NAPOLEON LVX62N2X Manuel utilisateur

FRENCH

PG. 95

W415-2035 / C / 04.30.21

ADD MANUAL TITLE

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.napoleon.com • [email protected]

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

NATURAL GAS MODELS:

PROPANE GAS MODELS:

Product Name / Code

(MUST use title from Price Book)

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

CSA /

INTERTEK

LOGO

SAFETY INFORMATION

- Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity of

this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the ﬁ re department.

- Installation and service must be

performed by a qualiﬁ ed installer, service

agency, or the supplier.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certiﬁ ed kit is used.

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

WARNING

!

ENGLISH

$10.00

FOR INDOOR USE ONLY

IF INSTALLATION + OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

INSTALLATION MANUAL

LVX38N-1 / LVX50N-1 / LVX62N-1 / LVX74N-1 / LVX38N2-1 / LVX50N2-1 / LVX62N2-1 / LVX74N2-1

LVX38P-1 / LVX50P-1 / LVX62P-1 / LVX74P-1 / LVX38P2-1 / LVX50P2-1 / LVX62P2-1 / LVX74P2-1

Luxuria™ Series

(LVX38-1 illustrated)

GLASS GUARD

THIS APPLIANCE IS INSTALLED WITH

CERTIFIED TO THE CANADIAN AND AMERICAN NATIONAL STANDARDS:

CSA 2.22 AND ANSI Z21.50 FOR VENTED DECORATIVE GAS APPLIANCES

FOR INDOOR USE ONLY

PLACE BARCODE LABEL ON THE

OWNER’S MANUAL

W415-2035 / C / 04.30.21

EN

2

safety information

• This appliance is hot when operated and

can cause severe burns if contacted.

• Any changes or alterations to this

appliance or its controls can be

dangerous and is prohibited.

• Do not operate appliance before reading and

understanding operating instructions. Failure

to operate appliance according to operating

instructions could cause ﬁ re or injury.

• Ensure the glass door is opened or removed

when lighting the pilot for the ﬁ rst time and

when the gas supply has run out.

• Risk of ﬁ re or asphyxiation, do not operate

appliance with ﬁ xed glass removed and never

obstruct the front opening of the appliance.

• Do not connect 110 volts to the control valve,

with the exception of models; GSST8 and

GT8.

• Risk of burns. The appliance should be turned off and cooled before servicing.

• Do not install damaged, incomplete or substitute components.

• Risk of cuts and abrasions. Wear protective gloves, protective footwear, and safety glasses during

installation. Sheet metal edges may be sharp.

• Do not burn wood or other materials in this appliance.

• Provide adequate ventilation and combustion air. Provide adequate accessibility clearance for servicing

and operating the appliance.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at

test pressures above 1/2 psig. Close the manual shut-off valve before pressure testing gas line at test

pressures equal to or less than 1/2 psig (35mb).

• The appliance must not be operated at temperatures below freezing (32°F / 0°C). Allow the appliance

to warm to above freezing prior to operation, with the exception of models; GSS36, GSS42; these

appliances are suitable for 0°F / -18°C.

• Children and adults should be alerted to hazards of high surface temperature and should stay

away to avoid burns or clothing ignition.

• Young children should be carefully supervised when they are in the same room as the

appliance. Toddlers, young children and others may be susceptible to accidental contact

burns. A physical barrier is recommended if there are at risk individuals in the house. To

restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers,

young children and other at risk individuals out of the room and away from hot surfaces.

• Clothing or other ﬂ ammable material should not be placed on or near the appliance.

• Due to high temperatures, the appliance should be located out of trafﬁ c and away from

furniture and draperies.

• Furniture or other objects must be kept a minimum of 4 feet (1.22m) away from the front of the appliance.

• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot

surfaces.

• Even after the appliance is off, it will remain hot for an extended period of time.

• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children

from hot surfaces. These screens and guards must be fastened to the ﬂ oor.

• Any safety screen, guard or barrier removed for servicing the appliance, must be replaced prior

to operating the appliance.

• It is imperative that the control compartments, burners and circulating blower and its passageway in the

appliance and venting system are kept clean. The appliance and its venting system should be inspected

before use and at least annually by a qualiﬁ ed service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and

free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• If the appliance shuts off, do not re-light until you provide fresh air. If appliance keeps shutting off, have it

serviced. Keep burner and control compartment clean.

• Under no circumstances should this appliance be modiﬁ ed.

• Do not allow wind or fans to blow directly into the appliance. Avoid any drafts that alter burner ﬂ ame

patterns.

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

!

DANGER

A barrier designed to reduce the risk of burns from the hot

viewing glass is provided with this appliance and must be

installed for the protection of children and other at-risk

individuals.

!

WARNING

EN

W415-2035 / C / 04.30.21

3

safety information

!

WARNING

• Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this

appliance.

• This appliance must not be connected to a chimney ﬂ ue pipe serving a separate solid fuel burning

appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualiﬁ ed service technician

to inspect the appliance and to replace any part of the control system and any gas control which has

been under water.

• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass

should be done by a licensed or qualiﬁ ed service person, if equipped.

• Do not strike or slam shut the appliance glass door, if equipped.

• Only doors / optional fronts certiﬁ ed with the appliance are to be installed on the appliance.

• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As

with all plastic bags, these are not toys and should be kept away from children and infants.

• Carbon or soot should not occur in a vent free appliance as it can distribute into the living area of your

home. If you notice any signs of carbon or soot, immediately turn off your appliance and arrange to have

it serviced by a qualiﬁ ed technician before operating it again.

• If equipped, the screen must be in place (closed) when the appliance is in operation.

• When equipped with pressure relief doors, they must be kept closed while the appliance is operating

to prevent exhaust fumes containing carbon monoxide, from entering into the home. Temperatures of

the exhaust escaping through these openings can also cause the surrounding combustible materials to

overheat and catch ﬁ re.

• Carbon monoxide poisoning may lead to death; early signs of carbon monoxide poisoning resemble the

ﬂ u, with headache, dizziness and/or nausea. If you have these signs, the appliance may not be working

properly. Get fresh air at once! Have appliance serviced. Some people; pregnant women, persons with

heart or lung disease, anemia, those under the inﬂ uence of alcohol, those at high altitudes are more

affected by carbon monoxide than others. Failure to keep the primary air opening(s) of the burner(s) clean

may result in sooting and property damage.

• As with any combustion appliance, we recommend having your appliance regularly inspected and

serviced as well as having a Carbon Monoxide Detector installed in the same area to defend you and

your family against Carbon Monoxide (not applicable for outdoor appliances).

• Ensure clearances to combustibles are maintained when building a mantel or shelves above the

appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting,

discolouration or damage to decorations, a TV or other electronic components.

• For appliances equipped with a safety barrier; if the barrier becomes damaged, the barrier

shall be replaced with the manufacturer’s barrier for this appliance.

• Installation and repair should be done by a qualiﬁ ed service person. It is imperative that control

compartments, burners and circulating air passageways of the appliance be kept clean.

• For outdoor products only: this appliance must not be installed indoors or within any structure that

prevents or inhibits the exhaust gases from dissipating in the outside atmosphere.

• If applicable, the millivolt version of this appliance uses and requires a fast acting thermocouple. Replace

only with a fast acting thermocouple supplied by Wolf Steel Ltd.

!

WARNING

!

Disconnect the appliance main gas valve/control

from the supply piping when pressure testing that

system at pressures in excess of 1/2 psi (3.5 kPa).

Isolate the appliance with it’s shut off valve during

any pressure testing of the supply piping at

pressures equal to or less than 1/2 psi (3.5 kPa).

FIRE RISK HAZARD / DELAYED IGNITION

High supply pressure will damage the valve / controls.

Add California Prop 65 warning

!

WARNING:

This product can expose you to chemicals including lead and lead compounds,

which are known to the State of California to cause cancer, and chemicals including carbon

monoxide, which are known to the State of California to cause birth defects or other reproduc-

tive harm. For more information, go to www.P65Warnings.ca.gov.

W415-2035 / C / 04.30.21

EN

4

table of contents

1.0 general information 5

1.1 rates and efﬁ ciencies 6

1.2 installation checklist 7

1.3 installation overview 8

1.4 Dynamic Heat Control™ 9

1.5 rating plate/lighting instruction location

11

1.6 mobile home installation 12

1.7 hardware list 12

1.8 lifting handles installation/removal 12

2.0 dimensions 13

2.1 single-sided 13

2.2 see-thru 14

3.0 minimum venting requirements 15

3.1 typical venting installation 17

3.2 minimum air terminal location

clearances 19

3.3 horizontal termination 20

3.4 vertical termination 23

3.5 LVX38-1 venting conﬁ gurations 24

3.6 LVX50-1 / LVX62-1 venting

conﬁ gurations 25

3.7 LVX74-1 venting conﬁ gurations 26

4.0 installation planning 27

4.1 installation option 1 - open enclosure

(enclosure stops short of the ceiling) 29

4.2 installation option 2 - front opening 30

4.3 installation option 3 - Rear Opening 31

4.4 installation option 4 - open enclosure

with hard combustible valance 32

5.0 rough framing - before appliance

installation 33

5.1 minimum framing dimensions 34

5.1.1 minimum clearance to combustible

enclosures 35

6.0 venting installation 38

6.1 ﬁ restop spacer assembly 38

6.2 horizontal installation 40

6.3 vertical installation 40

6.4 using ﬂ exible vent components 41

6.4.1 horizontal air terminal installation 41

6.5 vertical air terminal installation 42

6.5.1 appliance vent connection 42

6.6 restricting vertical vents 43

6.6.1 LVX38-1 / LVX50-1 43

6.6.2 LVX62-1 / LVX74-1 43

6.7 vent shield installation 44

7.0 electrical information 45

7.1 hard wiring connection 45

7.2 receptacle wiring diagram 45

7.3 in the event of a power failure 45

7.4 battery holder/switch installation 46

7.5 initializing the battery holder/switch for

the ﬁ rst time 46

7.6 wiring diagram 47

7.7 eFire controller application 47

7.7.1 LVX38-1/ LVX50-1 wiring diagram 48

7.7.2 LVX62-1/ LVX74-1 wiring diagram 49

7.8 access panel 50

8.0 gas installation 51

9.0 operation 52

9.1 pilot-on-demand 53

10.0 nailing tab installation 54

11.0 finish framing

- after appliance installation

55

11.1 framing with Dynamic Heat Control™

55

12.0 finishing 60

12.1 fastener placement restriction 60

12.2 enclosure design 61

12.3 ﬁ nishing with combustibles 62

12.4 minimum combustible mantel

clearances 64

12.5 optional trim ﬁ nishing 65

12.6 glass guard installation / removal 66

12.7 ﬁ rebox glass door installation /

removal 75

12.8 media tray removal 76

12.9 media installation / removal 77

13.0 adjustments 78

13.1 restricting vertical vents 78

13.2 venturi adjustment 78

13.3 pilot burner adjustment 79

13.4 ﬂ ame characteristics 79

14.0 maintenance 80

14.1 annual maintenance 81

14.2 control access 81

14.3 burner removal 82

14.4 valve removal 82

14.5 control module removal 83

14.6 LED replacement 84

14.7 glass / door replacement 85

14.8 care of glass 85

14.9 care of plated parts 85

15.0 replacement parts 86

15.1 overview 87

15.2 burner components 88

16.0 troubleshooting 90

17.0 warranty 93

The information throughout this manual is believed to be correct at the time of printing. Wolf Steel

Ltd. reserves the right to change or modify any information within this manual at any time without

notice. Changes, other than editorial are denoted by a vertical line in the margin.

note:

EN

W415-2035 / C / 04.30.21

5

general information

Installer: please ﬁ ll out appliance checklist in the

owner’s manual.

When the appliance is installed at elevations above 4,500ft (1372m), and in the absence of speciﬁ c recommendations

from the local authority having jurisdiction, the certiﬁ ed high altitude input rating shall be reduced at the rate of 4% for each

additional 1,000ft (305m). Expansion / contraction noises during heating up and cooling down cycles are normal

and are to be expected. Change in ﬂ ame appearance from “HI” to “LO” is more evident in natural gas than in

propane.

This appliance is approved for bathroom, bedroom and bed-sitting room installations and is certiﬁ ed for mobile

home installation.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certiﬁ ed kit is used.

There is a switch that controls the function of the appliance. The battery holder/switch must be placed in the

middle position. If the switch is not placed in the middle position, the appliance will not work.

The protective wrap on plated parts is best removed when the assembly is at room temperature but this can

be improved if the assembly is warmed, using a hair dryer or similar heat source. The protective wrap must be

removed before operating the appliance.

This appliance is a decorative product. It is not a source of heat and not intended to burn solid fuel.

This appliance is equipped with a remote control and a wall switch, which requires batteries to be installed. The

remote takes 3 “AAA” batteries and the wall switch takes 4 “AA” batteries.

note:

Batteries must be disposed of according to the local laws and regulations. Some batteries may be

recycled, and may be accepted for disposal at your local recycling center. Check with your

municipality for recycling instructions.

A glass guard assembly designed to reduce the risk of burns is provided with the appliance and must

be installed. Never operate the appliance without the complete Glass Guard Barrier System installed

and closed.

1.0 general information

important:

Some components and/or media are packaged separately and must be installed in accordance with the

information in this manual.

W415-2035 / C / 04.30.21

EN

6

general information

Single-Sided See-thru

Appliance Type LVX38N-1 LVX38P-1 LVX38N2-1 LVX38P2-1

Fuel Type Natural Gas Propane Natural Gas Propane

Altitude (FT) 0-4,500

Max. Input (BTU/HR) 31,000 26,500 31,000 26,500

Min. Input (BTU/HR) 22,000

Single-Sided See-thru

Appliance Type LVX50N-1 LVX50P-1 LVX50N2-1 LVX50P2-1

Fuel Type Natural Gas Propane Natural Gas Propane

Altitude (FT) 0-4,500

Max. Input (BTU/HR) 38,000 31,500 38,000 31,500

Min. Input (BTU/HR) 26,000 25,000 26,000 25,000

Single-Sided See-thru

Appliance Type LVX62N-1 LVX62P-1 LVX62N2-1 LVX62P2-1

Fuel Type Natural Gas Propane Natural Gas Propane

Altitude (FT) 0-4,500

Max. Input (BTU/HR) 44,000 35,000 44,000 35,000

Min. Input (BTU/HR) 32,000 28,000 32,000 28,000

LVX50-1

1.1 rates and efﬁ ciencies

Single-Sided See-thru

Appliance Type LVX74N-1 LVX74P-1 LVX74N2-1 LVX74P2-1

Fuel Type Natural Gas Propane Natural Gas Propane

Altitude (FT) 0-4,500

Max. Input (BTU/HR) 50,000 41,500 50,000 41,500

Min. Input (BTU/HR) 35,000 33,0000 35,000 33,000

LVX38-1

LVX62-1

LVX74-1

Natural Gas Propane

Min. Inlet Gas Supply

Pressure

4.5" w.c. (11mb) 11" w.c. (27mb) 4.5" w.c. (11mb) 11" w.c. (27mb)

Max. Inlet Gas Supply

Pressure

7"* w.c. (17mb) 13” w.c. (32mb) 13” w.c. (32mb) 13” w.c. (32mb).

Manifold Pressure (Under

Flow Conditions)

3.5” w.c. (9mb) 10” w.c. (25mb) 3.5 w.c. (9mb) 10” w.c. (25mb)

LVX38-1 / LVX50-1 / LVX62-1 / LVX74-1

*Maximum inlet pressure not to exceed 13” w.c. (32mb).

EN

W415-2035 / C / 04.30.21

7

general information

1.2 installation checklist

GAS FIREPLACE INSTALLATION CHECKLIST

Customer:

Date Installed:

Address: Installer:

Model: Dealer:

Serial #: Dealer Phone #:

This checklist is a reference tool only. It is not intended as a substitute for the installation instructions.

Wolf Steel Ltd. recommends photographs of the various stages of construction be filed along with a copy of this completed form.

Fireplace Installation

Is the fireplace level and secured?

YES IF NOT, PLEASE EXPLAIN WHY?

Are the factory supplied non-combustible materials installed?

Is the exterior wall insulated and dry-walled?

Are the clearances to combustibles maintained?

Are the logs/media installed as instructed?

Are the accessories installed as instructed?

Is the glass door properly sealed and unobstructed?

Is the safety barrier installed and secure?

Are all required accessories installed (i.e. door trims)?

Venting Installation

Is the venting configuration within the parameters?

Has the venting been sealed with the appropriate sealant?

Is the venting supported and secured?

Are all clearances to combustibles maintained?

Are the appropriate firestops and shields properly installed?

Is the terminal, level, secured and sealed?

Gas and Electrical

Was the fireplace converted to propane?

Was the appropriate supply pressure verified?

Were all gas connections leak tested?

Is the 110 VAC supply connection to the fireplace compliant?

Are all electrical wires protected from damage?

Finishing

Non-combustible materials used as per instructions?

Enclosure instructions forwarded to builder/finisher?

Minimum enclosure dimensions compliant?

Combustible Mantle Clearances compliant?

Commissioning

Was the fireplace test fired and all operation verified?

Safety and lighting instructions reviewed with the Customer?

Operating Instruction Manual left with the Customer?

W415-2035 / C / 04.30.21

EN

8

general information

general

information

14

10

13

6

5

8

9

4

3

2

GLASS GUARD

1.3 installation overview

Recommended installation steps:

1. Determine venting requirements before deciding the ﬁ nal location of the appliance

2. Plan out appliance enclosure, framing, fronts, accessories, etc.

3. Install rough framing (refer to “rough framing” section)

4. Place the appliance in its ﬁ nal position

5. Install nailing tabs (refer to “nailing tab installation” section)

6. Install appliance venting (refer to “venting installation” section)

7. Install vent shield (refer to “vent shield installation” section)

8. Install all electrical wirings (refer to “electrical information” section)

9. Install gas lines (refer to “gas installation” section)

10. Fit glass guard (refer to “glass guard assembly installation / removal” section)

11. Test appliance (Glass Guard must be installed while testing the appliance)

12. Remove and protect glass guard. Take great care to store using original packaging.

13. Complete framing (refer to “ﬁ nish framing” section)

14. Finishing (refer to “ﬁ nishing” section)

15. If necessary, do ﬁ nal adjustments to glass guard.

16. Complete installation checklist in the owner’s manual and apply the serial number to owner’s manual

EN

W415-2035 / C / 04.30.21

9

general information

1.4 Dynamic Heat Control™

Dynamic Heat Control™ is a system for managing the

heat produced by the appliance at and around the ﬁ re-

place. The purpose of the Dynamic Heat Control™ is

to move the heat away from the ﬁ replace to allow it to cir-

culate more effectively within the living space. By install-

ing the Dynamic Heat Control™ both the installer and

the user gain considerable beneﬁ ts, see the following;

Installer:

• Ability to use combustible framing and ﬁ nishing right up to the ﬁ replace opening.

*

• High temperatures above the front of the ﬁ replace opening are signiﬁ cantly reduced eliminating potential de-

grading to sensitive ﬁ nish material (cracks or discoloration).

• No additional electricals, fans, ducts, or manifolds are required which keeps installation straightforward.

User:

• Heat is circulated more consistently throughout the living space increasing comfort in front of the ﬁ replace.

• Increased “real world” efﬁ ciency as heat is moved in to the room rather than retained inside an enclosure.

• Complete ﬂ exibility in selection of ﬁ nish materials.

• Ability to place a TV, sound bar or artwork above the ﬁ replace.**

The Dynamic Heat Control™ system relies on an optimized ﬂ ow of air both through the appliance and the en-

closure. As such the installation of the Dynamic Heat Control™ system requires certain technical considerations

when compared to traditional ﬁ replaces. Speciﬁ cally, the Dynamic Heat Control™ requires the enclosure to be

ventilated and requires the installer to ensure that a minimum opening area is provided to allow heat to escape

and circulate at a prescribed minimum height and position. This must be carefully adhered to in the planning and

the installation to ensure the appliance functions safely and to minimize installation time.

*In most common installation conﬁ gurations, some speciﬁ c installations require special provisions.

See “framing with Dynamic Heat Control™ section for details. Ensure to strictly adhere to instructions.

** Always check the appliance manufacturer’s recommendations to conﬁ rm suitability and any special

environmental limitations. For valuable or antique items, always refer to expert preservation instruc-

tions as some items require speciﬁ cally controlled temperature and/or humidity

PATENT PENDING

W415-2035 / C / 04.30.21

EN

10

general information

!

WARNING

• Always light the pilot whether for the ﬁ rst time or if the gas supply has run out, with the glass door opened

or removed.

• Provide adequate clearance for servicing and operating the appliance.

• Provide adequate ventilation.

• Never obstruct the front opening of the appliance.

• Objects placed in front of the appliance must be kept a minimum of 48” (121.9cm) from the front face of

the appliance.

• Surfaces around and especially above the appliance can become hot. Avoid contact when appliance is

operating.

• Fire risk. Explosion hazard.

• High pressure will damage valve. Disconnect gas supply piping before pressure testing gas line at test

pressures above 1/2 PSIG. Close the manual shut-off valve before pressure testing gas line at test

pressures equal to or less than 1/2 PSIG (35mb).

• Use only Wolf Steel approved optional accessories and replacement parts with this appliance using non-

listed accessories (blowers, doors, louvres, trims, gas components, venting components, etc.) could result

in a safety hazard and will void the warranty and certiﬁ cation.

• The appliance must not be operated at temperatures below freezing (32ºF / 0ºC). Allow the appliance to

warm to above freezing prior to operation.

• This appliance has been designed and certiﬁ ed for indoor use only.

THIS GAS APPLIANCE MUST BE INSTALLED AND SERVICED BY A QUALIFIED INSTALLER to conform with local

codes. Installation practices vary from region to region and it is important to know the speciﬁ cs that apply to your area, for

example in the state of Massachusetts:

• This product must be installed by a licensed plumber or gas ﬁ tter when installed within the commonwealth of

Massachusetts.

• The appliance damper must be removed or welded in the open position prior to installation of an appliance insert or gas

log.

• The appliance off valve must be a “T” handle gas cock.

• The ﬂ exible connector must not be longer than 36 inches (0.9m).

• A carbon monoxide detector is required in all rooms containing gas ﬁ red appliances.

• The appliance is not approved for installation in a bedroom or bathroom unless the unit is a direct vent sealed

combustion product.

The installation must conform with local codes or, in absence of local

codes, the National Gas and Propane Installation Code CSA B149.1

in Canada, or the National Fuel Gas Code, ANSI Z223.1 / NFPA 54

in the United States. Suitable for mobile home installation if installed

in accordance with the current standard CAN/CSA Z240MH Series,

for gas equipped mobile homes, in Canada or ANSI Z223.1 and

NFPA 54 in the United States.

The appliance and its individual shutoff valve must be disconnected

from the gas supply piping system during any pressure testing

of that system at test pressures in excess of 1/2 psig (35 mb).

The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any

pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (35 mb). When installed

with a blower or fan, the junction box must be electrically connected and grounded in accordance with local codes. In the

absence of local codes, use the current CSA C22.1 Canadian Electrical Code in Canada or the ANSI / NFPA 70 National

Electric Code in the United States. In the case where the blower is equipped with a power cord, it must be connected into a

properly grounded receptacle. The grounding prong must not be removed from the cord plug.

The following does not apply to inserts; as long as the required clearance to combustibles is maintained, the most desirable

and beneﬁ cial location for an appliance is in the center of a building, thereby allowing the most efﬁ cient use of the heat

created. The location of windows, doors and, the trafﬁ c ﬂ ow in the room where the appliance is to be located should be

considered. If possible, you should choose a location where the vent will pass through the house without cutting a ﬂ oor or

roof joist. If the appliance is installed directly on carpeting, vinyl tile or other combustible material other than wood ﬂ ooring, the

appliance shall be installed on a metal or wood panel extending the full width and depth, unless otherwise tested.

We suggest that our gas

hearth products be installed

and serviced by professionals

who are certied in the U.S.

by the National Fireplace

Institute

®

(NFI) as NFI Gas

Specialists

www.ncertied.org

EN

W415-2035 / C / 04.30.21

11

general information

CERTIFIED UNDER / HOMOLOGUE SELON LES NORMES: CSA 2.33

b

- 2008, ANSI Z21.88

b

- 2008 VENTED GAS FIREPLACE HEATER / APPAREIL DE CHAUFFAGE ALIMENTÉ

AU GAZ ET VENTILÉ

VENTED GAS FIREPLACE HEATER. APPROVED FOR BEDROOM, BATHROOM AND BED-SITTING ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION IF INSTALLED IN ACCORDANCE WITH THE

CURRENT STANDARD CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME CONST

RUCTION AND SAFETY STANDARD, TITLE 24 CFR,

PART 3280. WHEN THIS US STANDARD IS NOT APPLICABLE USE THE STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED HOME INSTALLATION

S, SITES AND COMMUNITIES, ANSI / NFPA 501A.

FOYER DE CHAUFFAGE AU GAZ AVEC ÉVACUATION. HOMOLOGUÉ POUR INSTALLATION DANS UNE CHAMBRE À COUCHER, UNE SALLE DE BAIN ET UN STUD

IO. APPROPRIÉ POUR INSTALLATION DANS UNE

MAISON MOBILE SI SON INSTALLATION CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SÉRIE DE MAISONS MOBILES ÉQUIPÉES AU GAZ, E

N VIGUEUR AU CANADA OU AUX ÉTATS-UNIS DE LA

NORME DE SECURITÉ ET DE CONSTRUCTION DE MAISONS MANUFACTURÉES, TITRE 24 CFR, SECTION 3280. DANS LE CAS OU CETTE NORME D'ÉTATS-U

NIS NE PEUT ÊTRE APPLIQUÉE, SE RÉFÉRER A LA NORME

RELATIVE AU CRITÈRE DE MESURES DE SÉCURITÉ CONTRE L'INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS MANUFACTURÉS, LES SITES ET

LES COMMUNAUTÉS, ANSI/NFPA 501A.

NOT FOR USE WITH

SOLID FUEL. FOR USE

WITH GLASS DOORS

CERTIFIED WITH THIS

UNIT ONLY.

WARNING

:

DO NOT ADD ANY MATERIAL

TO THE APPLIANCE, WHICH WILL COME

IN CONTACT WITH THE FLAMES, OTHER

THAN THAT SUPPLIED BY THE

MANUFACTURER WITH THE APPLIANCE.

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS:

TOP 0”

FLOOR 0”

RECESSED DEPTH ONE SIDED 23"

RECESSED DEPTH SEE THRU 13.5”

FRAMING (NOT INCLUDING

FACE MATERIAL)

SIDES 0”

VENT 2"

BACK 0”

MANTLE 15" *

TOP, SIDES & BACK: PER STAND OFF SPACERS FOR FRAMING MATERIALS. FOR FINISHING MATERIALS

SEE OWNERS MANUAL

UN COMBUSTIBLE SOLIDE NE

DOIT PAS ÊTRÉ UTILISÉ AVEC

CET APPAREIL. UTILISER AVEC

LES PORTES VITRÉES

HOMOLOGUÉES SEULEMENT

AVEC CETTE UNITÉ.

AVERTISSEMENT:

N'AJOUTEZ PAS A

CET APPAREIL AUCUN MATÉRIAU DEVANT

ENTRER EN CONTACT AVEC LES FLAMMES

AUTRE QUE CELUI QUI EST FOURNI AVEC

CET APPAREIL PAR LE FABRICANT.

DÉGAGEMENTS MINIMAUX DES

MATÉRIAUX COMBUSTIBLES:

DESSUS 0”

PROFONDEUR D'ENCASTRÉ 25"

PLANCHER 0”

ÉVENT 2"

CÔTES 0”

MANTEAU 15" *

ARRIÉRE 0”

MADE IN CANADA / FABRIQUÉ AU CANADA

WOLF STEEL LTD. BARRIE, ONTARIO, CANADA

ALTITUDE / ÉLÉVATION

INPUT / ALIMENTATION

REDUCED INPUT / ALIMENTATION RÉDUITE

ORIFICE / INJECTEUR

MANIFOLD PRESSURE /

PRESSION AU COLLECTEUR

MINIMUM SUPPLY PRESSURE /

PRESSION D'ALIMENTATION MINIMALE

MAXIMUM SUPPLY PRESSURE /

PRESSION D'ALIMENTATION MAXIMALE

0-4500FT (0-1370M)

30,000 BTU/H

23,000 BTU/H

#38

3.5" WATER COLUMN/D'UNE COLONNE D'EAU

4.5" WATER COLUMN/D'UNE COLONNE D'EAU

7.0" WATER COLUMN/D'UNE COLONNE D'EAU

0-4500FT (0-1370M)

30,000 BTU/H

23,000 BTU/H

#53

10" WATER COLUMN/D'UNE COLONNE D'EAU

11" WATER COLUMN/D'UNE COLONNE D'EAU

13" WATER COLUMN/ D'UNE COLONNE D'EAU

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE

NAPOLEON VENT KITS. SEE OWNERS INSTALLATION MANUAL

FOR VENTING SPECIFICS. PROPER REINSTALLATION AND

RESEALING IS NECESSARY AFTER SERVICING THE VENT-AIR

INTAKE SYSTEM.

L'APPAREIL DOIT ÉVACUER SES GAZ EN UTILISANT L'ENSEMBLE

D'ÉVACUATION PROPRE A NAPOLEON. RÉFÉRER AU MANUEL

D'INSTALLATION DE PROPRIÉTAIRE POUR L'ÉVACUATION

PRÉCISE. IL EST IMPORTANT DE BIEN RÉINSTALLER ET

RESCELLER L'ÉVENT APRÈS AVOIR ASSURÉ LE MAINTIEN DU

SYSTÉME DE PRISE D'AIR.

CLASSIFICATION: 115V 0.82AMP, 60HZ

W385-2007

MODEL NATURAL GAS /

GAZ NATURAL

LHD50NT

MODEL PROPANE

LHD50PT

SERIAL NUMBER/NO. DE SÉRIE:

LV50

ELECTRICAL RATING: 115V 0.82AMP, 60HZ

REFERENCE #

W/N 16131

* MAXIMUM HORIZONTAL EXTENSION / L'EXTENSION

HORIZONTALE MAXIMALE: 2". SEE INSTRUCTION MANUAL FOR GREATER EXTENSIONS.

SEE OWNER'S INSTRUCTION MANUAL FOR MINIMUM AND MAXIMUM VENT LENGTHS.

DESSUS, COTÉS & ARRIÈRE: SELON LES ESPACEURS DE DÉGAGEMENT POUR LES MATÉRIAUX D'OSSATURE

SELON LE MANUEL DE PROPRIÉTAIRE POUR LES MATÉRIAUX DE FINITION.

* L'EXTENSION HORIZONTALE MAXIMALE: 2". RÉFÉRER AU MANUEL D'INSTRUCTION POUR DES EXTENSIONS

PLUS GRANDES. RÉFÉRER AU MANUEL D'INSTALLATION DE PROPRIÉTAIRE.

Both the rating plate and lighting instructions are attached to a chain located on the left side of the control

area near the valve (access side). Remove the glass guard and the control cover to gain access to the

control area.

To replace, slide the instructions back into the control area and slide the glass front into its locked position.

1.5 rating plate/lighting instruction location

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

The rating plate must remain with the appliance at all times. It must not be removed.

note:

Pilot location

Rating plate

location

access side

Certiﬁed to Canadian and American National Standards: CSA 2.22-XXXX / ANSI Z21.50-XXXX for Vented Decorative Gas Appliances

Certiﬁé selon les normes Nationales Canadiennes et Américaines: CSA 2.22-XXXX / ANSI Z21.50-XXXX pour les Appareils à gaz décoratif à évacuation

Direct vent, vented gas ﬁreplaces. Approved for bedroom, bathroom and bed-sitting room installation. Suitable for mobile home installation, if installed in accordance with the current

standard CAN / CSA Z240MH Series gas equipped mobile homes in Canada, or, in the United States, the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part

3280. When this US Standard is not applicable, use the Standard for Fire Safety Criteria for Manufactured Home Installations, Sites and Communities, ANSI / NFPA 501A. This appliance

must be installed in accordance with local codes, if any; if none, follow the current ANSI Z223.1 or CSA B149. For use with barrier WXXX-XXXX. Follow installation instructions.

Foyer à gaz ventilé. Homologué pour installation dans une chambre à coucher, une salle de bain et un studio. Approprié pour installation dans une maison mobile si son installation

conforme aux exigences de la norme CAN / CSA Z240MH Séries de maisons mobile équipées au gaz en vigueur au Canada, ou, aux États-Unis selon la norme 24 CFR, Part 3280,

Manufactured Home Construction and Safety Standard. Dans le cas ou cette norme d’États-Unis n’est pas pertinentes, utiliser la norme NFPA 501A, Fire Safety Criteria for Manufactured

Home Installations, Sites and Communities. Installer l’appareil selon les codes ou règlements locaux ou, en l’absence de tels règlements, selon les codes d’installation ANSI Z223.1 ou

CSA B149 en vigueur. Utiliser uniquement avec l’écran WXXX-XXXX. Suivre les instructions d’installation.

9700539 (WSL) 4001658 (NAC) 4001657 (NGZ) 4001659 (WUSA)

WOLF STEEL LTD. 24 Napoleon Road, Barrie, ON, L4M 0G8 Canada

XXXX XXXX XXXX XXXX

MODEL / MODÈLE

Altitude

Input

Reduced Input

P4

Élévation

Alimentation

Alimentation Réduite

P4

Manifold Pressure: 3.5” w.c. (NG)

Minimum Supply Pressure: 4.5” w.c. (NG)

Maximum Supply Pressure: 7”* w.c. (NG)

Pression au Collecteur: 3,5” d’une colonne d’eau (GN)

Pression d’Alimentation Min.: 4,5” d’une colonne d’eau (GN)

Pression d’Alimentation Max.: 7” ** d’une colonne d’eau (GN)

** Maximum inlet pressure not to exceed 13”.

Manifold Pressure: 10” w.c. (P)

Minimum Supply Pressure: 11” w.c. (P)

Maximum Supply Pressure: 13”* w.c. (P)

Pression au Collecteur: 10” d’une colonne d’eau (P)

Pression d’Alimentation Min.: 11” d’une colonne d’eau (P)

Pression d’Alimentation Max.: 13” * d’une colonne d’eau (P)

** Pression d’alimentation maximale ne devait pas dépasser 13”.

0-XXXXft (0-XXXXm)

Minimum clearance to combustible materials:

Top, sides & back: per standoff spacers for framing and ﬁnishing

materials. For non-combustible framing and ﬁnishing materials,

see installation manual.

Top X”

Floor X”

Sides X”

Back X”

Vent top X”

Vent sides & bottom X”

Recessed depth X”

*** Mantel X” from appliance opening

Dégagements minimaux des matériaux combustibles:

Dessus, côtés et arrière: selon les espaceurs de dégagements

pour les matériaux d’ossature selon le manuel du propriétaire

pour les matériaux de ﬁnition.

Dessus X”

Plancher X“

Côtés X”

Arrière X“

Dessus du conduit d’évent X”

Côtés et dessous du conduit d’évent X”

Profondeur d’encastré une face X”

*** Tablette X” de l’ouverture de l’appareil

WARNING: Do not add any material to the appliance which will come in contact with the

ﬂames, other than that supplied by the manufacturer with the appliance.

AVERTISSEMENT: N’ajoutez pas à cet appareil aucun matériau devant entretien

contact avec les ﬂammes autre que celui qui est fourni avec cet appareil par le fabricant.

*** Maximum horizontal extension:

X”. See installation manual for

greater extensions, minimum vent

lengths and maximum vent lengths.

*** L’extension horizontale maximale: X”.

Référez au manuel d’installation pour des

extensions plus grandes, les longueurs

d’évacuation minimaux et maximum.

The appliance must be vented using the appropriate Napoleon vent kits. See installation

manual for venting speciﬁcations. Proper reinstallation and resealing is necessary after servicing

the vent-air intake system.

L’appareil doit être ventilé à l’aide de l’ensemble d’évacuation propre à Napoleon. Référez au

manuel d’installation pour les spéciﬁcations d’évacuation. Il est nécessaire de bien réinstaller et

resceller l’évacuation après avoir executer l’entretien du système de prise d’air.

Serial Number / N° de Série:

W385-XXXX

REFERENCE# 161746

XXXX

VENTED DECORATIVE GAS APPLIANCE: NOT A SOURCE OF

HEAT, NOT INTENDED FOR USE AS A HEATING

APPLIANCE, NOT FOR USE WITH SOLID FUEL.

APPAREIL À GAZ DÉCORATIF À ÉVACUATION: N’EST PAS

UNE SOURCE DE CHALEUR; N’EST PAS DESTINÉ À ÈTRE

UTILISÉ COMME UN APPAREIL DE CHAUFFAGE; NE

CONVIENT PAS AUX COMBUSTIBLES SOLIDES.

FOR USE WITH GLASS DOORS CERTIFIED WITH THIS APPLIANCE ONLY.

POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE

CERTIFIÉES AVEC L’APPAREIL.

XX,XXX XX,XXX

For natural gas when equipped with No. XX drill size oriﬁce.

For propane when equipped with No. XX drill size oriﬁce.

Convient au gaz naturel quand l’appareil est muni d’un injecteur de diamètre no. XX.

Convient au propane quand l’appareil est muni d’un injecteur de diamètre no. XX.

Electrical rating: 115V, 60HZ. Less than 12 amperes.

Spéciﬁcations électriques: 115V, 60HZ. Moins de 12 ampère.

XX.X% XX.X%

XXXX XXXX XXXX XXXX

W415-2035 / C / 04.30.21

EN

12

general information

1.6 mobile home installation

1.8 lifting handles installation/removal

1.7 hardware list

1

2

3

Description Quantity

1

Hex Head Sheet Metal Screw 22

2

Pan Head Sheet Metal Screw 4

3

Hex Head Sheet Metal Bolt 18

This appliance must be installed in accordance with the manufacturer’s instructions and the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home

Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas

indicated on the rating plate.

This mobile/manufactured home listed appliance comes factory equipped with a means to secure the appliance. The

shipping brackets that secure the appliance to the pallet can be used to secure the appliance to the ﬂ oor for mobile

home installation. For mobile home installations, the appliance must be fastened in place.

This appliance is certiﬁ ed to be installed in an aftermarket permanently located, manufactured (mobile) home,

where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible

for use with other gases, unless a certiﬁ ed kit is used.

Conversion Kits

This appliance is ﬁ eld convertible between Natural Gas (NG) and Propane (P). To convert from one gas to another,

consult your Authorized dealer/distributor.

note:

Only fasteners supplied with the appliance are illustrated.

The lifting handles MUST be removed prior to rough

framing the appliance.

Remove 4 screws each side (8 total) then install the

lifting handles to the side of the appliance and secure

using 4 screws each side (8 total). Once the appliance

is in place remove the four screws from each handle to

the appliance. Discard the lifting handles.

EN

W415-2035 / C / 04.30.21

13

dimensions

2.0 dimensions

2.1 single-sided

LVX38-1 LVX50-1 LVX62-1 LVX74-1

A

(Finishing Flange)

42 1/8”

(1070mm)

54 1/8”

(1375mm)

66 1/8”

(1680mm)

78 1/8”

(1984mm)

B

53 5/16”

(1354mm)

65 5/16”

(1659mm)

77 5/16”

(1964mm)

89 5/16”

(2269mm)

C

57 5/16”

(1456mm)

69 5/16”

(1761mm)

81 5/16”

(2065mm)

93 5/16”

(2370mm)

41 3/16"

1046mm

7 1/16"

179mm

18 5/8"

473mm

3 1/8"

80mm

17 3/16"

437mm

32 3/4"

832mm

39 11/16"

1008mm

8 1/16"

205mm

8 1/16"

205mm

Ø 8"

203mm

Ø 5"

127mm

GLASS GUARD

1/2"

[12.7mm]

A

B

C

*

*Finishing flange depth (the finishing flange defines the perimeter of the fireplace opening. Framing

or finishing materials must NEVER encroach inside the finishing flange).

Base of air collar

17 11/16”

(449mm)

W415-2035 / C / 04.30.21

EN

14

dimensions

LVX38-1 LVX50-1 LVX62-1 LVX74-1

A

(Finishing Flange)

42 1/8”

(1070mm)

54 1/8”

(1375mm)

66 1/8”

(1680mm)

78 1/8”

(1984mm)

B

53 5/16”

(1354mm)

65 5/16”

(1659mm)

77 5/16”

(1964mm)

89 5/16”

(2269mm)

C

57 5/16”

(1456mm)

69 5/16”

(1761mm)

81 5/16”

(2065mm)

93 5/16”

(2370mm)

2.2 see-thru

41 3/16"

1046mm

7 1/16"

179mm

18 5/8"

473mm

3 1/8"

80mm

32 3/4"

832mm

39 11/16"

1008mm

16 3/16"

411mm

8 1/16"

205mm

8 1/16"

205mm

Ø 8"

203mm

Ø 5"

127mm

GLASS GUARD

1/2"

[12.7mm]

1/2"

[12.7mm]

A

B

C

*

Base of air collar

*Finishing flange depth (the finishing flange defines the perimeter of the fireplace opening. Framing or

finishing materials must NEVER encroach inside the finishing flange).

EN

W415-2035 / C / 04.30.21

15

minimum venting requirements

3.0 minimum venting requirements

!

WARNING

• Risk of ﬁ re. Maintain speciﬁ ed air space clearances to vent pipe and appliance.

• The vent system must be supported every 3’(0.9m) for both vertical and horizontal runs. Use support ring assembly

W010-0067 or equivalent non-combustible strapping to maintain the minimum clearance to combustibles for both

vertical and horizontal runs. Spacers are attached to the inner pipe at predetermined intervals to maintain an even air

gap to the outer pipe. This gap is required for safe operation. A spacer is required at the start, middle, and end of each

elbow to ensure this gap is maintained. These spaces must not be removed.

This appliance uses a 5” (127mm) exhaust / 8” (203.2mm) air intake vent pipe system. Refer to the section

applicable to your installation.

For safe and proper operation of the appliance follow the venting instructions exactly. Deviation from the minimum vertical

vent length can create difﬁ culty in burner start-up and/or carboning. Under extreme vent conﬁ gurations, allow several

minutes (5-15) for the ﬂ ame to stabilize after ignition. Although not a requirement, it is recommended for vent lengths that

pass through unheated spaces (attics, garages, crawl spaces) be insulated with the insulation wrapped in a protective sleeve

to minimize condensation. Provide a means for visually checking the vent connection to the appliance after the appliance is

installed. Use a ﬁ restop, vent pipe shield or attic insulation shield when penetrating interior walls, ﬂ oor or ceiling.

The vent terminal may be painted with a high temperature paint to match exterior colours. Use an outdoor paint suitable for

400°F (200°C). Application and performance of paint is the consumer’s responsibility. Spot testing is recommended.

Connections made by means of an adaptor at the appliance, as well as the connection at the vent terminal must be sealed.

RTV sealant may be used on both the inner exhaust and outer intake vent pipe joints of all other approved vent systems, ex-

cept for the exhaust vent pipe connection to the appliance ﬂ ue collar which must be sealed using the black high temperature

sealant Mill Pac.

For all vent systems is strongly recommend for all installations but required when power venting the appliance, that the outer

air intake joints are sealed using either high temperature silicone (RTV) or a suitable aluminum tape that covers each joint in

the vent system entirely around its circumference. This will ensure the best performance in every application and avoids per-

formance or condensation concerns that may occur in “tightly” constructed homes, particularly those in cold climates.

Use only Wolf Steel, Metal-Fab, BDM, Simpson Dura-Vent, or Selkirk Direct Temp venting components. Minimum and

maximum vent lengths, for both horizontal and vertical installations, clearances from vent pipes to combustibles and air

terminal locations as set out in this manual apply to all vent systems and must be adhered to. For Metal-Fab, BDM, Simpson

Dura-Vent, or Selkirk Direct Temp, follow the installation procedure provided with the venting components or on the website

for your venting supplier.

A starter adaptor must be used with the following vent systems and may be purchased through Wolf Steel or from the

corresponding supplier listed below:

If for any reason the vent air intake system is disassembled; reinstall per the instructions provided for the initial

installation.

This appliance must be installed with a continuous connection of exhaust and air intake vent pipes. Utilizing alternate

constructions, such as a chimney as part of the vent system, is not permitted.

note:

Venting System Manufacturer

Starter Adapter

Part Number

Supplier Website

SureSeal Metal-Fab 5DNA Wolf Steel www.mtlfab.com

Direct Vent Pro Simpson DuraVent W175-0170 Wolf Steel www.duravent.com

Pro-Form BDM N/A BDM www.dalsinmfg.com

Direct Temp Selkirk 5DT-AAN Selkirk www.selkirkcorp.com

Ventis

Olympia Chimney

and Venting

VDV-NA05-58F

Olympia Chimney

and Venting

www.olympiachimney.com

When using Wolf Steel venting components, use only approved Wolf Steel rigid / ﬂ exible components with the following

termination kits: wall terminal kit GD422R-2 or ST58U-1, or 1/12 to 7/12 pitch roof terminal kit GD410, 8/12 to 12/12 roof

terminal kit GD411, ﬂ at roof terminal kit GD412 or periscope kit GD401 (for wall penetration below grade). With ﬂ exible

venting, in conjunction with the various terminations, use either the 5 foot (1.5m) vent kit GD420 or the 10 foot (3.1m) vent kit

GD430.

W415-2035 / C / 04.30.21

EN

16

minimum venting requirements

For optimum ﬂ ame appearance and appliance performance, keep the vent length and number of elbows to a minimum.

The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that

it is unobstructed and undamaged.

Rigid and ﬂ exible venting systems must not be combined. Different venting manufacturer components must not

be combined.

These vent kits allow for either horizontal or vertical venting of the appliance. The maximum allowable horizontal run is 20

feet (6.1m). The maximum allowable vertical vent length is 40 feet (12.2m). The maximum number of vent connections is two

horizontally or three vertically (excluding the appliance and the air terminal connections) when using ﬂ exible venting.

Horizontal runs may have a 0” (0mm) rise per foot/meter however for optimum performance it is recommended that all

horizontal runs have a minimum 1/4” (21mm) rise per foot/meter using ﬂ exible venting. For safe and proper operation of the

appliance, follow the venting instructions exactly.

A terminal shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwell-

ings and serves both dwellings. Local codes or regulations may require different clearances.

Do not allow the inside liner to bunch up on horizontal or vertical runs and elbows. Keep it pulled tight. A 1¼” (31.8mm) air

gap all around between the inner liner and outer liner is required for safe operation.

EN

W415-2035 / C / 04.30.21

17

minimum venting requirements

LVX38-1 LVX50-1 LVX62-1 LVX74-1

D

40” (101.6cm) 46 1/2” (118.1cm) N/A N/A

LVX38-1 LVX50-1 LVX62-1 LVX74-1

D

40” (101.6cm) 46 1/2” (118.1cm) 52 1/2” (133.4cm) 58 1/2” (148.6cm)

30”

(76.2cm)

LVX38-1 & LVX50-1: 30” (76.2cm) min

LVX62-1 & LVX74N-1: 48” (121.9cm)

min

LVX74P-1: 58” (147,3cm) min

LVX38-1 & LVX50-1: 62 3/4” (76.2cm)

min plus rise

LVX62-1 & LVX74N-1: 80 3/4” (205.1cm)

min plus rise

LVX74P-1: 90 3/4” (230.5cm)

min plus rise

62 3/4"

(159.4cm)

18"

(45.7cm)

SINGLE-SIDED

SEE-THRU

SINGLE-SIDED / SEE-THRU

3.1 typical venting installation

minimum plus rise

maximum

minimum

base of

air collar

base of

air collar

D

special vent installation (periscope termination)

Use the periscope kit to locate the air termination above grade. The periscope must be installed so that when

ﬁ nal grading is completed, the bottom air slot is located a minimum 12” (30.5cm) above grade. The maximum

allowable vent length is 10’ (3m).

12"

(30.5cm)

minimum

to grade

30”

(76.2cm) min.

base of air collar

12"

(30.5cm)

minimum

to grade

D

base of air collar

LVX38-1 & LVX50-1: 30” (76.2cm)

min

W415-2035 / C / 04.30.21

EN

18

minimum venting requirements

40 ft (12m)

maximum

6 ft (1m)

minimum

16" (40.6cm)

minimum

SINGLE-SIDED OR SEE-THRU

base of air

collar

A 6’ (1.83m) minimum vertical rise is

considered the minimum practical dimen-

sion for the speciﬁ c appliance enclosure

and a minimal building structure. However,

a greater minimum vertical rise may be

needed to suit the speciﬁ c application con-

straints or local codes and / or regulatory

requirements.

note:

EN

W415-2035 / C / 04.30.21

19

minimum venting requirements

3.2 minimum air terminal location clearances

Q

MIN

R

MAX

R

= 3 feet

(0.9m)

= 2 x

IHHW

(4.6m)

Q

ACTUAL

INSTALLATIONS

CANADA U.S.A.

A

12” (30.5cm) 12” (30.5cm) Clearance above grade, veranda porch, deck or balcony.

B

12” (30.5cm)

Δ

9” (229mm)

Δ

Clearance to windows or doors that open.

C

12” (30.5cm)* 12” (30.5cm)* Clearance to permanently closed windows.

D

18”

(45.7cm)**

18”

(45.7cm)**

Vertical clearance to ventilated sofﬁ ts located above the terminal within a horizontal distance of 2’ (0.6m)

from the center line of the terminal.

E

12” (30.5cm)** 12” (30.5cm)** Clearance to unventilated sofﬁ t.

F

0” (0mm) 0” (0mm) Clearance to an outside corner wall.

G

0” (0mm)*** 0” (0mm)***

Clearance to an inside non-combustible corner wall or protruding non-combustible obstructions (chimney, etc.).

2” (51mm)*** 2” (51mm)*** Clearance to an inside combustible corner wall or protruding combustible obstructions (vent chase, etc.).

H

3’(0.9m) 3’(0.9m)****

Clearance to each side of the center line extended above the meter / regulator assembly to a maximum

vertical distance of 15’ (4.6m).

I

3’ (0.9m) 3’ (0.9m)**** Clearance to a service regulator vent outlet.

J

12” (30.5cm) 9” (229mm) Clearance to a non-mechanical air supply inlet to the building or a combustion air inlet to any other appliance.

K

6’ (1.8m) 3’ (0.9m) † Clearance to a mechanical air supply inlet.

L

7’ (2.1m) ‡ 7’ (2.1m) **** Clearance above a paved sidewalk or paved driveway located on public property.

M

12” (30.5cm)†† 12” (30.5cm)**** Clearance under a veranda, porch, deck or overhang.

N

16” (40.6cm) 16” (40.6cm) Clearance above the roof.

O

2’ (0.6m)†* 2’ (0.6m) †* Clearance from an adjacent wall including neighbouring buildings.

P

8’ (2.4m) 8’ (2.4m)

Roof must be non-combustible without openings.

Q

3’ (0.9m) 3’ (0.9m) See chart for wider wall dimensions.

R

6’ (1.8m) 6’ (1.8m)

See chart for deeper wall dimensions. The terminal shall not be installed on any wall that has an opening

between the terminal and the open side of the structure.

S

12” (30.5cm) 12” (30.5cm) Clearance under a covered balcony

Δ The terminal shall not be located less than 6 feet under a window that opens on a horizontal plane in a structure with three walls and a roof.

* Recommended to prevent condensation on windows and thermal breakage

** It is recommended to use a heat shield and to maximize the distance to vinyl clad sofﬁ ts.

*** The periscope requires a minimum 18 inches clearance from an inside corner.

**** This is a recommended distance. For additional requirements, check local codes.

† 3 feet above if within 10 feet horizontally.

‡ A vent shall not terminate where it may cause hazardous frost or ice accumulations on adjacent property surfaces.

†† Permitted only if the veranda, porch, or deck is fully open on a minimum of two sides beneath the ﬂ oor.

†* Recommended to prevent recirculation of exhaust products. For additional requirements, check local codes.

††* Permitted only if the balcony is fully open on a minimum of one side.

Wall terminals are for illustration purposes only. Size and shapes may vary. Wall terminal

measurements taken from the exhaust outlet, not the mounting plate.

Covered balcony applications ††*

R

Q

S

G

P

Clearances are to be in accordance with local

installation codes and the requirements of the gas

supplier. In their absence, clearances are to be as

listed above and are based on national codes.

note:

W415-2035 / C / 04.30.21

EN

20

minimum venting requirements - natural gas

3.3 horizontal termination

0’

Base of

air collar

10’

15’

20’

25’

20’

30’

40’

5’

3 7/8’ (46 1/2”) max.

(LV50-2 see-thru)

1 1/2’

(18”)

max.*

2 1/2’

(30”) min.*

38 1/2’

(462”)

5’

1 elbow zone

1-2 elbow zone

1-3 elbow zone

1-4 elbow zone

1-5 elbow zone

1-6 elbow zone

H

V

V+H ≤ 40 ft. (For longer vent runs, a power

vent is required).

H ≤ 20 ft.

V + H are measured from the centre of vent

elbows. Elbows are considered as 90º.

Two 45º elbows = One 90º elbow.

3 3/8’ (40”) max.

(LV38-1 see-thru)

LVX38-1 / LVX50-1 / LVX62-1 / LVX74-1 SINGLE-SIDED &

LVX38-1 / LVX50-1 SEE-THRU

(NATURAL GAS ONLY)

(LVX38-1 see-thru)

(LVX50-1 see-thru)

La page charge ...

NAPOLEON LVX62N2X Manuel utilisateur

NAPOLEON LVX62N2X Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents