Continental Fireplaces CDVS600-1NSB Le manuel du propriétaire

FRENCH

PG. 59

W415-2361 / A / 10.31.19

ADD MANUAL TITLE

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.continentalﬁ replaces.com • hearth@continentalﬁ replaces.com

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

NATURAL GAS MODELS:

PROPANE GAS MODELS:

Product Name / Code

(MUST use title from Price Book)

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

CSA /

INTERTEK

LOGO

SAFETY INFORMATION

- Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity of

this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the ﬁ re department.

- Installation and service must be performed

by a qualiﬁ ed installer, service agency, or the

supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certiﬁ ed kit is used.

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

WARNING

!

ENGLISH

$10.00

FOR INDOOR USE ONLY

IF INSTALLATION + OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

SHOWN WITH OPTIONAL

TRIVET

SAFETY BARRIER

CDVS600-1N / CS600-1N

CDVS600-1P / CS600-1P

INSTALLATION AND

OPERATION MANUAL

Gas Stoves Series

(CDVS600-1 illustrated)

W415-2361 / A / 10.31.19

EN

2

safety information

• This appliance is hot when operated and

can cause severe burns if contacted.

• Any changes or alterations to this

appliance or its controls can be

dangerous and is prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure

to operate appliance according to operating

instructions could cause ﬁ re or injury.

• Ensure the glass door is opened or removed

when lighting the pilot for the ﬁ rst time and

when the gas supply has run out.

• Risk of ﬁ re or asphyxiation, do not operate

appliance with ﬁ xed glass removed and never

obstruct the front opening of the appliance.

• Do not connect 110 volts to the control valve,

with the exception of models; GSST8 and

GT8.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during

installation. Sheet metal edges may be sharp.

• Do not burn wood or other materials in this appliance.

• Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing

and operating the appliance.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at

test pressures above 1/2 psig. Close the manual shut-off valve before pressure testing gas line at test

pressures equal to or less than 1/2 psig (35mb).

• The appliance must not be operated at temperatures below freezing (32°F / 0°C). Allow the appliance

to warm to above freezing prior to operation, with the exception of models; GSS36, GSS42; these

appliances are suitable for 0°F / -18°C.

• Children and adults should be alerted to hazards of high surface temperature and should stay

away to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the

appliance. Toddlers, young children and others may be susceptible to accidental contact

burns. A physical barrier is recommended if there are at risk individuals in the house. To

restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers,

young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from

furniture and draperies.

• Furniture or other objects must be kept a minimum of 4 feet (1.22m) away from the front of the appliance.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is off, it will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior

to operating the appliance.

• It is imperative that the control compartments, burners and circulating blower and its passageway in the

appliance and venting system are kept clean. The appliance and its venting system should be inspected

before use and at least annually by a qualiﬁ ed service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and

free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it

serviced. Keep burner and control compartment clean.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not allow wind or fans to blow directly into the appliance. Avoid any drafts that alter burner ﬂ ame

patterns.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

DANGER

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with this appliance and

shall be installed for the protection of children and other

at-risk individuals.

!

WARNING

EN

W415-2361 / A / 10.31.19

3

safety information

!

WARNING

• Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this

appliance.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has

been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass

should be done by a licensed or qualiﬁ ed service person, if equipped.

• Do not strike or slam shut the appliance glass door, if equipped.

• Only doors / optional fronts certiﬁ ed with the appliance are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Carbon or soot should not occur in a vent free appliance as it can distribute into the living area of your

home. If you notice any signs of carbon or soot, immediately turn off your appliance and arrange to have

it serviced by a qualiﬁ ed technician before operating it again.

• If equipped, the screen must be in place (closed) when the appliance is in operation.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating

to prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of

the exhaust escaping through these openings can also cause the surrounding combustible materials to

overheat and catch ﬁ re.

• Carbon monoxide poisoning may lead to death; early signs of carbon monoxide poisoning resemble the

ﬂ u, with headache, dizziness and/or nausea. If you have these signs, the appliance may not be working

properly. Get fresh air at once! Have appliance serviced. Some people; pregnant women, persons with

heart or lung disease, anemia, those under the inﬂ uence of alcohol, those at high altitudes are more

affected by carbon monoxide than others. Failure to keep the primary air opening(s) of the burner(s) clean

may result in sooting and property damage.

• As with any combustion appliance, we recommend having your appliance regularly inspected and

serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and

your family against Carbon Monoxide (not applicable for outdoor appliances).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a TV or other electronic components.

• For appliances equipped with a safety barrier; if the barrier becomes damaged, the barrier

shall be replaced with the manufacturer’s barrier for this appliance.

• Installation and repair should be done by a qualiﬁ ed service person. It is imperative that control

compartments, burners and circulating air passageways of the appliance be kept clean.

• For outdoor products only: this appliance must not be installed indoors or within any structure that

prevents or inhibits the exhaust gases from dissipating in the outside atmosphere.

• If applicable, the millivolt version of this appliance uses and requires a fast acting thermocouple. Replace

only with a fast acting thermocouple supplied by Wolf Steel Ltd.

!

WARNING

!

Disconnect the appliance main gas valve/control

from the supply piping when pressure testing that

system at pressures in excess of 1/2 psi (3.5 kPa).

Isolate the appliance with it’s shut off valve during

any pressure testing of the supply piping at

pressures equal to or less than 1/2 psi (3.5 kPa).

FIRE RISK HAZARD / DELAYED IGNITION

High supply pressure will damage the valve / controls.

Add California Prop 65 warning

!

WARNING:

This product can expose you to chemicals including lead and lead compounds,

which are known to the State of California to cause cancer, and chemicals including carbon

monoxide, which are known to the State of California to cause birth defects or other reproduc-

tive harm. For more information, go to www.P65Warnings.ca.gov.

W415-2361 / A / 10.31.19

EN

4

table of contents

NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.

1.0 general information 5

1.1 rating plate information 7

1.2 dimensions 7

1.3 shipping bracket 8

2.0 direct venting - model CDVS600-1 9

2.1 typical vent installations 10

2.2 special vent installations 12

2.2.1 periscope termination 12

2.2.2 corner termination 12

2.3 vent terminal clearances 13

2.4 venting application ﬂ ow chart 14

2.5 deﬁ nitions 15

2.6 elbow vent length values 15

2.7 top exit horizontal termination 16

2.8 top exit horizontal termination 17

2.9 rear exit horizontal termination 18

2.10 top or rear exit vertical termination 20

3.0 installation preparation - model

CDVS600-1 22

3.1 oriﬁ ce replacement 22

3.2 changing a top vent to a rear vent 23

4.0 installation 24

4.1 minimum clearance to combustibles 24

4.1.1 horizontal installation 25

4.1.2 vertical installation 26

4.1.3 horizontal air terminal installation -

model CDVS600-1 27

4.1.4 vertical air terminal installation - model

CDVS600-1 28

4.2 appliance vent connection - model

CDVS600-1 29

4.3 vertical through existing chimney 30

4.4 mobile home installation - model

CDVS600-1 31

4.5 gas installation 31

4.6 optional wall switch 31

4.7 natural vent speciﬁ cs - model CS600-1

32

4.7.1 chimney installation 32

4.7.2 installing natural vent 33

4.7.3 natural vent 33

4.7.4 combustion air 33

4.7.5 adding vent sections 34

4.7.6 installing ﬂ ashing and storm collar 35

5.0 finishing 36

5.1 front cast removal 36

5.2 safety barrier installation and removal 36

5.3 glass door installation and removal 37

5.4 battery housing installation 38

5.5 glass / door replacement 38

5.6 log placement 39

5.7 logo placement 40

5.8 switch and bracket installation 40

6.0 optional blower installation 41

7.0 wiring diagram 42

8.0 operation 43

8.1 operating instructions 43

8.2 pilot-on-demand 44

8.3 operating instructions - for your safety

read before operating 45

8.4 lighting instructions 45

9.0 adjustment 46

9.1 pilot burner adjustment 46

9.2 venturi adjustment 46

9.3 ﬂ ame characteristics 47

9.4 restricting vertical vents - model

CDVS600-1 47

10.0 maintenance 48

10.2 annual maintenance 49

10.1 care of glass 49

11.0 replacement parts 50

11.1 overview 51

11.2 valve train assembly 52

12.0 accessories 53

13.0 troubleshooting 54

14.0 warranty 56

15.0 service history 57

Batteries must be disposed of according to the local laws and regulations. Some batteries may be

recycled, and may be accepted for disposal at your local recycling center. Check with your

municipality for recycling instructions.

EN

W415-2361 / A / 10.31.19

5

standard checklist

1.0 general information

CDVS600-1 CS600-1

NG P NG P

Altitude (FT) 0-4,500 0-4500

Max. Input (BTU/

HR)

35,000 (Top vent)

21, 000 (Rear vent only)

31,500 (Top vent)

21,000 (Rear vent only)

35, 000 31,500

Max. Output (BTU/

HR)

27,300 24,570 27,300 24,570

Min. Inlet Gas

Supply Pressure

4.5" (11mb)

Water Column

11" (27mb)

Water Column

4.5" (11mb)

Water Column

11" (27mb)

Water Column

Max. Inlet Gas

Supply Pressure

7" (17mb)

Water Column

13" (32mb) W

ater Column

7" (17mb)

Water Column

13" (32mb)

Water Column

Manifold Pressure

(Under Flow

Conditions)

3.5" (9mb)

Water Column

10" (25mb)

Water Column

3.5" (9mb)

Water Column

10" (25mb)

Water Column

Installer, please ﬁ ll out the following information:

Customer:

Address:

Date of Installation:

Location of appliance:

Installer:

Dealer/Distributor contact number:

Serial #:

Model:

Natural Gas: CDVS600-1N

CS600-1N

Propane: CDVS600-1P

CS600-1P

When the appliance is installed at elevations above 4,500ft (1371m), and in the absence of speciﬁ c recommendations from

the local authority having jurisdiction, the certiﬁ ed high altitude input rating shall be reduced at the rate of 4% for each ad-

ditional 1,000ft (305m).

Change in ﬂ ame appearance from "HI" to "LO" is more evident in natural gas than in propane.

Expansion / contraction noises during heating up and cooling down cycles are normal and to be expected.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for

use with other gases, unless a certiﬁ ed kit is used.

CDVS600-1 - This appliance is not approved for closet or recessed installations. It is approved for bathroom,

bedroom and bedsitting room installations. This appliance may be installed in an aftermarket permanently located,

manufactured (mobile) home, where not prohibited by local codes. (Rear vent) Rear exit installations which termi-

nate horizontally and have no vertical vent runs must have the BTU input reduced to 21,000 BTU/hr by changing

the oriﬁ ce (supplied).

CS600-1- This appliance is approved for bedroom and bed-sitting room installations.

W415-2361 / A / 10.31.19

EN

6

general information

When the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ oor-

ing, the appliance shall be installed on a metal or wood panel extending the full width and depth.

The appliance, when installed with a blower, must be electrically connected and grounded in accordance with

local codes. In the absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the

ANSI/NFPA 70-1996 National Electrical Code in the United States. The blower power cord must be connected

into a properly grounded receptacle. The grounding prong must not be removed from the cord plug.

THIS GAS APPLIANCE MUST BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local

codes. Installation practices vary from region to region and it is important to know the speciﬁ cs that apply to your area, for

example in the state of Massachusetts:

• This product must be installed by a licensed plumber or gas ﬁ tter when installed within the commonwealth of

Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas

log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂ exible connector must not be longer than 36 inches (0.9m).

• A carbon monoxide detector is required in all rooms containing gas ﬁ red appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed

combustion product.

The installation must conform with local codes or, in absence of local

codes, the National Gas and Propane Installation Code CSA B149.1

in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54

in the United States. Suitable for mobile home installation if installed

in accordance with the current standard CAN/CSA Z240MH Series,

for gas equipped mobile homes, in Canada or ANSI Z223.1 and

NFPA 54 in the United States.

The appliance and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing

of that system at test pressures in excess of 1/2 psig (35 mb).

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any

pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (35 mb). When installed

with a blower or fan, the junction box must be electrically connected and grounded in accordance with local codes. In the

absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI / NFPA 70 National

Electric Code in the United States. In the case where the blower is equipped with a power cord, it must be connected into a

properly grounded receptacle. The grounding prong must not be removed from the cord plug.

The following does not apply to inserts; as long as the required clearance to combustibles is maintained, the most desirable

and beneﬁ cial location for an appliance is in the center of a building, thereby allowing the most efﬁ cient use of the heat

created. The location of windows, doors and, the trafﬁ c ﬂ ow in the room where the appliance is to be located should be

considered. If possible, you should choose a location where the vent will pass through the house without cutting a ﬂ oor or

roof joist. If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ ooring, the

appliance shall be installed on a metal or wood panel extending the full width and depth, unless otherwise tested.

We suggest that our gas

hearth products be installed

and serviced by professionals

who are certied in the U.S.

by the National Fireplace

Institute

®

(NFI) as NFI Gas

Specialists

www.ncertied.org

• Always light the pilot - whether for the ﬁ rst time or if the gas supply has run out - with the glass door opened or

removed.

• Provide adequate clearance for servicing and operating the appliance.

• Provide adequate ventilation.

• Never obstruct the front opening of the appliance.

• Objects placed in front of the appliance must be kept a minimum of 48" (121.9cm) from the front face of the

appliance.

• Surfaces around and especially above the appliance can become hot. Avoid contact when the appliance is

operating.

• Fire risk. Explosion hazard.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at test pressures

above 1/2psig. Close the manual shut-off valve before pressure testing gas line at test pressures equal to or

less than 1/2psig (35mb).

• Use only Wolf Steel-approved optional accessories and replacement parts with this appliance. Using non-listed

accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could result in a safety

hazard and will void the warranty and certiﬁ cation.

!

WARNING

EN

W415-2361 / A / 10.31.19

7

general information

32"

813mm

30 1/2"

775mm

17 7/8"

454mm

19 1/2"

495mm

24"

610mm

27"

686mm

5 1/2"

140mm

4"

102mm

DIA.

7"

178mm

DIA.

SAFETY BARRIER

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

NOTE: The rating plate must remain with the appliance at all times. It must not be removed.

1.1 rating plate information

SAMPLE

Certiﬁed to Canadian and American National Standards: CSA 2.22-XXXX / ANSI Z21.50-XXXX for Vented Decorative Gas Appliances

Certiﬁé selon les normes Nationales Canadiennes et Américaines: CSA 2.22-XXXX / ANSI Z21.50-XXXX pour les Appareils à gaz décoratif à évacuation

Direct vent, vented gas ﬁreplaces. Approved for bedroom, bathroom and bed-sitting room installation. Suitable for mobile home installation, if installed in accordance with the current

standard CAN / CSA Z240MH Series gas equipped mobile homes in Canada, or, in the United States, the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part

3280. When this US Standard is not applicable, use the Standard for Fire Safety Criteria for Manufactured Home Installations, Sites and Communities, ANSI / NFPA 501A. This appliance

must be installed in accordance with local codes, if any; if none, follow the current ANSI Z223.1 or CSA B149. For use with barrier WXXX-XXXX. Follow installation instructions.

Foyer à gaz ventilé. Homologué pour installation dans une chambre à coucher, une salle de bain et un studio. Approprié pour installation dans une maison mobile si son installation

conforme aux exigences de la norme CAN / CSA Z240MH Séries de maisons mobile équipées au gaz en vigueur au Canada, ou, aux États-Unis selon la norme 24 CFR, Part 3280,

Manufactured Home Construction and Safety Standard. Dans le cas ou cette norme d’États-Unis n’est pas pertinentes, utiliser la norme NFPA 501A, Fire Safety Criteria for Manufactured

Home Installations, Sites and Communities. Installer l’appareil selon les codes ou règlements locaux ou, en l’absence de tels règlements, selon les codes d’installation ANSI Z223.1 ou

CSA B149 en vigueur. Utiliser uniquement avec l’écran WXXX-XXXX. Suivre les instructions d’installation.

9700539 (WSL) 4001658 (NAC) 4001657 (NGZ) 4001659 (WUSA)

WOLF STEEL LTD. 24 Napoleon Road, Barrie, ON, L4M 0G8 Canada

XXXX XXXX XXXX XXXX

MODEL / MODÈLE

Altitude

Input

Reduced Input

P4

Élévation

Alimentation

Alimentation Réduite

P4

Manifold Pressure: 3.5” w.c. (NG)

Minimum Supply Pressure: 4.5” w.c. (NG)

Maximum Supply Pressure: 7”* w.c. (NG)

Pression au Collecteur: 3,5” d’une colonne d’eau (GN)

Pression d’Alimentation Min.: 4,5” d’une colonne d’eau (GN)

Pression d’Alimentation Max.: 7” ** d’une colonne d’eau (GN)

** Maximum inlet pressure not to exceed 13”.

Manifold Pressure: 10” w.c. (P)

Minimum Supply Pressure: 11” w.c. (P)

Maximum Supply Pressure: 13”* w.c. (P)

Pression au Collecteur: 10” d’une colonne d’eau (P)

Pression d’Alimentation Min.: 11” d’une colonne d’eau (P)

Pression d’Alimentation Max.: 13” * d’une colonne d’eau (P)

** Pression d’alimentation maximale ne devait pas dépasser 13”.

0-XXXXft (0-XXXXm)

Minimum clearance to combustible materials:

Top, sides & back: per standoff spacers for framing and ﬁnishing

materials. For non-combustible framing and ﬁnishing materials,

see installation manual.

Top X”

Floor X”

Sides X”

Back X”

Vent top X”

Vent sides & bottom X”

Recessed depth X”

*** Mantel X” from appliance opening

Dégagements minimaux des matériaux combustibles:

Dessus, côtés et arrière: selon les espaceurs de dégagements

pour les matériaux d’ossature selon le manuel du propriétaire

pour les matériaux de ﬁnition.

Dessus X”

Plancher X“

Côtés X”

Arrière X“

Dessus du conduit d’évent X”

Côtés et dessous du conduit d’évent X”

Profondeur d’encastré une face X”

*** Tablette X” de l’ouverture de l’appareil

WARNING: Do not add any material to the appliance which will come in contact with the

ﬂames, other than that supplied by the manufacturer with the appliance.

AVERTISSEMENT: N’ajoutez pas à cet appareil aucun matériau devant entretien

contact avec les ﬂammes autre que celui qui est fourni avec cet appareil par le fabricant.

*** Maximum horizontal extension:

X”. See installation manual for

greater extensions, minimum vent

lengths and maximum vent lengths.

*** L’extension horizontale maximale: X”.

Référez au manuel d’installation pour des

extensions plus grandes, les longueurs

d’évacuation minimaux et maximum.

The appliance must be vented using the appropriate Napoleon vent kits. See installation

manual for venting speciﬁcations. Proper reinstallation and resealing is necessary after servicing

the vent-air intake system.

L’appareil doit être ventilé à l’aide de l’ensemble d’évacuation propre à Napoleon. Référez au

manuel d’installation pour les spéciﬁcations d’évacuation. Il est nécessaire de bien réinstaller et

resceller l’évacuation après avoir executer l’entretien du système de prise d’air.

Serial Number / N° de Série:

W385-XXXX

REFERENCE# 161746

XXXX

VENTED DECORATIVE GAS APPLIANCE: NOT A SOURCE OF

HEAT, NOT INTENDED FOR USE AS A HEATING

APPLIANCE, NOT FOR USE WITH SOLID FUEL.

APPAREIL À GAZ DÉCORATIF À ÉVACUATION: N’EST PAS

UNE SOURCE DE CHALEUR; N’EST PAS DESTINÉ À ÈTRE

UTILISÉ COMME UN APPAREIL DE CHAUFFAGE; NE

CONVIENT PAS AUX COMBUSTIBLES SOLIDES.

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS APPLIANCE ONLY.

POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE

CERTIFIÉES AVEC L’APPAREIL.

XX,XXX XX,XXX

For natural gas when equipped with No. XX drill size oriﬁce.

For propane when equipped with No. XX drill size oriﬁce.

Convient au gaz naturel quand l’appareil est muni d’un injecteur de diamètre no. XX.

Convient au propane quand l’appareil est muni d’un injecteur de diamètre no. XX.

Electrical rating: 115V, 60HZ. Less than 12 amperes.

Spéciﬁcations électriques: 115V, 60HZ. Moins de 12 ampère.

XX.X% XX.X%

XXXX XXXX XXXX XXXX

1.2 dimensions

W415-2361 / A / 10.31.19

EN

8

general information

1.3 shipping bracket

SHIPPING BRACKET REMOVAL

A. Remove the four screws holding the shipping bracket to the

bottom of the appliance.

B. Lift the appliance off the skid and set on a ﬂ at surface.

C. Discard the screws, brackets and skid.

GLASS DOOR REMOVAL

A. Lift the top casting off.

B. Open the valve control cover. Pull the latch handles forward to

release. The door may now be safely removed by swinging the

bottom out and lifting it off.

SHIPPING BRACKET

LATCH

• The top casting is not fastened to the stove assembly. It simply sits on the stove as a lid. For shipping purposes,

it is held in place by plastic strapping. Once the strapping is cut, the top should be lifted off carefully and stored

in a safe place to avoid damage while completing the installation of the stove. To avoid the appliance being

damaged during shipping, a shipping bracket has been used and must be unbolted before the appliance can

be installed.

!

WARNING

EN

W415-2361 / A / 10.31.19

9

direct venting - model CDVS600-1

2.0 direct venting - model CDVS600-1

!

WARNING

• Risk of ﬁ re. Maintain speciﬁ ed air space clearances to vent pipe and appliance.

• The vent system must be supported every 3’(0.9m) for both vertical and horizontal runs. Use support ring assembly W010-

0067 or equivalent non-combustible strapping to maintain the minimum clearance to combustibles for both vertical and

horizontal runs. Spacers are attached to the inner pipe at predetermined intervals to maintain an even air gap to the outer

pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each elbow to ensure this

gap is maintained. These spaces must not be removed.

This appliance uses a 4” (102mm) exhaust / 7” (178mm) air intake vent pipe system. Refer to the section applicable

to your installation.

For safe and proper operation of the appliance, follow the venting instructions exactly. Deviation from the minimum vertical

vent length can create difﬁ culty in burner start-up and/or carboning. Under extreme vent conﬁ gurations, allow several minutes

(5-15) for the ﬂ ame to stabilize after ignition. Although not a requirement, it is recommended for vent lengths that pass through

unheated spaces (attics, garages, crawl spaces) be insulated with the insulation wrapped in a protective sleeve to minimize

condensation. Provide a means for visually checking the vent connection to the appliance after the appliance is installed. Use a

ﬁ restop, vent pipe shield or attic insulation shield when penetrating interior walls, ﬂ oor or ceiling.

The vent terminal may be painted with a high temperature paint to match exterior colours. Use an outdoor paint suitable for

400°F (200°C). Application and performance of paint is the consumer’s responsibility. Spot testing is recommended.

For vent systems that provide seals on the inner exhaust ﬂ ue, only the outer air intake joints must be sealed using a red high

temperature silicone (RTV). This same sealant may be used on both the inner exhaust and outer intake vent pipe joints of all

other approved vent systems except for the exhaust vent pipe connection to the appliance ﬂ ue collar which must be sealed

using the black high temperature sealant Mill Pac. High temperature sealant must be ordered separately.

For optimum ﬂ ame appearance and appliance performance, keep the vent length and number of elbows to a minimum.

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that

it is unobstructed and undamaged.

Rigid and ﬂ exible venting systems must not be combined. Different venting manufacturer components must not

be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run is 20

feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of vent connections is two

horizontally or three vertically (excluding the appliance and the air terminal connections) when using ﬂ exible venting.

Venting

System

Starter Adapter Part Number Supplier Website

Duravent W175-0053 Wolf Steel www.duravent.com

Amerivent 4DSC-N2 American Metal www.americanmetalproducts.com

Direct Temp 4DT-AAN Selkirk www.selkirkcorp.com

SureSeal 4DNA Metal-Fab www.mtlfab.com

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp, American Metal Amerivent or Metal-Fab venting components.

Minimum and maximum vent lengths, for both horizontal and vertical installations, clearances from vent pipes to combustibles

and air terminal locations as set out in this manual apply to all vent systems and must be adhered to. For Simpson Dura-Vent,

Selkirk Direct Temp, American Metal Amerivent and Metal-Fab, follow the installation procedure provided with the venting

components or on the website for your venting supplier.

A starter adaptor must be used with the following vent systems and may be purchased from the corresponding supplier:

note:

If for any reason the vent air intake system is disassembled, re-install per the instructions provided for the initial installation.

This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate

constructions such as a chimney as part of the vent system is not permitted.

This template must be used in conjunction with templates 7.1.1 or 7.1.2, depending on

termination shape (i.e. round, or round and square). See appropriate templates folder.

When using Wolf Steel venting components, use only approved Wolf Steel rigid / ﬂ exible components with the following ter-

mination kits: wall terminal kit GD-222, GD-222R, or 1/12 to 7/12 pitch roof terminal kit GD-110, 8/12 to 12/12 roof terminal

kit GD-111, ﬂ at roof terminal kit GD-112 or periscope kit GD-201 (for wall penetration below grade). With ﬂ exible venting, in

conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD-220 or the 10 foot (3.1m) vent kit GD-330.

For stoves only: wall terminal kit GD-175 (venting included).

GDS924N

W415-2361 / A / 10.31.19

EN

10

direct venting - model CDVS600-1

2.1 typical vent installations

TOP VENT

REAR VENT

24"

(61cm)

16" (40.6cm)

min.

40 ft. (12m)

max.

34" (864mm)

min.

40 ft. (12m)

max.

34" (864mm) min.

Horizontal runs may have a 0” rise per foot or 0mm rise per meter however for optimum performance it is recommended

that all horizontal runs have a minimum 1/4” rise per foot or 21mm rise per meter using ﬂ exible venting. For safe and proper

operation of the appliance, follow the venting instructions exactly.

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings

and serves both dwellings. Local codes or regulations may require different clearances.

Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼” (31.8mm) air gap

all around between the inner liner and outer liner is required for safe operation.

If approved for use with a power vent kit, state: “This appliance is certiﬁ ed for use with a

power vent kit. Contact your local authorized dealer for more information.”

If not, cover with a white box.

Use a ﬁ restop when penetrating interior walls, ﬂ oor or ceiling.

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between

two single family dwellings and serves both dwellings. Local codes or regulations may require different

clearances.

Use only Wolf Steel, Simpson Dura-Vent, Selkirk Direct Temp or American Metal Amerivent venting components.

Minimum and maximum vent lengths, for both horizontal and vertical installations, and air terminal locations for

either systems are set out in this manual and must be adhered to.

30 1/2"

(77.5cm)

16" (40.6cm)

min.

EN

W415-2361 / A / 10.31.19

11

direct venting - model CDVS600-1

20 ft. (6m)

max.

12” (305mm)

min. to grade

24” (610mm) min.

regardless of

horizontal vent length

Max. horizontal run

34" (86.4cm) max.

29" (73.7cm)

min.

59 1/2"

(151.1cm)

min. plus rise*

24" (61cm) max.

24" (61cm)

min. plus rise*

* See "venting" section.

W415-2361 / A / 10.31.19

EN

12

direct venting - model CDVS600-1

Use the periscope kit to locate the air termination above grade. The periscope must be installed so that when

ﬁ nal grading is completed, the bottom air slot is located a minimum 12” (305mm) above grade. The maximum

allowable vent length (including both rise and run) is 10’ (3m) for a ﬁ replace and 8’ (2m) for a stove. An insulation

sleeve is illustrated in the top vent image below, use only when supplied with the appliance.

(The insulation sleeve is not required with a stove appliance)

TOP VENTREAR VENT

24” (610mm)

MAXIMUM

0” (0mm) RISE

CORNER INSTALLATION

2.2 special vent installations

29"

(73.7cm) min.

12"

(30.5cm)

min. to grade

The maximum vent length for a corner installation is 24" (61cm).

24"

(61cm) min.

30 1/2"

(77.5cm)

2.2.1 periscope termination

2.2.2 corner termination

12"

(30.5cm)

min. to grade

EN

W415-2361 / A / 10.31.19

13

direct venting - model CDVS600-1

2.3 vent terminal clearances

Covered balcony applications ††*

Q

MIN

R

MAX

R

= 3 feet

(0.9m)

= 2 x

IHHW

(4.6m)

Q

ACTUAL

R

Q

S

G

P

INSTALLATIONS

CANADA U.S.A.

A

12” (30.5cm) 12” (30.5cm) Clearance above grade, veranda porch, deck or balcony.

B

12” (30.5cm)

Δ

9” (229mm)

Δ

Clearance to windows or doors that open.

C

12” (30.5cm)* 12” (30.5cm)* Clearance to permanently closed windows.

D

18”

(45.7cm)**

18”

(45.7cm)**

Vertical clearance to ventilated sofﬁ ts located above the terminal within a horizontal distance of 2’ (0.6m)

from the center line of the terminal.

E

12” (30.5cm)** 12” (30.5cm)** Clearance to unventilated sofﬁ t.

F

0” (0mm) 0” (0mm) Clearance to an outside corner wall.

G

0” (0mm)*** 0” (0mm)***

Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

2” (51mm)*** 2” (51mm)*** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

H

3’(0.9m) 3’(0.9m)****

Clearance to each side of the center line extended above the meter / regulator assembly to a maximum

vertical distance of 15’ (4.6m).

I

3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.

J

12” (30.5cm) 9” (229mm) Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.

K

6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.

L

7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.

M

12” (30.5cm)†† 12” (30.5cm)**** Clearance under a veranda, porch or deck.

N

16” (40.6cm) 16” (40.6cm) Clearance above the roof.

O

2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.

P

8’ (2.4m) 8’ (2.4m)

Roof must be non-combustible without openings.

Q

3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.

R

6’ (1.8m) 6’ (1.8m)

See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an opening

between the terminal and the open side of the structure.

S

12” (30.5cm) 12” (30.5cm) Clearance under a covered balcony

Δ The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad sofﬁ ts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements, check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the ﬂ oor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements, check local codes.

††* Permitted only if the balcony is fully open on a minimum of one side.

Clearances are to be in accordance with local

installation codes and the requirements of the gas

supplier. In their absence, clearances are to be as

listed above and are based on national codes.

note:

Wall terminals are for illustration purposes only. Size and

shapes may vary.

W415-2361 / A / 10.31.19

EN

14

direct venting - model CDVS600-1

2.4 venting application ﬂ ow chart

Top Exit

Horizontal Termination

Vertical rise is equal

to or greater than the

horizontal run

Vertical rise is equal

to or greater than the

horizontal run

Vertical rise is less

than horizontal run

Vertical rise is less

than horizontal run

Horizontal run +

vertical rise to

maximum of

24.75 feet (7.5m)

Horizontal run +

vertical rise to

maximum of

19 (5.8m)

4.2 times the vertical

rise equal to or

greater than the

horizontal run

3 times the vertical

rise equal to or

greater than the

horizontal run

Horizontal run +

vertical rise to

maximum of

40 feet (12.2m)

Horizontal run +

vertical rise to

maximum of

40 feet (12.2m)

Vertical Termination

REAR EXIT

Horizontal Termination

Vertical Termination

Vertical rise is equal

to or greater than

the horizontal run

Vertical rise is less

than horizontal run

Vertical rise is equal

to or greater than

the horizontal run

Vertical rise is less

than horizontal run

3.5 times the

vertical rise equal to

or greater than the

horizontal run

3 times the vertical

rise equal to or

greater than the

horizontal run

Horizontal run +

vertical rise to

maximum of

40 feet (12m)

Horizontal run +

vertical rise to

maximum of

24.75 feet (7.5m).

Horizontal run +

vertical rise to

maximum of

40 feet (12m)

Horizontal run +

vertical rise to

maximum of

40 feet (12m)

EN

W415-2361 / A / 10.31.19

15

direct venting - model CDVS600-1

2.5 deﬁ nitions

2.6 elbow vent length values

For the following symbols used in the venting calculations and

examples are:

> - greater than

> - equal to or greater than

< - less than

< - equal to or less than

H

T

- total of both horizontal vent lengths (Hr) and offsets (Ho) in feet

H

R

- combined horizontal vent lengths in feet

H

O

- offset factor: .03 (total degrees of offset - 90°*) in feet

H

O

- offset factor: .03 (total degrees of offset - 135°*) in feet

V

T

- combined vertical vent lengths in feet

Feet Inches Millimeters

1° 0.03 0.5 12.7

15° 0.45 6.0 152.4

30° 0.9 11.0 279.4

45° 1.35 16.0 406.4

90°* 2.7 32.0 812.8

* The ﬁ rst 90° offset has a zero value and is shown in the formula as - 90°

* The ﬁ rst 45° and° offset have a zero value and is shown in the formula as -45° and -90° respectively

or -135° when combined (for 45° exit only).

W415-2361 / A / 10.31.19

EN

16

direct venting - model CDVS600-1

(H

T

) > (V

T

)

Simple venting conﬁguration (only one 90° elbow)

See graph to determine the required vertical rise V

T

for

the required horizontal run H

T

.

REQUIRED

VERTICAL RISE IN

FEET (METERS) V

T

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERES) H

T

For vent conﬁgurations requiring more than one 90° elbow, the following formulas apply:

Formula 1: H

T

< 4.2 V

T

Formula 2: H

T

+ V

T

< 24.75 feet (7.5m)

Example:

V

1

= V

T

= 6 FT (1.8m)

H

1

= 3 FT (0.9m)

H

2

= 5 FT (1.5m)

H

R

= H

1

+ H

2

= 3FT (0.9m) + 5FT (1.5m) = 8 FT (2.4m)

H

O

= .03 (two 90° elbows - 90°) = .03 (180° - 90°) = 2.7FT (0.8m)

H

T

= H

R

+ H

O

= 8FT (2.4m) + 2.7FT (0.8m) = 10.7FT (3.3m)

H

T

+ V

T

= 10.7FT (3.3m) + 6FT (1.8m) = 16.7FT (5.1m)

Formula 1: H

T

< 4.2 V

T

4.2 V

T

= 4.2FT (1.3m) x 6FT (1.8m) = 25.2FT (7.7m)

10.7FT (3.3m) < 25.2FT (7.7m)

Formula 2: H

T

+ V

T

< 24.75 FT (7.5m)

16.7FT (5.1m) < 24.75 (7.5m)

Since both formulas are met, this vent conﬁguration is acceptable.

0

5

(1.5)

15

(4.6)

20 (6.1)

8.3 (2.5)

4.2 (1.3)

12.5

(3.8)

1.6 (5)

4.8 (1.5)

12.3 (3.8)

2

(0.6)

The shaded area within the lines represents acceptable

values for H

T

and V

T

90°

V

1

H

1

H

2

90°

Example:

V

1

= 4 FT (1.2m)

V

2

= 1.5 FT (0.5m)

V

T

= V

1

+ V

2

= 4FT (1.2m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

H

1

= 2 FT (0.6m)

H

2

= 1 FT (0.3m)

H

3

= 1 FT (0.3m)

H

4

= 1.5 FT (0.5m)

H

R

= H

1

+ H

2

+ H

3

+ H

4

= 2FT (0.6m) + 1FT (0.3m) + 1FT (0.3m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

H

O

= .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT (2.5m)

H

T

= H

R

+ H

O

= 5.5 FT (1.7m) + 8.1 FT (2.5m) = 13.6 FT (4.2m)

H

T

+ V

T

= 13.6 FT (4.2m) + 5.5 FT (1.7m) = 19.1 FT (5.8m)

Formula 1: H

T

< 4.2 V

T

4.2 V

T

= 4.2 FT (1.3m) x 5.5 FT(1.7m) = 23.1 FT (7m)

13.6 FT (4.2m) < 23.1 FT (7m)

Formula 2: H

T

+ V

T

< 24.75 FT (7.5m)

19.1FT (5.8m) < 24.75 FT (7.5m)

Since both formulas are met, this vent conﬁ

g

uration is acceptable.

90°

H

1

H

2

V

1

V

2

H

3

H

4

10

(3.1)

19.5

(5.9)

2.7 top exit horizontal termination

0

5

(1.5)

15

(4.6)

20 (6.1)

100 (2540)

50 (1270)

150 (3810)

12.5

(3.8)

29 (737)

57 (1447.8)

147

(3733.8)

2

(0.6)

10

(3.1)

19.5

(5.9)

INCHES (MILLIMETERS)

EN

W415-2361 / A / 10.31.19

17

direct venting - model CDVS600-1

2.8 top exit horizontal termination

(H

T

) ≤ (V

T

)

Simple venting conﬁguration (only one 90° elbow)

See graph to determine the required vertical rise V

T

for

the required horizontal run H

T

.

Required vertical

rise in feet

(meters) V

T

Horizontal vent run plus offset in feet (meters) H

T

For vent conﬁgurations requiring more than one 90° elbow, the following formulas apply:

Formula 1: H

T

< V

T

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

Example:

V

1

= 3 ft (0.9m)

V

2

= 8 ft (2.4m)

V

T

= V

1

+ V

2

= 3 ft (0.9m) + 8 ft (2.4m) = 11 ft (3.4m)

H

1

= 2.5 ft (0.8m)

H

2

= 2 ft (0.6m)

H

R

= H

1

+ H

2

= 2.5ft (0.8m) + 2 ft (0.6m) = 4.5 ft (1.4m)

H

O

= .03 (two 90° elbows - 90°) = .03 (180° - 90°) = 5.4 ft (1.7m)

H

T

= H

R

+ H

O

= 4.5 ft (1.4m) + 5.4 ft (1.6m) = 9.9 ft (3m)

H

T

+ V

T

= 9.9 ft (3m) + 11 ft (3.4m) = 20.9 ft (6.4m)

Formula 1: H

T

< V

T

9.9 ft (3m) < 11 ft (3.4m)

Formula 2: H

T

+ V

T

< 40 ft (12.2m)

20.9 ft (6.4m) < 40 ft (12.2m)

Since both formulas are met, this vent conﬁguration is acceptable.

The shaded area within the lines represents acceptable

values for H

T

and V

T

0

2.5

(0.8)

5

(1.5)

7.5

(2.3)

10

(3.1)

12.5

(3.8)

15

(4.6)

40 (12.2)

10 (3.1)

20 (6.1)

30 (9.1)

17.5

(5.3)

20

(6.1)

39 (11.9)

90°

V

1

V

2

H

1

H

2

W415-2361 / A / 10.31.19

EN

18

direct venting - model CDVS600-1

0

2.5

(0.8)

5

(1.5)

7.5

(2.3)

10

(3.1)

12.5

(3.8)

15

(4.6)

40 (12.2)

10 (3.1)

20 (6.1)

30 (9.1)

17.5

(5.3)

20

(6.1)

1.6

(0.5)

1.6 (0.5)

38.3 (11.7)

90°

V

1

V

2

H

1

H

2

90°

H

3

Simple venting conﬁguration

(only two 90° elbows)

See graph to determine the required vertical rise V

T

for the required

horizontal run H

T

.

REQUIRED

VERTICAL

RISE IN FEET

(METERS) V

T

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

T

The shaded area within the lines represents acceptable values for H

T

and H

T

(H

T

) < (V

T

)

For vent conﬁgurations requiring more than two 90° elbows, the following formulas apply:

Formula 1: H

T

< V

T

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

Example:

V

1

= 9 FT (2.7m)

V

2

= 6 FT (1.8m)

V

T

= V

1

+ V

2

= 9FT (2.7m) + 6FT (1.8m) = 15FT (4.6m)

H

1

= 3 FT (0.9m)

H

2

= 2 FT (0.6m)

H

3

= 1.5 FT (0.5m)

H

R

= H

1

+ H

2

+ H

3

= 3FT (0.9m) + 2FT (0.6m) + 1.5FT (0.5m) = 6.5FT (2m)

H

O

= .03 (four 90° elbows - 90°) = .03 (360° - 90°) = 8.1 FT (2.5m)

H

T

= H

R

+ H

O

= 6.5FT (2m) + 8.1FT (2.5m) = 14.6FT (4.5m)

H

T

+ V

T

= 14.6FT (4.5m) + 15FT (4.6m) = 29.6 FT (9m)

Formula 1: H

T

< V

T

14.6 FT (4.5m) < 15 FT (4.6m)

Formula 2: H

T

+ V

T

< 40 FT (12.2m)

29.6 FT (9m) < 40 FT (12.2m)

Since both formulas are met, this vent conﬁguration is acceptable.

2.9 rear exit horizontal termination

0

2.5

(0.8)

5

(1.5)

7.5

(2.3)

10

(3.1)

12.5

(3.8)

15

(4.6)

40 (12.2)

10 (3.1)

20 (6.1)

30 (9.1)

17.5

(5.3)

20

(6.1)

1.6

(0.5)

2 (0.6)

38.3 (11.7)

EN

W415-2361 / A / 10.31.19

19

direct venting - model CDVS600-1

Simple venting conﬁguration

(only two 90° elbows)

See graph to determine the required vertical rise V

T

for the

required horizontal run H

T

.

REQUIRED

VERTICAL RISE IN

FEET (METERS)V

T

HORIZONTAL VENT RUN PLUS OFFSET IN FEET (METERS) H

T

The shaded area within the lines represents acceptable

values for H

T

and H

T

(H

T

) > (V

T

)

0

2.5

(0.8)

5 (1.5) 7.5

(2.3)

10

(3.1)

12.5

(3.8)

15

(4.6)

17.5

(5.3)

20

(6.1)

1 (0.3)

5.5 (1.2)

1

(0.3)

3.5

(1.1)

19.25

(5.9)

For vent conﬁgurations requiring more than two 90° elbows, the following formulas apply:

Formula 1: H

T

< 3.5V

T

Formula 2: H

T

+ V

T

< 24.75 feet (7.5m)

Example:

V

1

= 4 FT (1.2m)

V

2

= 1.5 FT (0.5m)

V

T

= V

1

+ V

2

= 4FT (1.2m) + 1.5FT (0.5m) = 5.5 FT (1.7m)

H

1

= 2 FT (0.6m)

H

2

= 1 FT (0.3m)

H

3

= 1 FT (0.3m)

H

4

= 1.5 FT (0.5m)

H

R

= H

1

+ H

2

+H

3

+H

4

= 2FT(0.6m) + 1FT(0.3m) + 1FT(0.3m) + 1.5FT(0.5m) = 5.5 FT(1.7m)

H

O

= .03 (four 90° elbows + one 45° elbow - 90°)

= .03 (90 + 90 + 90 + 90 + 45 - 90) = 9.45 FT (2.9m)

H

T

= H

R

+ H

O

= 5.5FT (1.7m) + 9.45FT (2.9m) = 14.95FT (4.6m)

H

T

+ V

T

= 14.95FT (4.6m) + 5.5FT (1.7m) = 20.45FT (6.2m)

Formula 1: H

T

< 3.5V

T

3.5V

T

= 3.5FT (1.1m) x 5.5FT (1.7m) = 19.25FT (5.9m)

14.95 FT (4.6m) < 19.25 FT (5.9m)

Formula 2: H

T

+ V

T

< 24.75 FT (7.5m)

20.45 FT (6.2m) < 24.75 FT (7.5m)

Since both formulas are met, this vent conﬁguration is acceptable.

90°

V

1

V

2

H

1

H

2

90°

H

3

8.3 (2.5)

12.3 (3.8)

4.2 (1.3)

50 (1270)

100 (2540)

150(3810)

0

2.5

(0.8)

5

(1.5)

7.5

(2.3)

10

(3.1)

12.5

(3.8)

15

(4.6)

17.5

(5.3)

20

(6.1)

147 (3733.8

24

(610)

66

(1676.4)

1

(0.3)

3.5

(1.1)

19.25

(5.9)

INCHES (MILLIMETERS)

W415-2361 / A / 10.31.19

EN

20

direct venting - model CDVS600-1

2.10 top or rear exit vertical termination

Simple venting conﬁgurations.

See graph to determine the required vertical rise V

T

for the

required horizontal run H

T

.

REQUIRED

VERTICAL RISE IN

FEET (METERS)V

T

HORIZONTAL VENT RUN PLUS OFFSET IN FEET

(METERS) H

T

The shaded area within the lines represents acceptable

values for H

T

and H

T

0

5 (1.5) 10

(3.1)

15 (4.6) 20

(6.1)

40 (12.2)

10 (3.1)

20 (6.1)

30 (9.1)

3 (0.9)

(H

T

) < (V

T

)

For vent conﬁgurations requiring one or more 90° elbows (top exit) or one or more 90° elbows

(rear exit), the following formulas apply:

Formula 1: H

T

< V

T

Formula 2: H

T

+ V

T

< 40 feet (12.2m)

Example:

V

1

= 5 FT (1.5m)

V

2

= 6 FT (1.8m)

V

3

= 10 FT (3.1m)

V

T

= V

1

+ V

2

+ V

3

= 5FT (1.5m) + 6FT (1.8m) + 10FT (3.1m) = 21 FT (6.4m)

H

1

= 8 FT (2.4m)

H

2

= 2.5 FT (0.8m)

H

R

= H

1

+ H

2

= 8FT (2.4m) + 2.5FT (0.8m) = 10.5FT (3.2m)

H

O

= .03 (four 90° elbows - 90°)

= .03 (360° - 90°) = 8.1 FT (2.5m)

H

T

= H

R

+ H

O

= 10.5FT (3.2m) + 8.1FT (2.5m) = 18.6FT (5.7m)

H

T

+ V

T

= 18.6FT (5.7m) + 21FT (6.4m) = 39.6FT (12.1m)

Formula 1: H

T

< 3.5V

T

18.6 FT (5.7m) < 21 FT (6.4m)

Formula 2: H

T

+ V

T

< 40 FT (12.2m)

39.6FT (12.1m) < 40 FT (12.2m)

Since both formulas are met, this vent conﬁguration is acceptable.

La page charge ...

Continental Fireplaces CDVS600-1NSB Le manuel du propriétaire

Continental Fireplaces CDVS600-1NSB Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents