf Steel vent pipe shield plate or equivalent (in the case of a ﬁ nished

ceiling), and secure over the opening in the ceiling. A ﬁ restop must be

placed on the bottom of each framed opening in a roof or ceiling that

the venting system passes through. Apply a bead of caulking all around

and place a ﬁ restop spacer over the vent shield to restrict cold air from

being drawn into the room or around the ﬁ replace. Ensure that both

spacer and shield maintain the required clearance to combustibles.

Once the vent pipe is installed in its ﬁ nal position, apply red RTV

silicone (W573-0002) (not supplied) between the pipe and the ﬁ restop

assembly.

C. In the attic, slide the vent pipe collar down to cover up the open end

of the shield and tighten. This will prevent any materials, such as

insulation, from ﬁ lling up the 1" (25mm) air space around the pipe.

Caulking

Vent Pipe

Shield

Vent

Pipe

Shield

Vent

Pipe

Collar

Firestop

underside

of joist

11 3/4”

(30cm)

11 3/4”

(30cm)

W415-2357 / 12.19.19

EN

20

installation

3.3 using ﬂ exible venting components

3.4 horizontal air terminal installation

For safe and proper operation of the appliance, follow the venting instructions

exactly.

The vent system must be supported approximately every 3 feet (0.9m) for

both vertical and horizontal runs. Use Wolf Steel Ltd. support ring assembly

or equivalent noncombustible strapping to maintain the minimum clearance to

combustibles for both vertical and horizontal runs.

All inner ﬂ ex pipe and outer ﬂ ex pipe joints may be sealed using high temperature

red RTV silicone W573-0002 (not supplied) or the high temperature sealant W573-

0007 Mill Pac (not supplied). However, the high temperature sealant W573-0007

Mill Pac (not supplied) must be used on the joint connecting the inner ﬂ ex pipe and

the exhaust ﬂ ue collar.

Use only approved ﬂ exible vent pipe kits marked:

“Wolf Steel Approved Venting” or “E2” as identiﬁ ed by the stamp only on the ﬂ ex pipes.

Elbow

Spacers

• Do not allow the inner ﬂ ex pipe to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight.

• Spacers are attached to the inner ﬂ ex pipe at predetermined intervals to maintain an even air gap to the outer

ﬂ ex pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each

elbow to ensure this gap is maintained. These spacers must not be removed.

!

WARNING

A. Stretch the inner ﬂ ex pipe to the required length taking

into account the additional length needed for the ﬁ nished

wall surface. Apply a heavy bead of the red RTV silicone

(W573-0002) (not supplied) to the inner sleeve of the air

terminal. Slip the vent pipe a minimum of 2” (50.8mm)

over the inner sleeve of the air terminal and secure with a

minimum of 3 screws.

B. Using the outer ﬂ ex pipe, slide over the outer combustion

air sleeve of the air terminal and secure with a minimum

of 3 screws. Seal using red RTV silicone (W573-0002)

(not supplied).

C. Insert the vent pipes through the ﬁ restop maintaining

the required clearance to combustibles. Holding the air

terminal (lettering in an upright, readable position), secure

to the exterior wall and make weather tight by sealing

with caulking (not supplied).

D. If more vent pipe needs to be used to reach the ﬁ replace,

couple them together, as illustrated. The vent system

must be supported approximately every 3 feet (0.9m) for

both vertical and horizontal runs. Use non-combustible

strapping to maintain the minimum clearance to

combustibles.

E. Stove Appliances Only: From inside the house, using

Red RTV Silicone (W573-0002) (not supplied), seal

between the vent pipe and the ﬁ restop. Then slide the black trim collar over the vent pipe up to the

ﬁ restop.

The air terminal mounting plate may be recessed into the exterior wall or siding no greater than the

depth of its return ﬂ ange.

ADD FA

S

TENER TYP

E

ADD GRAPHIC

Screws

(Supplied)

2" (50.8mm) Overlap

Outer Flex Pipe

Inner Flex

Pipe

Caulking

Red RTV Silicone

Screws

Inner Coupler

Outer Coupler

Outer Flex

Pipe

Inner Flex

Pipe

Outer Flex

Pipe

Red RTV Silicone

La page est en cours de chargement...

NAPOLEON GD82NT-TESB Manuel utilisateur

NAPOLEON GD82NT-TESB Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents